Hi guys,
On my phone I went to CWM and clicked reboot into recovery. However the phone can't go past the 'Samsung galaxy s3' start up bit. When I do volume down, home and power button it just goes into download mode and stays there. ANything I can do?
Also when I try volume up, home and power, the logo goes away but then just comes back
try pulling the battery for a few minutes, then retry recovery, release the buttons when you see the galaxy s screen
slaphead20 said:
try pulling the battery for a few minutes, then retry recovery, release the buttons when you see the galaxy s screen
Click to expand...
Click to collapse
Hey, just tried that. Still no luck. Is there anything I can do via my laptop to reflash it or something?
Qaz_92 said:
Hey, just tried that. Still no luck. Is there anything I can do via my laptop to reflash it or something?
Click to expand...
Click to collapse
Just flash a stock Rom with Odin, you can get download mode so all is good
slaphead20 said:
Just flash a stock Rom with Odin, you can get download mode so all is good
Click to expand...
Click to collapse
I love you.
Qaz_92 said:
I love you.
Click to expand...
Click to collapse
no need for that lol
Need futher
slaphead20 said:
Just flash a stock Rom with Odin, you can get download mode so all is good
Click to expand...
Click to collapse
Hey I have the same problem as the guy you just help, and I have been trying this for the past 2 hours. I have tried to flash the original samsung rom and flash cwm recovery and both wont go past the gs3 boot screen. Anything I could do? I can get to the recovery and download mode. By the way im on sprint gs3
[KK] Satcom23 said:
no need for that lol
Click to expand...
Click to collapse
sprint?
Then download the one for sprint.
Looks like you're flashing the international i9300 odin packages.
this seems to be a soft brick. Just flash the one with odin from the Sprint Galaxy S3 forums.
masterex567 said:
sprint?
Then download the one for sprint.
Looks like you're flashing the international i9300 odin packages.
this seems to be a soft brick. Just flash the one with odin from the Sprint Galaxy S3 forums.
Click to expand...
Click to collapse
Sir i have the same problem , my SGS3 is soft bricked ,cant go pass the samsung boot logo,tried the volup+home+pwr method to go the recovery but it just reverts back to the boot logo, i havent tried to flash the official stock rom for international version yet,i would like to try the one that you guys have used and worked, can someone pls provide a link so i can flash it via ODIN? thanks and its much appriciated .
im trying to download at this site http://samsung-updates.com/device/?id=GT-I9300 ... but there is a problem with their servers... BTW my region is in the philippines.
U can get stock rom for your phone on the official samsung site .I just had this happen to me. It was stuck on samsung logo and when I would try to get into recovery via 3button method phone would just power off and on and vibrate so after a while by luck looked down at my phone and it was in download mode so just had to use oden and flas a new recovery and a stock jb rom.
Sent from my SAMSUNG-SGH-I747 using xda premium
Help Soft bricked S3
after flashing via odin this came up... failed , i dont know whats PIT mapping is... need Help here ,
<ID:0/025> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXDLJ1_I9300OLBDLJ1_I9300DXDLI5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/025> Odin v.3 engine (ID:25)..
<ID:0/025> File analysis..
<ID:0/025> SetupConnection..
<ID:0/025> Initialzation..
<ID:0/025> Get PIT for mapping..
<ID:0/025>
<ID:0/025> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Mario Christian Oquias said:
after flashing via odin this came up... failed , i dont know whats PIT mapping is... need Help here ,
<ID:0/025> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXDLJ1_I9300OLBDLJ1_I9300DXDLI5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/025> Odin v.3 engine (ID:25)..
<ID:0/025> File analysis..
<ID:0/025> SetupConnection..
<ID:0/025> Initialzation..
<ID:0/025> Get PIT for mapping..
<ID:0/025>
<ID:0/025> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I think it's part of the uh sudden death thing with the pit dissapearing.
Try this at your own risk, but flashing the correct PIT? or it might be time for service center
xSpeced said:
I think it's part of the uh sudden death thing with the pit dissapearing.
Try this at your own risk, but flashing the correct PIT? or it might be time for service center
Click to expand...
Click to collapse
its that serious huh? ouch... that will leave a mark.. tsk tsk tsk....how would i know if its the correct PIT mapping and procedure to do that? ..is there even a procedure or should i just give this to the service center, if there is a procedure i know i can do it properly, can someone point me the way? thanks for the heads up BTW
hel needed
<ID:0/025> Odin v.3 engine (ID:25)..
<ID:0/025> File analysis..
<ID:0/025> SetupConnection..
<ID:0/025> Can't open the serial(COM) port.
<ID:0/025> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
i tried to flash the PIT and this came up, hmn..i dont know what this means..
Related
Hi all,
I have a weird problem with my GS2. Im used to use Odin because I had a GS and i tried every ROM post on XDA .
I always solve my prob by myself but this time I need ur help.
My phone running KE7 and lighting 1.1. Since 2 weeks when I try to install an app, when I progress in a game, when I restart everything isn't here anymore. But the weird thing it's for my SMS/Photo ... etc I have everything !
My FB or Tweet Statut get stuck to 2 weeks before... I have to refresh and got new statuts. When I restart it come back at 2 weeks...
I tried a full wipe with CWM, it pass, but I still keep all the program and customisation of before.
I tried a fresh install with Odin (fresh KE7 or the new KF1 with all files) and i always have the same fail.
<ID:0/030> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9100XWKF1_CL265340_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXKE7_REV_02_CL1017274.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OJVKE4.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/030> Odin v.3 engine (ID:30)..
<ID:0/030> File analysis..
<ID:0/030> SetupConnection..
<ID:0/030> Initialzation..
<ID:0/030> Set PIT file..
<ID:0/030> DO NOT TURN OFF TARGET!!
<ID:0/030> Get PIT for mapping..
<ID:0/030> Firmware update start..
<ID:0/030> boot.bin
<ID:0/030> NAND Write Start!!
<ID:0/030> Sbl.bin
<ID:0/030> param.lfs
<ID:0/030> zImage
<ID:0/030> factoryfs.img
<ID:0/030> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/030> Removed!!
Click to expand...
Click to collapse
5 times in a row...
Can u help me ? I dunno if ur understand me well cause english isn't my mothertongue !
Thks All in advance!
I have the same problem now, I can't flash with Odin because of the same message : "Complete(Write) operation failed."
Did you find a solution already?
EDIT : I used a different usb port and it worked.
Gils3310 said:
Hi all,
I have a weird problem with my GS2. Im used to use Odin because I had a GS and i tried every ROM post on XDA .
I always solve my prob by myself but this time I need ur help.
My phone running KE7 and lighting 1.1. Since 2 weeks when I try to install an app, when I progress in a game, when I restart everything isn't here anymore. But the weird thing it's for my SMS/Photo ... etc I have everything !
My FB or Tweet Statut get stuck to 2 weeks before... I have to refresh and got new statuts. When I restart it come back at 2 weeks...
I tried a full wipe with CWM, it pass, but I still keep all the program and customisation of before.
I tried a fresh install with Odin (fresh KE7 or the new KF1 with all files) and i always have the same fail.
5 times in a row...
Can u help me ? I dunno if ur understand me well cause english isn't my mothertongue !
Thks All in advance!
Click to expand...
Click to collapse
The same happened to me after I downloaded a corrupted file. You cold try to download the file again and reinstall the ADB drivers.
Congrats on necroing a 2 yr old thread.
MistahBungle said:
Congrats on necroing a 2 yr old thread.
Click to expand...
Click to collapse
Haha sorry I noticed after my Submit
Dear Friends
I tried to upload new Rom to my Samsung Galaxy S2 but it field and now even I can't get download mode only what I get is picture of (device---Attention---PC),
could you help me to get download mode again?
...
MistahBungle said:
That is download mode. Forced download mode. It's forcing you to flash something to get it going again. Flash a stock rom in Odin.
Click to expand...
Click to collapse
Thanks Man to reply, could you help me to official Rom to download it please?
...
The link below is a thread containing instructions on how to flash a stock firmware and also a list of the stock firmwares that are available.
http://forum.xda-developers.com/showthread.php?t=1075278
Sent from my GT-I9100 using Tapatalk 2
MistahBungle said:
Here or Samfirmware. Or even the PC version of Checkfus. I'd try the first two places initially.
Click to expand...
Click to collapse
Thanks Man,
I will do my best...
...
MistahBungle said:
No probs. Follow the flashing instructions in the thread that Nicholas1520 linked to. Any issues, post here. But have a go at it yourself first. You'll learn plenty going thru this
Click to expand...
Click to collapse
OK thanks boys,
I'm going throw it carefully and I will post anything later
MistahBungle said:
No probs. Follow the flashing instructions in the thread that Nicholas1520 linked to. Any issues, post here. But have a go at it yourself first. You'll learn plenty going thru this
Click to expand...
Click to collapse
Dear Friends,
I downloaded two of these Roms, and I can see the device downloadable in Odin3 and I selected in PDA then I pressed start, the software (Odin3) start to upload till I got Fail...
see this codes:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_ITV_I9100XWLPF_I9100OXILP6_I9100XXLPX.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Try using Odin 1.85:
http://db.tt/XSY1G5Ye
You should try another firmware and see of that's the case because your doing everything good so far.
Sent from my GT-I9100 using Tapatalk 2
nicholas1520 said:
Try using Odin 1.85:
http://db.tt/XSY1G5Ye
You should try another firmware and see of that's the case because your doing everything good so far.
Sent from my GT-I9100 using Tapatalk 2
Click to expand...
Click to collapse
Ok I will do my best with it,,, I will inform you later,,,
...
MistahBungle said:
Also, after you open Odin & before you start flashing, make sure you check Windoze Task Manager & close Kies/any associated processes if they're running.
And...Do you definitely have an I9100 or I9100T ? Check the sticker on the phone chassis under the battery to be doubly sure if you need to.
Click to expand...
Click to collapse
Ok, I'm already Using v.1.85 and I tried again by using different USB cable, my Device is I9100G, I did start again and its freezing now see this :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_ITV_I9100XWLPF_I9100OXILP6_I9100XXLPX.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
...
MistahBungle said:
OK. There's your problem right there. You have an I9100G. I think you'll find you tried to flash a rom for the I9100/T which caused it to get into a state where it won't boot/forced download mode.
You need to download & flash an I9100G stock rom. I don't have any experience with the I9100G (apart from seeing posts on here from people who have them), but look in this thread (I don't know which one you should use tho).
Edit - And be careful in future, only flash roms/kernels specifically for the I9100G
Click to expand...
Click to collapse
OK, I will check it carefully.... Thanks for your support...
alisaher2000 said:
OK, I will check it carefully.... Thanks for your support...
Click to expand...
Click to collapse
Dear Friends,
I solved it by applying uploading Rom for I9100G via Odin3 v.1.85... Thanks for all supports....
:good:
...
Dear Friends
I HAVE MESS-UP WITH MY i9300!!!!
The incident is I was using custom rom, and installed some stupid app called "Adblock" or something,
and then, my phone just keep went-off for about 8-10 times a day. So then, I decided to reflash
custom rom by CWM, and after I pressed install in Aroma Installer, it just kick me out all of sudden, and
then, I couldn't get back to CWM anymore, so I decided to flash some stock rom by odin, but what
had happen was it starts until "Nand write start" and stacked for a while, and then just FAIL me.
On the net, I found that Checkrom Resurrection V4 could rescue softbrick i9300, I tried, but
no luck either. Finally, just now, I tried a 3 files stock rom with pit, and it came out as:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md 5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noshi p.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
What I have done:
1. reflash custom rom by CWM
2. 3 wipes - (but I am no longer to get back to CWM)
3. flash stock rom - hong kong combo firmware @ Samfirmware - by Odin
4. flash Checkrom Resurrection V4 by Odin
5. flash stock rom - 3 files firmware + pit - by Odin
6. changed usb port
7. changed PC
8. uninstall all applications relative to Kies
have you guys got any idea what can I do? I am thinking to mess-up the phone even badly (till it couldn't switch on), so that I can take it to Samsung Service Center for warranty replacement, but have you got ANY method I can do that to mess it up? Or anything I can over-come from the soft (or hard) brick. PLEASE Give me some help guys. I am very struggle.
Wrong thread.. Needs to be in Q&A
Try a fully stock rom with Odin 1.85
Sent from my GT-I9300 using xda app-developers app
Kingybear said:
Try a fully stock rom with Odin 1.85
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Thanks Mate, but no luck
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
NatTheCat said:
Wrong thread.. Needs to be in Q&A[/QUOT
I put it on Q&A already, but just wanted to have more people can help, so I put it on here. sorry for any disturb.
Click to expand...
Click to collapse
The fact that you want more people helping you doesnt mean that you can do what you want, wrong section.
By the way, it seems that your s3 is bricked pal.
Sent from my GT-I9300 using Tapatalk
anyone can tell me how to delete the thread? Thanks
aguerito said:
The fact that you want more people helping you doesnt mean that you can do what you want, wrong section.
By the way, it seems that your s3 is bricked pal.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
show the poor guy some love dude, your comments are abrasive he only wants help for his expensive phone sheesh
---------- Post added at 10:03 AM ---------- Previous post was at 09:59 AM ----------
I wouldnt panic yet they say its very hard to brick an S3?
check around and see what you can find out
kk12175 said:
Thanks Mate, but no luck
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> sboot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I think it's rom problems dude... I never encounter any problems for adblock app... Which rom did u flashed
Sent from my GT-I9300 using xda premium
jothi2lingam said:
I think it's rom problems dude... I never encounter any problems for adblock app... Which rom did u flashed
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
i was using Omega since v.9 until v33.2 at the last minute. and I found a video in youtube to resurrect my s3 by flashing Checkrom v4:
http://www.youtube.com/watch?v=ZNaQfdOi56E
tried it as well, but it seems doesn't work as it kept rebooting / hanging at the Galaxy S3 logo. And I tried to flashed some stock rom (combo file) from Samfirmware, no luck neither. Tried to flash some stock rom (3 files + pit) HK base rom. Same happened. Fail after Nand Write Start.:silly:
and now, couldn't get into CWM neither.
jothi2lingam said:
I think it's rom problems dude... I never encounter any problems for adblock app... Which rom did u flashed
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Been using adblock for a while myself and never had a hiccup .. excellent app..
Probably mother board died. Same problem with my sister S3. Take to Samsung and use the warranty. :banghead:
Sent from my GT-I9300 using xda premium
johnkhor123 said:
Probably mother board died. Same problem with my sister S3. Take to Samsung and use the warranty. :banghead:
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
I had flashed custom rom before, do you think I can still use the warranty? If yes, definitely going.
kk12175 said:
Dear Friends
I HAVE MESS-UP WITH MY i9300!!!!
The incident is I was using custom rom, and installed some stupid app called "Adblock" or something,
and then, my phone just keep went-off for about 8-10 times a day. So then, I decided to reflash
custom rom by CWM, and after I pressed install in Aroma Installer, it just kick me out all of sudden, and
then, I couldn't get back to CWM anymore, so I decided to flash some stock rom by odin, but what
had happen was it starts until "Nand write start" and stacked for a while, and then just FAIL me.
On the net, I found that Checkrom Resurrection V4 could rescue softbrick i9300, I tried, but
no luck either. Finally, just now, I tried a 3 files stock rom with pit, and it came out as:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md 5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noshi p.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
What I have done:
1. reflash custom rom by CWM
2. 3 wipes - (but I am no longer to get back to CWM)
3. flash stock rom - hong kong combo firmware @ Samfirmware - by Odin
4. flash Checkrom Resurrection V4 by Odin
5. flash stock rom - 3 files firmware + pit - by Odin
6. changed usb port
7. changed PC
8. uninstall all applications relative to Kies
have you guys got any idea what can I do? I am thinking to mess-up the phone even badly (till it couldn't switch on), so that I can take it to Samsung Service Center for warranty replacement, but have you got ANY method I can do that to mess it up? Or anything I can over-come from the soft (or hard) brick. PLEASE Give me some help guys. I am very struggle.
Click to expand...
Click to collapse
Try TURN OFF antivirus, update Kies, Try on other OS.
Because I had the same problem with own S3.
Windows 8, AVG IS 2013, Odin 3.07,3.04.
Everytime after few second Odin stop working and show FAIL "Complete(Write) operation failed."
But on Windows 7, updated Kies to 2.5, turned off AVG, Odin 3.07, fresh downloaded rom ELK4, Galaxy S3 slowly but finished NAND write
and now I am happy againg
johnkhor123 said:
Probably mother board died. Same problem with my sister S3. Take to Samsung and use the warranty. :banghead:
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Ya i think so,,Same incident for previously after flashed one of the rom from this thread i went to sleep..The phone was reboot itself (stuck in bootloop) till i found at morning, my phone fuc**ing hot stucked in Samsung Galaxy SIII. After tried flashed using odin & using cwm not worked because my phone keep on rebooting. Once send to sammy centre i said that i put in charge, once wakeup in morning my phone keep on rebooting & so hot. So after one week they replace me new board for my s3 even they can see my cwm. I tried to delete cwm but cant. Thank god atlast they replace my s3. so only way is send to samsung centre. I face exactly same issue previously as you facing now
KKTHX said:
Try TURN OFF antivirus, update Kies, Try on other OS.
Because I had the same problem with own S3.
Windows 8, AVG IS 2013, Odin 3.07,3.04.
Everytime after few second Odin stop working and show FAIL "Complete(Write) operation failed."
But on Windows 7, updated Kies to 2.5, turned off AVG, Odin 3.07, fresh downloaded rom ELK4, Galaxy S3 slowly but finished NAND write
and now I am happy againg
Click to expand...
Click to collapse
sounds good. give it a try .. thanks MATE
kk12175 said:
anyone can tell me how to delete the thread? Thanks
Click to expand...
Click to collapse
Thread closed.
Ok, so here is the deal.
I have the Samsung Galaxy Mega 6.3 with U.S Cellular (SCH-R960) and I have run into some problems. What I did was try to root. Flashed CWM Recovery in Odin and when I tried to boot back up again, I was stuck in bootloop. So I tried to revert back to stock by flashing the stock firmware for my phone in Odin, the problem is, everytime I try and do that, I get this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9200XXUCNC2_I9200OLBCNC1_I9200XXUCNC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also, on the phone screen it says
SECURE CHECK FAIL: sbl1
I can boot into recovery and also into download mode. Although if I try to just boot the phone normal it just stays on the Samsung Galaxy Mega logo screen. I have tried sideloading a .zip and that also fails.
Does anyone have any idea of how to fix this? Any help would be greatly appreciated.
Deleted cause by my noob. Sorry
Sent from my Nexus 7 using Tapatalk
yusopa said:
Why you dont try go to galaxy mega thread to get help. I think you face something big what we call knox problem. You cant root your device before you know your device surely. Samsung provide new bootloader with knox right now.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Thought this was the Mega forum? And yes I know about knox I bricked an S3 because of it but I didn't think it was added until 4.3?
the firmware you are trying to flash (which is i9200) is not for your us cellular version of mega (which is r960).
find the correct one then proceed.
yusopa said:
Why you dont try go to galaxy mega thread to get help. I think you face something big what we call knox problem. You cant root your device before you know your device surely. Samsung provide new bootloader with knox right now.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
jk0l said:
the firmware you are trying to flash (which is i9200) is not for your us cellular version of mega (which is r960).
find the correct one then proceed.
Click to expand...
Click to collapse
I'm not using it as a phone anymore, just kinda as a tablet. So does it matter that it isnt the r960 firmware?
vBIGLEWISv said:
Ok, so here is the deal.
I have the Samsung Galaxy Mega 6.3 with U.S Cellular (SCH-R960) and I have run into some problems. What I did was try to root. Flashed CWM Recovery in Odin and when I tried to boot back up again, I was stuck in bootloop. So I tried to revert back to stock by flashing the stock firmware for my phone in Odin, the problem is, everytime I try and do that, I get this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9200XXUCNC2_I9200OLBCNC1_I9200XXUCNC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also, on the phone screen it says
SECURE CHECK FAIL: sbl1
I can boot into recovery and also into download mode. Although if I try to just boot the phone normal it just stays on the Samsung Galaxy Mega logo screen. I have tried sideloading a .zip and that also fails.
Does anyone have any idea of how to fix this? Any help would be greatly appreciated.
Click to expand...
Click to collapse
Try with samsung kies to revert back to stock..See it helps or not.
Carnage said:
Try with samsung kies to revert back to stock..See it helps or not.
Click to expand...
Click to collapse
Kies doesn't work either. It wont connect and when I try manually it wont accept my S/N. I'm stuck here I'm not sure what to do.
I am also found ths problem. Kies also not working... Bad experience..
Bro grab the right firmware for the phone just cause its not gonna be used as a phone does not mean that you don't have to have the correct **** for the phone lol
Sent from my sgh-i527 with xda premium 4
HOPSIN-KAT KEYBOARDS IS NOW UP AND RUNNING CHECK EM OUT OVER AT THE CANDY SHOP!
http://forum.xda-developers.com/showthread.php?p=52221912
vBIGLEWISv said:
Kies doesn't work either. It wont connect and when I try manually it wont accept my S/N. I'm stuck here I'm not sure what to do.
Click to expand...
Click to collapse
Are you really cannot boot into download mode?..vol down+power button..try power on the device,remove the battery,put it back again,and quickly press the download mode combination keys (vol down+power button) see it boots to download mode or not..if its boot, grab your latest firmware and flash it via odin. About the kies,try to uninstall and download the latest version of kies solve it..
EDIT:I have search your firmware and don't find any link.you have to wait until the firmware for your specific model number released by Samsung.
hopsin4444 said:
Bro grab the right firmware for the phone just cause its not gonna be used as a phone does not mean that you don't have to have the correct **** for the phone lol
Sent from my sgh-i527 with xda premium 4
HOPSIN-KAT KEYBOARDS IS NOW UP AND RUNNING CHECK EM OUT OVER AT THE CANDY SHOP!
http://forum.xda-developers.com/showthread.php?p=52221912
Click to expand...
Click to collapse
Thats the problem the stock firmware doesnt exist for my phone or at least I cant find it.
well then, thats unfortunate. im sorry.
so its certain that theres no way for you to go back to stock.
edit:
actually, try to wipe data and cache in recovery then reboot.
if it still bootloops, then I recommend you patiently wait until the stock firmware for your phone is released.
So, I'm obviously quite new here. I rooted my Note 2 back when I first got it about 2 years ago lol. Had it rooted with 4.1.2 on it and some old version of cleanrom.
Having the Note 4 Pre-Ordered, I decided to un-root my phone and update it in case someone wants to buy it off of me.
Basically I unrooted, added new stock rom to it, now it is stuck in bootloop and I cannot boot into recovery.
__________________
What have I done?
1) UnRooted from SuperSU
2) Wipped it in the system settings and TW recovery (CleanROM was still on it)
-
Since it still had the cleanrom on it, I went over to SamMoible to download my version of the stock 4.1.2 Firmware
I ran it in odin and everything went perfect, and it rebooted and now it's stuck in a bootloop. I CANNOT boot it into recovery from PWR+HOME+UVOL
-
Now I've tried running through adb to boot it into recovery and that did not work. I'm guessing because USB Debugging cannot be on with the phone fresh like this.
I can boot it into download, and I've tried re-adding that same stock rom onto the phone and it fails everytime.
I downloaded another SCH-605 4.1.2 stock rom, and it still fails just like the other one.
Log from Odin:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Can anyone help me? I have no clue on what to do and I cannot find anything online with someone having this same issue.
Thanks a ton!
If you haven't seen it already, you should check out Droidstyle's restore guide at this link: ( http://forum.xda-developers.com/showthread.php?p=34891181). His guide has links and detailed instructions on how to restore back to stock. (go to section 1b for instructions on how to restore back to stock 4.1.2).
As far as ODIN failing... From what I've read, you should connect your phone to a usb 2.0 port on the computer rather usb 3.0, so try different ports. Also make sure to run ODIN as administrator. I've also read that trying different usb cables and disabling antivirus programs can help when ODIN fails.
As you probably know, Android build 4.1.2 is the last build for our phones that allows us to unlock the bootloader... so I would personally restore it back to 4.1.2 and leave it there. I think it would have more value on Swappa if you're going to sell it there.
Hope this helps and Good luck!
mattnmag said:
If you haven't seen it already, you should check out Droidstyle's restore guide at this link: ( http://forum.xda-developers.com/showthread.php?p=34891181). His guide has links and detailed instructions on how to restore back to stock. (go to section 1b for instructions on how to restore back to stock 4.1.2).
As far as ODIN failing... From what I've read, you should connect your phone to a usb 2.0 port on the computer rather usb 3.0, so try different ports. Also make sure to run ODIN as administrator. I've also read that trying different usb cables and disabling antivirus programs can help when ODIN fails.
As you probably know, Android build 4.1.2 is the last build for our phones that allows us to unlock the bootloader... so I would personally restore it back to 4.1.2 and leave it there. I think it would have more value on Swappa if you're going to sell it there.
Hope this helps and Good luck!
Click to expand...
Click to collapse
Hey, I tried changing the ports and made sure it was a 2.0 port.
Still getting the FAIL from odin at the same spot.
EDIT; I ENDED UP FIXING IT WITH SOME HELP FROM MY DAD lol
We had to put a new Pit file on it and re-partition it.
Thanks everyone!
w4sp said:
EDIT; I ENDED UP FIXING IT WITH SOME HELP FROM MY DAD lol
We had to put a new Pit file on it and re-partition it.
Thanks everyone!
Click to expand...
Click to collapse
That's great. I was actually about to suggest some more ideas... and one was to make sure you were using the pit file if you weren't.... lol
Good to hear you got it fixed!!
w4sp said:
Hey, I tried changing the ports and made sure it was a 2.0 port.
Still getting the FAIL from odin at the same spot.
Click to expand...
Click to collapse
I've tried with the new pit file, tried to repartition, using stock_mc3_recovery.tar.md5 and I keep coming across an error. Any ideas?
thewhitespicsk8r said:
I've tried with the new pit file, tried to repartition, using stock_mc3_recovery.tar.md5 and I keep coming across an error. Any ideas?
Click to expand...
Click to collapse
What version of Android is your phone currently running? If it's on 4.3 or 4.4.2, then you can't use ODIN to downgrade back to 4.1.2 because of locked bootloader.
If you can post the error report you're getting in ODIN, it will be useful to assist others with helping you troubleshoot.
mattnmag said:
What version of Android is your phone currently running? If it's on 4.3 or 4.4.2, then you can't use ODIN to downgrade back to 4.1.2 because of locked bootloader.
If you can post the error report you're getting in ODIN, it will be useful to assist others with helping you troubleshoot.
Click to expand...
Click to collapse
I was using 4.4.2 before it crashed.... I know I can't go back to 4.1.2 because it's locked, and I can't seem to figure out why it won't let me go back to the stock software.. I've tried nearly everything.
This is the error:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605VRUFND7_I605VZWFND7_I605VRUFND7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Even at that, if I use sch-i605-16gb for the pit file, I still get nothing
thewhitespicsk8r said:
I was using 4.4.2 before it crashed.... I know I can't go back to 4.1.2 because it's locked, and I can't seem to figure out why it won't let me go back to the stock software.. I've tried nearly everything.
This is the error:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I605VRUFND7_I605VZWFND7_I605VRUFND7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Even at that, if I use sch-i605-16gb for the pit file, I still get nothing
Click to expand...
Click to collapse
When you say that you've tried nearly everything to fix it... hopefully you haven't ODIN flashed any other stock firmware onto the device that was from different phones-- if so, you may have messed up the bootloader. Here's a link to the 4.4.2 firmware if you need it, but I bet you got your file from there already.
You've probably tried this... but you could try flashing just the firmware without the pit file to see if that might work. You could also try to flash them both at the same time to see if that might work.
The most common fixes I've read for ODIN errors are to try other USB ports (the ones on the back of the computer near the power supply seem to be good choices and use a usb 2.0 port), try other USB cables (preferably the original one that came with the phone if it's in good shape), turn off Anti virus programs/ firewalls, make sure you are running ODIN as Administrator. Here's a thread that might provide some other tips for ODIN problems: (GUIDE--Troubleshoot a failed ODIN flash). It's for a different phone, so don't use any of the files linked in the thread...... but the tips provided should be helpful for troubleshooting.
If ODIN version 3.07 isn't working, you could try a newer version of ODIN. Here's some links to other ODIN versions that you might try: Download link for ODIN 3.09 ; Download link for ODIN 3.10.0. ~~With the newer ODIN versions, they have replaced the "PDA" slot with "AP"--so the .tar firmware file goes into AP in the newer ODIN. ****(For reference--Here's the XDA Thread where XDA recognized contributor -CALIBAN666- posted these links to newer ODIN versions. Hit the thanks button for him ****
---------------
If you can't get the restore to work with ODIN, you could always try Samsung Kies to see if it can fix the device...
Where to download Kies -- http://www.samsung.com/us/kies/
Emergency Firmware Recovery using Kies 3 -- http://www.samsung.com/us/support/faq/FAQ00059169/81100
I hope that some of this info helps and that you can get it fixed. Good luck!!