I've searched and searched, but I've been unable to find a solution to, or even any examples of, my particular problem. I was wiping and formatting everything before I flashing a ROM as I've done countless times before, but this time I decided to format the boot partition, which I can't remember ever doing before, and I think I then pulled the battery before flashing anything.
Now when I put the battery back in or plug in the USB cable (without pressing any buttons at all) the phone immediately shows the Vibrant/Samsung screen and nothing else happens. Holding the power button (or power + vol up, or power + vol down, or power + vol up and down) makes the screen flash off momentarily and then come back on again, but that's it. I can't get into recovery mode, and I couldn't get into download mode either, as the phone won't stay off when I put the battery in.
So, I bought a USB jig and to my relief it enabled the phone to get into download mode. I put the jig in the USB port and insert the battery, and download mode immediately comes up. Then I remove the jig and either connect the USB cable and then start Odin, or start Odin and then connect the USB cable. Either way, Odin doesn't recognize the phone. Windows gives me some sort of error about a malfunctioning USB device.
I know the problem is the phone, and not my cable or computer, because I can Odin to my wife's Vibrant no problem. Any ideas?
sporglak said:
I've searched and searched, but I've been unable to find a solution to, or even any examples of, my particular problem. I was wiping and formatting everything before I flashing a ROM as I've done countless times before, but this time I decided to format the boot partition, which I can't remember ever doing before, and I think I then pulled the battery before flashing anything.
Now when I put the battery back in or plug in the USB cable (without pressing any buttons at all) the phone immediately shows the Vibrant/Samsung screen and nothing else happens. Holding the power button (or power + vol up, or power + vol down, or power + vol up and down) makes the screen flash off momentarily and then come back on again, but that's it. I can't get into recovery mode, and I couldn't get into download mode either, as the phone won't stay off when I put the battery in.
So, I bought a USB jig and to my relief it enabled the phone to get into download mode. I put the jig in the USB port and insert the battery, and download mode immediately comes up. Then I remove the jig and either connect the USB cable and then start Odin, or start Odin and then connect the USB cable. Either way, Odin doesn't recognize the phone. Windows gives me some sort of error about a malfunctioning USB device.
I know the problem is the phone, and not my cable or computer, because I can Odin to my wife's Vibrant no problem. Any ideas?
Click to expand...
Click to collapse
Alrighty, well...I actually remember a thread like this coming up awhile back and having no freakin' clue personally...however it lead me to think that you ought to have done a search of the forums before posting this. I was however wrong. I've spent about the last 45 minutes reading thread upon thread upon thread dealing with this issue without any of them offering a solution. Most were simply saying things like:
G0 TRYZZ A KNEW C0RDDD N00BBBIEEE
Click to expand...
Click to collapse
or
1NSTALLZ NEW DRYVRZ U NAP
Click to expand...
Click to collapse
or even
AI0 TO0L BOXXXX S0LVZZ EET 1DIOT
Click to expand...
Click to collapse
Okay...I made that up. Our community isn't so mean lol However, those were pretty much the only solutions I came across, and sadly they did not work.
So....I'm going to take a shot in the dark and suggest you head on over to this thread and give it a whirl:
http://forum.xda-developers.com/showthread.php?p=15330252
I have not seen this suggested in any of the dozens of threads i visited, and honestly, I don't know all too much about the process, but hopefully it will work for you. Read it over, test it out and if it doesn't work head back here and let us know and we can figure something out...and who knows, maybe by then someone with far more knowledge of this particular problem will pass on through and shed some light on the situation.
But for now, concentrate on staying calm and we'll work through it.
Sounds like you deleted the boot loaders. Make sure you have correct drivers installed, windows isn't auto detecting. Try to get Odin to recognize again, try all USB ports. If you get it recognized make sure to √ re-partition.
BTW Xeno, you made me bust out laughing!
sent from my magic box to yours
---------- Post added at 02:53 AM ---------- Previous post was at 02:33 AM ----------
I just read something about this...its not boot loader just boot image. It suggested trying kies.
sent from my magic box to yours
samsgun357 said:
BTW Xeno, you made me bust out laughing!
-----
I just read something about this...its not boot loader just boot image. It suggested trying kies.
Click to expand...
Click to collapse
All in a days work! Aha!
Also, not to go against your advice, because I think its awesome that you responded and are searching for a "cure" but OP do not, I repeat, do NOT touch kies. I'm sure you've heard about the Holocaust in your history classes at some point, yes? Well that was microscopic compared to the disasters that will befall your vibrant if you bring it anywhere near the kies software. Do NOT do it. Think of the kids for God's sake. That is all.
Xenoism said:
Alrighty, well...I actually remember a thread like this coming up awhile back and having no freakin' clue personally...however it lead me to think that you ought to have done a search of the forums before posting this. I was however wrong. I've spent about the last 45 minutes reading thread upon thread upon thread dealing with this issue without any of them offering a solution. Most were simply saying things like:
or
or even
Okay...I made that up. Our community isn't so mean lol However, those were pretty much the only solutions I came across, and sadly they did not work.
So....I'm going to take a shot in the dark and suggest you head on over to this thread and give it a whirl:
http://forum.xda-developers.com/showthread.php?p=15330252
I have not seen this suggested in any of the dozens of threads i visited, and honestly, I don't know all too much about the process, but hopefully it will work for you. Read it over, test it out and if it doesn't work head back here and let us know and we can figure something out...and who knows, maybe by then someone with far more knowledge of this particular problem will pass on through and shed some light on the situation.
But for now, concentrate on staying calm and we'll work through it.
Click to expand...
Click to collapse
"Failed. Unspecified Error." Thanks for the suggestion, though, Xenoism. I knew that no matter how diligent my search of the forums, somebody would toss out a link to a post I missed.
@xeno, your killing me hahaha! I have heard about bad experiences with kies. I have used it a few times without issue, this was my Pre xda days. I figured this guy didn't have much to lose and if kies hard bricked it, he'd have a better shot of Sammy or tmo hooking him up with a fix. I guess for $40 he could get a JTAG repair.
sent from my magic box to yours
sporglak said:
"Failed. Unspecified Error." Thanks for the suggestion, though, Xenoism. I knew that no matter how diligent my search of the forums, somebody would toss out a link to a post I missed.
Click to expand...
Click to collapse
I was afraid that might not help you. I spent another hour or so this morning looking throughout the web for potential solutions...nothing just yet :/
I'll keep searching though, if you do the same man ^^
Related
I was flashing my Vibrant back to the stock ROM using ODIN, and I had the re-partition checked off... and I think this is what killed my vibrant. If I click the power button it doesn't do anything. It has a full battery and even with it on the charger... still nothing. I can't see anything on the screen. What are my options to fix my Vibrant?
Timz917 said:
I was flashing my Vibrant back to the stock ROM using ODIN, and I had the re-partition checked off... and I think this is what killed my vibrant. If I click the power button it doesn't do anything. It has a full battery and even with it on the charger... still nothing. I can't see anything on the screen. What are my options to fix my Vibrant?
Click to expand...
Click to collapse
What were you flashing to stock from?
Can you enter download mode?
Sent from my GT-I9000 using Tapatalk
HELP IM SO WORRY HAS SAME PROBLEM OR WORSE
I upgraded to froyo 2.2 using Kies mini, and follow each step, till it finish of donwloading the oficial download from their server, in the tutorial says to wait for it to reboot but never did. what could happend? now im not able to power on, put in download mode, etc cause its acting like its dead, not even the usb im so scared caus ei just bought it on ebay HELLPPPPP PLEASE.
letor69 said:
HELP IM SO WORRY HAS SAME PROBLEM OR WORSE
I upgraded to froyo 2.2 using Kies mini, and follow each step, till it finish of donwloading the oficial download from their server, in the tutorial says to wait for it to reboot but never did. what could happend? now im not able to power on, put in download mode, etc cause its acting like its dead, not even the usb im so scared caus ei just bought it on ebay HELLPPPPP PLEASE.
Click to expand...
Click to collapse
Following these guide: http://forums.t-mobile.com/t5/Samsu...-upgrade-to-Android-2-2-Froyo-now/td-p/678871
Here are a couple of things to try. There are videos out there on utube also.
http://forum.xda-developers.com/showthread.php?t=954509
http://forum.xda-developers.com/showthread.php?t=819551
No I can't enter Download mode. I have no power at all.
nomadrider123 said:
Here are a couple of things to try. There are videos out there on utube also.
http://forum.xda-developers.com/showthread.php?t=954509
http://forum.xda-developers.com/showthread.php?t=819551
Click to expand...
Click to collapse
Have you tried a simple
pull the battery
put the battery back after a few second
start ODIN
connect USB to PC, but not to phone
hold the volume +/- key
connect USB to phone while holding vol +/- keys
http://www.youtube.com/watch?v=E9LYLoK1Qog
http://www.youtube.com/watch?v=qNts11IBZ8Y
I click the power button nothing happens. I plug in the usb, nothing happens.
Timz917 said:
I click the power button nothing happens. I plug in the usb, nothing happens.
Click to expand...
Click to collapse
Have you tried both at the same time?
pull the battery
put the battery back after a few seconds
start ODIN
connect USB to PC, but not to phone
hold the volume +/- key
connect USB to phone while holding vol +/- keys
nomadrider123 said:
Have you tried both at the same time?
pull the battery
put the battery back after a few seconds
start ODIN
connect USB to PC, but not to phone
hold the volume +/- key
connect USB to phone while holding vol +/- keys
Click to expand...
Click to collapse
SAME AS ME heeeeeeelllpppp
not a single button is working, either JIG i have it, what can i do?
Sorry to disappoint you; it seems that you are out of luck. I was flashing my Vibrant in the similar situation like yours and my phone has never turned on again since then (6 weeks). I live in Thailand and have been searching both English and Thai version for a solution. None comes up so far. The only way the USB jig will help is your phone can be powered up. I have tried that myself. You can look for the confirmation elsewhere in this forum. Any way if you can find a diy solution, please let me know and I will post it here if I can find one myself. Thanks!
http://forum.xda-developers.com/showthread.php?t=848737
I am wait on this line here on your link.
More methods coming soon
do you have insurance with tmobile?
i bricked mine before i had a good understanding of the whole rom flashing concept and i could get a downloading screen but i didnt know what to do so they replaced it with no problem.
call and ask all they can do is say no.
nomadrider123 said:
http://forum.xda-developers.com/showthread.php?t=848737
Click to expand...
Click to collapse
they bro, i appreciate that your trying to help the guy but read.
the title states its a "HARD BRICK" meaning it will not turn on. If the OP has enough sense to name the thread its a HARD brick, then i'm sure he knows what a hard brick is. All solutions your leading to cannot be done AT ALL. The phone is a paperweight, you cant do anything but 2 things:
@OP
Do one of these 2 things:
1) build a JIG costs around 10$ a bit more or a bit less. but no over than 15$
(search JIG for vibrant on youtube by mobiletechvideos)
2) Send it to tmobile.
I hard bricked my phone 4 days ago.
I called them, and their sending in a replacement, and i send them mine and im done.
It cost me 10$ for shipping and handling but thats it.
Timz917 said:
I was flashing my Vibrant back to the stock ROM using ODIN, and I had the re-partition checked off... and I think this is what killed my vibrant. If I click the power button it doesn't do anything. It has a full battery and even with it on the charger... still nothing. I can't see anything on the screen. What are my options to fix my Vibrant?
Click to expand...
Click to collapse
HOW ABOIUT LEAVE PHONE CHARGING FOR 10 GO IN TO DARK ROOM SHUT OFF LIGHT PRESS POWER BUTTON AND SEE IF BACK LIGHT OF SCREEN LIGHTS UP, IF SO I TOLD YOU SO I HAD THE SAME BUT MY VIBRANT WORKS AGAIN UNLIKE YOURS p
xriderx66 said:
they bro, i appreciate that your trying to help the guy but read.
the title states its a "HARD BRICK" meaning it will not turn on. If the OP has enough sense to name the thread its a HARD brick, then i'm sure he knows what a hard brick is. All solutions your leading to cannot be done AT ALL. The phone is a paperweight, you cant do anything but 2 things:
@OP
Do one of these 2 things:
1) build a JIG costs around 10$ a bit more or a bit less. but no over than 15$
(search JIG for vibrant on youtube by mobiletechvideos)
2) Send it to tmobile.
I hard bricked my phone 4 days ago.
I called them, and their sending in a replacement, and i send them mine and im done.
It cost me 10$ for shipping and handling but thats it.
Click to expand...
Click to collapse
Your first option is out because I have tried that. The only option left is the second one. since I live in Thailand, I have to ship the phone to my friend in Los Angeles to have him replace it for me. It is costly, but at least I will get a phone to work.
It seems to me that this issue is a special case that doesn't happen very often. Only the chosen ones will get into trouble like this when making an error here and there while flashing rom.
I had an IPhone 3G before and, of course, I made mistakes while updating it with all kinds of firmware, but the hardware never fails on me no matter what I did.
Thanks all who try to help.
xriderx66 said:
they bro, i appreciate that your trying to help the guy but read.
the title states its a "HARD BRICK" meaning it will not turn on. If the OP has enough sense to name the thread its a HARD brick, then i'm sure he knows what a hard brick is. All solutions your leading to cannot be done AT ALL. The phone is a paperweight, you cant do anything but 2 things:
@OP
Do one of these 2 things:
1) build a JIG costs around 10$ a bit more or a bit less. but no over than 15$
(search JIG for vibrant on youtube by mobiletechvideos)
2) Send it to tmobile.
I hard bricked my phone 4 days ago.
I called them, and their sending in a replacement, and i send them mine and im done.
It cost me 10$ for shipping and handling but thats it.
Click to expand...
Click to collapse
Just because he put hard bricked in the title means little. It was his first post. He very well could be a aviid user. All I could go by is he said he hit power and nothing happend thats about all he said over and over. No battery pull 3 button try. So what I did was try to help thats it. I did not suggest anything to make matters worse. A lot of ppl thought their phones were "hard bricked" but they got it to come out of it. Just because your more of a wiz then most ppl here. I would appreciate if you would get off my back a bit for I was just trying to help.
nomadrider123 said:
Just because he put hard bricked in the title means little. It was his first post. He very well could be a aviid user. All I could go by is he said he hit power and nothing happend thats about all he said over and over. No battery pull 3 button try. So what I did was try to help thats it. I did not suggest anything to make matters worse. A lot of ppl thought their phones were "hard bricked" but they got it to come out of it. Just because your more of a wiz then most ppl here. I would appreciate if you would get off my back a bit for I was just trying to help.
Click to expand...
Click to collapse
I'm not getting on your back, why is it you think so?
Most of the users as i've encountered don't have the sense to name their threads appropriately, the OP on this one specifically named it HARD BRICKED, so instead of telling him to do all these instructions, you could've asked 1 thing "when you plug your usb, or wall charger, does it show any lights? or Are there any symbols on the screen? any lights glowing?"
Those 2 questions could've saved him, and you time.
Trust me i'm a beginner as well, i just know how to get out of these because i've been with this problem a few times. Alot of people here know more than me, specifically s15.. idk his full name.
call me a noob, but i thought that Odin was taking too long (45 mins)(tried to switch from CM7 to stock firmware) and was stuck, so i closed out and turned off my phone by taking out the battery (idiot, i know) and now my phone wont turn on, and ive tried taking out the battery, pressing a number of button combos, and the people at radioshack didnt help (big suprise). any ideas?
Try holding the power button alone, for like 15 or more seconds.
Not sure beyond that....
didnt help...what i think the problem is that i dont have a firmware on my phone to boot it from...
You need enter download mode. It's not clear from your post if you tried to enter download mode or not. Can you get into download mode? Do you have a jig?
Btw, 45 minutes was definitely too long for Odin, so there probably wasn't any thing else you could have done.
no, i cannot get into download mode, and i do not have a jig. would that fix the problem completely?
Unsure - seems like somehow you killed your bootloader, not sure how since no return-to-stock package has bootloaders.
You should be able to get into download mode by this method: With the phone powered off, plug in the usb cable while holding the vol up + vol down buttons (but not the power button). When the warning screen appears, press Volume up to continue into download mode.
The jig is just another way to get into download mode, and certainly worth a try if you have one or can borrow one. With the phone powered off, plug in the jig, and the phone will immediately go into download mode.
You must have enough charge on the battery for the phone to turn on.
If the battery has charge, and you are unable to get into download mode by any method, and if you are unable to get any signs of life from your phone in any way, then as Entropy said, you may have damaged bootloaders.
The only way to damage one of the bootloaders, as far as I know, is for Odin to be interrupted while it is flashing the bootloader. So this begs the question, what exactly were you trying to flash that didn't complete in 45 minutes?
If your phone is truely hard bricked, the only way to recover it is to send it to a professional like connexion2005 of Mobile Tech Videos who can use jtag to reset the bootloaders.
Oh oh, I feel bad for the OP.
People keep saying this device is "unbrickable" but apparently not.
votinh said:
Oh oh, I feel bad for the OP.
People keep saying this device is "unbrickable" but apparently not.
Click to expand...
Click to collapse
He should be able to clear it with a jig, but no one can guarantee that this will work. I have seen it fix this issue before though.
votinh said:
Oh oh, I feel bad for the OP.
People keep saying this device is "unbrickable" but apparently not.
Click to expand...
Click to collapse
No one claims it's unbrickable - just that it's damned hard to brick.
I'm still curious what he was trying to flash - I have NEVER heard of anyone hardbricking their devices unless:
1) They screwed with bootloaders - which is why I have included gigantic red warnings with anything I post that includes a bootloader
2) They flashed something not intended for the device
Iskor12 said:
He should be able to clear it with a jig, but no one can guarantee that this will work. I have seen it fix this issue before though.
Click to expand...
Click to collapse
If the bootloader somehow got corrupted (like crawly and Entrophy mentioned) then a jig won't do any good, I think.
It's good that some guru can access and reprogram the bootloader via JTAG.
I keep fingers crossed for OP.
---------- Post added at 09:54 PM ---------- Previous post was at 09:44 PM ----------
Entropy512 said:
No one claims it's unbrickable - just that it's damned hard to brick.
I'm still curious what he was trying to flash - I have NEVER heard of anyone hardbricking their devices unless:
1) They screwed with bootloaders - which is why I have included gigantic red warnings with anything I post that includes a bootloader
2) They flashed something not intended for the device
Click to expand...
Click to collapse
Experienced people can avoid those fundamental mistakes but newbies often get hair pulling, head scratching before mumbling "dang, why would I do that in first place"
Entropy512 said:
No one claims it's unbrickable - just that it's damned hard to brick.
I'm still curious what he was trying to flash - I have NEVER heard of anyone hardbricking their devices unless:
1) They screwed with bootloaders - which is why I have included gigantic red warnings with anything I post that includes a bootloader
2) They flashed something not intended for the device
Click to expand...
Click to collapse
Personal experience here. Flashed a one click for a captivate and bricked it a year ago. Went through everything, reported a success, and even sent reboot command to phone when it was done. 'Rebooted' to a black screen. For the better part of a week I tried everything, and I mean everything. Just unbricked last night/this morning with the 'unbrickable mod'. Wow micro soldering.
What led up to this was flashing a friends captivate with another one click odin package. Bricked it too (really need to quit doing that) but I think a usb jig might have worked on that one, but didn't have one with me. After doing the unbrickable mod to the phone that sat for over a year, I flashed it with the same package that just bricked the second captivate, and it worked fine. I did nothing different. I'm very patient in doing things the right way. Same steps, same software, same computer, no brick.
Sent from my páhhōniē
To the OP
Is getting Samsung Tech support an option, if everything else fails, then you dont have anything to lose, they support by phone and was pleseantly suprised with their help.
AdamOutler is willing to work on bringing the unbrickable mod to the i777. All he needs is an i777, bricked or not. If anyone has one that is bricked, by all means send it to him. He said not only will he
unbrick it using jtag, he'll attempt to do the unbrickable mod to it.
I'd be willing to donate to him and anybody who helps make it possible by sending him their phone.
Sent from my páhhōniē
I bricked my galaxy note i717 beyond recovery with a regular jig. I've looked into jtag but I haven't found any information whether it's viable for the i717 (i.e. which jtag it's using, which box I would need, where I would need to bring it etc etc.)
So here's my question: Do any of you guys know any more about how to unbrick the phone or details about whether/how to unbrick using jtag?
Maybe I've overlooked something else. Here's how it went down:
I was stupid and tried to flash the phone with firmware for the N7000 because I was overexcited and didn't know that it wasn't an n7000. Now the recovery mode wouldn't let me upgrade (understandable reasons I guess) so I decided to force flash it with odin which also didn't let me upgrade the phone. So I used some method relying on adb. The process took way to long so I unplugged the phone mid-way through it, then replugged it and suddenly the process reported success. So the phone started rebooting just that instead of actually booting up it stayed black. Pressing any of the buttons yields no response - neither vibration nor any screen response. Using the usb jig also yields no response but I'm not entirely sure if there's a jig method that might work - or a key combo that might work - or even a usb method that might work.
Anyway any advice would be highly appreciated.
Did you try return to the store where you boought it? If your phone don't show anything on the screen, there is no way store knows what's going on with your phone unless you tell them the truth
That's exactly what I would do
Sent from my SAMSUNG-SGH-I717 using XDA App
if you can get into download mode try reflashing the stock recovery found in the dev section then if you can get that fair try flashing the odin stock rom to see if it will boot
Read his OP. He can't get into the download mode even with a Jig.
I have yet to encounter any one as reckless as OP trying so hard to brick the phone
foxbat121 said:
Read his OP. He can't get into the download mode even with a Jig.
I have yet to encounter any one as reckless as OP trying so hard to brick the phone
Click to expand...
Click to collapse
he never said if he tried with the hardware buttons doesn't mean he cant do it if hes been trying the jig
foxbat121 said:
Read his OP. He can't get into the download mode even with a Jig.
I have yet to encounter any one as reckless as OP trying so hard to brick the phone
Click to expand...
Click to collapse
Somebody has to be the guinea pig I guess lol. Glad it wasnt me. LOL Only thing worse is the Will it blend guy or the iFix it tear downs lol.
BLOWNCO said:
he never said if he tried with the hardware buttons doesn't mean he cant do it if hes been trying the jig
Click to expand...
Click to collapse
If jig won't work, I'm pretty sure hardware button won't work either. It goes without saying that he probably already tried everything he could find.
edpsx said:
Somebody has to be the guinea pig I guess lol. Glad it wasnt me. LOL Only thing worse is the Will it blend guy or the iFix it tear downs lol.
Click to expand...
Click to collapse
That's not guinea pig. He did couple wrong things in a row (wrong ROM, god know what he is doing with abd and then unplug the phone in the middle of flashing or something). If I'd make a guess, he screwed up the bootloader.
foxbat121 said:
Did you try return to the store where you boought it? If your phone don't show anything on the screen, there is no way store knows what's going on with your phone unless you tell them the truth
Click to expand...
Click to collapse
Yeah I thought about doing that - worst case scenario they tell me I voided my warranty and give me the phone back and I can still try finding a jtag solution or do i have to face any other consequences including maybe never getting my phone back?
foxbat121 said:
He did couple wrong things in a row (wrong ROM, god know what he is doing with abd and then unplug the phone in the middle of flashing or something). If I'd make a guess, he screwed up the bootloader.
Click to expand...
Click to collapse
That's my guess too. I screwed up badly. I would like to blame it on the late hour I did all that but it was just overexcited stupidity -_-
Try your buttons...
Everybody's talking about whether you tried to get into download mode with buttons, but You have not said for sure you tried it.
Hold down down volume button, home button and power button all at the same time. You don't know for sure until you try it.
brojoe11 said:
Everybody's talking about whether you tried to get into download mode with buttons, but You have not said for sure you tried it.
Hold down down volume button, home button and power button all at the same time. You don't know for sure until you try it.
Click to expand...
Click to collapse
I'm sorry that I wasn't being very clear on this but I have tried and it didn't work. Thanks though.
cilmeron said:
I'm sorry that I wasn't being very clear on this but I have tried and it didn't work. Thanks though.
Click to expand...
Click to collapse
I know on some phones that download mode can still be activated even if the screen isn't working properly and displaying it. I know many infuse users ran into problems and were still able to use Odin to flash stock and fix their phone. Try doing the hardware method of getting into download mode, and even though your screen doesn't show anything, it may still connect to Odin and you could try to flash back to stock.
Sent from my SGH-I997 using xda premium
U cant brick these phones.use the hardware buttons to get into download mode.
Take battery out and put it back in.hold power vol down and home for 20sec and then press vol up and plug into ur pc with odin running.u should see something on port section.
If that dont work.hold power and both vol. Buttons for 30 sec. Then press vol.up and plug in usb.hope it works.
mintu123 said:
U cant brick these phones.use the hardware buttons to get into download mode.
Take battery out and put it back in.hold power vol down and home for 20sec and then press vol up and plug into ur pc with odin running.u should see something on port section.
If that dont work.hold power and both vol. Buttons for 30 sec. Then press vol.up and plug in usb.hope it works.
Click to expand...
Click to collapse
Actually, you can brick it to the point of needing JTAG repairs to restore your device. That being said, it's very very very hard to brick it. You have to do something like flash firmware for a completely wrong device and screw up your bootloaders in the process.
cilmeron said:
I bricked my galaxy note i717 beyond recovery with a regular jig. I've looked into jtag but I haven't found any information whether it's viable for the i717 (i.e. which jtag it's using, which box I would need, where I would need to bring it etc etc.)
So here's my question: Do any of you guys know any more about how to unbrick the phone or details about whether/how to unbrick using jtag?
Maybe I've overlooked something else. Here's how it went down:
I was stupid and tried to flash the phone with firmware for the N7000 because I was overexcited and didn't know that it wasn't an n7000. Now the recovery mode wouldn't let me upgrade (understandable reasons I guess) so I decided to force flash it with odin which also didn't let me upgrade the phone. So I used some method relying on adb. The process took way to long so I unplugged the phone mid-way through it, then replugged it and suddenly the process reported success. So the phone started rebooting just that instead of actually booting up it stayed black. Pressing any of the buttons yields no response - neither vibration nor any screen response. Using the usb jig also yields no response but I'm not entirely sure if there's a jig method that might work - or a key combo that might work - or even a usb method that might work.
Anyway any advice would be highly appreciated.
Click to expand...
Click to collapse
I've read some so my suggestion is this:
First make sure that you have the drivers installed for your phone. Then pull the battery wait for a few seconds. press the down button and then the power to go in download mode and hold them pressed for 20s. Now plug in the USB and press the volume up button. If Odin detects it you're good to go! If not... Well it's worth a shot
My theory is that even though the screen is blank, the hardware still boots properly. Just make sure your battery is somewhat charged. And also plug in the USB AFTER you "boot" in download mode.
Sent from my SGH-I717R using xda premium
I was stupid and tried to flash the phone with firmware for the N7000 because I was overexcited and didn't know that it wasn't an n7000. Now the recovery mode wouldn't let me upgrade (understandable reasons I guess) so I decided to force flash it with odin which also didn't let me upgrade the phone. So I used some method relying on adb. The process took way to long so I unplugged the phone mid-way through it, then replugged it and suddenly the process reported success. So the phone started rebooting just that instead of actually booting up it stayed black. Pressing any of the buttons yields no response - neither vibration nor any screen response. Using the usb jig also yields no response but I'm not entirely sure if there's a jig method that might work - or a key combo that might work - or even a usb method that might work.
Click to expand...
Click to collapse
Everything here screams 'you should never attempt to modify your device again.'
What is it with all you smart asses telling him he shouldn't have done it??? What, you never made a mistake in your entire life???
Sent from my SAMSUNG-SGH-I717 using XDA App
Why don't you find Adam_Outler in the hardware hacking forum? Send your phone to him and he'll hopefully be able to create an unbrickable mod. Not only will you likely have a fixed phone but it will mean volumes for our community.
Note, you will be without a phone for a bit
I did something stupid to my note too so don't feel too bad. **** happens... I returned my note to att with no problem because my screen was permanently black. Wouldn't do anything download mode,cwm nothin.. Flashed gsm kernel from root so beware the way its layed out u won't know its gsm unless you read it extremely careful. I had read the thread three times and only caught it after i read really slowly post-brick.
Sent from my SAMSUNG-SGH-I717 using XDA
ekerbuddyeker said:
What is it with all you smart asses telling him he shouldn't have done it??? What, you never made a mistake in your entire life???
Sent from my SAMSUNG-SGH-I717 using XDA App
Click to expand...
Click to collapse
It's not that, we've all made mistakes, but it's like this guy went out of his way to try to brick the phone. This isn't like "oh crap, I flashed the wrong radio"
He tried to flash a ROM from a different SoC and every fail-safe wouldn't let him do it. I'm surprised at how well the different programs tried to save his phone, then he actually went ADB and forced it onto his phone and then he unplugs during a flash.
It's like he drove his car without paying attention and hit a fence that prevents you from flying off a cliff, then he kept ramming his car into the fence, then took some C4, blew up the fence, drove off the cliff, then started yelling "help, I fell off the cliff"
N3RD420 said:
I did something stupid to my note too so don't feel too bad. **** happens... I returned my note to att with no problem because my screen was permanently black. Wouldn't do anything download mode,cwm nothin.. Flashed gsm kernel from root so beware the way its layed out u won't know its gsm unless you read it extremely careful. I had read the thread three times and only caught it after i read really slowly post-brick.
Sent from my SAMSUNG-SGH-I717 using XDA
Click to expand...
Click to collapse
I'm confused, is there a CDMA Note? What do you mean "they won't know it's GSM"?
-----------------
---This first post is outdated. My current question is one post below. I've left the content of this post for other noobs to see.
-----------------
Hey folks, sorry to bother you all but all input would be greatly appreciated. I'm rather unfamiliar with android flashing and kernels, and have spent the last 8 hours trying to figure this out to no avail.
Following this (http://forum.xda-developers.com/showthread.php?t=1238070) (section 5) guide on how to get back to stock gingerbread on my phone (after a few partially failed attempts flashing other roms), I was using Odin, had the .pit 2.2 as well as CI500_VZW_EH03_GB_CM.tar.md5 loaded into the program and left it running. About 20 mins in, the phone stopped progressing and I started to get concerned. After two hours, I powered down the phone and proceeded to reattempt the flash. This is when things got weird. My phone was unable to enter the Download Mode and instead showed Android system recovery when plugged in, or a black screen with a phone and a computer, with arrows between when not plugged in. The weirdest part is that the phone no longer recognized vol+ or the power button when in Android Recovery, and could only vol- to go down the menu, then was stuck at the bottom of the list.
I've searched everywhere on this site, and google to try and come up with a solution.
When pluggin into the computer, I hear a connection sound, but the device is not recognized by Odin. Pressing the running a blind vol+ and vol-, then a vol- to hope Odin recognizes the device, as pointed out in this (http://forum.xda-developers.com/showthread.php?t=1764022) thread, resulted in nothing. Holding vol- while pluggin in the usb cable, doesn't show the download mode. All of the steps in this (http://forum.xda-developers.com/showthread.php?t=1026746) thread proved futile, as most of them required download mode anyways.
I'm going to keep searching and keep you posted as things come. Your help as always will be greatly appreciated!
Edit: Things just got weirder... After a few more attempts at making this work, I'm now getting an "Unable to charge non-supported battery. See user manual." With this error, I'm not able to get into Android Recovery anymore. More searching...
Edit 2: AFAIK I'm gonna need a jig. Anyone confirm?
Edit 3: Got a jig, Download Mode working, all is well. Please remove this thread, or leave it for other noob flashers to see.
Hey Folks, its been a while since I last posted in this forum, but I ran into a pretty serious issue earlier this evening. I was attempting to flash CM9 to my T959D and was running into tonnes of trouble. Throughout my attempts I was restoring back to stock rom, kernel and bootloader. During one of these restores, Odin froze in Win 7. Since then I've been unable to detect any form of life from the phone. It simply sits in a black screen. Holding the vol down while booting, blind vol up and down cable inserting, using my Jig and inserting the cable/battery in various orders results in nothing. The most I hear is a device failure to connect sound in Windows with no sign of life in Odin.
What can I do?
Someone posted stating leaving the battery out for multiple days would reset something on the motherboard, allowing me to get into download mode. Though I was hoping to have this resolved tonight. I realize that there aren't many people left with these phones, but I hope someone has a solution to this.
I'm going to be installing ubuntu tonight on an older desktop in a effort to resolve this. Though my experience with it is very limited, and success is unknown.
NOT GOOD... You should wait and see if others have a better solution, but Unbrickable Mod may be your only option.
Posted from my Fascinate using XDA Premium
MultipleMonomials said:
NOT GOOD... You should wait and see if others have a better solution, but Unbrickable Mod may be your only option.
Posted from my Fascinate using XDA Premium
Click to expand...
Click to collapse
Thats not good to hear. Well, I was snooping around looking for someone who could solder this for me, to no avail. My soldering skills are non existent. The most I fixed was a door bell, and I did a terrible job. I won't be able to get my hands on a soldering iron until tomorrow, is it worth trying?
I have located someone who can do a jtag on this model but have a few questions in regards to this:
Since my bootloader was corrupted, would the jtag service put a new bootloader on?
Would it prevent the same thing from happening again?
Are jtags designed on a per-phone basis?
Since there is a telus fascinate T959D as well as a verizon fascinate, and both phones are completely different, would I need to make sure the jtag is meant for this phone?
Is there anything I need to be made aware of before doing this that I haven't mentioned?
I've haven't had any experience with JTAG, but I've heard Unbrickable Mod is preferable. If you're looking for someone who can solder, check out your local RC/hobby store. If that fails, check out an electronics store, though it may take some searching to find one.
Posted from my Galaxy Tab with CM10
TheMegosh said:
Thats not good to hear. Well, I was snooping around looking for someone who could solder this for me, to no avail. My soldering skills are non existent. The most I fixed was a door bell, and I did a terrible job. I won't be able to get my hands on a soldering iron until tomorrow, is it worth trying?
I have located someone who can do a jtag on this model but have a few questions in regards to this:
Since my bootloader was corrupted, would the jtag service put a new bootloader on?
Would it prevent the same thing from happening again?
Are jtags designed on a per-phone basis?
Since there is a telus fascinate T959D as well as a verizon fascinate, and both phones are completely different, would I need to make sure the jtag is meant for this phone?
Is there anything I need to be made aware of before doing this that I haven't mentioned?
Click to expand...
Click to collapse
Make sure you use the stock Samsung cable see if you can reinstall the drivers hook it into the computer and hold volume down if you can get any type of signal from the phone your good.
Sent from my SCH-I500 using Tapatalk 2
---------- Post added at 04:27 PM ---------- Previous post was at 04:24 PM ----------
MultipleMonomials said:
I've haven't had any experience with JTAG, but I've heard Unbrickable Mod is preferable. If you're looking for someone who can solder, check out your local RC/hobby store. If that fails, check out an electronics store, though it may take some searching to find one.
Posted from my Galaxy Tab with CM10
Click to expand...
Click to collapse
Hey no offence but stop telling everyone on the street they need too soljeir there phone with unbrickable mod before they can fix I'm tired of having too calm the person down after you said they have too open up the phone its utter bull****. 1 out of 10 soft bricks you may need it I've been without download mode and fixed mine just fine.
Sent from my SCH-I500 using Tapatalk 2
An update:
Took my phone in to get the jtag service... He said some of my partitions were corrupted, one of which was the boot layer. He put a new bootloader on, and showed it could be placed back into recovery and download mode, but when I got home the device was even more dead than when I left; no device failed to connect sound in windows, just nothing. I'm taking it back to him in a week after exams to get this resolved. Maybe the battery has reached the end of its life...? I checked it with a volt meter, and it had 3v+ so I really don't know.
Sent using Science!
As bbrad pointed out, there may be other solutions, and my answer could be totally wrong, but if even your bootloader is cooked, Unbrickable Mod may be your only hope. Since UM affects startup code literally hardwired into the chip, it should work as long as the JTAG doesn't interfere.
Posted from my Fascinate using XDA Premium
Another update. So apparently I flashed a bootloader from another phone, which royally screwed up the partition, kernel and mounted drives. The technician managed to get the original bootloader, kernel and rom on the phone and everything is working from stock again.
Why on earth is the 959d Telus version such a pain in the ass to customize?
Is there anyone on here that uses a 959d that can direct me to a proper method to leaving stock? Before this entire situation I had vodoo kernel on, with cwm, but every time I flashed a kernel it would hang on reboot and either sit on a black or white screen. In a lot of cases I would flash in cwm, reboot, then I would be brought back to cwm as if there was no rom on the phone at all, no matter what I formatted and wiped.
When I'm not on my phone I can link all of the guides I've tried that leave me back where I started. So I re flash back to stock using Odin.
At the end of the day, I have to ask, is it really worth it in the end? I've rooted and flashed many roms on other phones but have never run into as many problems as with this fascinate t959d
Sent using Science!
Alright. let us get this straight. I have searched in countless number of forums for solving my issue but I'm NOT able to fix it.
I have a Samsung Galaxy S Vibrant T959. It currently seems to be "soft-bricked" (I always see a mobile connected to a computer and an exclamation icon in between). So to reset it, I have left almost not stone unturned. But no luck so far
As far as I remember, I happened to land it in trouble while I was trying to flash some secondary bootloader using ODIN.
I also tried the micro-USB JIG method by building a 300k-Ohm USB JIG on my own (using three 100k-Ohm resistors), but even that is not working for me. Whenever I connect my phone to my computer, it starts up and shows those three icons. The same happens when I remove the battery, insert it back and start the phone up again. The same happens for each of the numerous key sequences mentioned online for download/recovery mode. So literally NOTHING is working for me. I also tried OneClick.jar, Heimdall. None of them are making me lucky as the phone is not getting detected.
I believe there has to be a way to reset it somehow (although I seem to have screwed something seriously) but nothing seems to work for me. What can I possibly do now?
Attached images show the micro-USB jig that I made and the icon on my phone I see.
From my experience if you can get that far you don't need a jtag. But you did say that you flash bootloader. So you ether need to get the right combo to get to download mode or you are done with out working bootloader. The only other thing that I can think of would be to do the unbrickable mod.
Sent from my Nexus 4
Thanks jrongi1 for the reply.
>> So you ether need to get the right combo to get to download mode or you are done with out working bootloader.
I have tried many, many combos for getting the download mode but no luck so far Can you suggest some if you are aware of one?
The only other thing that I can think of would be to do the unbrickable mod.
>> I tried to know about this but I did not understand what this exactly means? I believe this involves some sort of hardware rework. Can you please point me to steps to do this? Are you referring to this procedure? If yes, I don't believe it's a solution since that procedure is just a preventive measure and not a solution (that's what I understand after reading that whole thing out).
Try that.
reboot computer, turn off phone, take out battery, put the battery back, hold volume up and down buttons and then plug in usb.
Sent from my SGH-T959 using xda app-developers app
This is from N00B_IN_N33D's MIUI guide stickied at the top.
"SOFT" BRICKED WHILE USING ODIN?
If you are getting a "Phone.. ! ..Computer" image (seen above) when booting phone, yes, you are bricked but it is reversible! Just follow these steps...
Make sure you have ODIN OPEN with admin privileges!
1.) Take off your back cover, remove your sim & mirco sd card.
2.) Remove your battery.
Make sure you have the USB plugged into your PC but NOT your phone!
3.) Hold the volume buttons.
4.) Put the battery in.
5.) Put the USB in.
You don't necessarily need the download mode image to be present. As long as you are getting the COM ID to light up yellow in ODIN, just flash back to stock like normal.
Click to expand...
Click to collapse
Sometimes the key combo can be a bit precarious and the timing needs to be precise. I know that when I have taken my Vibes back to stock, it takes me more than a few tries to get it right. You've said you have tried the key combos several time, I think you should keep trying them and get your timing right. I would hate for you to screw up your phone when doing the Unbrickable hardware mod, when it could be something as simple as a timing thing.
As the other guys said work with the buttons and only try the unbrickable mod as a last resort.
Sent from my Nexus 4
Thanks guys for responses.
testomat/Woody, I tried as per your steps almost 8-10 times, but that does not work either
jrongi1,
I do not wish to go for Unbrickable mod either. Anyway, I have contacted a local repairs guy for this issue. He said he can fix this issue using JTAG interface. That costs me 1500INR. That's the only solution I have I guess.
Good luck with the repair I hope that you can get going soon.
Sent from my Nexus 4
Thank you so much again!
Woody said:
This is from N00B_IN_N33D's MIUI guide stickied at the top.
Sometimes the key combo can be a bit precarious and the timing needs to be precise. I know that when I have taken my Vibes back to stock, it takes me more than a few tries to get it right. You've said you have tried the key combos several time, I think you should keep trying them and get your timing right. I would hate for you to screw up your phone when doing the Unbrickable hardware mod, when it could be something as simple as a timing thing.
Click to expand...
Click to collapse
This worked for me.....Many thanks