Related
I was using the MIUI rom and I sold the phone. To deliver to the buyer I decided to go back to the stock rom but forgot to wipe and now I have the following situation:
- I can only get into download mode
- Odin recognizes the phone
- I tried to repartition the Odin reported successful operation (my model is 16gb)
- Tried to put other roms on the phone including those downloaded from the site sammobile, selecting only auto-reboot and f.reset.time
- With these steps could only get stuck in "nand write start ..."
- Tried installing kies but do not believe it can be something with the drivers because the odin recognizes the phone.
I read many posts but after two days decedi post to see if anyone would help me solve this issue
I'll be waiting for directions on how to proceed without worsening the scenario.
Odin log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBBLG2_I9300VILG1_I9300ZVVBLG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> modem.bin
<ID:0/006> NAND Write Start!!
have you tried restarting your computer or using another computer? or even a different usb port or cable?
ages ago I had a similar problem - never moved beyond the start point - simple restart solved it for me...no idea if that's the same situation as you.
Just throwing out ideas here; otherwise I'm not sure.
Sent from my GT-I9300 using Tapatalk 2
Tried to do this, but still stucked at nand write start...
One thing I noticed is that the progress bar on the phone at the "downloading mode screen" runs quickly, and then it stops at nand write start.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBBLG2_I9300VILG1_I9300ZVVBLG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> modem.bin
<ID:0/005> NAND Write Start!!
At least I'm not alone
I have the exact same problem you have. Intl i9300, cannot enter recovery, only download mode. Flashing 16gb pit file works ok, however attempting to flash Stock rom gets stuck at Nand Write Start. Not sure what to do now, I guess I'll wait for responses here as well.
RePartition .
Fail Nand write .
Assuming you have read and are following the basics re an Odin flash ( if not go and read them ) .
This sounds in both cases like a damaged Nand >>> service centre job .
jje
I've not done much to my S3. Trouble started when I decided to install an OTA of Foxhound 1.8. Installation completed successfully but during the application upgrade (...you know the first boot message of 'Android is updating x of 365 apps). It froze and stuck there for like 15min so I decided to reboot it and all hell broke loose.
Started with 'Foxhound cannot mount recovery command..' etc. Which made me decide to flash my 16gb pit file, and since then all attempts to flash back to stock stall at 'Nand write start'.
I have backups of everything, even my efs. Problem is I can't even get to recovery to restore anything.
I'll keep trying I guess, worst case I'll just return it back to Samsung.
pull usb devices except s3 and be sure to have correct drivers then try again. you may even try it on another pc of course with installing drivers. if none of them works try flashing a kernel or recovery if it flashes then try to flash stock rom.if stucks again at nand write there may be a problem at emmc sect. but dont worry just do what i said if it fails there should be a solution
if you can enter the recovery mode u should be happy
to kamau can u send me the pit file you flashed thanks
zhjackss said:
to kamau can u send me the pit file you flashed thanks
Click to expand...
Click to collapse
There it is. I"m now working on resetting the flash counter from odin since I obviously can't install triangle away in preparation of returning it to samsung.
Hello everyone,
I am not sure whether this is the right place for my question but my Galaxy S II stopped working and I was wondering if anyone might help me?
I tried updating the FW from 2.3 to 4.0 (I'm guessing) through Kies and after about 45 minutes of seeing both screens (PC and Phone) unchanged, I ended up removing the phone. Next, Kies suggested an "Emergency Firmware thingy" (it said it in German so I wouldn't really know how to translate it). Tried again, after 45 minutes gave up once more.
Since then, I downloaded ODIN and tried to follow instructions I found online to flash it (first I tried with Ice-Cream, then with Gingerbread).
Ever since I removed it from Kies, it would only show a phone connected to a PC with a yellow warning triangle in the middle. Whenevery I use the Volume-Menu-Power button, the warning on changing the OS appears and then, when I press "volume up", it shows the green android in the middle and tells me it's downloading and not to turn off the device, though there is no downloading progress.
When I try with ODIN, ODIN recognizes the device on both USB ports - I found md5 files for Germany but every time I start it the Message window says:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLA4_I9100VIAKI1_I9100XXKI4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cache.img
and doesn'tget any farther than "cache.img".
I am at a complete loss as to what to do or try. I have had this phone for a year now, this is the first time I tried to update with Kies - the phone had not been rooted or anything else. The phone has no simlock (I don't know if any other information is relevant).
Any ideas or has my phone thus become the infamous brick? *pleasenopleasenopleaseno*
Thanks in advance for your time and patience - in case I've overread a thread with this exact same problems, I apologize and would appreciate if someone could re-direct me. I've already spent so much time looking for solutions, my concentration may have suffered.
Best wishes,
Junivere
Before flashing with Odin, did you kill all Kies processes from Windows task manager? If not, do that and then start flash.
Edit: And since you can access download mode, its not bricked...so you can relax
Sent from my GT-N7100 using Tapatalk 2
I9100?
Flash JB.
And try an older ODIN version.
And check kies like the above poster suggested.
Other usb port/usb cable might do the work too.
Sent from the little guy
Thanks for the replies!!!
I stopped all the Kies processes over the task manager before (was that enough?) and tried from both USB ports of my laptop (006 and 007 I guess) with equal results.
I used Odin3 v1.85 - is that too old or too new? Which version should I try?
And I am sooooooooo relieved it's not a brick!!!
Thanks again!
kinda old, try 1.3 or 3.x
And flash siyah v5 just for kicks.
Sent from the little guy
I tried again and I'll try to explain step by step, ok? Maybe you notice something I did wrong?
I killed all the Kies processes in the task manager like before.
I downloaded Odin 3 v.07 and started it. I had "Auto reboot" and "F.Reset time" checked and clicked on "PDA" to add the *.md5 file with the firmware.
I started the phone in the download mode and connected it to the PC, Odin recognized it alright.
I started and the first time, with the USB port in front, it stopped at "cache.img" in the message window.
I tried a different FW file and the other USB port further back and for the first time the phone shows a tiny bit of blue in the progress underneath "Downloading..." but in Odin it is now stuck at "factoryfs.img" for the last ten minutes,
The entire message window says this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLA4_I9100VIAKI1_I9100XXKI4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cache.img
<ID:0/007> factoryfs.img
Any ideas???
Best wishes and thanks again!!!
Flash siyah V5.
Sent from the little guy
How do I do that? I tried to find an instruction in the XDA forum in the 15 minutes I have between posts but couldn't find anything.
Junivere83 said:
How do I do that? I tried to find an instruction in the XDA forum in the 15 minutes I have between posts but couldn't find anything.
Click to expand...
Click to collapse
gokhanmoral.com
Siyah v5 for SII.
Put it on PDA, press start and flash away.
Sent from the little guy
Ok, so now I am starting to get slightly terrified:
When trying to flash Siyah 5 (Siyah-s2-v5.0.1), it stops there:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> zImage
:crying:
Keep trying, you'll come around.
Another usb cable could help.
Another pc would as well.
Sent from the little guy
Ok, so the Sivyah v5 flash worked when I tried Odin3 v1.3 but I'm still battling with the actual firmware.
Thanks for your help so far, though - I'm really greatful and I'll keep trying.
My mission for today will be finding someone's cable and PC to borrow...
I'll keep you posted, though!
Wow, you are the bestest ever!!!
With a netbook (OS Windows 7) I eventually managed the flash - now I'm reconfiguring everything. I am sooooo relieved!!!!
I have one last question (sorry for being so naive!), though:
Is it still possible with a flashed phone (with the Sivya thing on it) to use Kies to try and update or do automatic updates or do I have to flash all the newer firmware?
Best wishes,
Junivere
Junivere83 said:
Wow, you are the bestest ever!!!
With a netbook (OS Windows 7) I eventually managed the flash - now I'm reconfiguring everything. I am sooooo relieved!!!!
I have one last question (sorry for being so naive!), though:
Is it still possible with a flashed phone (with the Sivya thing on it) to use Kies to try and update or do automatic updates or do I have to flash all the newer firmware?
Best wishes,
Junivere
Click to expand...
Click to collapse
Depends on what ROM you are flashing.
For instance, if you flash LS8 you'll get a 22 mb update to get you to LSD.
I would flash LSD straight up tho.
If you don't want a headache with odin no more, feel free to try Mobile Odin, it will perform all the flashing for you.
Sent from the little guy
I rooted my phone about 1.5 years ago when I got it. I remember I installed a custom ROM (can't remember which right now for sure - possibly omega?) and kernel (siyah) .. I'm not sure if that matters? I know I had clockworkmod installed.
Phone's worked fine for ages. Today it randomly crashed playing a youtube video and got stuck in a boot loop. On a couple of occasions it came up with a welcome/start screen as if it was a brand new stock s3 but then booted again.
It kept coming up with the b&w samsung galaxy s3. That's it, it'd sometimes turn off and on, same thing again.
I can't get it to go into recovery mode. It happened once or twice very briefly, but then just rebooted again.
I got it in download mode. I tried recovering using KIES but it failed. Tried using ODIN and a stock s3 ROM and it failed. Tried using ODIN with a "nowipe" root ROM and odin hung.
Now if I try to turn it on without download mode it just says "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
Can anyone give me any suggestions/help? Am I screwed, is it permanently bricked?
jeemer said:
I rooted my phone about 1.5 years ago when I got it. I remember I installed a custom ROM (can't remember which right now for sure - possibly omega?) and kernel (siyah) .. I'm not sure if that matters? I know I had clockworkmod installed.
Phone's worked fine for ages. Today it randomly crashed playing a youtube video and got stuck in a boot loop. On a couple of occasions it came up with a welcome/start screen as if it was a brand new stock s3 but then booted again.
It kept coming up with the b&w samsung galaxy s3. That's it, it'd sometimes turn off and on, same thing again.
I can't get it to go into recovery mode. It happened once or twice very briefly, but then just rebooted again.
I got it in download mode. I tried recovering using KIES but it failed. Tried using ODIN and a stock s3 ROM and it failed. Tried using ODIN with a "nowipe" root ROM and odin hung.
Now if I try to turn it on without download mode it just says "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
Can anyone give me any suggestions/help? Am I screwed, is it permanently bricked?
Click to expand...
Click to collapse
have a look here, maybe same challenge you are facing (I just flew over the thread).
I tried a few other things since.
Using Odin I tried flashing a stock ROM, after ending the Kies process and using a different USB. It all said it had worked, gave me a boot screen and said android is upgrading - optimising apps. It hung doing this at 10 of 70 or something. I tried resetting and it hung at 5 of 70, and when i reset again it just wouldn't get past that.
Tried flashing with a more recent stock ROM using Odin 1.3 as above, but it hung at system.img
Tried flashing with the more recent stock ROM using the latest Odin. The blue bar counted right up to full on my screen, then the phone reset.
It was sitting with the little 3d android character with the spinning 3d mesh sphere in his stomach. A blue line started counting up but has frozen about maybe 25% of the way along. After a short while Odin said PASS! and it all seems to have completed according to Odin
The android graphic was still spinning but nothing else was happening, the blue line would not progress any further.
After a few minutes the phone screen went black, and came up with the black and white Samsung Galaxy SIII screen for a second or so. Then it just went black again.
Here is the Odin log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELL4_I9300O2UELL1_I9300BWELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
When I turn it on now the same thing happens - the black and white Samsung Galaxy SIII screen comes on for a second or so and then the screen goes black.
If I try and put it in recovery mode the same thing happens. If I try to put it in download mode, that works.
Am I right in thinking I still have a hope to save it here since Odin still sees it? What do I try now? :/
http://forum.xda-developers.com/showthread.php?t=1840030
this is the only other suggestion I've found so far and it seems quite scary!
Flash a full stock rom using latest odin, immediately boot into recovery and factory reset.
Because you left the phone for so long on a firmware that was not SDS safe you may have nand memory damage, even if the file structure is still intact.
Sent from my GT-I9300 using Tapatalk
I tried doing a full flash again with the older stock firmware I started with. Got right through the whole process again, says it passed and it hung at the Android guy with the spinning mesh sphere.
I've never managed to get it into recovery mode since i got it in clockwork recovery mode a couple of occasions last night and it reset each time
Any suggestions as to what I could try to get it past this stage?
If it looks like I have nand memory damage would it be worth trying what's in that "scary" link i posted? :/
I tried flashing again to see if I could instantly get it into recovery and it failed for the first time
Here is the log
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXDLIH_I9300O2UDLI3_I9300BWDLI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELL4_I9300O2UELL1_I9300BWELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm guessing this is a nand issue then? Is my only option at that point the link above (http://forum.xda-developers.com/showthread.php?t=1840030) ?
really don't get it.. tried it again and this time the whole process passed according to odin
same again though, android guy with spinning mesh... nothing for a while
phone eventually goes black, resets, samsung galaxy s3 in black and white. goes black. if i leave it for a while that screen will come up again, then it'll go black etc.
do i bite the bullet and try that method that involves nand reset all? please advise i'm in a bit of a pickle here as i'm in the middle of interviewing for jobs so i could use my phone.. do need to try and fix this asap if i can...
You can try flashing the rescue firmware, search in general forum, but if that doesn't work then you need a new motherboard.
Sent from my GT-I9300 using Tapatalk
ok - that seems to be this one for the s3 - http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
that look right?
downloading now. fingers crossed, thanks for your help i really do appreciate it.
Title says it all.
I tried to boot into recovery menu to look at something but that failed. I connected my GS II to odin re install the firmware but odin stalled. I had to kill odin with Task manager. Before odin, my phone would go to the download recovery menu. Now I cannot get it to respond at all.
Did odin not responding and me killing odin via TM hard brick my phone?
lol. A Courts-Martial started today for an old neighbor of mine and I was supposed to testify but they never called me (until my phone broke). My company commander tried to call me but couldn't get me. He called my NCOIC so my NCOIC tried to call me. Nope. NCOIC called one of the guys near me and told him to see if I was still alive.
lol.
Odin failing to complete the flash would not usually hard brick the phone. Usually after a failed flash, you can still get into download mode and flash again. If the flash was interrupted while Odin was loading the boot loader, then you would get a hard brick, but the boot loader goes on in in a matter of seconds, so the exposure is small.
Don't know what would cause the phone to be completely unresponsive, but if you can't get it into download mode, then your options are limited. You could send it out for jtag repair but that would probably cost around $50 to $60. If you decide to go that route, Mobile Tech Videos is a trusted and respected shop.
Wife's phone is done, at least I am done with it. She can pick from a GS3 mini or GS4 mini. I bricked mine while working on hers.
Mine is off to mobile tech videos. I should get it back next week. Wife gets a new phone, I will keep my SII.
svtfast said:
Wife's phone is done, at least I am done with it. She can pick from a GS3 mini or GS4 mini. I bricked mine while working on hers.
Mine is off to mobile tech videos. I should get it back next week. Wife gets a new phone, I will keep my SII.
Click to expand...
Click to collapse
The SIII mini is still lower-end than the S2. :b
Stuck as well
I keep trying to flash CWM recovery tar file with Odin because I cant seem to get passed the start up logo with the big S in the middle and I keep getting this issue:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ODINRecovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone could help or if anyone could point to someone that could help me I will be forever in you debt.
It was bricked. Send it to mobiletechvidoes and got it back. Working like new!
Rooted and CWM installed. ShoStock rom installed but ended up in bootloop. Reinstalling now.
d27redux said:
I keep trying to flash CWM recovery tar file with Odin because I cant seem to get passed the start up logo with the big S in the middle and I keep getting this issue:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ODINRecovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone could help or if anyone could point to someone that could help me I will be forever in you debt.
Click to expand...
Click to collapse
Why did you post in this thread? You should start your own thread for a new issue.
Do you have SGH-I777, or is it SGH-S959G, or some other model? If I777, you can't flash a separate recovery. Recovery is built in to the kernel, so you have to flash a kernel to get CWM.
Please study and know what you are doing before you damage your phone.
Hello
For a couple of weeks now, i've been trying to fix this phone for a friend who studies as an artist. She wanted the Galaxy Beam for presentations and bought one used as they seemingly ain't to be found in the stores any longer.
Originally, the firmware ends at 2.3.6 on this brand, but this one was rooted to be fit with 4.1.2.
The phone bugged and hung in weird ways, so i thought to follow the steps into downgrading it to stock rom for her and see if that would help.
I am no expert, but since i have successfully rooted several phones and tablets earlier with no issues (its pretty straight forward when it works, right), i felt up for the tast.
I have spent a lot of time googling the last couple weeks, and reading a lot of solutions here on these forums, but i can't seem to find this ecact problem, so here goes.
Samsung Galaxy Beam GT.I8530
Odin3 v3.07
Windows 7 and 8 fully updated (tried both)
No matter which Android version i chose, it ends up at the same spot. Stuck at logo screen after first boot.
I have tried both with and without a PIT file, same result.
This last try was with a PIT and Android 4.1.2. (i understand that PIT is not nessessary, as it should be baked within the PDA if it's a single file, but what won't you try eventually, right?)
Load Odin, admin rights
Boot phone in download mode
Insert USB
-->
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8530DXLJ1_I8530OLBLJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.img.md5
<ID:0/003> NAND Write Start!!
<ID:0/003> hidden.img.md5
<ID:0/003> kernel.bin.md5
<ID:0/003> modem.bin.md5
<ID:0/003> system.img.md5
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
- here, the phone reboots and loads to logo screen *
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
- from here the phone wont nudge from the logo screen. can reboot, nothing new happens.
No other functions work, other than:
- volume down+home+power (download mode)
- power (boots to logo screen)
Thanks for reading! Hope someone feels up for the task
Edit: It might be vital information that the phone will uncharge the battery at logo screen eventually, even when connected to a computer. (5v output) But i believe this is common somehow.
Also, if i try and shut down the phone, it will reboot into a frozen "star icon".
Bump*
What makes this issue differ from others i've read on these forums, is this:
Akiiras said:
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Any theories?
As much as i hate bumping, i'm feeling kind of responsible to try and fix it. Hope someone got a clue on what might be wrong. Thanks
"I bet you 10 buck you'll get your answer here within a couple days" -a friend said, well, in norwegian though.
I guess a week later and no response means that i've at least earned 10 buck! ^^
Guess i can give it one more shot here before i send it to a repair guy.
*bump*
Akiiras said:
Guess i can give it one more shot here before i send it to a repair guy.
*bump*
Click to expand...
Click to collapse
Are you sure about the right region when choosing a firmware? Did you also try Odin 1.85? Have you tried flash a custom recovery via Odin and flash a rom manually?
LS.xD said:
Are you sure about the right region when choosing a firmware? Did you also try Odin 1.85? Have you tried flash a custom recovery via Odin and flash a rom manually?
Click to expand...
Click to collapse
Hi, and thanks for the reply!
I am pretty sure i got the right firmware region. At least, the only region that covered my location (norway) that i could find, was nordic.
I have not tried Odin v1.85 or manually. I guess i can find a guide on how to do it manually here somewhere, but i'll go for a shot with the older version of Odin right away.
Thanks!
Akiiras said:
Hi, and thanks for the reply!
I am pretty sure i got the right firmware region. At least, the only region that covered my location (norway) that i could find, was nordic.
I have not tried Odin v1.85 or manually. I guess i can find a guide on how to do it manually here somewhere, but i'll go for a shot with the older version of Odin right away.
Thanks!
Click to expand...
Click to collapse
BTW there are 4 different versions for nodric countries --> LINK
Odin3 v1.85 didn't work. Well, in the sense that it probably does a job well done and says everything went well, but the phone wont nudge past boot screen.
I'll see if i can learn how to do it manually and come back with the result.
Edit:
LS.xD said:
BTW there are 4 different versions for nodric countries --> LINK
Click to expand...
Click to collapse
Oh, thanks! I couldnt find it at sammobile myself, so i found it somewhere else. This could be it!
any developments?
I Have the Same Problem
I Have the same problem please anyone help me!!!!!
SOLUTION
Akiiras said:
Hello
For a couple of weeks now, i've been trying to fix this phone for a friend who studies as an artist. She wanted the Galaxy Beam for presentations and bought one used as they seemingly ain't to be found in the stores any longer.
Originally, the firmware ends at 2.3.6 on this brand, but this one was rooted to be fit with 4.1.2.
The phone bugged and hung in weird ways, so i thought to follow the steps into downgrading it to stock rom for her and see if that would help.
I am no expert, but since i have successfully rooted several phones and tablets earlier with no issues (its pretty straight forward when it works, right), i felt up for the tast.
I have spent a lot of time googling the last couple weeks, and reading a lot of solutions here on these forums, but i can't seem to find this ecact problem, so here goes.
Samsung Galaxy Beam GT.I8530
Odin3 v3.07
Windows 7 and 8 fully updated (tried both)
No matter which Android version i chose, it ends up at the same spot. Stuck at logo screen after first boot.
I have tried both with and without a PIT file, same result.
This last try was with a PIT and Android 4.1.2. (i understand that PIT is not nessessary, as it should be baked within the PDA if it's a single file, but what won't you try eventually, right?)
Load Odin, admin rights
Boot phone in download mode
Insert USB
-->
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8530DXLJ1_I8530OLBLJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.img.md5
<ID:0/003> NAND Write Start!!
<ID:0/003> hidden.img.md5
<ID:0/003> kernel.bin.md5
<ID:0/003> modem.bin.md5
<ID:0/003> system.img.md5
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
- here, the phone reboots and loads to logo screen *
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
- from here the phone wont nudge from the logo screen. can reboot, nothing new happens.
No other functions work, other than:
- volume down+home+power (download mode)
- power (boots to logo screen)
Thanks for reading! Hope someone feels up for the task
Edit: It might be vital information that the phone will uncharge the battery at logo screen eventually, even when connected to a computer. (5v output) But i believe this is common somehow.
Also, if i try and shut down the phone, it will reboot into a frozen "star icon".
Click to expand...
Click to collapse
I have The solution For that remove your battery and charge battery by use of another working mobile or battery charger box
after charging you do the flashing using android 4.1.2
it successfully works on my mobile
the problem is battery is low so that at the time of flashing it turned off ....so fill the battery and use......