CM10 cuts out streaming audio over wifi after about 10 min. - Sprint HTC EVO 4G LTE

I had this problem with my stock evo, I had to go into advanced wifi settings, and there was a check box labeled "best wifi performance, may consume more battery". After checking that, I never had a problem. I now have CM10 and I have the issue again, however there is no settings that seem to work. Does anyone know anything about this?
If it matters, I am streaming a line in with VLC over our local network to Vplayer. Works fine on original Evo 4g, and a stock 4g LTE.

I would say play with cache settings. A few apps have a cache setting that's too low.

om4 said:
I would say play with cache settings. A few apps have a cache setting that's too low.
Click to expand...
Click to collapse
tried setting buffer size, no go. I've tried 3 different apps to keep wifi connected, but didn't work. I just searched again and found wifi stay alive, and so far so good, but it's only been 15 minutes, too early to tell. Either way, wish there was the setting available in CM10.

Well that didn't last long, it just cut out.

Did you check to see that WiFi is set to stay on when screen is off. If you tap on WiFi it goes into settings

om4 said:
Did you check to see that WiFi is set to stay on when screen is off. If you tap on WiFi it goes into settings
Click to expand...
Click to collapse
Yes, 1st thing I checked. That is when I noticed that there is not a "best wifi performance" option, which fixed the problem on the stock 4g LTE for me.

Odd. If I can think of anything I'll let you know. Now this is just streaming through vlc? Or streaming over your network in general?

om4 said:
Odd. If I can think of anything I'll let you know. Now this is just streaming through vlc? Or streaming over your network in general?
Click to expand...
Click to collapse
Thanks. Through vlc ( I listen to a morning show at work), but also happens streaming any media file over the network as well. I know it has something to do w/ the "best wifi performance" option because before I flashed this ROM, it worked, but now no "best wifi performance" option.

Well it can also be network latency. Best performance minimizes latency. Try adjusting the streaming setting on vlc

Have you tried changing channels with your router? Use the app WiFi analyzer and it will tell u the best channel to avoid interference.
It sounds stupid and amateurish, but I know a few people it worked for. Does your WiFi disconnect and connect to 3g then back over and over too? Have u installed new radios?
Ask me about my ability to annoy complete strangers!

Not the router for sure. I did dig up a lot of talk on a hidden power settings menu. Seems like after one of the updates from htc/sprint added the "best wifi performance" may toggle some of those settings, as people were pulling up that menu and unchecking some things and fixed their wifi disconnect problems. CM10 does not have that shortcut/menu anywhere though. ugh. I'm so frustrated. I'd hate to revert my phone back to stock, but this is the only issue I have right now.

Not stupid or amateurish at all, wish I thought of it, its actually a very good suggestion

I can't believe I forgot to mention this only happens when the screen is off. I can leave the screen on and it doesn't cut out, but it kills the battery, and I'm accidently making things happen constantly. I should note that I've tried every setting I could find, and also tried a good handful of apps that are supposed to keep wifi alive, but it still happens. Any other suggestions?

Well, after a handful of jellybean Roms, Codename Android, based off of Clean Android 4.1.1 Rev6 (JRO03R) is the only one that works! My signal remains strong and does not disconnect when the screen is off.

As a last resort
Hey man, if any of these things don't seem to help, try a custom kernel. Komodo rls. 7 works great. I have been helping him out and it is a great kernel. Many options and lots of governors. May help your wifi.
Here is what I suggest:
Check on another wifi signal (make sure it isn't your router)
Update radios
Do suggestions above
Load Komodo kernel
Reflash everything after a clean wipe
And as a last resort beg a dev to port that option over.

Related

[Q] cyanogenmod 7 wifi issues

I recently flashed on cm7 on my aria. it is great but my data usage began shooting up. i realized it was due to the fact that everytime i lock my phone, it disables my wifi (i saw this because everytime i unlock im on 3g for a 1-2 seconds then i get on wifi so that means that the whole time my phone is locked it uses 3g data ) is there anyway i can prevent this from occurring??
Thanks,
Okachowwa
Menu -> settings -> wireless & networks -> wi-fi settings -> menu -> advanced -> wi-fi sleep policy -> never
I think that's it.
Sent from my Aria - CM7 Build 24
okachowwa said:
I recently flashed on cm7 on my aria. it is great but my data usage began shooting up. i realized it was due to the fact that everytime i lock my phone, it disables my wifi (i saw this because everytime i unlock im on 3g for a 1-2 seconds then i get on wifi so that means that the whole time my phone is locked it uses 3g data ) is there anyway i can prevent this from occurring??
Thanks,
Okachowwa
Click to expand...
Click to collapse
Have you checked the Wifi Settings to see which sleep option is selected? There is an 'Never' option which tells wifi to stay on even when the phone sleeps.
One thing I noticed its that if I leave my house I have to turn off wifi and turn it back on to find my router.
Sent from my Liberty using XDA App
klbmth said:
One thing I noticed its that if I leave my house I have to turn off wifi and turn it back on to find my router.
Sent from my Liberty using XDA App
Click to expand...
Click to collapse
yup...that's why you just turn your wifi off with the notification widget (very simple and painless might I add) if you know you're leaving the house...what's the point of having wifi enabled if you're not in range of your network? all it's going to do is drain your battery. i left my wifi enabled one day when i sent to work and within half the day i had ~12% battery life...definitely not good practice to leave it enabled that's my 2 cents, do as you wish though. to each his own.
klbmth said:
One thing I noticed its that if I leave my house I have to turn off wifi and turn it back on to find my router.
Sent from my Liberty using XDA App
Click to expand...
Click to collapse
Yup, I have the same issue with CM7 nightlies. This worked flawlessly in CM6 and stock2.1. So far there isn't a viable solution.
from the CM6.1.1 thread...
Q. How do I keep my wifi from going to sleep every time the screen shuts off?
A. There is a hidden feature that disables wifi sleep.
menu > Settings > Wireless & networks > wifi settings > menu (again) > advanced > Wi-Fi Sleep policy > Never > menu > Save
However: although you can keep the wifi service from sleeping, the wifi driver will still sleep on it's own after detecting no bus activity for a period of time.
Click to expand...
Click to collapse
mattbollenbach said:
from the CM6.1.1 thread...
Click to expand...
Click to collapse
I've made sure to set Wifi Sleep Policy to "Never" but that did not fix my wifi problems. What I see when I open Wifi Settings is a cycle of:
Code:
Scanning --> Connecting --> Disconnected... Scanning, etc
When I look in logcat it shows it attemping (in vain) to authenticate against the last wifi network I was using -- even though it is no longer in range (and clear across town). In a nutshell it is refusing to recognize the actual nearby network UNTIL I toggle wifi settings.
I've had the same behavior on FR008 and the stock ATT 2.1 load as well. When Wifi is in that on but not really connected state some apps can wake it up...the default browser usually will, but Listen would not. I just gave up and only turn on wifi when I need it.
kinggrowler said:
I've made sure to set Wifi Sleep Policy to "Never" but that did not fix my wifi problems. What I see when I open Wifi Settings is a cycle of:
Code:
Scanning --> Connecting --> Disconnected... Scanning, etc
When I look in logcat it shows it attemping (in vain) to authenticate against the last wifi network I was using -- even though it is no longer in range (and clear across town). In a nutshell it is refusing to recognize the actual nearby network UNTIL I toggle wifi settings.
Click to expand...
Click to collapse
What is the point of having wifi set to ON when you are not in range of a network? Hence why, if you are using CM7 or CM6, you should utilize the notification widget and turn wifi off if you know you're leaving the area of your network. It's simple. Things aren't ALWAYS going to work how YOU want them to work. Thing will not always be automatic. I think I quote attn1 when I say this, just because it doesn't work how you want it to work, does not mean it is broken.
zervic said:
What is the point of having wifi set to ON when you are not in range of a network? Hence why, if you are using CM7 or CM6, you should utilize the notification widget and turn wifi off if you know you're leaving the area of your network. It's simple. Things aren't ALWAYS going to work how YOU want them to work. Thing will not always be automatic. I think I quote attn1 when I say this, just because it doesn't work how you want it to work, does not mean it is broken.
Click to expand...
Click to collapse
Well, just because people don't work exactly like you work, does not mean they are doing it wrong. If something is broken I'm going to call it out. I might be incorrect, but let's be clear: you aren't questioning that wifi in CM7 isn't working the way it did in CM6, you are questioning my behavior -- which is a weak argument.
I guess you don't understand the issue, so I'll spell it out:
Wifi worked flawlessly and automatically for me in stock 2.1 AND CM6. This automatic behavior does not work in CM7. Manually toggling something that simply "just worked" before is a regression, not a feature. Hence the reason I point it out -- the devs can't fix something unless they know it's broken, and I seriously doubt the devs are able to test all/every permutation. I have nothing but respect for the work they do, thus my very respectful tones in my earlier posts. I've had no indication that the devs are unwilling to get feedback about their work.
You asked a question though, and here is the answer:
I leave Wifi on all the time because I'm a consultant -- I work in many different locations throughout the week, travelling the country. I have dozens of wifi networks saved on my phone, and it is useful for me to have my phone automatically jump on the correct, nearest network. I'd rather use free wifi instead of paying AT&T for data charges. It is not always possible for me to remember I'm in a location with a known wifi network, or to remember to manually toggle wifi settings: it is useful for me to have this happen in the background. Sometimes I'm on a call, sometimes I'm heading into a meeting and I'd rather not mess with my phone. I want wifi to be on all time, scanning for the correct network, and jumping on it when it's in range.
Outrageous, right?! Not actually -- this is the existing behavior in CM6 and stock 2.1. From my standpoint, wifi just worked -- I didn't have to think about it, didn't have to manually toggle something to prevent AT&T data charges.
This is desired behavior for me, and I'm happy with rolling back to CM6 to get it. I understand that _you_ don't need this behavior, but that doesn't mean it's wrong. It just means the world is bigger than you realized.
And yes: wifi in CM7 (beta) is currently broken. Read the threads. Many people are having problems with it.
zervic said:
yup...that's why you just turn your wifi off with the notification widget (very simple and painless might I add) if you know you're leaving the house...what's the point of having wifi enabled if you're not in range of your network? all it's going to do is drain your battery. i left my wifi enabled one day when i sent to work and within half the day i had ~12% battery life...definitely not good practice to leave it enabled that's my 2 cents, do as you wish though. to each his own.
Click to expand...
Click to collapse
That's a good tip, I feel kind of dumb for not thinking about it lol and I also agree that it is good practice to do so. I just wanted to point it out in case a dev was going through this thread which is relevant to the topic.
Sent from my Liberty using XDA App
kinggrowler said:
Well, just because people don't work exactly like you work, does not mean they are doing it wrong. If something is broken I'm going to call it out. I might be incorrect, but let's be clear: you aren't questioning that wifi in CM7 isn't working the way it did in CM6, you are questioning my behavior -- which is a weak argument.
I guess you don't understand the issue, so I'll spell it out:
Wifi worked flawlessly and automatically for me in stock 2.1 AND CM6. This automatic behavior does not work in CM7. Manually toggling something that simply "just worked" before is a regression, not a feature. Hence the reason I point it out -- the devs can't fix something unless they know it's broken, and I seriously doubt the devs are able to test all/every permutation. I have nothing but respect for the work they do, thus my very respectful tones in my earlier posts. I've had no indication that the devs are unwilling to get feedback about their work.
You asked a question though, and here is the answer:
I leave Wifi on all the time because I'm a consultant -- I work in many different locations throughout the week, travelling the country. I have dozens of wifi networks saved on my phone, and it is useful for me to have my phone automatically jump on the correct, nearest network. I'd rather use free wifi instead of paying AT&T for data charges. It is not always possible for me to remember I'm in a location with a known wifi network, or to remember to manually toggle wifi settings: it is useful for me to have this happen in the background. Sometimes I'm on a call, sometimes I'm heading into a meeting and I'd rather not mess with my phone. I want wifi to be on all time, scanning for the correct network, and jumping on it when it's in range.
Outrageous, right?! Not actually -- this is the existing behavior in CM6 and stock 2.1. From my standpoint, wifi just worked -- I didn't have to think about it, didn't have to manually toggle something to prevent AT&T data charges.
This is desired behavior for me, and I'm happy with rolling back to CM6 to get it. I understand that _you_ don't need this behavior, but that doesn't mean it's wrong. It just means the world is bigger than you realized.
And yes: wifi in CM7 (beta) is currently broken. Read the threads. Many people are having problems with it.
Click to expand...
Click to collapse
fyi CM6 & 2.1 != CM7. Your argument is null & void.
Also, being a "consultant" and the very important man you are, flashing a rom that's not even in beta stages yet probably isn't the best idea you've ever had.
zervic said:
Also, being a "consultant" and the very important man you are, flashing a rom that's not even in beta stages yet probably isn't the best idea you've ever had.
Click to expand...
Click to collapse
Why do you remind us that the rom is in a beta stage? "Beta" implies it is not fully functional, but your argument all along has been that it works perfectly....
Look, it's clear you haven't actually understood any of my posts. I'm highlighting error messages or erratic behavior I see in logcat running CM7. I've posted what I've seen so the devs can take action, or not, as they choose. Since you aren't in that audience I don't understand what your beef is.
Oh wait! Straw man arguments; personal attacks; logical fallacies: I've been dealing with either a highschool student or a troll - not sure which.
zervic said:
fyi CM6 & 2.1 != CM7. Your argument is null & void.
Click to expand...
Click to collapse
...although I have a strong suspicion.
kinggrowler said:
Why do you remind us that the rom is in a beta stage? "Beta" implies it is not fully functional, but your argument all along has been that it works perfectly....
Look, it's clear you haven't actually understood any of my posts. I'm highlighting error messages or erratic behavior I see in logcat running CM7. I've posted what I've seen so the devs can take action, or not, as they choose. Since you aren't in that audience I don't understand what your beef is.
Oh wait! Straw man arguments; personal attacks; logical fallacies: I've been dealing with either a highschool student or a troll - not sure which.
...although I have a strong suspicion.
Click to expand...
Click to collapse
First of all:
attn1 said:
Just because something does not work they way you'd like it to doesn't mean you've discovered a bug.
Click to expand...
Click to collapse
That being said. Beta does NOT necessarily imply that thing are not fully functioning, it simply implies that it hasn't been put into RC or stable. You can have a fully functioning beta program. HOWEVER, it may not be working properly. But creating a thread about an issue that's been brought up 20+ times now is pointless. I'm PRETTY sure the devs know about the issue, should it actually be an issue. Now that I just wasted another 15 seconds of my life, i'm going to casually /part from this thread and I'll end my post with this quote again, in case you didn't catch it the first time.
attn1 said:
Just because something does not work they way you'd like it to doesn't mean you've discovered a bug.
Click to expand...
Click to collapse
This is for OP and very important man of the day, kinggrowler:
http://forum.xda-developers.com/showpost.php?p=11171075&postcount=1054
and i'll even quote it directly for you:
attn1 said:
There are no broad wifi issues to resolve, and I do not plan to change the wifi driver one iota. I am using the one that works right for most people, and flawlessly for me.
If you are not having such luck, then you need to look at your access point if you have already wiped data.
Really, the constant carping about wifi is absolutely pointless.
Click to expand...
Click to collapse
I believe the proper thing for me to say right now would be:
game. set. match.
Me too. I can't roam between networks, either. I have to disable and re-enable the wifi each time.
zervic said:
...what's the point of having wifi enabled if you're not in range of your network?
Click to expand...
Click to collapse
1) Because Google Maps uses known wifi hotspots to help establish your location.
2) So that you don't have to keep toggling wifi on and off when moving between hotspots (or home and work, for example).
3) To use the network notification feature (aka "notify me when an open network is available").
HTH
Edit: seems to be fixed in RC3!
zervic said:
What is the point of having wifi set to ON when you are not in range of a network? Hence why, if you are using CM7 or CM6, you should utilize the notification widget and turn wifi off if you know you're leaving the area of your network. It's simple. Things aren't ALWAYS going to work how YOU want them to work. Thing will not always be automatic. I think I quote attn1 when I say this, just because it doesn't work how you want it to work, does not mean it is broken.
Click to expand...
Click to collapse
i have try everything and still same issues with wifi. and i change the radio ( baseband ). still i am thinking of uninstalling it bc i dont have wifi
Sorry to tell you but that was with the old wifi stuff (every nightly up to build 25), which I had no problem with. The RC/nightlies have new wifi data made by jznomoney, which I have on and off problems with. Its working for most people but there are a handful who are having problems. I flashed ladios' kernel and my wifi is doing a lot better with the new RC/nightlies.
Signatures are fancy.
kinggrowler said:
I've made sure to set Wifi Sleep Policy to "Never" but that did not fix my wifi problems. What I see when I open Wifi Settings is a cycle of:
Code:
Scanning --> Connecting --> Disconnected... Scanning, etc
When I look in logcat it shows it attemping (in vain) to authenticate against the last wifi network I was using -- even though it is no longer in range (and clear across town). In a nutshell it is refusing to recognize the actual nearby network UNTIL I toggle wifi settings.
Click to expand...
Click to collapse
I've noticed something similar with CM7 on my Aria. When I leave the house and come back it doesn't always connect automatically and it will enter into this cycle of scanning, connecting, disconnected.
I had to reboot the phone to get it to stop the cycle and stay connected. I don't use a lot of data anyway but I still prefer to use wifi when available. Interestingly just now it wouldn't even see any of my neighbor's wifi networks at all which is odd.

Wifi issues

I've been having issues with wifi on my tab. I visit a friends house and it won't pick up the wifi. My phone picks it up fine, laptops pick it up ect. I stand AT the router and still it doesn't pick it up.
I thought it was a 1 off but it started happening at work too. The only differenceis that is WAS working fine at work, now won't pick it up. And now I have the same issue at my parents.
Does anyone else have this issue? Does anyone know a fix?
Cheers
Try wifi sleep policy and play with the options. Mine was set to "Never" and I was having random problems. Now set to "when screen turns off", and I never lose connection, screen on or off... On the other hand your problem may be different.
/reviveThread
Can't be sleep policy as it picks up other wireless networks fine.
I was just living with this issue until it lost my Home Wifi! Now thats gone I have to turn Hotspot on my phone, which I shouldn't have to do.
I thought it might be a problem with the ROM, so I've tried Task's GalaxyTask v5.0 and I still have the same issue. Might try flashing Stock and seeing if I get the same issue.
This is doing my head in now!
I flashed 3.2 Stock (rooted) and it picked up the missing Wifi connections. The rom is full of hebrew with silly boot and shutdown animations though. Tried flashing several custom 3.2 ROMS other than that and same issue as before.
Also, added connection manually and stood next to the Wifi antenna at work. Still got nothing. WTH is going on?
I read somewhere that Galaxy tab is not able to connect to some channels of wifi.
I believe it was not working with channels above 11
Try changing the channel and check
Thanks for the reply.
My home network is on channel 3. Plus it doesn't really explain how it can work 1 sec then totally disapear forever. Also doesn't explain how it works with the stock hebrew ROM but not with any others I've tried.
Just trying to find the wireless details for work now so I can change the channel anyway.
Then go with the Hebrew Rom and select English as language
Sent from my GT-P7510
ansonantonym said:
Then go with the Hebrew Rom and select English as language
Sent from my GT-P7510
Click to expand...
Click to collapse
I'd rather have no Wifi than see that nasty looking shutdown animation.
Anyway, problem seems to be semi resolved now.
Changed my wireless from channel 2 to 12, still didn't show. Back to 2, still didn't show. Changed it to 10 and it magically appeared.
Not sure what the work one is on. Still waiting for access.

Constant data use after reinstall

Hey guys
I just installed the leaked AT&T ICS (the CWM version that's been posted), and so far everything's generally great.
However, ever since I upgraded to ICS, my phone has been downloading data like crazy over WiFi. Oddly enough, this has happened on my phone before as well when I was using GB, and I believe it also occurred then right after a reinstall.
It's incredibly annoying because whatever the phone's downloading, it seems like it's using a lot of bandwidth because any other internet-related activities I try and do take *forever*. I've rebooted the phone several times, tried stopping every service that I can, and turned off all auto account sync stuff. It's been several hours since I installed ICS, and it's still going.
I'm going to let it sit overnight and see what it's doing in the morning, but even if this is only a temporary problem it's REALLY annoying. Especially since if it's not done doing whatever it's doing by morning, I won't be able to use cellular data on it because I only have the 200 MB plan and don't feel like losing my entire volume for the month because I can't stop my phone from downloading.
Any ideas as to what's causing this? Like I said I'm pretty sure this isn't an ICS-specific problem because it happened under 2.3.4 also, I just want to be able to shut down whatever's doing this excessive downloading. And I'd love to know *what* exactly is being downloaded that's it's taking so long and using so much bandwidth.
Thanks for any help you guys can lend
If you do switch to data to let it pull it down, you can use the data usage in the settings to see what app is doing it. My Data Manager (free in the Play Store) can also monitor data, on cell data and wifi. That would also tell you what app is doing it.
I would guess you either have a ton of data in your Google account, such as contacts, calendar, Gmail, or you have an app that is trying to sync data down. I'm guessing you are restoring apps, then notice the data draw. Think about any apps you have that may sync data back and forth. If you sign into your Google account at initial set up, it should (depending on settings) automatically download and install your apps. But, that should be apparent, you should see the downloads as it does them app by app.
All that is based on guesses of what I would consider "normal" behavior after installing a new ROM.
Good luck tracking it down. :thumbup:
Sent from my Galaxy S II (i777)
Settings > Data Usage
Check what is using it, and listing what APKs you added might help.
quarlow said:
If you do switch to data to let it pull it down, you can use the data usage in the settings to see what app is doing it. My Data Manager (free in the Play Store) can also monitor data, on cell data and wifi. That would also tell you what app is doing it.
Click to expand...
Click to collapse
Or avoid all that and use the native ICS data monitor.
The weird thing is that I hadn't really done anything to the phone when it started using all the data. My Google account doesn't really have much in it (don't have a ton of contacts, don't use it to back up apps/etc.), and I think the only things I'd done app-wise were updating a couple preinstalled apps (Facebook and Maps, I think), but I hadn't installed anything new yet.
I installed My Data Manager, but it looks like it's already done whatever it was doing. Though, even now the download arrow is constantly lit up on WiFi, but I think whatever it's doing now has something to do with the network I'm on (dorm room) as I've noticed almost constant non-zero download bandwidth being used on my desktop as well when it's on the network. If I turn WiFi off now it isn't constantly using cellular data any more, so thankfully it looks like it's finished with whatever it was doing and the constant WiFi downloading is a network, not phone, issue.
On an unrelated note, I was going to reinstall a tethering app, but figured I'd give a try to the built-in tethering first (don't have a plan). On GB it wouldn't even let me start up the tethering without a plan IIRC, but under ICS the tethering not only starts up, I can even connect my laptop to it. Unfortunately I couldn't get internet access on my laptop though, so I'm guessing there's still a restriction on it. Just found it interesting that you can actually enable the tethering without a plan now.
But there's a more serious problem, however. Is ATT clamping down on third-party tethering? I used to use Barnacle WiFi Tether, so I went to install that from the market. Well, Play tells me the app isn't able to be installed on my device because of carrier restrictions (lame). No problem, I figure, I go to their website and download the apk from there and manually install.
Well, when I try and start tethering using Barnacle, it says "WiFi: Could not set ad-hoc mode of wlan0: Operation not supported on transport endpoint"
Does this mean I'm screwed? Will any third-party tethering apps work? To be honest I'm not really into trying out 5 million different ROMs on my phone and don't really mind TW at all, so I'd prefer to keep it stock. But I use my phone overseas and need to be able to use tethering, and if ATT is really clamping down on third-party apps then I'll be installing a completely stock kernel once one's easily available.
Thoughts? Anyone else experimented with tethering on UCLC2 yet?
Well, never mind regarding the tethering stuff - I'd still be interested anyway to know if ATT is trying to actively prevent you from using it in ICS, but I just flashed the SHOstock2 ROM and I gotta say I'm blown away. Even after using it for a half hour I'm pretty sure I'll never go back to stock again (I'm sure most of you would say DUH to that), has everything I'd want in a ROM and nothing I don't. Default tethering works right out of the box too, so I don't even have to worry about installing another app.
Only kinda weird thing is the data indicator keeps switching between H+ and 3G (I'd post on the actual ROM thread but I don't have 10 posts yet...). I'm only on the 200 MB data plan so I switched it to the wap.cingular APN, but even after doing that it still switches. Data seems fast - and I'm not one to be super-concerned with data speeds since I'm mostly just checking e-mail - so it's not a huge deal, but figured I'd mention it anyway.
hbar said:
Well, never mind regarding the tethering stuff - I'd still be interested anyway to know if ATT is trying to actively prevent you from using it in ICS, but I just flashed the SHOstock2 ROM and I gotta say I'm blown away. Even after using it for a half hour I'm pretty sure I'll never go back to stock again (I'm sure most of you would say DUH to that), has everything I'd want in a ROM and nothing I don't. Default tethering works right out of the box too, so I don't even have to worry about installing another app.
Only kinda weird thing is the data indicator keeps switching between H+ and 3G (I'd post on the actual ROM thread but I don't have 10 posts yet...). I'm only on the 200 MB data plan so I switched it to the wap.cingular APN, but even after doing that it still switches. Data seems fast - and I'm not one to be super-concerned with data speeds since I'm mostly just checking e-mail - so it's not a huge deal, but figured I'd mention it anyway.
Click to expand...
Click to collapse
The data switching is normal. The device idles on 3g to save battery and kicks up to 4g when it needs the speed. Stock roms hide this behavior by showing the 4g icon even on 3g
Sent from my SGH-I777 using Tapatalk 2 Beta-4
LiLChris06 said:
Settings > Data Usage
Or avoid all that and use the native ICS data monitor.
Click to expand...
Click to collapse
I never thought to press the menu key in there, there is no indication there are more options. By default it doesn't show wifi data, but on my TouchPad running CM9, that's all it shows. Guess I shouldn't have assumed the ICS wouldn't be without menu use fragmentation like every other android version.
Yeah, the data switching on a custom ROM is normal. Just showing you what the phone actually does. It can save power by reverting back to the 3G vs H when you are idle. The first thing most custom ROMs add is tethering on the built in method. If the leak let you start it up, I'm guessing its incomplete. I would bet att does the same in ICS as GB and has an app to check your account before letting you turn on tethering. Att can detect tethering on the back end too, so if you are caught they warn you first, but you can end up being put on the tethering plan if you keep tethering.
Sent from my Galaxy S II (i777)
Ahh, thanks for the info on the data switching, never knew about that!
I don't use tethering in the US, but I do overseas, which is why I was concerned about ATT blocking tethering apps. However, I realized it's probably not an issue anyway because I'm guessing that tethering wouldn't be blocked with a non-ATT SIM card. Anyway, SHOstock rocks, so it's all good
Also good to know that ICS can monitor WiFi traffic by default - didn't think to hit the settings button on that screen. I gotta admit, that's one huge interface design flaw of Android. There should be some kind of indicator on the screen when there's a menu available, really poor interface design choice to have to hit the menu button randomly to see if any menus are there.
hbar said:
Also good to know that ICS can monitor WiFi traffic by default - didn't think to hit the settings button on that screen. I gotta admit, that's one huge interface design flaw of Android. There should be some kind of indicator on the screen when there's a menu available, really poor interface design choice to have to hit the menu button randomly to see if any menus are there.
Click to expand...
Click to collapse
With new ICS developed devices, most don't include touch buttons... The Nexus for example (using on screen buttons) only shows a menu button when a menu is available...
Cheers.
ALSO- I also noticed what appears to be constant "spurts" of Wifi data usage as well (at least according to my Wifi status bar indicator)... It doesn't seem to affect my Mobile Data, and every data monitoring App (including stock ICS data monitoring) doesn't show the culprit, which leads me to believe that we may be dealing with a system app that is accessing data in the background almost constantly... But only on Wifi. Maybe a location service, or something to do with Syncing? I say system because not even stock Data Monitoring is recognizing an app using data...
Another reason I say this is because I pointlessly wiped my device and started over due to this... "bug"... Only to find that running stock CM9 (with no installed apps) my Wifi indicator still led me to believe my device as downloading spurts of data constantly.
I haven't been able to narrow it down, and am hoping that the issue is fixed in a future software update. - But it is more than likely not an app, just an ICS/CM9 bug.
UPDATE- Just checked a Samsung Epic 4G running CM9 and the bug isn't there... So, it's something specifically within our device and ICS... Again, maybe a System app or Kernel bug...

WiFi often doesn't connect until settings are opened

After a few searches, I still can't find any posts about the exact issue I'm having with my WiFi.
Often my WiFi won't connect to my routers I have saved when I turn it on or leave one location and enter another. It will just sit at scanning until the moment I open the WiFi settings menu, then it suddenly finds routers. I can let it sit for a long time and it still won't find anything until I click the settings, then they pop up and connect automatically like they should.
Is this a common issue, or is i just my X2?
What ROM/android version number are you running? Need more data to tell you what is going on.
It's been no matter what ROM. CM9, Eclipse, stock, it's always done it. Not every time, but randomly hit and miss.
There is a known issue with CM7 not staying connected to wifi, but that was fixed with CM9.
That issue shouldn't happen on stock though. It almost sounds like a hardware issue in your case.
That's what I was wondering. It's been the same since I've had it, and has never gotten worse, so I've just lived with it.
Droid X2 > Eclipse 2.2.1 > Tapatalk
Yeah I can confirm this, mine does the exact same thing.
I don't get the disconnects that some people do (I may be using a patch related to the wifi sleep policy, I can't remember which roms that applies to), but it does the thing where it suddenly connects when you open settings, or the pulldown toggle only works half the time, or if you toggle it and then go to settings it can't actually find any networks.
Stuckinabox said:
Yeah I can confirm this, mine does the exact same thing.
I don't get the disconnects that some people do (I may be using a patch related to the wifi sleep policy, I can't remember which roms that applies to), but it does the thing where it suddenly connects when you open settings, or the pulldown toggle only works half the time, or if you toggle it and then go to settings it can't actually find any networks.
Click to expand...
Click to collapse
I have the same symptoms. Even with stock ROM 2.3.5.
Stuckinabox said:
Yeah I can confirm this, mine does the exact same thing.
I don't get the disconnects that some people do (I may be using a patch related to the wifi sleep policy, I can't remember which roms that applies to), but it does the thing where it suddenly connects when you open settings, or the pulldown toggle only works half the time, or if you toggle it and then go to settings it can't actually find any networks.
Click to expand...
Click to collapse
Exactly. I don't ever get disconnects on any ROM. Though while settings can't find any networks is pretty uncommon, it happens.
Stuckinabox said:
Yeah I can confirm this, mine does the exact same thing.
I don't get the disconnects that some people do (I may be using a patch related to the wifi sleep policy, I can't remember which roms that applies to), but it does the thing where it suddenly connects when you open settings, or the pulldown toggle only works half the time, or if you toggle it and then go to settings it can't actually find any networks.
Click to expand...
Click to collapse
Exactly. I don't ever get disconnects on any ROM.
DigitalMD said:
I have the same symptoms. Even with stock ROM 2.3.5.
Click to expand...
Click to collapse
Yup, even with stock. And every ROM I've ever tried.
It's kinda good to know it isn't just me.

[Q] no push notifications on wifi with KK

I upgraded my phone to KK back in late december and have been on it ever since but one problem has plagued me since then and I'm hoping to get some insight here. heres the problem...
When im connected to wifi (and this is only with wifi, not MD) I don't get my push notifications (gmail,fb,words,hangouts,etc) when the screen is off.Often i turn my screen on and get a barrage of notifications that i should have gotten hours ago. Ive tried all the sleep modes and Ive tried turning off wifi optimization.Nothing works and I know for fact it did not do this on JB.
I DO get text messages and phone calls instantly though but nothing else will wake my phone up. While i do enjoy the deep sleep, i would like to get my notifications in a reasonable amount of time without having to turn the phone on to check them.
Has anyone else had this "problem"?
Nope. Have you looked into what is and isn't checked in your Google Settings? There's a Play Games tab that allows you to mute certain games, essentially stopping their notifications. I don't suppose you've messed with that, have you?
It's strange, I've not really heard of this, especially since you're getting texts and such.
SteveMurphy said:
Nope. Have you looked into what is and isn't checked in your Google Settings? There's a Play Games tab that allows you to mute certain games, essentially stopping their notifications. I don't suppose you've messed with that, have you?
It's strange, I've not really heard of this, especially since you're getting texts and such.
Click to expand...
Click to collapse
Yeah i know and I've googled it to death for a few months now. I'll check g settings but idk why that would stop gmail. It's like when I'm on Wi-Fi w/ the screen off its just a plain old dumb phone. I turn the screen on and the notifications just flood in.
Edit: nothing in g settings is muted. The only thing i can think of is i don't have app data synced in accounts.
I think i figured it out. I had "sync app data" unchecked in accounts. So far I've been getting notifications screen on and off. Now if someone will just play back to me on wwf...
EDIT: i may have spoke too soon. It still doesnt wake up without turning on my screen
hey @SteveMurphy do you by chance use the active display?
razen_kain said:
hey @SteveMurphy do you by chance use the active display?
Click to expand...
Click to collapse
I did when I was using Omni and it worked great. I haven't used it since running RR, however.
So you're wifi connected, and have actively turned mobile data off? I have never even tried that...
If, however, you mean that this happens only when you're connected to WiFi, then no, I have not experienced this issue.
The only other setting that I can think of that pertains to sync is in system settings > Data usage > settings > [ ] auto-sync data, but I don't think that would cause the awake-vs-sleep sync issues that you're describing.
I used to use Active display, I currently use AcDisplay, I'll likely go back to using the baked-in active display.
razen_kain said:
[...](and this is only with wifi, not MD) I don't get my push notifications (gmail,fb,words,hangouts,etc) when the screen is off.[...]
Click to expand...
Click to collapse
cyril279 said:
So you're wifi connected, and have actively turned mobile data off? I have never even tried that...
If, however, you mean that this happens only when you're connected to WiFi, then no, I have not experienced this issue.
The only other setting that I can think of that pertains to sync is in system settings > Data usage > settings > [ ] auto-sync data, but I don't think that would cause the awake-vs-sleep sync issues that you're describing.
I used to use Active display, I currently use AcDisplay, I'll likely go back to using the baked-in active display.
Click to expand...
Click to collapse
No i never turn mobile data off. I just meant that notifications come as expected when I'm on mobile data but on Wi-Fi, once the phone hits deep sleep (<a minute) i won't get notifications unless i turn the screen on.
I ask about active display because i remember when on resurrection ROM i was using it and getting notifications then and kind of forgot about it but I'm on PAC 4.4 now and it's doing it again. However i was using the init.d scripts they have baked in but have them all turned back off now to see if that fixes it.
It's the strangest thing I've seen. It's like when I'm on Wi-Fi and turn the screen off it just disconnects from all data even though i can plainly see that it is not. Angela has the same phone with the same settings as mine but on RR 5.0.5 and she gets notifications fine.
@cyril279 I knnow this is off topic but have you tried this AD app? Its got some other features/customizations that aren't on the built in AD
https://play.google.com/store/apps/details?id=com.greatbytes.activenotifications
That was actually one of the first active-display variants that I tried. It worked well, but there were a couple hiccups that kept me shopping. The add-on AD clones have great features, but they don't play well with the stock lockscreen, or they leave the [home] button active, or involve significant lag when evoking the notification. The baked-in clones operate fluidly, but without the cool-stuff. I haven't tried active notifications recently though, maybe the updates have smoothed things out. I'm definitely down to try it again.
AcDisplay's development has been re-directed by Motorola. It's still my favorite of the clones, the beta version is boss, but it still isn't as fluid as the built-in boring-ol Omni AD.
razen_kain said:
@cyril279 I knnow this is off topic but have you tried this AD app? Its got some other features/customizations that aren't on the built in AD
https://play.google.com/store/apps/details?id=com.greatbytes.activenotifications
Click to expand...
Click to collapse
cyril279 said:
That was actually one of the first active-display variants that I tried. It worked well, but there were a couple hiccups that kept me shopping. The add-on AD clones have great features, but they don't play well with the stock lockscreen, or they leave the [home] button active, or involve significant lag when evoking the notification. The baked-in clones operate fluidly, but without the cool-stuff. I haven't tried active notifications recently though, maybe the updates have smoothed things out. I'm definitely down to try it again.
AcDisplay's development has been re-directed by Motorola. It's still my favorite of the clones, the beta version is boss, but it still isn't as fluid as the built-in boring-ol Omni AD.
Click to expand...
Click to collapse
Well all my testing so far has lead me no where with the exception of using that app. So far, I've not been able to reproduce the problem while using it. The question is,"what is it doing" to make it work....
EDIT: The app does not fix it....
just thinking out loud herebut, could this be a kernel issue? Im currently using PAC's kernel that comes packaged in the rom. Maybe I should try @RenderBroken 's kernel...?
Edit: Using RB's kernel breaks some of the PAC features and it did not fix my notification issue
https://code.google.com/p/android/issues/detail?id=42272
razen_kain said:
just thinking out loud herebut, could this be a kernel issue? Im currently using PAC's kernel that comes packaged in the rom. Maybe I should try @RenderBroken 's kernel...?
Edit: Using RB's kernel breaks some of the PAC features and it did not fix my notification issue
https://code.google.com/p/android/issues/detail?id=42272
Click to expand...
Click to collapse
PAC uses a modified ramdisk compared to other CM derived roms. Are you only having issues trying to get PAC running on your phone? Is it KK or JB?
RenderBroken said:
PAC uses a modified ramdisk compared to other CM derived roms. Are you only having issues trying to get PAC running on your phone? Is it KK or JB?
Click to expand...
Click to collapse
Its 4.4 and I have faced this issue on every rom Ive tried since switching to KK. Im starting to wonder if it's not an issue with my wifi. Im wondering if maybe my wifi is suspending my connection when my phone goes quiet.
RenderBroken said:
PAC uses a modified ramdisk compared to other CM derived roms...
Click to expand...
Click to collapse
Render, great information as always. razen, I'm no help to you on this - just felt like popping in to say "hi".
SteveMurphy said:
Render, great information as always. razen, I'm no help to you on this - just felt like popping in to say "hi".
Click to expand...
Click to collapse
It's always good to have you around buddy.
[SOLVED] Not Receiving Notifications on WiFi
My suspicions have paid off!! I started suspecting my router was the culprit so i pulled out my old netgear2400 and hooked it up and low and behold my notifications starting lighting my phone up again!!
The problem was the Xfinity router that came from comcast. Apparently it was closing the "heartbeat" line to stay connected when the screen was off before the heartbeat would send again, if that makes sense.
For the time being I'm going to just use my netgear router BUT I was able to fix the problem with the Xfinity router by using an app called Push Notification Fixer. Just install it, follow the instructions, and set the WIFI/mobile data heartbeat to the recommended settings. If that don't work start shortening the heartbeat time. It'll make sense when you see the app.
Hope this helps someone else along the way. I went a LONG WAY down the google rabbit hole before I figured this one out.
Great news, glad it was an easy fix!
razen_kain said:
My suspicions have paid off!! I started suspecting my router was the culprit so i pulled out my old netgear2400 and hooked it up and low and behold my notifications starting lighting my phone up again!!
The problem was the Xfinity router that came from comcast. Apparently it was closing the "heartbeat" line to stay connected when the screen was off before the heartbeat would send again, if that makes sense.
For the time being I'm going to just use my netgear router BUT I was able to fix the problem with the Xfinity router by using an app called Push Notification Fixer. Just install it, follow the instructions, and set the WIFI/mobile data heartbeat to the recommended settings. If that don't work start shortening the heartbeat time. It'll make sense when you see the app.
Hope this helps someone else along the way. I went a LONG WAY down the google rabbit hole before I figured this one out.
Click to expand...
Click to collapse
Great news! Now you just need to install DD-wrt on your router and turn it from a $40 router to a $400. I know you like to tinker but check it out. ITs free and its just firmware for certain routers. It turned my old wrt54g into a baus
razen_kain said:
My suspicions have paid off!! I started suspecting my router was the culprit so i pulled out my old netgear2400 and hooked it up and low and behold my notifications starting lighting my phone up again!!
The problem was the Xfinity router that came from comcast. Apparently it was closing the "heartbeat" line to stay connected when the screen was off before the heartbeat would send again, if that makes sense.
For the time being I'm going to just use my netgear router BUT I was able to fix the problem with the Xfinity router by using an app called Push Notification Fixer. Just install it, follow the instructions, and set the WIFI/mobile data heartbeat to the recommended settings. If that don't work start shortening the heartbeat time. It'll make sense when you see the app.
Hope this helps someone else along the way. I went a LONG WAY down the google rabbit hole before I figured this one out.
Click to expand...
Click to collapse
I'm having the same issue with KitKat CM11 ROM on my HP Touchpad (which is WiFi only), and will have to try this. Notifications come in instantly on my iPhone/iPads, but my Touchpad gets some serious delays...sometimes right away, and sometimes delayed.
By the way, did "Sync App Data" setting for an account have anything to do with push notifications, or is that more for backup purposes?
---------- Post added at 02:32 PM ---------- Previous post was at 02:04 PM ----------
Oh darn, mine is still delayed even with the push notification fixer installed and WiFi heartbeat at 5min. Even after I've just rebooted my Touchpad, actively using it, and not even 5 minutes has passed. Delay was 8 minutes and then the notifications came streaming in.
With Android/KitKat, do you have to have the app open in the background for push notifications to go thru? Or run the app at least once after a reboot?

Categories

Resources