[Q] Flashing gone wrong - now won't accept (most) flashing..? - Motorola Droid RAZR

Hi, I unfortunately don't know a lot about what I am doing here (the root of all my trouble), I'll try to get the info straight:
Motorola Droid Razr (XT910), bought in Dubai, using it in UK, so I didn't receive OTA updates. I decided to try update to ICS using RSD Lite, but the flashing got stuck at system_signed. I gave it a lot of time (hours) before I switched off the phone and tried again, which is when things started going haywire:
During my following attempts, the battery ran low, so I couldn't go on trying (soft brick). I made a patched "factory cable" as per instructions in this forum somewhere, the cable works and powers the phone for flashing.
Now all it does is coming up with the fastboot screen, which reads:
AP Fastboot Flash Mode (S) (Flash Failure)
0A.6C
[...]
Device is LOCKED. Status code: 0
Battery OK
OK to Program
Transfer Mode:
USB Connected
...which suggests to me it would be ok to be flashed, if only I could get it to accept the files. Being a big numpty, I am unfortunately not quite sure what was the exact version that was on there before (big mistake, I know that now), it was 2.3.6 and I suspect it must have been a MEA version, since it was bought there(? - also, when I first switched it on, all was in arabic).
What I have tried so far was:
* using several different fastboot firmware files with RSD Lite 5.7, all of which do not get over the step '1/xx flash cdt.bin "cdt.bin_signed"' - it just hangs supposedly "In process..." forever. I noticed all of these have an "ota" folder (although they vary considerably in size between <1 and 2.5 GB) - maybe all the ones I downloaded are only updates? Is there an actual, base operating system image somewhere?
After many failed attempts, I got desperate and tried files for different regions at random. The ones I tried so far:
SPDREM_U_01.6.5.1-73_SPU-11-M1-2_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml
SPDREM_U_01.6.5.1-73_SPU-11-M1-2-ULB_1C.85P_0A.6B_DATDE_CFC_HWp2b_SIGNED.xml
SPDREM_U_01.6.5.1-167_SPU-15-M2-3_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b_Service1FF_fastboot.xml
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot.xml
SPYDERIRD_U.01.26.0_SPD-IRD-21_SIGN_ASIA_RETAIL_HKTW.xml
SPYDERIRD_U.01.26.0_SPD-IRD-21_SIGN_MEA_RETAIL.xml
The only thing I am quite sure about is that it is not LATAM.
* I tried manually flashing the various image files with moto-fastboot, fastboot, and eprj-mfastboot, both the Windows and the Linux versions, with pretty much always the same result: it would flash some files (e.g. ebr, mbr, devtree), but not what I think are the crucial ones: boot, system, also logo.bin. As there are so many possible combinations, I have not tried every file from every firmware I downloaded with every possible program, but as far as I can tell, the results were the same. I did get some error messages about signing (indicating wrong region) sometimes, but most of the time it just hangs forever while supposedly transferring the files.
* I also tried the DroidRAZRUtility, both 1.51 and 1.6, which both invariably fail at the first step of flashing the "allow-mbmloader-flashing-mbm.bin" file on there.
So, I am out of ideas now. Please, someone tell me I have overlooked something obvious. Also, please tell me I haven't bricked the thing for good.
Is there not a way to write something new into it's memory on an even more basic level (I am thinking Linux' dd here), or to read out which region it is currently locked to? I repeat, all I get is the Fastboot screen, I can get into the Fastboot menu, but none of the options gets me anywhere else, (stock) recovery does not work... My last idea is that it might still be a power issue despite the "factory cable", and to try and crack it open and power it at the battery contacts for flashing - but the fact that some flashing works, and the other files don't fail because it goes dead, but because it rejects them, suggests to me it is not a power problem.
Any suggestions appreciated, thanks!

Try flashing SPDREM_U_01.6.7.2-180_SPU-19-TA-11.2_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot
with rsd lite.
Those failures are because of two things:
1. You are trying wrong sbf for another region
2 and/or you are trying to flash an older firmware.
Please note that now your only bet is to flash ICS firmware, and try various regions untill you find your right one.
Also if you manually flash use eprj-mfastboot , others fail to flash corectly.
Again for the power issue, when RSD throws an error , look at the phone, if it says "Low battery, cannot program" then the factory cable is bad, if not there is no power problem.
Don't worry your phone is not dead, you only need to find the correct sbf file, try more variants with rsd lite, it must work.

Mine had problems flashing correct sbf's, it was my system. Even with correct drivers and lastest RSD it would not work, nor with my other laptop, but working fine on my old xp install on a macbook. I could however install stuff individually using fastboot flash command. Sorry that I dont have a solution but I just wanted to let you know that sometimes it can be your computer/os install.

still trying
@Killer2k8: Thanks for the encouragement, I will try with the file you suggested with eprj-mfastboot.
As per power: I seem to have tried so many times that the battery is way deeply uncharged (I hope it isn't permanently damaged once I get the phone to charge at all again), so anyway, I crack'd'er open and tried powering directly at the battery contacts (battery disconnected, of course). As you would guess from what you wrote, that did not make any difference to my problems... But also, it proves my factory cable is good, as I can even flash the few files that work if no power is connected at the battery contacts, powering through the cable only. Some files will transfer correctly, and when it says "writing", the phone will just reboot, causing an error - that's why I thought of power issue, e.g. the actual flashing process requiring more power than just the transfer... Anyway, that issue did not go away even with direct power. - Will see what happens once I find the right files for me...
I'm good with flashing ICS, that's what I wanted to do in the first place. And thanks for the encouragement!
@drolgnir: Thanks, I had the same idea, as initially I had tried everything from Win7 running in VirtualBox (at first, I only found all the tools for Win, should've really researched better before starting this), I thought maybe it doesn't have the proper low-level access to the USB ports. Anyway, since trouble hit me, I tried also on three different Linux machines (2 different dirtros), and also again on the virtual Win, and on many, many different USB ports on these (just in case it was a USB power issue), all to no avail. I guess Killer2k8's suggestion sounds most promising at the moment... Cheers anyway.

no luck - situation deteriorating..?
Sorry for the many posts, I hope someone is still reading this...
So, I tried the file you suggested. I flashed manually, not RSD, with "fastboot" from eternity project, which is the Linux equivalent to "eprj-mfastboot.exe", as far as I can tell (download from the same post as the Win version).
I could flash cdt.bin, ebr, mbr. Note that these are all just 16kB.
When trying logo.bin, it sent it ok, but during 'writing logo.bin...', the phone just switched off. After restart, same again. Same also with boot_signed.
Since then, things got worse: whenever I try to switch on now, it flashes ~1/4 of the red "M" logo, then flashes the AP fastboot screen, and repeats that a few times before staying off (sometimes not, just switches off right away). I can still get into the Boot Mode Selection menu by holding all three buttons, but selecting AP fastboot there has the same effect. Starting with power&Vol- button shows the fastboot screen immediately, but again only for a flash...
The only thing that will stay on is the SBF Flash screen, but I don't know what to do with that..?
So, I still smell a power problem, but neither applying external power, nor using the factory cable alone made a difference. The cable is ok, I re-checked. The fact that the SBF Flash screen stays on suggests that it is not a stuck power button (someone had that problem, apparently), am I right?
So, any suggestions from here? Thanks..

Although this doesn't help, I have pretty much the exact same issue. However, I do know what/where my phone is from, it requires the central Europe update. But apart from that the issues are identical; it only boots into the flash failed fastboot menu, and any RSD attempts have failed at cdt.bin, while using the fastboot tool does not work either as I get preinfovalidation flash errors. The utilities don't work either.
Now, as you did, I also tried quite a few different versions of the firmware, and none of them worked. So what I was wondering is, is there a way for us to find out exactly what version the phone 'thinks' it is on, so we can find the same/a newer version of the firmware to update it to? Because I am quite certain I am using the files from the right region, so it must be the version that is too old.

update: still struggling, but giant leap further! Please read my tale...
...just in case anyone might find this useful, I'd like to give an update on my "patient":
I actually managed to flash ICS on there! Kind of.. What I did, was:
With the battery unplugged, I supplied external power to the phone, additional to the factory cable. The issue was that it would often flash small files, but for larger files would successfully "send" them, but in the "writing" phase the phone would just switch off. So, I supplied carefully monitored 3.7V to the contacts, which seemed to make a difference, but in the "writing" phase, Voltage dropped to below 3V where it would again switch off. Ok, you can charge a LiIon battery with max. 4.2V, and you should normally charge the battery before flashing, so I tried again while providing 4.2V. And - Success!! Voltage would drop to ~4V during "writing", but it stayed on, and allowed me to further test which Firmware the device would actually accept.
I do not believe that applying 5V from an USB cable directly to the (plugged-in) battery contacts, as mentioned in the forums somewhere, is very healthy for the battery. I reconnected the battery and tried charging it directly from the contacts, but I made sure the Voltage would always stay below 4.2V. Occasionally in my exploits, the charging circuitry would actually spring into action (confirmed by a drop and fluctuations in Voltage, and the faintest of noises from the phone itself), and I used that of course to squeeze some life back in, but most of the time it would not charge at all. I can not say what combination of flashing attempts, rebooting, un- and replugging the cable, switching and changing the charging current,... actually triggered the charging process occasionally, sorry. I could not reliably reproduce it.
In the process, I also tried the DroidRazrUtility 1.8, which interestingly flashed the AP fastboot to v 0A.74, but of course failed further on...
With the new AP fastboot, I thought maybe something more might now work, and at last I found it would now miraculously accept:
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot.xml and
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b_Service1FF_fastboot.xml
Fantastic!
First thing, before any actual booting, was to try if I could finally charge my battery again, and at last - yes!
At about 70%, I got adventurous, and unplugged the charger to put it in another power outlet. This made the phone actually boot up, but I thought that's not too bad now... But:
Now I have the following issue: After being freshly flashed (I tried several times now), it will charge as long as I don't actually switch it on, ONCE, but when it boots, after asking the setup questions and a little while on, it will switch off on its own, and then it's stuck in some variation of the bootloop (M dual core logo, pulsing M forever, OR rebooting ever and ever again at the pulsing M, OR just stuck at the M dual core). At least I now have a recovery menu. Erasing cache and data DON'T solve the issue (as proposed many times in the forums). I read a hint that it might be a kernel issue, or that it might be caused by a wrong radio.img (CDMA on a GSM phone). I checked and tested the latter by deactivating the radio in the extended settings, but it would still switch off after a short while (and it had defaulted to GSM, as it should).
So...am I stuck to wait for some new Firmware to come out, that might fix the issue? Or what should I try? Thanks in advance...

Resolved!
Long read, but I finally managed to do it. Basically, I am not 100% sure what happened, but I have a hunch:
After I thought I had solved the power issues by at least being able to charge the battery once after each re-flashing, I tried to fix the issue about the phone randomly switching off (and on - it wouldn't stay off!). I read that it might have to do with flashing failures (no error message??), or incorrect kernel or radio images...
Not long, and I ran into familiar problems again: It would flash the smaller files, but not system and cdrom; it would successfully "send" the files, but never stop "writing" them (I waited for somewhere between 10 min and an hour at each attempt), only way to stop the process was to switch off the phone, which certainly is not healthy during flashing...
...so battery started to go down again and I started to more and more clearly face a power issue again (I had disconnected the external power and didn't want to risk that McGyver approach again). As it happened, I also 'got some new USB 3.0 external hard drives at this time. I found that one would readily power up on all my USB ports, the other one could not get enough power even from some supposed 3.0 ports..
...which made me try flashing the very same firmware I was just trying (with the factory cable, of course), all the smaller files of which worked on the one computer but not the large ones (indicating I had the right firmware, at least):
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_ Service1FF_fastboot.xml
, on another computer, on the one USB 3.0 port that had proven to supply the most power - and taa-daa! It wrote it, very quickly, without complaining!
And it booted alright (after charging it first, just in case). And it stayed on (and off, when I eventually rebooted it). I am running that ever since, and it seems ok...
Originally, I had aimed for:
SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b _Service1FF_fastboot.xml
, but I think the differences are minimal and I don't want to risk anything going wrong again, right now.
In conclusion, to me the main issues were
- finding the right firmware, stupidly not having paid attention to the original version number, and
- all sorts of different power issues!
The factory cable did not solve all of my problems.
Recharging the battery (eventually) did not solve my problems.
ADDITIONALLY, it needs to be flashed from a USB port supplying sufficient power!
This might point into the direction drolgnir suggested, but for me, it was not an OS/driver problem, but definitely power (same, fresh install of Fedora Linux on the two machines that did, and didn't work, one of them alternatively running Win 8; the Linux Mint computer I also tried doesn't have USB 3.0, the USB 2.0 ports - including an externally powered USB hub - did not work). @drolgnir: maybe it was power for you too, but you didn't notice because it was a different OS too?
...I hope this overly detailed report might help someone else too...

Related

[Q] I need help with my fascinate

I have a fascinate and have successfully rooted it, flashed the cricket info (i got talk and text) and had 3g at one point. All of the sudden 3G went out. I put CYANOGEN on there, latest 7.1 i believe for the fascinate.
Upon trying to revert back to the original ROM so I can get in there with PST and CDMA WS, I encountered a very strange set of problems and now I am just stumped. I tried to ask a couple of other people and no one seems to know what is happening.
Here is what happens, I try to put the original ROM on there, by using ODIN and doing the atlasv2.2 pit file, and the original ROM, froyo, and the other one eclair i think.
When I use odin it gets to the system part, then right after it goes to the part that would take the longest, and I forgot what its called, dataFS? it has FS at the end, and then the phone (while odin is still going) will go to either a blue screen or a green screen with no words. If you look closely, it appears there is a clock at the top right just like if the phone was on.
I have not overclocked this device at all so thats one thing that can be ruled out.
I've tried odin using both battery in and battery out method as different guides have stated different things. When the battery is out, I get a blue screen. When its in, i get a green screen.
The screen appears right after the normal odin screen, with the status bar, but it will dissapear when it comes to the dataFS part (right after system) then it will take about 20 - 45 minutes and I will get an error screen on odin.
Funny thing is i've used odin and that method and it worked the last time. It works fine if I need to flash a clockwork recovery. However, upon booting into recovery, half the time I will get an error that has to do with BUILD.prop and SCH-I500. This is when I try to flash any rom except MIUI. For some reason, MIUI kicks this phone around and its the only rom that works. CM7 wont work, stock won't and every other rom wont.
So, to sum it up, my main problem is ODIN and its funky behavior, and not being able to go back to stock so I can see if my 3g settings are correct. If you have any information, even if its just something to help get my wheels turning, then please post it up, any and all help is greatly appreciated folks, thanks.
I dont know if this would work but if u think the problem is Odin then I would uninstall odin and reinstall the newest version available. Also, make sure the phone driver software get done the same.
Then after that I would try odin again. Phone off, battery out. Open odin. Plug in usb. Make sure phone set usb to debug. Hold vol down button. Odin should see your phone.
Im sure u know all the steps up to this point but try again.
Good luck
Or u can try running odin as Admin on the comp.
Also if the problem persits I saw a user had a similar problem and of turned out to be his usb cable so try a different one if you can't fix it.
Sent from my ADR6350 using Tapatalk
See, thats what I thought too, but I will give it a shot and see. I doubt its the drivers, odin or the program, file or anything else because it does work with clockwork, and i've downloaded it several thousand times, plus it works great when I do anything but flash the original rom, odin will go fine. Drivers seem fine, it communicates and all that perfectly so I also highly doubt that.
I will get another cable and just try it on a whole different PC to see what happens. I was really hoping someone had this happen and had a fix but I might have to do some heavy delving. THANKS GUYS! I will try this and report back.
It was the cables, used a brand new USB cable and it worked, strangest thing that a cable can work but not work and its just a bunch of wires, but almost all my audio cables have to be bent or else you will loose a channel. I guess its just poor quality materials. So thank you, it works now and it was just the USB cables.

[Q] Bricked??

Tried to unroot, now I have this. Been trying to flash through Odin (PDA md5 file only), gets to 'system', goes about 10 minutes then fails. Nothing on sd card. Im hoping I can save this. Any help would be greatly appreciated.
This is a retail Wifi.
I have the correct USB drivers and can see it in device manager but not in explorer. I do not have the correct ADB SDK, cant seem to find it.
Been reading several threads and watching vids on youtube, nothing seems to do the trick. Im stuck but hopefully not bumming.
This may or may not work for most but this worked heavily for my 2 units that had the same issue. One with a broken nvflash, the other that faced a bootloop and never booted up again. Took almost a week and I felt almost all hope was gone because the bloody service centre's refused to accept the unit's as they were not purchased from the region, rather online. Scumbag Samsung .
[!] This is usually a 90% fix for both broken nvflashes/deep sleep of death, considering you haven't drowned your Tab by now with no hope . I ask that you kindly attempt this once if you haven't before you QQ to the nearest Samsung center like I did.
- Drain your tablet
And by all mean's do so, The quickest way to get this done in less than 2 days or so (Depending on the battery percent charged) is to get a clear tape and tape around the power button pressed.
- Testing if you have drained it completely/Taped it right.
Connect the tablet via USB to your PC, make sure you have the NV Driver files [http://forum.xda-developers.com/show...php?t=1130574]
Just install the driver and proceed to the step where it asks about holding down the [Power button] +[ Volume+] and wait for the constant USB connect/disconnect sounds. It also helps to look at Device Manager to see if it still pops up.
When the battery is completely drained it will stop popping up in the device manager, and your ready to go.
MOST IMPORTANT STEP
You have only 1 and only 1 chance per drain to get this done right. Plug it into the socket charger and see if the charging icon should come up, after being fully drained you should see the charge icon should pop up [100% tested and works, this step is annoying but it's the tablet version of taking out the battery and popping it back in] and what ever you do, DON'T BOOT IT UP NORMALLY, instead press [Power Button] + [Volume -] keys and let go when you see the logo to get into fastboot mode.
Select the android buddy with the [Volume +] key and it will boot into Download Mode.
From here on out everything is easy sailing. Get the right firmware and Odin and flash the firmware you require. It doesn't matter what region you are from, the tablet is made to accept any regional firmware BUT the model number should be the same. Which mean's 7500 for 7500 ONLY.
Edit: Since you have only one chance per drain, I suggest you flash a stock firmware rather than flashing CWM to save it, Because CWM would only fix the recovery, It wouldn't fix the damaged bln. The fastest way to get a stock firmware is grabbing the stock firmware from the Overcome thread
Click to expand...
Click to collapse
Source:
http://forum.xda-developers.com/showthread.php?t=1478361
Ok, killed it that long....actually, just havent had time to get into this or deal with the frustration.
Anyway, it did what it was supposed to, meaning the battery icon came on. then I booted to download mode, plugged it in to the PC and it hooked up to Odin. It ported and I started to load the md5 file. I get stuck at the bootloader.bin. Been sitting there for 40 minutes. Has not failed yet. What now??
Never mind, I am an idiot who needs to read more. Please ignore me.
Sent from my GT-P7510 using XDA Premium HD app
Any and all help is appreciated, nobody is an idiot, except me for bricking this thing.
By the way, about 20 minutes after I posted the screenshot, it failed.

[Q] Weird charging problem

My friend is having some problems charging his Atrix. Basically, the phone will not charge or recognize a charger at all except for under certain circumstances.
Some background info: I helped him unlock his bootloader and install 4.5.91 way back when it came out. No problems there, it went well. All was fine until the 4.5.141 OTA update came around. He got the OTA notification and clicked update because he didn't know anything bad would happen. Luckily it didn't brick him like it did a lot of people, but he said it gave him an error message during the install and it would not boot after that, stuck at the Motorola dual core screen. I took a look at it and managed to get into recovery and flash back to 4.5.91. All was fine until it was time to charge the phone. It wouldn't recognize any charger. I tried flashing to tons of different roms, wiping everything, even restored a full nandroid recovery from my working Atrix on it. His phone will charge and will be recognized by a computer immediately after we flash a new rom, and will continue to charge for as long as we leave it plugged in, but if we unplug it then after a short time (like under 30 mins) it will not recognize a charger if we plug it in again. Wiping data alone will not make it start charging again, only actually installing a new rom will. Deleting battery stats does nothing. The closest we have gotten to fixing it was when I made a nandroid on my Atrix and then restored it on his (my backup was from Joker's CM9); after the restore, it would charge for a while, and we unplugged it and waited to see if it would do the same thing as it always did and stop recognizing a charger after a few minutes. About 30 minutes later it stopped recognizing the charger as usual. We played with the USB debugging setting (enable, plug in, see if it recognized the charger, disable, plug in, see if it recognized it, etc) and after messing with that setting a lot it recognized the charger once, but then when we unplugged it the phone wouldn't recognize the charger again. We could not reproduce this again.
To summarize what we have tried and found to work:
-flashing a rom will let the phone charge/let a computer recognize it for as long as we leave it plugged in after the first boot (we have tried every rom under the sun, they all do the same thing)
-restoring from a nandroid backup will have the same effect as flashing a rom
What we have tried that didn't work:
-different cords; have tried them all, both OEM cord and third party, this is not the problem
-wiping all data/factory reset doesn't do anything
-cache wipe doesn't do anything
-wiping battery stats doesn't do anything
I have also tried fastboot flashing back to 4.5.91, CWMing back to 4.5.91, using the unbrick scripts and stock restore scripts people have made, nothing will fix it.
If anyone has any suggestions or can refer me to anywhere with more info on this I would appreciate it, I have searched high and low and can't find anyone with a problem quite like this one. I don't even know if it's a hardware or software problem, if you guys know a way to determine this it would be helpful.
Have you tried a wall charger?
Yeah, both the stock one and a different one I have, neither work.
No one has any advice or ideas on this? Does anyone know if Moto does repairs in this type of situation with a voided warranty because of an unlocked bootloader, or does anyone know who may be able to fix this if I can't get any help from the forums or figure it out on my own?

Unbricking the P9000

Even though I (and other members) already posted about the issue, I figured I make another post for everyone to see.
Hopefully this will help you to unbrick your phone, without taking it apart to disconnect the battery.
First of all: what are the symptoms?
In my case I flashed the phone according to the guides found in this forum. Everything worked pretty well until I wanted to revert from CM13 to stock.
I followed the procedures, but after doing so the phone would not turn on. It would not show that a charger is connected, and, of course it would not boot into recovery.
What happened?
While flashing the phone with the official stock ROM ([ROM] Stock ROM Elephone P9000_Android_6.0_20160419) I also flashed the preloader (as it is not explicitly stated to not do so).
That was the cause of my problems. Without the correct preloader, the phone will not work anymore (except for a fallback method to correct that mistake).
Trying to flash it again resulted in the error message "BROM ERROR - STATUS_EXT_RAM_EXCEPTION (-1073414139)".
What to do?
First, connect your phone to your Computer. Open the Windows Device Manager and leave it open. Press VOL+ on your Phone, and you should see a new device popping up (can't remember the name, sorry), and disappear a few seconds later. That device is the fallback for flashing the phone even in a softbricked state. Make sure the driver for that device is installed properly (as long as there is no exclamation mark you should be fine, but this is a possible problem source).
After ensuring that functionality, it is time to find a preloader which will work. You can try the different stock ROMs found on the official elephone forums (in my case Elephone P9000_Android 6.0_20160304 as well as Elephone P9000_Android 6.0_20160608 worked - ymmv).
Disconnect your phone and start sp_flashtool and load the scatter file associated with the firmware. Select only the preloader, leave it on "Download only", click on "Download", connect the phone to your computer and press VOL+.
The download should start and hopefully complete without problems. After the successful flash, Windows should immediately (maybe after reconnection, not sure) recognize your phone as a Mediatek preloader device, the screen should turn on and show the image for being charged, and also the notification LED.
When successful, you should flash the rest of the ROM to the phone, with the exception of the preloader.
If your phone won't turn on after flashing, leave it to charge for a couple of minutes.
That's what helped me. If you do not succeed right away keep trying.
Good luck.
You´re my man!!!
after more than 10 tutorials to unbrick the phone this way was nearly the perfect one.
i totally agree with your steps, but nothing happened in the SP FlashTool after "DA Download" appeared
To continue with the Download i had to "play" with the Powerbutton too, after 2-3sec of pressing, i heard the device is plugged in sound, then it ran through the steps. phone works as smooth as before i deleted the preloader.
After 6hours of trying, testing, mental breakdowns and thinking i have to buy a new one...
maybe someone else will be happy with this additional hint

Modem did not power up (3)

Hi guys, I'm new to the forums. Didn't need to use it befor so here's my first post:
Some months ago I dropped a box over the phone, the surface of the screen got a little broken but it still works anyway. Thing is that after I let the phone discharge completely and tried to power on again a message appeared, not allowing the phone get past that:
Unlocked
Modem did not power up (3)
Starting RSD protocol support
Battery is too low to flash
Click to expand...
Click to collapse
From that, I can infer that there is some problem that can be fixed flashing the firmware again through RSD or fastboot (I'm not sure), but for some reason, the battery remains "too low" even after leaving it plugged for hours in that screen.
BTW, the bootloader is unlocked and, the phone rooted and CWM Recovery installed. Also, I think installing a ROM through Recovery doesn't work. Any help? I saw a post about some similar error "Modem did not power up (0)" stating that modem chip is disconnected for some some reason. It could explain how my error was triggered (dropped a weight over the phone). However I don't want to mess opening the phone as long as I'm not sure of anything.

Categories

Resources