I have a issue where when i plug my charger in it doesnt do anything.. but if I bend the charger down it works fine. Do i need to bend the pin in the phone up with tweezers?
I read around where If you have this issue with the charging port then its gone. But my phone still charges fine. I dont want to go poking and bending and break something and it doesnt charge at all.
Just a little advice.
I have the rogers galaxy note I727r
Try a different cable first. They wear out and loosen quicker than the port. Do not go poking and bending or you will be replacing the usb component on the phone for sure.
Agoattamer said:
Try a different cable first. They wear out and loosen quicker than the port. Do not go poking and bending or you will be replacing the usb component on the phone for sure.
Click to expand...
Click to collapse
i tried 5 different cables and one of which is the official samsung cable... no dice.
It sounds as if you need a charge port repair .....but
Before the device goes out .....try this ....
With a very small and flat object .....you can slightly bend the outer edge of the charge port on the side that does not contain the joining seam, or break in the port ...
The slight bend will tighten the cable tip, as it slides into the port, and create a better contact patch...
But be careful !!!......as you can damage the port if you get too aggressive ....
The bend occurs on the long flat side of the device port ...opposite the port seam ....g
P.S.....Proceed at your own risk ....but it worked perfect for me ...g
Just remember, your phone is under warranty. Might just be better to let them take care of it. But if you get brave here is the part:
http://www.ebay.com/itm/New-Chargin...998?pt=LH_DefaultDomain_0&hash=item19d4f7ccbe
Not that difficult to get to either. There are a few videos on youtube for disassembly instructions.
Agoattamer said:
Just remember, your phone is under warranty. Might just be better to let them take care of it. But if you get brave here is the part:
http://www.ebay.com/itm/New-Chargin...998?pt=LH_DefaultDomain_0&hash=item19d4f7ccbe
Not that difficult to get to either. There are a few videos on youtube for disassembly instructions.
Click to expand...
Click to collapse
i boughtit as a used phone.. is there a picture that you can show the outer edge?
If you contact Samsung instead of ATT your warranty should be honored still. But it would be cheaper to buy the board and fix it yourself then to pay for shipping to a samsung repair center unless you have one nearby. I have no better pictures of the usb port.
Nor do I .....
If you hold the phone while looking into the charge port ...( screen up )....
The part you slightly bend is the bottom of the charge port ...
Don't pry against the case ....just slightly bend the bottom portion up .....with a small tipped object ..
A dull knife tip works well .....g
Yeah.. two mornings ago, I woke up to a phone in it's dying throes of battery life.. having been on the charger all night.
It's been a little touchy with certain cords for the past month or so but now, it doesn't matter which of the many available charger cords I have, from brand new to the original - none of them make the phone thing to charge or connect it via USB to a computer.
It's dead Jim.
Related
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
i have the same problem with my x10 but i have warranty but whilst i was waiting for them to collect it, i cut my usb lead up and stripped the black and red cables back obviously positive and negative and took the battery out and wedged each cable on the phone connector with the battery my battery had a plus and negative signs on it so was easy 2 work out, it charges the battery but it doesnt come up as charging on the phone it will still blind red lights but doesnt turn off, you have to keep and eye on the charging levels on the phone status do not let it go over 99% as this method dont tell the battery to stop charging, also this is not full proof and could break your x10 if not dont correctly,but as for your question the usb port does need to be soldered good luck
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
Hi John,
I fixed my friends USB port, you will need:
"helping hands" (a tool for holding small things with a magnifying glass)
0.5mm or 1mm Soldering iron
Hot glue
Under the magnifying glass, there you will see the 5 pins the usb port was solderded onto. You will need to put a little bit of solder onto each pin and onto the board.
Hold everything together with the helping hands, and just tick the soldering blobs with your iron. This will connect all the points. Do not solder for to long, or you will bridge pins or remove the solder.
Continue until all 5 is connected. Solder the 2 points on the side (holds the USB port, you could do this first if you don't have the helping hands)
plug in cable, use multimeter to see if there is current by you battery pins.
Voila.
If no power then you have to follow one of those fixes online where you have to bridge the doide and the V+ port.
Thanks for the info, like I said the phone is dead anyway, so I can't really make it any worse (That's what I keep telling myself anyway).
It the parts were a lot bigger, I probably wouldn't be bothered as much, but if I do get it wrong, I'm hoping I can take it off, remove the solder and just start again. (hopefully)
I think I have a good idea now of what I'm supposed to be doing, but I'll probably have to wait till I get a new soldering iron, as mine is a little bit too big.
Thanks ...John...
Hi guys,
So far I have used 3 chargers. A Verizon green 10ft long charger, the charger for my Nexus 7, and a Verizon car charger.
Basically when I plug any of these chargers in it will show it is charging for a split second, then it'll go away. So in order for it to charge, I have to push the charger in really hard, push it down, or bend it to the right. If I bend it to the right, when I let go, it stops charging. Sometimes I can get it at the right angle to keep it there, but I come back later and see that it isn't charger. Also if I push it in really hard, bending it to the right stops charging it.
The Verizon car charger has been the best for me (not as bad but I still have to bend it), but I use my nexus 7 charger for it most of the time.
This is super annoying, how it's real hard to get it to start charging and even harder to keep it. None of the pins on my chargers look crooked, nor inside my phone. I don't know if there is a fix for this, I might just take it to Verizon.
Anyone with the same problem or know of a fix out there? Thanks!
Hardware return to service centre .
This is I9300 forum advice / firmware from here may brick a non I9300 see sticky .
jje
I've had that problem to and with my fiancée's s3, I need to push it in quite hard to get it to start charging but my girlfriends s3 I need to do almost the exact same as what you've described bending it pushing it, I think we where on our 5th charger for hers before it just refused to charge anymore it is definitely a problem with the phone we sent hers back and it was fixed under warranty, we were told by T-Mobile that it was a common fault with the s3 but it was repaired and now works perfectly, we have the international models. The only fix is it to send it back unfortunately hope this helps.
jaggythistle said:
I've had that problem to and with my fiancée's s3, I need to push it in quite hard to get it to start charging but my girlfriends s3 I need to do almost the exact same as what you've described bending it pushing it, I think we where on our 5th charger for hers before it just refused to charge anymore it is definitely a problem with the phone we sent hers back and it was fixed under warranty, we were told by T-Mobile that it was a common fault with the s3 but it was repaired and now works perfectly, we have the international models. The only fix is it to send it back unfortunately hope this helps.
Click to expand...
Click to collapse
This is a Verizon certified phone. I only got it about a month ago. I'm a little scared to get a replacement. I actually had a Rezound before, and I went through 4 malfunctioning Rezounds and weeks of not having a phone before I called up verizon and they offered to switch my Rezound for a certified S3. It's great in all other ways, that's why I'm afraid to replace it with a phone that has problems with using the phone itself.
Okay, what is going on here. I made the cord tight and angled it to get a charge. It was at 42% last night when I started charging. I got up and the red light was still on, but the phone was still at 42%. It seems only angling to the right will it charge normally.
This is so annoying. So it's the charging port on my phone then? Maybe I should get the manufacturers charger, maybe I'm just using chargers not really compatible with my S3? Because my car charger works as soon as I plug it in. I mean if I turn in my car a lot it will stop charging and I will have to readjust the connection, but it's not nearly as bad as the charger I'm using at home.
Get it replaced and done with, mate. It's hardware problem. And not with the charger.
Sent from my GT-I9300 using xda app-developers app
jaggythistle said:
I've had that problem to and with my fiancée's s3, I need to push it in quite hard to get it to start charging but my girlfriends s3 I need to do almost the exact same as what you've described bending it pushing it, I think we where on our 5th charger for hers before it just refused to charge anymore it is definitely a problem with the phone we sent hers back and it was fixed under warranty, we were told by T-Mobile that it was a common fault with the s3 but it was repaired and now works perfectly, we have the international models. The only fix is it to send it back unfortunately hope this helps.
Click to expand...
Click to collapse
How long did it take for you to receive your phone back? I'm sending my phone to Samsung for repair. Sounds like it's going to take about 2 weeks, which is unfortunate. I just went through that
There is a simple fix!!!
I previously had to post this to a different forum so im posting the solution to this forum.
This issue can be fixed easily, you just have some stuff to fix it with. It's not only the connectors that's dirty, It's also the bottom of the micro usb port, it can easily be blocking the the connector from connecting all the way in. Here's how i fixed mine:
The first thing you'll need is some rubbing alcohol
Some Q-Tips.
The second thing you'll need is a very small sewing needle (go ask your grandma for one )
The third optional thing you'll need is some compressed air WITH a straw thing at the end
First off, remove the battery of the phone and set it somewhere.
Then get your sewing needle and dip it into the rubbing alcohol (helps clean the residue).
Then DELICATELY take the needle and clean ALL residue on the bottom of the port. Do this and make sure ALL residue is gone.
Then take the Q-tip and dip it in the rubbing alcohol.
VERY GENTLY take the Q-Tip and put very little pressure against the charging port.
Take the needle and go for a second try for the residue and let it air dry, OR get the compressed air and CAREFULLY blow out the rubbing alcohol and dust out of the charging port.
Put the battery when dry and turn on phone.
This will effectively clean the charging port AND the bottom of the port.
This has probably an 80% chance of working. It worked for me!
Plug it in and see if that works!
I'M NOT RESPONSIBLE IF YOU MESS UP AND SCREW UP YOUR PHONE!!!!!
I hope this helped everybody
yup face-palm he had his s3 in back pocket riding bicycle drunk home, fell off bike right on backside, phone taking most the impact.
the screen doesnt seem to be cracked just a small chip on the edge near camera.
he had it in a double sided leather padded case so we dunno how it got chipped
very small crack on body above usb port, but i think that crack is common.
the main point being the phone will now not switch on, is not charging or accessible via usb. no led nothing. button combo's do nothing. battery change no help
do you guys reckon it'll b worth replacing the usb port? or just a spares repo?
you can't replace the usb port unless you buy a motherboard, desolder one from there and solder it on your old one, which obviously doesn't make sense and won't work anyway, because the phone is clearly broken. The phone would switch on if the port was broken if there was any charge in the battery
Glebun said:
you can't replace the usb port unless you buy a motherboard, desolder one from there and solder it on your old one, which obviously doesn't make sense and won't work anyway, because the phone is clearly broken. The phone would switch on if the port was broken if there was any charge in the battery
Click to expand...
Click to collapse
well you can just buy the usb ports from part stores.
and yup i made another face-palm, its not the usb as a fully charged battery wont power it lol
im just gonna assume when he landed on it he just bent the motherboard and crushed something/many parts lol.
kinda strange he damaged the internal parts but not the screen.
he bought it like 6months ago so i doubt samsung or t-mobile will help eh.
oh well, what divv rides a bike with an s3 in theyre back pocket?
Before I begin, if there is already a thread outlining this particular problem, I apologize in advance.
Yesterday my Truesmart was in the charging cradle sitting on my desk, not realizing it, I accidentally opened a draw which pulled on the USB cable, dragging my Truesmart off of the desk and onto the floor. My truesmart fell about 2 feet and is fine, but the charging cradle will no longer charge it. I would assume that something broke in the cradle when it fell, which justifies the pathetic quality of it, although there is no visual damage on the cradle and when shaken nothing rattles around inside of the cradle.
My question is what should I do now? I am almost certain that it is the cradle that is the problem and not the Truesmart or the USB as the watch will still turn on and the USB will charge other devices. I have tried different power sources and different USBs and I only have one cradle. Is there anything I should troubleshoot in order to try and get the cradle working? Or is is possible that the problem is with the watch?
Any assistance would be greatly appreciated.
The spring contacts in the cradle may have gotten smushed in a bit by the impact. Try prying them up gently with like a needle.
Otherwise, the solders connecting the microUSB connector inside the cradle might have failed. They have been reported to be of poor quality on another owner's cradle with cold solders. Try resoldering them if probing them shows them not good connections anymore.
Thirdly, maybe your USB cable itself was damaged in the drop. Test it too.
Sent from my Nexus 5 using Tapatalk
I tried what you suggested with the needle and it didn't make any difference, they seem to be at the right position anyway.
I have a feeling it might be the solders, as it is possible that the sudden shock of the microUSB inside of the port caused something to break. Unfortunately I do not have any knowledge of soldering nor the equipment to do it. I wouldn't know how to open up the cradle without breaking it anyway.
I already tested the USB cable, it charges anything else, and I have tried other USBs with the Truesmart to make sure that it is infact the cradle.
I have sent Magan (may or may not have spelt her name right) two emails and have received no response.
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
I've been thinking of replacing the spring contacts with actual pogo pins. It's silly that the charger doesn't utilize them to begin with.
Sent from my GT-N5110 using Tapatalk
rhineymac said:
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
Click to expand...
Click to collapse
I am aware but I figured it was worth a shot since my order was missing a keychain that I was told would ship "soon".
I might look into taking it into a shop, how much did it cost you to do that? And I didn't understand your last sentence.
He mistyped "dollar store".
Apparently they have such cheap budget shops up in Canada too. I get my colored USB cables from them, they say, " Made in China" on them and generally last a couple of weeks.
Sent from my Nexus 5 using Tapatalk
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
rhineymac said:
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
Click to expand...
Click to collapse
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
SkyHawkTech said:
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Click to expand...
Click to collapse
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Agent. said:
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Click to expand...
Click to collapse
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
rhineymac said:
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
Click to expand...
Click to collapse
I'm pretty sure mine is the female USB port too, as my watch was plugged in when it fell so I assume the shock of the male USB caused it to break. Your guess is as good as mine as to if they ever plan on actually fulfilling their promises, they have done a pretty crummy job thus far. The charger is absolute junk, at least if we had the charging cable they initially promised we might be able to work with it a bit more.
trent999 said:
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
That isn't a bad idea for a temporary fix but the fact that it even comes down to doing something like that is absurd in my opinion, the charger should have been done and ready while they were dealing with all of the other BS issues.
Well, remember that for most owners the charging cradle they received works fine. It is not that poorly designed - mostly failures reported have been due to shoddy assembly. Similarly careless assembly has been reported on the watch itself in various areas.
I got my extra charger I ordered via Kickstarter, included in the package, but have never tested it nor needed to. I also figured out a way to charge the spare battery with an Anker universal charger, just in case. That charger came free with a couple of VGNexus batteries I bought from Amazon.
You might have better luck with the USB port repair staying fixed if you support its attachment to the board, such as it is, with an application of SuperGlue prior to resoldering the connections.
Holding a cable connector in place via only the contact solders would always be a bad design though.
Sent from my Nexus 7 using Tapatalk
Hi All,
I have a Nokia 7.1 that stopped charging. I cleaned out the charge port and tried different cables and adapters but nothing worked. I've since come to find out that it's a common enough problem that lots of people post about it on Nokia's support forum with no other option other than taking it to a service center. I'm in the USA and there's not a single service center in my state so I decided to try and replace the daughter board myself. I've done this kind of thing before on other phones, my Nexus 4 was a frankenstein's monster by the time I was done with it.
My problem is I can't find a reliable source for a quality part. There's tons of replacements on amazon, ebay, aliexpress and other random sites but all the ones I've read had issues for connectivity of cell service or wifi. Does anyone know where I can source a new daughter board for this phone?
Any help is greatly appreciated.
Thanks!!
I went through the same issue.
Bought another type c charging port on Amazon, it still works.
Awesome! Thanks for the reply. Did you go with one of the ~$10 ones or one of the ~$20 ones?
My 7.1 developed the same problem. What is the root cause? Is it mechanical problem of the connector pins worn out/oxidized? It does seem to be a mechanical problem since I can still wiggle the cable to make it charge for a while. What puzzles me is that the USB-C has inherent redundancy with 4 power and 4 ground pins that it should not easily fail. I have a phone with the old micro-USB and the charging still works flawlessly.
lejaune said:
My 7.1 developed the same problem. What is the root cause? Is it mechanical problem of the connector pins worn out/oxidized? It does seem to be a mechanical problem since I can still wiggle the cable to make it charge for a while. What puzzles me is that the USB-C has inherent redundancy with 4 power and 4 ground pins that it should not easily fail. I have a phone with the old micro-USB and the charging still works flawlessly.
Click to expand...
Click to collapse
I'm not sure. It does seem to be a mechanical problem, but I've seen some repair videos where they open it up and just run a soldering iron over the connector pins on the board and it starts working again. I've ordered a daughter board and a replacement back glass panel in case I break it trying to get it off. I'll update after I get the parts and open it up to see if it works.
The board I ordered was this one from Amazon Smile:
https://smile.amazon.com/gp/product/B08166DLDC/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
It seems like the ~$10 boards are missing some chips that the ~$20 ones have, at least according to the pictures that were uploaded with the listing.
@bpowdhar, Thanks for the quick reply. I did order a connector board on Ebay, and it looks to be of the ~$10 variety. I'll see how it works when it gets here. I will also try the "melting the solder" trick without removing the connector first. If that works, I'll leave the old board in place just to minimize the risk.
So I received the USB-C charging board and replaced the bad one. Now, it seems to be charging normally. It took some work to open the back cover by heating to soften the glue/tape around the edge. I then used an a xacto knife to pry the corner open followed by dragging an old credit card to slowly separate the cover. Once it's open, everything went smoothly. Just watch one of several Youtube video clips to know what to expect. You do need a small Philips screwdriver and a #5 Torx driver. You need to lift a ribbon cable and a micro coax cable from the board. Just don't forget to put them back on to the new board. I didn't bother to fix the old board by re-solder the connector pins because they are way too small for my solder iron.
I rely on the existing glue/tape to glue the cover back, but I'm sure it's not as water/dust proof as before, so I may redo that part to clean the old tape out and use the new tape or glue when I have more time.
I do noticed a couple of parts missing on my $9 board. I don't know if they have anything to do with regulating the high voltage fast charging. I usually charge the phone with a 5V adapter, and I will stick to 5V, at least for now.
Thanks for the update! I'm still waiting for my board to arrive from Amazon. It was delayed with the new shipping date anywhere from Nov 5 - Nov 10 and it still hasn't arrived. It sucks because tracking info shows that it arrived at my area's sorting facility on Oct 29 and left it on Nov 4. So it should have only taken a day or two to get to my local post office and to my house. I'll update when it finally gets here.
I know it's been a couple of months, but I finally got the part and swapped it out yesterday. The battery was completely dead so I plugged it in to charge and left for the day. I came back to it this morning and it's at 100% battery! I'm so happy now! I've attached a couple of pictures showing the old board (with the red dot) and the new one. So far no connectivity issues, but I'll give it a couple of weeks to see if anything changes.
A couple other notes:
It was surprisingly easy to get the back glass off. I used a heat gun on low and ran it around the perimeter for a couple of minutes and a utility knife to cut the adhesive. This part was what I was most apprehensive about tackling.
The fingerprint sensor comes off the same way, apply heat and press / pry away from the glass to reuse.
If I had to do it again, I'd buy the tube of sealant. The replacement glass came with a set of narrow adhesive strips and those were a pain to deal with.
Thanks to everyone who contributed to the thread. Hopefully this helps someone else.