so i went to switch out my battery and when i turned the phone back on it vibrated and displayed the white htc screen, then went black for a second and then stays on the white htc screen forever! Im a total noob when it comes to all the technical stuff about RUU's Kernels Roms and whatnot. I can get to bootloader, but i tried to do factory reset and it showed a green circle with a loading bar but then it changed into a red triangle with an exclamation. I tried flashing amon ra recovery but it doesnt work, although TWRP works. While in TWRP though, whenever i try to flash a zip file, it fails and says something like E:failed to mount /cache E:failed to mount /system E:failed to mount /data. Please help me i need this phone working to help me at my job. If someone can walk me through what i need to do i would REALLLYYYY appreciate it. Like i said though, i am a noob so i need realy stupified instructions lol. Thanks
just wanted to note that right now when i go to bootloader it says
*** TAMPERED ***
*** RELOCKED ***
*** Security Warning ***
Vigor PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
OpenDSP-v13.6.0.7611.00.0104
eMMC-boot
kverduin said:
just wanted to note that right now when i go to bootloader it says
*** TAMPERED ***
*** RELOCKED ***
*** Security Warning ***
Vigor PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
OpenDSP-v13.6.0.7611.00.0104
eMMC-boot
Click to expand...
Click to collapse
First you should go to shipped-roms.com and download the vigor ics ruu.exe, the rezound downloads there are under vigor . Plug your phone into your computer and from hboot highlight fastboot press power and run the .exe file from your computer and follow the on screen instructions, this will return your phone to full stock ics. Make sure you download the vigor ics ruu.exe as the GB ruu will not work with s-on.
You can also download this: http://www.androidpolice.com/2012/0...ull-ruu-build-4-03-605-2-for-the-htc-rezound/ it's the latest ruu it'll update your hboot, stock recovery, rom, and radios, to latest stock. Just download, rename the zip file to PH98IMG (don't include .zip it is a zip file it'll add it on its own in hboot) put it on your sd card, not in a folder just on. Put it back in your phone and boot to bootloader and runn the update, when it powers off. Run it again. (As it has to update the hboot to 2.27 first)Then you'll be on the stock latest. Then root and Rom from there. Of you need help pm me for my gtalk and I could walk you thru it..
sent from my s-off reZound rockin' viperRez Rom on global ICS firmware
Sounds like no boot.img
GrayTheWolf said:
Sounds like no boot.img
Click to expand...
Click to collapse
Its because of the security warning. The phone wont boot if it says that he has to run an RUU
Sent from my HTC Droid Incredible
Same exact problem. Installing zip now, god i hope this works!!
So my screen is the exact same, i tried to flash a kernal for not only wrong phone but wrong carrier too. Anyways no OS, when i try to flash either of the ways you have explained they both dont work. When i put it on the sd card as PH98IMG it looks like it loads it in the upper right then thats it. regular bootload screen after that nothing happens. try to load it by opening the application after im plugged in as fasboot usb and the program says Install script setup launcher has stopped working. I have been able to flash liquids rom and looks as if it is booting but waited 24 min and nothing happpend just stayed on boot screen. So im just trying to get back to RUU then work from there.
mrcorson said:
So my screen is the exact same, i tried to flash a kernal for not only wrong phone but wrong carrier too. Anyways no OS, when i try to flash either of the ways you have explained they both dont work. When i put it on the sd card as PH98IMG it looks like it loads it in the upper right then thats it. regular bootload screen after that nothing happens. try to load it by opening the application after im plugged in as fasboot usb and the program says Install script setup launcher has stopped working. I have been able to flash liquids rom and looks as if it is booting but waited 24 min and nothing happpend just stayed on boot screen. So im just trying to get back to RUU then work from there.
Click to expand...
Click to collapse
You need to extract the boot.IMG from liquid Rom and rename it ph98img and put that on your sd card or in the folder with adb and fastboot flash it using fastboot flash boot boot.img
Sent from my ADR6425LVW using xda app-developers app
Also wipe cache and dalvik cache in recovery immediately after doing this
Sent from my P4R4N01D R3D D347H 4.3 using xda app-developers app
I ended up flashing liquidsmooth rom in recovery then had to wipe factory data reset, then i could wipe dalvick cache then when i rebooted it actually booted the rom and I LOVE IT. Still having some issues tho.
Still cant get my computer to talk to my phone when in fastboot usb i cant get any devices when i do "adb devices" cmd.
It says devices listed below but no devices.
Also im still stuck on TWRP 2.2 and I cant my 2.6 to flash in recovery. - Still troubleshooting this and might get it in a bit.
Thanks for the suggestions!!!
mrcorson said:
I ended up flashing liquidsmooth rom in recovery then had to wipe factory data reset, then i could wipe dalvick cache then when i rebooted it actually booted the rom and I LOVE IT. Still having some issues tho.
Still cant get my computer to talk to my phone when in fastboot usb i cant get any devices when i do "adb devices" cmd.
It says devices listed below but no devices.
Also im still stuck on TWRP 2.2 and I cant my 2.6 to flash in recovery. - Still troubleshooting this and might get it in a bit.
Thanks for the suggestions!!!
Click to expand...
Click to collapse
ooooh older stuff ick lol...do you have your htc sync drivers installed....what os are you on? are you s-on? what hboot you on? you need to be wiping before rom install and not after....are your issues pertaining to random reboots?
REV3NT3CH said:
ooooh older stuff ick lol...do you have your htc sync drivers installed....what os are you on? are you s-on? what hboot you on? you need to be wiping before rom install and not after....are your issues pertaining to random reboots?
Click to expand...
Click to collapse
Yes i did reinstall my HTC Sync drivers, I have been wipining factory reset, cache, system, dalvick cache before i flash a new rom. I am S-On. Havent really determined a reason to go s-off yet, i am messing up my phone good enough with this let alone a paperclip. no problem with random reboots. I finally decided to go to a custom rom bc i was sick of my phone rebooting for OTA updates then being late for work. So the 3 roms i have now tried are Liquid smooth which i liked but i couldnt get mms messages to show up on phone. Also it wouldnt change from silent to a beep for text message notifications. i could select it but it would stay as silent. So.... I flashed ViperRezROm which i just didnt like the look and theme. So i finally flashed Cyanogen ROM and come to find out its the same kernal as Liquid smooth so it looks the same and I like that but I still cant change the notification from silent to a beep for text messages. So i never know when i get a text.
Still working on trying to flash a newer version of TWRP.
Then this time flashing I tried to titanium backup and went to load my backup and it cant find it.... WTF
UGH... Learning so much with this stuff. just taking alot of patience.
Thanks again for yalls support, I love this forum.
Mike
BTW just to note...if your bootloader is locked fastboot flash methods will not work 90 percent of the time...if you flashed liquid 3.0 that's more than likely your problem with mms as that is a beta...but on more recent 4.3 builds mms is fixed...and no its not the same kernel...just similar source code...liquid 2.9 does not have this mms issue...any random reboots on 4.2 are caused by min frequency not set right at 384 mhz and using amon ra to flash or not doing a proper clean flash....I do recommend s-off as it will make life much easier for you for modding things or flashing custom zips and for future flashing back to full stock if needed as its not possible while s-on...you can always pm me for help as I've yet to run into an error I can't fix unless posted in op caused by source
Sent from my P4R4N01D R3D D347H 4.3 using xda app-developers app
There is a few good reasons to S-Off.
1.No need to fastboot flash kernels
2.can RUU if needed
3.can flash recovery updates (cwm, twrp) as ph98img zips
4. Can keep bootloader ***locked***
5. No more ***tampered*** tag after you RUU
Scenario: you are out and about (or a computer isn't handy) somehow you are in an infinite bootloop. You nandroid restore. But it is something on boot partition. Only way to fix this while S-On is fastboot flashing a boot.img, but if you were S-Off, you would have restored the boot image from the nandroid.
Edit: added 5th reason
Sent from my ADR6425LVW using xda app-developers app
Uzephi said:
There is a few good reasons to S-Off.
1.No need to fastboot flash kernels
2.can RUU if needed
3.can flash recovery updates (cwm, twrp) as ph98img zips
4. Can keep bootloader ***locked***
5. No more ***tampered*** tag after you RUU
Click to expand...
Click to collapse
I finally went S-OFF to help another user get step by step to restore to fully locked and stock ruu. I decided to leave it S-OFF. It's so nice to be able to just load a rom and not have to do anything else (other than wiping). It makes changing/upgrading rom's a breeze.
I highly recommend it. It seems scary, but once you have done it once, you will not go back.
But be warned, never go back to S-ON on a non-HTC hboot... you will hard brick your device. That is the only real threat I've heard about... if you never go back to S-ON, then you have absolutely nothing to worry about. Just about any error can be fixed except for going s-on on a non-ruu hboot.
Thanks
molson8045 said:
You need to extract the boot.IMG from liquid Rom and rename it ph98img and put that on your sd card or in the folder with adb and fastboot flash it using fastboot flash boot boot.img
Sent from my ADR6425LVW using xda app-developers app
Click to expand...
Click to collapse
You saved me! That worked like a charm.
please help
Hi guys
Im have that problem in my htc rezound i seen the above comments but i couldnt able to understand so please tell the procedure one by one please pleasr..........
parthis said:
Hi guys
Im have that problem in my htc rezound i seen the above comments but i couldnt able to understand so please tell the procedure one by one please pleasr..........
Click to expand...
Click to collapse
If English is not your first language I apologise.
Otherwise, you need to be more specific and use full sentences.
GrayBoltWolf said:
Sounds like no boot.img
Click to expand...
Click to collapse
you were dead on accurate regarding my problem. Your post helped me revive an all but dead rezound!! Thanks man!!
Related
Okay, so I'm in a bit of a bind. I'm S-OFF, and I tried updating to the global leak and it seems I've lost boot and recovery. Everytime I boot it goes through the splash screen and then a black screen with the phone and green update symbol, then it turns to a red triangle and exclamation mark. any help would be greatly appreciated. I'm fairly experienced and everything i've tried has failed. I tried going into hboot and flashing the PH98IMG again. It took, but still the same result. I tried flashing the recovery in fastboot but it continues to fail, and I also tried flashing my boot.img but it also failed. Any ideas?
tomtripp21 said:
Okay, so I'm in a bit of a bind. I'm S-OFF, and I tried updating to the global leak and it seems I've lost boot and recovery. Everytime I boot it goes through the splash screen and then a black screen with the phone and green update symbol, then it turns to a red triangle and exclamation mark. any help would be greatly appreciated. I'm fairly experienced and everything i've tried has failed. I tried going into hboot and flashing the PH98IMG again. It took, but still the same result. I tried flashing the recovery in fastboot but it continues to fail, and I also tried flashing my boot.img but it also failed. Any ideas?
Click to expand...
Click to collapse
unlock the bootloader and flash a recovery. you need to unlock since you dont have eng commands.
btw this belongs in q&a
antp121 said:
unlock the bootloader and flash a recovery. you need to unlock since you dont have eng commands.
btw this belongs in q&a
Click to expand...
Click to collapse
Thanks I'll give that a try. Will the firmware and ROM still be in place? Will I have do the update again? BTW Sorry for posting it in the wrong section..
tomtripp21 said:
Thanks I'll give that a try. Will the firmware and ROM still be in place? Will I have do the update again? BTW Sorry for posting it in the wrong section..
Click to expand...
Click to collapse
Its OK. And once you unlock, it'll reboot. Then you just go back into the boot loader and flash a recovery with fast boot.
Sent from my aokp_tenderloin using Tapatalk 2
So got the recovery flashed, but now it only boots into the recovery.
tomtripp21 said:
So got the recovery flashed, but now it only boots into the recovery.
Click to expand...
Click to collapse
Did you try flashig a rom?
Sent from my aokp_tenderloin using Tapatalk 2
i tried to restore my backup that didn't work, I haven't tried a new ROM yet. I'll try that and get back to you. Thanks again for all your help.
antp121 said:
Did you try flashig a rom?
Sent from my aokp_tenderloin using Tapatalk 2
Click to expand...
Click to collapse
Tried flashing a ROM, the stock deodexed rooted 4.03.605.02. Still boots to recovery...
tomtripp21 said:
Tried flashing a ROM, the stock deodexed rooted 4.03.605.02. Still boots to recovery...
Click to expand...
Click to collapse
You need to use interface to fastboot boot.img then run firmware update for old firmware n old CWR. BASICALLY GO BACK TO STOCK REZOUND N START THE WHOLE PROCESS OVER LIKE DAY 1!
Good news is you don't need to do the wire trick again. Your phone crashed during the firmware upgrade now its stuck in limbo n doesn't know how to handle the 2 sets of hardware commands its receiving from the CMOS.
[Q] Can only get into recovery after attempting Juopunutbear S-OFF
I wanted to S-OFF after being stock locked, with the OTA ICS update. I performed HTC dev unlock successfully. After that, I may have gone wrong during one of several steps.
-Pushed AmonRa recovery 3.15 to my phone (seemed to be successful)
-Flashed ICE-EnableRoot.img (got an error message saying it was unsuccessful, but when I rebooted my phone, SuperUser was installed).
-Flashed vigorOTAStockRooted.zip (because I wanted to try the S-OFF method from stock GB rom)
-Ran HTC Rezound S-OFF Kit By Hasoon2000
-Made sure HTC Drivers were installed
-Enabled USB Debugging
-Put in blank SD Card
-Run Juopunutbear v.6 If You Are On Gingerbread
After running Juopunutbear v.6 for Gingerbread, my phone screen went blank and HTC's splash screen came up momentarily, and then my phone screen went dark. The cmd box that popped up then gave me an error message saying I had to install the HTC Drivers. I went to HTC's website to download the drivers. When I tried to install them, I was told they were already installed.
I can reboot my phone into Hboot and AmonRa recovery and I can do anything from there. But when I try to start my phone, I get the HTC splash screen and then black screen. The orange LED lights up when my phone is powered off and plugged in via USB. When I try to boot from Hboot, I either get a static HTC splash screen or splash screen going to a black screen.
This is what my Hboot screen reads:
*** TAMPERED ***
*** UNLOCKED ***
VIGOR PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
Open DSP-v13.6.0.7611.00.0104
eMMC-boot
Apr 12 2012,16:47:46
Any advise would be greatly appreciated! Thank you!
jtayag said:
I wanted to S-OFF after being stock locked, with the OTA ICS update. I performed HTC dev unlock successfully. After that, I may have gone wrong during one of several steps.
-Pushed AmonRa recovery 3.15 to my phone (seemed to be successful)
-Flashed ICE-EnableRoot.img (got an error message saying it was unsuccessful, but when I rebooted my phone, SuperUser was installed).
-Flashed vigorOTAStockRooted.zip (because I wanted to try the S-OFF method from stock GB rom)
-Ran HTC Rezound S-OFF Kit By Hasoon2000
-Made sure HTC Drivers were installed
-Enabled USB Debugging
-Put in blank SD Card
-Run Juopunutbear v.6 If You Are On Gingerbread
After running Juopunutbear v.6 for Gingerbread, my phone screen went blank and HTC's splash screen came up momentarily, and then my phone screen went dark. The cmd box that popped up then gave me an error message saying I had to install the HTC Drivers. I went to HTC's website to download the drivers. When I tried to install them, I was told they were already installed.
I can reboot my phone into Hboot and AmonRa recovery and I can do anything from there. But when I try to start my phone, I get the HTC splash screen and then black screen. The orange LED lights up when my phone is powered off and plugged in via USB. When I try to boot from Hboot, I either get a static HTC splash screen or splash screen going to a black screen.
This is what my Hboot screen reads:
*** TAMPERED ***
*** UNLOCKED ***
VIGOR PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
Open DSP-v13.6.0.7611.00.0104
eMMC-boot
Apr 12 2012,16:47:46
Any advise would be greatly appreciated! Thank you!
Click to expand...
Click to collapse
For starters, you are on ics firmware so you should run the ics version of juopunutbear. I suggest flashing a rooted Rom based on the ota and then try again.
Sent from my ADR6425LVW using Tapatalk 2
topgun1953 said:
For starters, you are on ics firmware so you should run the ics version of juopunutbear. I suggest flashing a rooted Rom based on the ota and then try again.
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
I successfully flashed one of the stock ICS ROMs! What got me all confused to begin with was the prerequisite that I had to be on a stock Gingerbread ROM or the 3.14.605.5 ICS leak. That's why I tried flashing the original Vigor GB ROM on my phone. I still want to get S-OFF, but I need to read the instructions more carefully. Thanks for your help!
dragonstalker said:
You need to use interface to fastboot boot.img then run firmware update for old firmware n old CWR. BASICALLY GO BACK TO STOCK REZOUND N START THE WHOLE PROCESS OVER LIKE DAY 1!
Good news is you don't need to do the wire trick again. Your phone crashed during the firmware upgrade now its stuck in limbo n doesn't know how to handle the 2 sets of hardware commands its receiving from the CMOS.
Click to expand...
Click to collapse
So I just need to flash my backed up boot.img, and then flash the 3.14.605.12 RUU? Then re-root and retry the OTA Global Update?
tomtripp21 said:
So I just need to flash my backed up boot.img, and then flash the 3.14.605.12 RUU? Then re-root and retry the OTA Global Update?
Click to expand...
Click to collapse
pretty much. From looking at everything looks like you are on ICS, but its not letting you reprogram. usually happens when an update fails. When you run Juonobear and run the ics upgrade over again, it should reboot like 3 or 4 times. Sounds like you never let the process finish. Final note, i'm not sure where you got your firmware from, but your radios do not look familiar. Not saying they are wrong, just not radio's i've ever seen flashed. BUT, I don't usually change radio's unless there is a huge need for it. you should be on radio's 10r/08r that come with the original ICS firmware update. I'll watch the thread throughout the day to lend support where I can. Hope this helps.
dragonstalker said:
pretty much. From looking at everything looks like you are on ICS, but its not letting you reprogram. usually happens when an update fails. When you run Juonobear and run the ics upgrade over again, it should reboot like 3 or 4 times. Sounds like you never let the process finish. Final note, i'm not sure where you got your firmware from, but your radios do not look familiar. Not saying they are wrong, just not radio's i've ever seen flashed. BUT, I don't usually change radio's unless there is a huge need for it. you should be on radio's 10r/08r that come with the original ICS firmware update. I'll watch the thread throughout the day to lend support where I can. Hope this helps.
Click to expand...
Click to collapse
Now I'm a little confused, sorry. I need to run the juopunutbear program again? My radios are 2.22.10.0801r/2.22.10.0803r, Hboot 2.27. I'm downloading the .12 RUU from Android Police. I've tried re-flashing the boot.img from my nand backup, but it keeps saying:
C:\mini-adb_vigor>fastboot flash boot.img
unknown partition 'boot.img'
error: cannot determine image filename for 'boot.img'
edit: I fixed the flash, I forgot to add the partition in the command, duh... So I flashed my backed up boot.img, now I just need to flash the .12 RUU?
I have the backup img in the file where I have fastboot, adb, etc.. What am I doing wrong?
tomtripp21 said:
Now I'm a little confused, sorry. I need to run the juopunutbear program again? My radios are 2.22.10.0801r/2.22.10.0803r, Hboot 2.27. I'm downloading the .12 RUU from Android Police. I've tried re-flashing the boot.img from my nand backup, but it keeps saying:
C:\mini-adb_vigor>fastboot flash boot.img
unknown partition 'boot.img'
error: cannot determine image filename for 'boot.img'
edit: I fixed the flash, I forgot to add the partition in the command, duh... So I flashed my backed up boot.img, now I just need to flash the .12 RUU?
I have the backup img in the file where I have fastboot, adb, etc.. What am I doing wrong?
Click to expand...
Click to collapse
I have now tried to flash the .12 RUU in Hboot but it will not flash it, probably because my firmware is newer right? Back to the drawing board....
Still to no avail I am getting nowhere. I flashed the stock recovery and did a factory reset from Hboot. Nothing, I have tried flashing the newest RUU, nothing, I'm flashed back to ra-recovery. Can anybody give me a solution step by step to get a ROM loaded and booting?
Well I finally got it up and working. I loaded the old firmware and was able to restore by backup. Thanks to all who chimed in with helpful advice. I'm hesitant to retry the Global update, but I might go ahead and give it another shot.
Glad you figured to restore the firmware. It's not hard to flash the global. Run the firmware, then run the recovery then flash Rom. Do it right in that order n you don't have any issues. Use 2 sdcards if you need to because the firmware upgrade won't delete the ph98 off your card. You will need to do it manually.
Sent from ICS REZOUND S-OFF
Hey im new to the fourms but i have a HTC evo 3d on the Sprint network. I am unlocked S-On hboot 1.58 with MeanRom ( the latest) i am suffering from a boot loop. The screen boots i see the ring and then black screen back to HTC and restarts process. I am in way to over my head. Can anyone tell me if i can put a stock rom back on and it will fix boot loop or i heard about relock but don't know how to do it. Ive rooted other devices and jail broken devices but never had a problem like this. Help is much appreciated. Thanks
edit: I used a video on youtube but cant post the link :/
ClockWorkMod Recovery was used in it so i think i have it still.
I have tried the factory reset from the boot menu (power + vol down)
Tanker990 said:
Hey im new to the fourms but i have a HTC evo 3d on the Sprint network. I am unlocked S-On hboot 1.58 with MeanRom ( the latest) i am suffering from a boot loop. The screen boots i see the ring and then black screen back to HTC and restarts process. I am in way to over my head. Can anyone tell me if i can put a stock rom back on and it will fix boot loop or i heard about relock but don't know how to do it. Ive rooted other devices and jail broken devices but never had a problem like this. Help is much appreciated. Thanks
edit: I used a video on youtube but cant post the link :/
ClockWorkMod Recovery was used in it so i think i have it still.
I have tried the factory reset from the boot menu (power + vol down)
Click to expand...
Click to collapse
Don't panic tanker, lol I can help you out with this. Here is the reasons behind your boot loop
Your recovery,
Your hboot
Your kernel
Let me elaborate. Cwm has been known to cause lots of problem with evo3d flashing latest twrp or 4ext recovery is recommended. Highly for 4ext. Now before I explain about hboot and kernel, currently you are a s-on user. What that means is that you only have access to certain partitions in the nand memory. System, data, and recovery. That leaves radios and boot partition( that's where your kernel sits) inaccessible through normal recovery means. Anytime you flash a ROM inside of recovery, you phone can't flash the kernel that came with it. So in actuality, your still on stock kernel with mean ROM.
Now for the solution. Your in a endless boot loop with your phone so you will have to download 4ext recovery for your phone and place the recovery image in your fastboot directory. Hook your phone up to the computer and run the command fastboot flash recovery "whatever the name of recovery"img . Boot into recovery and navigate to tools directory. Scroll down and turn on smart flash. This feature will allow you to flash kernels within recovery for s-on users. Wioe everything and flash your ROM again.
Now as for your kernel. Hboot 1.58 is only compatible with ICS stock kernels. That's the main point of your problem. What you will need to do is navigate to the meanrom folder and select the 2.89 kernel and flash it. Your phone should be able to boot up properly after that.
If that doesn't work, you could also try the first step of Ramjet's thread. That will get you back to stock and hopefully not bootlooping. Then if you continue the steps, you'll be s-off which makes flashing easier. See: http://forum.xda-developers.com/showthread.php?t=1889438
Jsparta26 said:
Now for the solution. Your in a endless boot loop with your phone so you will have to download 4ext recovery for your phone and place the recovery image in your fastboot directory. Hook your phone up to the computer and run the command fastboot flash recovery "whatever the name of recovery"img . Boot into recovery and navigate to tools directory. Scroll down and turn on smart flash. This feature will allow you to flash kernels within recovery for s-on users. Wioe everything and flash your ROM again.
Now as for your kernel. Hboot 1.58 is only compatible with ICS stock kernels. That's the main point of your problem. What you will need to do is navigate to the meanrom folder and select the 2.89 kernel and flash it. Your phone should be able to boot up properly after that.
Click to expand...
Click to collapse
okay so i have downloaded 4extrecoveryupdater.apk
Now i would open up CMD and what do i type in for "whatever the name of revoery".img or is that just someting i make up?
sorry im a really noob
Tanker990 said:
okay so i have downloaded 4extrecoveryupdater.apk
Now i would open up CMD and what do i type in for "whatever the name of revoery".img or is that just someting i make up?
sorry im a really noob
Click to expand...
Click to collapse
Funny. No you cannot make up file names, or commands...
First of all you need fastboot application. Save it to c:/fastboot folder.
1. Open CMD, type cd fastboot to enter fastboot folder
2. Type : fastboot flash recovery recovery.img (where recovery.img is the name of your recovery choice weather it is TWRP, 3eXT, or CWM.
I am currently using 4eXT, which I switched to from TWRP
And that's it after its done you should have a flashed recovery on your EVO 3D
Maybe I should add that the "recovery.img" file HAS to be inside c:/fastboot folder.
Good luck. If that doesn't fix it, or if you need any recovery images that worked on my phone, POST
peteypub said:
Funny. No you cannot make up file names, or commands...
First of all you need fastboot application. Save it to c:/fastboot folder.
1. Open CMD, type cd fastboot to enter fastboot folder
2. Type : fastboot flash recovery recovery.img (where recovery.img is the name of your recovery choice weather it is TWRP, 3eXT, or CWM.
I am currently using 4eXT, which I switched to from TWRP
And that's it after its done you should have a flashed recovery on your EVO 3D
Maybe I should add that the "recovery.img" file HAS to be inside c:/fastboot folder.
Good luck. If that doesn't fix it, or if you need any recovery images that worked on my phone, POST
Click to expand...
Click to collapse
petey I am having the same issue as him, 1.58 hboot running ext4 recovery with smart flash on and i cant get out of a boot loop. i have tried using an ruu to return to stock (ruu fails/becomes non responsive). as well as flashing roms using ext4 and then flashing the boot image via fastboot.
if you could help me as well or send me any recovery files you have i would appreciate it
Sure ill send you the images I'm using. I'm at work now, so ill shoot you an email when I get back...
Sent from my PG86100 using Tapatalk 2
pm sent with email address
Youre in a boot loop because you need to downgrade your hboot see link below
Don't forget to hit the thank button!
http://forum.xda-developers.com/showthread.php?t=1906172
sent from my 1920 overclocked note 2 running jedi xp11
---------- Post added at 02:06 AM ---------- Previous post was at 02:05 AM ----------
Btw I use TWRP not 4ext. And forget the ruu.
Just downgrade and it will work
sent from my 1920 overclocked note 2 running jedi xp11
restore rom
When you flashed rom did u make back up cause you could always restore old rom. And you could try flashing the right kernel but most of the time it cause you have to flash boot image that worked for me in trying flash cm 10.1 and I keep get bootloops my self try figure this one out. Same hboot 1.58 2.89 base
harry1471 said:
When you flashed rom did u make back up cause you could always restore old rom. And you could try flashing the right kernel but most of the time it cause you have to flash boot image that worked for me in trying flash cm 10.1 and I keep get bootloops my self try figure this one out. Same hboot 1.58 2.89 base
Click to expand...
Click to collapse
Are you saying youre still getting boot loops and you havent figured this out yet or you did figure it out?
If you havent figured it out I can assist as ive got it 100% working
sent from my 1920 overclocked note 2 running jedi xp11
Same deal
markbencze said:
Are you saying youre still getting boot loops and you havent figured this out yet or you did figure it out?
If you havent figured it out I can assist as ive got it 100% working
sent from my 1920 overclocked note 2 running jedi xp11
Click to expand...
Click to collapse
I'm having the same problem:
Sprint EVO 3D
Unlocked
S-On
Hboot 1.58
eMMC-boot
Won't boot any rom past the OS lock screen. Tried relocking and RUU update, Tried booting recovery from fastboot.
Any help?
Thanks!
jy04 said:
I'm having the same problem:
Sprint EVO 3D
Unlocked
S-On
Hboot 1.58
eMMC-boot
Won't boot any rom past the OS lock screen. Tried relocking and RUU update, Tried booting recovery from fastboot.
Any help?
Thanks!
Click to expand...
Click to collapse
Give me a bit mire info on this. I can help for sure. The evo3d is a pita but we can get it. So basically if I understand, you're stock rooted but have s-on and im assuming all roms are bootlooping?
sent from my Jedi powered Note ll
respect, teach & coach, have fun and say thanks!
the Jedi way
markbencze said:
Give me a bit mire info on this. I can help for sure. The evo3d is a pita but we can get it. So basically if I understand, you're stock rooted but have s-on and im assuming all roms are bootlooping?
sent from my Jedi powered Note ll
respect, teach & coach, have fun and say thanks!
the Jedi way
Click to expand...
Click to collapse
Yes, that's were I am at this point. Right now I've got MeanRom booting to the homescreen seems like it's going to work, but the time is wrong and there's no service, before it can completely boot, bam, shuts down and reboots.
It does the same for the stock Sprint ROM.
Unfortunately I didn't make a backup of the phone when I gor it so I'm using a downloaded one.
I had Meanrom running on another 3D not too long ago, but don't remember it being this troublesome. What did I miss?
jy04 said:
Yes, that's were I am at this point. Right now I've got MeanRom booting to the homescreen seems like it's going to work, but the time is wrong and there's no service, before it can completely boot, bam, shuts down and reboots.
It does the same for the stock Sprint ROM.
Unfortunately I didn't make a backup of the phone when I gor it so I'm using a downloaded one.
I had Meanrom running on another 3D not too long ago, but don't remember it being this troublesome. What did I miss?
Click to expand...
Click to collapse
Ok well the first thing you need to do is downgrade your hboot to v 1.49000. I posted a link on the first page. If you were stock you coukd get s-off via the wire trick
But since you're s-on you need to flash the boot.img in fastboot and then flash the rom or vise versa. I cant remember which one needs to be done first as its been a while since I've used my evo3d. Basically anything thats ics and above cant be flashed unless you downgrade your hboot. Htc sent a hidden hboot ota to you at some point without your knowledge to prevent you from flashing. So downgrading your hboot is your #1 priority and you need to get back to stock to get s-off too
sent from my Jedi powered Note ll
respect, teach & coach, have fun and say thanks!
the Jedi way
Using the wrong ROM!! Got it to boot using MeanRom ICS. Thanks!
Can I get S-OFF with MeanRom flashed? Or do I need to flash a rooted stock ROM?
jy04 said:
Can I get S-OFF with MeanRom flashed? Or do I need to flash a rooted stock ROM?
Click to expand...
Click to collapse
You can try but the instructions say stock. You tube it. Ive done it. It works. Just be patient with the wire trick
sent from my Jedi powered Note ll
respect, teach & coach, have fun and say thanks!
the Jedi way
Hey everyone,
So I have successfully HTC Unlocked my Rezound bootloader, installed Amon Ra, and then installed and booted the CM9 unofficial. Problem was that CM9 wasn't quite as cooperative as I'd hoped - it is unofficial, after all, and so I decided to abandon that in favor of Nils' Business ROM. Here's where I ran into issues.
I have tried everything in every order I can find online and think of, including Nils' writeup. So, for the life of me, I cannot get the leaked ICS RUU to boot (4.03.605.2 as listed in his instructions on XDA). Install runs fine every time I do it from the relocked (I checked) stock HBOOT, all steps included. Every time it reboots (and I've tried forcing it back into hboot to do the install a second time) it just goes to the white HTC screen and starts boot looping. Tried it a million ways, no go. Also worth noting - the stock recovery doesn't install properly, either. Some'fin is hinky, here.
So I've tried just "assuming" it went fine anyhow and then proceeding with the install for Nils' ROM and same deal, no go, although with one difference. With Nils' ROM, it does display the boot splash screen "Nils Business ROM" or what have you about 1 out of every 4 "boots" in the loop cycle, and then reboots again.
I think I am going to perform S-OFF tomorrow if I have the time, and then try it again using the S-OFF instructions, but I would sincerely appreciate any help from you all. Honestly, I'm at near wit's end with this device, and I don't want to be, I enjoy this chase too much, but I *really* want the reward at the end of it, lol.
Any help is deeply appreciated.
- Katie
Re: [Q]
I'm guessing because of the corrupted recovery, you have a bad download of the RUU. Try re downloading and check the md5 hash for a match. The ruu should reboot itself after the first pass and end up in bootloader again for the second pass.... If not then after the first pass just hold down power + vol down to get back to bootloader.
Hope this helps
Sent from my ADR6425LVW using xda app-developers app
Make sure that you have a booting ROM before you s-off. You will cause yourself all kinds of heartache if you don't.
Using an sd card reader on a pc, check md5 of your RUU zip file. If it checks out good, put the sd back in your rez and do an hboot power on and accept the update again. Report back with your findings. Also you will need to re-unlock your hboot after and install your recovery again.
Snuzzo said:
Using an sd card reader on a pc, check md5 of your RUU zip file. If it checks out good, put the sd back in your rez and do an hboot power on and accept the update again. Report back with your findings. Also you will need to re-unlock your hboot after and install your recovery again.
Click to expand...
Click to collapse
Hey, thanks. Yeah, the RUU does check out just fine against an MD5SUM.
nm.... just read your original post again and you say you did relock the phone. I was hoping it was something simple like that that was overlooked.
Carry on...
feralicious said:
Nothing to see here, folks, move along.
Click to expand...
Click to collapse
Right now, I cannot S-OFF because it requires a working stock image, and I'll be lucky to get anything more than CM9 unofficial working here.
You're too fast, now my bad post lives on...
So, when theh RUU failed, you unlocked again, flashed a custom recovery and tried to flash Nils' ROM?
Do you have a nandroid you can try to restore? Even if its the cm9 ROM at least to see if you can get it back to a working phone?
feralicious said:
You're too fast, now my bad post lives on...
So, when theh RUU failed, you unlocked again, flashed a custom recovery and tried to flash Nils' ROM?
Do you have a nandroid you can try to restore? Even if its the cm9 ROM at least to see if you can get it back to a working phone?
Click to expand...
Click to collapse
Well that's the trick. CM9 didn't work well enough to even be worth backing up. I'm trying to reinstall it again now just to see if I get there - and it looks like I will. Once I'm back up with that, I'm not sure where to go from there. The phone barely worked under CM9. Really hoping to get Nils' ROM on there, since it gives all the nice features of a stock device without the bloatware. Even if I never get S-OFF, I'll be perfectly happy with just Nils' software.
How about this... did you wipe everything before running the RUU? There's CleanWipe in the Development forum you can flash it from recovery and it will wipe everything 5 times!
This shouldn't make any difference, but there's also a different RUU, the OTA that's not global. You might try that one instead. I'm convinced that sometimes things are just voodoo even when they should be completely logical. That's definitely the case at work on the Avid systems I use.
Here's the link to it:
http://androidfiles.org/ruu/?dir=Vigor
feralicious said:
How about this... did you wipe everything before running the RUU? There's CleanWipe in the Development forum you can flash it from recovery and it will wipe everything 5 times!
This shouldn't make any difference, but there's also a different RUU, the OTA that's not global. You might try that one instead. I'm convinced that sometimes things are just voodoo even when they should be completely logical. That's definitely the case at work on the Avid systems I use.
Here's the link to it:
http://androidfiles.org/ruu/?dir=Vigor
Click to expand...
Click to collapse
I did try wiping everything first. No luck. I will try the CleanWipe tomorrow, because right now, whatever my issues are, I'm being prevented from solving them since I can't S-OFF and I can't even seem to get a working ROM to make the phone worth having! Ugh.
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Flyhalf205 said:
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Click to expand...
Click to collapse
Oh yeah! Try that. Someone else was having trouble and did it that way and it worked. Here's instructions, just make sure you use PH98IMG and not whatever is used in the instructions since it was written up for a different phone.
http://androidforums.com/incredible-all-things-root/487280-easier-way-flash-pb31img-files.html
Also, once you get your phone back to stock make a nandroid as soon as you flash the recovery again so you'll have that to go back to if you have any more issues.
Flyhalf205 said:
And you can try installing it under fastboot oem ruu instead of the ph.zip file
Sent from my HTC Rezound...
Click to expand...
Click to collapse
Thank you, your magnanimity! Seriously, lol, you're gracing my thread just by being here. :victory:
feralicious said:
Oh yeah! Try that. Someone else was having trouble and did it that way and it worked. Here's instructions, just make sure you use PH98IMG and not whatever is used in the instructions since it was written up for a different phone.
http://androidforums.com/incredible-all-things-root/487280-easier-way-flash-pb31img-files.html
Also, once you get your phone back to stock make a nandroid as soon as you flash the recovery again so you'll have that to go back to if you have any more issues.
Click to expand...
Click to collapse
Thanks for the clicky, Feralicious. Same results, unfortunately. I'm going to try doing the RUU flash of Nils' ROM instead. Do you guys know where I can get the ICS firmware by itself? I cannot be sure that it's actually flashed right, unfortunately.
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Flyhalf205 said:
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Click to expand...
Click to collapse
I'll do that stuff and let you know. Thank you!
Yes, I am on 2.27 HBOOT.
Point of interest, though possibly unsurprising. When I send the lock command, it locks and reboots, but says "Failed" in my command window screen. Sure this is probably normal since the phone might just reboot before responding to the computer, but possibly an issue.
I believe that is the image I tried before, but I'll do it again both ways to be certain and report back soon! :good:
ncc74656m said:
Yes, I am on 2.27 HBOOT.
Point of interest, though possibly unsurprising. When I send the lock command, it locks and reboots, but says "Failed" in my command window screen. Sure this is probably normal since the phone might just reboot before responding to the computer, but possibly an issue.
I believe that is the image I tried before, but I'll do it again both ways to be certain and report back soon! :good:
Click to expand...
Click to collapse
My DNA said something about failing when I locked it. But it locked just fine.
Since it is failing.
fastboot oem rebootRUU
fastboot oem lock ----if unlocked
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
Should work Maybe
Flyhalf205 said:
Your HBOOT is 2.27 and it should say relocked????
It should since you flashed the 4.03.605.2 RUU. The only RUU you will be able to flash since your S-ON is the one found here http://www.androidfilehost.com/?fid=9390034591667978440
The other RUU will fail because you can't downgrade. So the link above(The Global RUU) will that fail or completely install 100%??
If it does install 100% and boot loops still. Take out the sdcard. Boot into the HBOOT and perform a factory reset inside of HBOOT/Fastboot(NOT IN RECOVERY)
Report your status
Click to expand...
Click to collapse
Ok, so, this part including a factory reset got me to "HTC Quietly Brilliant" screen, but then it bootloops again. Tried factory resetting again to no avail. Trying the second part.
Flyhalf205 said:
EDIT
The link listed above for the RUU. Other way of installing it which is a great way to look at the status of everything.
Boot into Fastboot
fastboot oem rebootRUU
fastboot oem lock
fastboot flash zip rezound_AndroidPolice_4.03.605.2_PH98IMG.zip
fastboot reboot
Click to expand...
Click to collapse
Same thing as before unfortunately. :/ Performed a factory reset afterwards to be safe - no go. Everything shows OK though in both this and the above install. *shrug*
Flyhalf205 said:
EDIT2:
If you can't get it installed or it did. Just go ahead and unlock again. Flash custom recovery. Install a rom. Flash the boot.img in fastboot. Factory reset. and then see if it boots. If still not working. hit me up on google chat [email protected]
Click to expand...
Click to collapse
Proceeding with another attempt at installing CM9, I guess. Maybe the first one got hosed. If I get it booting in any form, I'll Nandroid it before trying anything else.
ncc74656m said:
Proceeding with another attempt at installing CM9, I guess. Maybe the first one got hosed. If I get it booting in any form, I'll Nandroid it before trying anything else.
Click to expand...
Click to collapse
I really wouldn't see why you would need a Sense rom to get s-off. I would imagine it would just need su and busybox installed. But nandroid then try a sense rom again. Make sure you flash the boot.img through fastboot
I have a rezound that is now semi-broken. I've got Arman's recovery, but I can't seem to flash anything. I'm really hoping someone can help me out!
I have an hboot that says tampered, unlocked hboot,
VIGOR PVT SHIP S-ON RL
HBOOT-2.25.0000
RADIO-1.22.10.0421r/1.22.10.0424r
OpenDSP-v13.6.0.7611.00.0104
eMMC-boot
Apr 12, 2012 16:47:46
This whole thing is acting weird, and I've been working on it for a few hours. I can't seem to get a rom actually working. Maybe I'm not waiting enough, but I left it there for five minutes on the boot screen and it did nothing. I've tried both OTA superstock and Ecliptic, neither to any avail.
Fastboot is being a *****. I've tried everything I can to get fastboot to work, and it will not. It just simply wont work. So I'm hoping someone has some ideas, because I would really like to make sure this isn't my first real brick. plz <3
What commands are you using? And what files are you trying to flash?
Sent from my HTC Rezound using Xparent Skyblue Tapatalk 2
I can help you with Ecliptic, which should have just been a simple reboot to hboot after rom flash and then normal reboot. What exactly is occurring? Are you getting "mainver is older" error?
I've tried flashing both hboot_7230ddr2_Runnymede_1.28.0006_20120424 and supermisc - and at this point, I believe the partition tables are borked. I currently have amonra for the recovery, and now when I try and install zip from sdcard it gets all lame and says it cannot mount it. I think what needs to happen first is through ADB I need to find a way to flash a full RUU or something. It used to have 4.03 on it, so I know I'm not far away from success.
oh and at no point has flashboot oem lock ever worked. No Flashboot command has ever responded with anything. I have uninstalled all HTC drivers, removed Sense, and installed just the revolutionary drivers, and they still don't work.
Win 7 x64 -
If the phone boots to hboot fine you should be able to get the ph98img ruu for 605.12 and put that on your SD card and have it reflash your phone. It will fix partition problems as well. Can you try that and report back?
Sent from my ADR6425LVW using Tapatalk 2
@cellularticulate
Going by your info in post #4 it sounds like your trying to flash stuff meant for the Sensation XL. You can't do that, also to add you are s-on and if you try to load an eng hboot you WILL brick.
Run through this PH98IMG RUU in bootloader mode.
http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Snuzzo said:
@cellularticulate
Going by your info in post #4 it sounds like your trying to flash stuff meant for the Sensation XL. You can't do that, also to add you are s-on and if you try to load an eng hboot you WILL brick.
Run through this PH98IMG RUU in bootloader mode.
http://www.androidpolice.com/2012/0...cream-sandwich-ruu-for-final-ota-3-14-605-12/
Click to expand...
Click to collapse
And make sure you allow the RUU to complete, it will run through twice. It will go to a black screen for several seconds and then it will start over again. Make sure you don't interrupt it. Iirc, it will end up in bootloader when it's done, or maybe it reboots the phone.
It will only run through once, hboot and radio versions will match.
Sent from my ADR6425LVW using Xparent ICS Tapatalk 2
I need to fix the sd card permissions, I think. I will try flashing the RUU. I'm supposed to rename it and place it on my sdcard, and then just boot into hboot? It just...starts...automatically?
cellularticulate said:
I need to fix the sd card permissions, I think. I will try flashing the RUU. I'm supposed to rename it and place it on my sdcard, and then just boot into hboot? It just...starts...automatically?
Click to expand...
Click to collapse
If the ph98img is correct it (hboot) will detect it and prompt you to press up to start the update....
Sent from my Nexus 7 using Tapatalk HD
So I think I just realized why this has been a catastrophic failure this entire time. It's supposed to be on an EXTERNAL sd, right?
cellularticulate said:
So I think I just realized why this has been a catastrophic failure this entire time. It's supposed to be on an EXTERNAL sd, right?
Click to expand...
Click to collapse
Lol...yup...the small things get ya. Good luck finishing it up tonight. Finish ruu, unlock, flash custom recovery (I prefer the ph98img version of recoveries most of the time). Then load whatever ROM you want from recovery -or- continue rooting/setting up the stock ota ROM.
Sent from my Nexus 7 using Tapatalk HD
I still dont know why fastboot never worked :\ But yeah. That's literally all it was. The external SD card vs internal. I wish that was clarified somewhere. But I guess I know this going forward now!
I've got the RUU re-flashed, but I'm still stuck at the ecliptic boot screen. Ill try and do a fix permissions and see if that works.
cellularticulate said:
I've got the RUU re-flashed, but I'm still stuck at the ecliptic boot screen. Ill try and do a fix permissions and see if that works.
Click to expand...
Click to collapse
If you are stuck at the boot screen it's likely you don't have the correct kernel flashed for that rom. Did fastboot ever work for you? If not, do you have a ph98img version of the kernel for ecliptic? Snuzzo will probably chime in here shortly since i think that's his kernel...
I do not have a zip of his kernel, and fastboot still doesn't work. When I try and flash twrp and gives the mainver is old error, and I don't have time to fix this before work. Hopefully someone gives me golden advice and I can get this thing fixed. Three days now :\
Snuzzo, I know you don't do this specifically for money, but I will be donating to you. You've been a huge help.
you as well dottat.
One thing that's strange is I still think my partitions are messed up. I tried using the misctool to write an image to /sdcard2 and no matter what I tried, I couldn't find it. What's strange is when I'm in a shell, it shows this really, really weird login, and keeps kicking me OUT of the shell every couple of minutes. I'm going to try and switch back to TWRP since that what was on this phone when I got it. And yes, the phone was in working condition, things have just inherently gotten worse. http://puu.sh/2XtmZ.png
<3 y'all
OK what status are you at currently and why are you trying to flash that particular partition? Youre getting mainver is older? Hmmmm
You still got the latest twrp on here? If so, flash erez v9 then flash this
http://d-h.st/FZc
That's a dual purpose kernel zip. Do a fresh kernel flash with it. It should also set your mainver properly.
Sent from my Nexus 7 using Tapatalk HD
cellularticulate said:
I do not have a zip of his kernel, and fastboot still doesn't work. When I try and flash twrp and gives the mainver is old error, and I don't have time to fix this before work. Hopefully someone gives me golden advice and I can get this thing fixed. Three days now :\
Snuzzo, I know you don't do this specifically for money, but I will be donating to you. You've been a huge help.
you as well dottat.
One thing that's strange is I still think my partitions are messed up. I tried using the misctool to write an image to /sdcard2 and no matter what I tried, I couldn't find it. What's strange is when I'm in a shell, it shows this really, really weird login, and keeps kicking me OUT of the shell every couple of minutes. I'm going to try and switch back to TWRP since that what was on this phone when I got it. And yes, the phone was in working condition, things have just inherently gotten worse. http://puu.sh/2XtmZ.png
<3 y'all
Click to expand...
Click to collapse
If you let the RUU fun fully and you still have ecliptic boot screen showing you either didn't let the RUU fun fully or something really wonky is going on.. If you let the RUU run fully, you should have a stock rom booting by itself. Can we at least get to that point? We can probably get you around it. .but i would feel better starting from a fresh RUU.
Snuzzo said:
OK what status are you at currently and why are you trying to flash that particular partition? Youre getting mainver is older? Hmmmm
You still got the latest twrp on here? If so, flash erez v9 then flash this
http://d-h.st/FZc
That's a dual purpose kernel zip. Do a fresh kernel flash with it. It should also set your mainver properly.
Sent from my Nexus 7 using Tapatalk HD
Click to expand...
Click to collapse
@Snuzzo - what's erez v9? tried googling. Didn't see it in the guides on here either.
Hi,
I have a Sprint CDMA HTC EVO 3D. I tried root and get S-OFF for it. Unfortunately I failed and now the phone fail to boot.
Below is what I did from which you might be able to diagnose it and give me suggestions.
(1) The original status of mu phone is:
Stock rom, I never root it before.
HBOOT-1.58.0000
Android Version: 4.03
HTC Sense version: 3.6
Software version: 2.95.651.6.710RD
(2) My root procedures:
I followed this post: http://forum.xda-developers.com/showthread.php?t=1813818
I successfully unlocked phone with HTCDev, successfully Flashed 4EXT recovery, and successfully installed Superuser-3.1.3-arm-signed.zip. I also booted into sytem, everything worked well.
However I failed in next step of JuopunutBear's Wire Trick (S-OFF). When I ran ControlBear.exe, it finally hanged there.
Current status of my phone:
Unfortunately I did not make a backup to my original ROM, so there is no way to revert back by restoring backup.
Now the phone is in unlocked status, I was able to boot to HBOOT and also enter 4Ext recovery, however I am not able to boot into Android. If I try to boot into Android, it always hang at black screen.
I am able to boot to fastboot (USB) mode, I tried to flash some stock ROM (listed at http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209), but I failed. For example, I ran a RUU of 2.89.exe, it detected my phone version is 2.95, and further update RUU failed.
Looks like my partition is ruined, but I might be wrong.
ANyone can help me to restore my phone to working status? At least I need the phone to be able to boo to Android.
Here are also some tries that I ever did:
(1) I ever put the PG86IMG.zip file (downloaded from http://forum.xda-developers.com/showpost.php?p=21593454&postcount=564) to my sdcard, still failed.
(2) I ever formatted all partition from 4EXT recovery
lsdyna said:
Here are also some tries that I ever did:
(1) I ever put the PG86IMG.zip file (downloaded from http://forum.xda-developers.com/showpost.php?p=21593454&postcount=564) to my sdcard, still failed.
(2) I ever formatted all partition from 4EXT recovery
Click to expand...
Click to collapse
EDIT:
Okay. I've got some questions.
1. You're stuck on some black screen as you said. It boots past the white HTC splash and then it's stuck on that black screen, right. Do you mean the juopunutbear "arrow screen" - juopunutbears boot.img?
2. I think if you had flashed the original boot img everything would have been fine.
3. The easiest way is to flash to stock, so lets try to figure out why it doesn't flash.
MrJyrks said:
Okay. So from what I understood, you are stuck on the black juopunutbear screen, right?
Click to expand...
Click to collapse
Yes, after I was stuck with black juopunutbear screen, I took battery out, reboot again, never was able to root to Android. I am only able to boot to HBoot.
lsdyna said:
Yes, after I was stuck with black juopunutbear screen, I took battery out, reboot again, never was able to root to Android. I am only able to boot to HBoot.
Click to expand...
Click to collapse
And you can boot to recovery, right?
EDIT:
One more thing. Which ruu were you trying to run
Edit2:
What's your CID? Use "fastboot getvar cid" or "fastboot oem readcid" (without quotes).
Edit3:
BTW, this was on the wire trick page... http://unlimited.io/jbtroubleshooting.htm - TROUBLESHOOTING There was everything you needed to know when you failed at something. Remember that page. You may need it the next time you try to do the wiretrick.
Q: Were you using a linux distro for the wire trick and did you use the appropriate files for wire trick since GB and ICS have separate tools?
If you want I may assist you in gaining s-off if we get this thing functional again.
Yes, I am able to boot to recovery.
I tried ROM's here
http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209
and
http://forum.xda-developers.com/showthread.php?p=22519105#post22519105
I tried 2.17, 2.89, unfortunately none of them worked
My CID is SPCS_001
MrJyrks said:
And you can boot to recovery, right?
EDIT: One more thing. Which ruu were you trying to run
Edit2: What's your CID? Use "fastboot getvar cid" or "fastboot oem readcid" (without quotes).
Click to expand...
Click to collapse
lsdyna said:
Yes, I am able to boot to recovery.
I tried ROM's here
http://forum.xda-developers.com/showpost.php?p=24268786&postcount=209
and
http://forum.xda-developers.com/showthread.php?p=22519105#post22519105
I tried 2.17, 2.89, unfortunately none of them worked
My CID is SPCS_001
Click to expand...
Click to collapse
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Edit: This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Now I only want to revert my phone to stock, not considering root at present time.
I searched 2.95 ROM, unfortunately the highest version that I can find is 2.89. Does this mean I have no way to revert my phone to live? Thanks a lot.
MrJyrks said:
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Click to expand...
Click to collapse
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
MrJyrks said:
Aw man, I'm completely sorry I didn't see this: Software version: 2.95.651.6.710RD
That means, no RUU for you cause htc/sprint wasn't kind enough to provide the ruu. Also FYI you can't flash a ruu lower than your current one.
So your best bet is to flash the most stock 2.95 cdma rom you could find and right after, flash the stock cdma evo 3d kernel through fastboot or 4ext (I think 4ext smartflash does the same thing). Try to find something that's COMPLETELY STOCK - with no mods whatsoever or if you couldn't find any, try something that's almost* stock. That should get you booting and you can try s off again.
Click to expand...
Click to collapse
lsdyna said:
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
Click to expand...
Click to collapse
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
My HBoot screen shows below:
SHOOTER XC SHIP S-ON RL
HBOOT-1.58.000
RADIO-1.09.00.0108
OpenADSP-v02.6.0.2226.00.0217
DO you think I still have chance to save my device? Thanks a lot.
lsdyna said:
I ever run a RUU 1.13...exe for mmy phone, it said my device is having 1.000, and it tried to update to 1.13. However, the update procedure always failed at some point, some at beginning, some failed at 'wring signature'...
Click to expand...
Click to collapse
lsdyna said:
My HBoot screen shows below:
SHOOTER XC SHIP S-ON RL
HBOOT-1.58.000
RADIO-1.09.00.0108
OpenADSP-v02.6.0.2226.00.0217
DO you think I still have chance to save my device? Thanks a lot.
Click to expand...
Click to collapse
If you have access to the recovery, most likely, yes.
Hello MrJyrks,
Thank you so much for the link! I am eager to try that. Before I do that I think I shall ask two questions to avoid further mess up the device:
Question #1: To install the deodexed rom, which is the correct way:
(1) Rename the ZIP file to PG86IMG.ZIP, put to root of sdcard, then boot, letting the Bootloader to do the update.
(2) In 4EXT recovery, enable smartflash, enable script asserts, then install the zip from the root of sdcard.
Question #2: You said I shall flash boot image, can you tell me how to do this? I mean, where shall I get the boot image file? Flash it with 4EXT? SHall I do it before or after install ROM zip file?
Thank you very much for your helps!!!
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
I tried install the stock ROM from your link (using 4EXT with smartflash enabled and script asserts enabled.) . Amazing that installation completed successfully (indeed this is the first ROM zip that I was able to install successfully since I mess up the device). When I exit After that, it did some further update which I guess is the boot.img that you mentioned.
4EXT it said 'a pending update for your boot partition is detected' and I think it was doing the boot image flash that you mentioned, right?
Unfortunately when I boo the device, I still got black screen.
Now I am unlocked and also rooted (since I successfully installed superuser in 4EXT). DO you think I shall lock the devioce before installing the stock ROM? If so, one possible issue is that if I relock the device, I found 4EXT is not available. In that case, how shall I install the ROM zip file?
Thanks.
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
Further update:
I flashed boot image by: fastboot flash boot boot.img which is included in the stock ROM zip file.
The flash went successfully. However, I am still not able to boot to Android. WHat I have is the device hang there, alternatively displaying logo with white background, and black screen.
MrJyrks said:
This shall work. http://www.negalite.com/index.php?topic=21.0 Try it and report back!!!
Flash like a normal rom and don't forget to flash the boot img because that's what's really causing you problems right now. I'd choose the deodexed one from there.
Click to expand...
Click to collapse
I wiped cache and Dalvic, then re-flash the ROM, now I am able to boot as normal.
MrJyrks, you are my life save!!!
Your helps are sincerely appreciated !
lsdyna said:
I wiped cache and Dalvic, then re-flash the ROM, now I am able to boot as normal.
MrJyrks, you are my life save!!!
Your helps are sincerely appreciated !
Click to expand...
Click to collapse
You're welcome! I'm glad I could help!
---------- Post added at 12:02 PM ---------- Previous post was at 11:16 AM ----------
Oh, and if, in the future, you do try the wire trick and get stuck at some point you can revert the changes with ControlBear -r or ControlBear -f from command line. And you may also PM me if you need any help. Cheers!
MrJyrks, thank you so much!!!
MrJyrks said:
You're welcome! I'm glad I could help!
---------- Post added at 12:02 PM ---------- Previous post was at 11:16 AM ----------
Oh, and if, in the future, you do try the wire trick and get stuck at some point you can revert the changes with ControlBear -r or ControlBear -f from command line. And you may also PM me if you need any help. Cheers!
Click to expand...
Click to collapse
Similar problem, can't return to stock
I have a problem similar to lsdyna's, and am hoping that even though this post is old, MrJyrks or someone might be able to help me.
I am unsuccessfully trying to return my phone to stock. First a bit of history.
I had 2.95.651.6.710RD s-on hboot 1.58 Android Version: 4.03 HTC Sense version: 3.6 on my phone, and wanted root. I didn't need s-off, just wanted to root so could do some tweaking (stop some apps from autostarting, stop some form getting network access, etc.) so loaded 4EXT Recovery Touch, and got root (fastboot oem get_identifier_token method), got superuser in there, and happily began tweaking. Famous last words... I didn't make a backup right away (learned my lesson!) and suddenly found a 'overtweaked' sluggish phone on my hands.
Thought best thing would be to lose the root & return to stock & start over, carefully, making backups.
So I used Fastboot (fastboot oem lock) to lock it (worked) and proceeded to try to load RUU_Shooter_ICS_35_S_Sprint_WWE_2.89.651.2_Radio_1.09.00.0706__NV_NV_SPCS_1.43_release_271101_signed.exe into it [via my computer], but didn't realize until reading MrJyrks post that a lower RUU couldn't be used.
I now am relocked (phone does boot up, but can tell the system tweaks are still slogging it), lost the recovery, and wondering what to do... do I try putting recovery back in & using the Negalite 2.95 stock deodex ROM MrJyrks mentioned? If so, how do I use that zip file method verses the exe one I tried thru my computer?
Thanks for the help
You had issues with the RUU because your main version is higher than that contained in the RUU.
Unlock, flash recovery again. Boot into recovery and flash this zip: https://copy.com/wlVvwssXXNN00Pe
That will lower your main version. Relock the bootloader, put the phone into fastboot USB mode, then run the RUU while in fastboot USB mode.
Should be back to stock after that.