Hi,
I had a problem with the micro-usb port/charger in my galaxy s2. It was what others have already described (constantly charging/not charging, voltage too high messages, etc). So I decided to buy a spare part for the charger, and replace it .
The first time I turned it on, The charger problem was completely solved, but I noticed the signal was gone. I realized I forgot to connect the antenna. So I opened it again and connected it. The antenna is a HF cable which connects to one end to the main board, and to the other end to the spare part I bought.
After reconnecting the cable I saw an improvement, but the signal is still much worse that before replacing it for the first time.
I bought the part here (German language):
[] IShallNotPostLinksAsANewUset []
Could it be this replacement part?? Might be a capacity adjustment problem? I don't know how are usuallry phone antennas designed. I don't know either if this part plays an important role for the antenna (it is anyway connected to the cable).
What can it be? What would you do to recover antenna sensitivity? (I do not have the broken part, it is already gone )
Best regards
duguet said:
Hi,
I had a problem with the micro-usb port/charger in my galaxy s2. It was what others have already described (constantly charging/not charging, voltage too high messages, etc). So I decided to buy a spare part for the charger, and replace it .
The first time I turned it on, The charger problem was completely solved, but I noticed the signal was gone. I realized I forgot to connect the antenna. So I opened it again and connected it. The antenna is a HF cable which connects to one end to the main board, and to the other end to the spare part I bought.
After reconnecting the cable I saw an improvement, but the signal is still much worse that before replacing it for the first time.
I bought the part here (German language):
[] IShallNotPostLinksAsANewUset []
Could it be this replacement part?? Might be a capacity adjustment problem? I don't know how are usuallry phone antennas designed. I don't know either if this part plays an important role for the antenna (it is anyway connected to the cable).
What can it be? What would you do to recover antenna sensitivity? (I do not have the broken part, it is already gone )
Best regards
Click to expand...
Click to collapse
Hi, after having had the same problems with charging, I also changed the micro-USB flex circuit/cable. I bought it in the UK from e-cell (on ebay) ... and same as you, I am not able to get 3G anymore, only G! Charging is solved, 3G is gone!
I do have the old part still ... will put it back on and see what happens.
UPDATE:
OK, I put the original part back in ... and 3G/H was immediately back. I can also see that the network strength is the same as with the replacement part (so it doesn't seem to be a defective antenna cable or so), but now it picks up UMTS and HSPA+, while the replacement part only caught GPRS. So what this means is that the replacement part is not the same as the original ... probably the same problem you have.
At the same time there was no miracle and the original part is still no charging unfortunately ...
I had ordered 2 other replacement parts in HongKong which should arrive in a couple of weeks ... will try those when they arrive, and hopefully at least one of them will solve the charging AND the 3G issue!
UPDATE 2:
While driving around with the phone with the replacement part, sometimes I do get E/3G/H+ signals, so it appears that the part is able to handle these ... but maybe only when the signal is very strong? Or maybe there are different types of E/3G/H+ signals?
Hi,
Experiencing the exact same behaviour, the signal is really bad (never above 3 bars). I'm going to open the phone tomorrow to make sure I left the antenna cable properly connected, but judging from what I'm seeing here, I believe the issue is with the small circuit with the USB port. I bought my part from e-cell as well....
Thank you very much for your answers guys. Now I know that my problem is not unusual. however in my case the 2g signal receptiony is also to degradated. Please keep us posted when you get the spare parts from Hong Kong. If they work I will also order 1 myself.
Sent from my GT-I9100 using Tapatalk 2
duguet said:
Thank you very much for your answers guys. Now I know that my problem is not unusual. however in my case the 2g signal receptiony is also to degradated. Please keep us posted when you get the spare parts from Hong Kong. If they work I will also order 1 myself.
Sent from my GT-I9100 using Tapatalk 2
Click to expand...
Click to collapse
OK, good news ... today I got my second part, and this one seems to work just fine! 3G and H+ are back! And of course it charges.
As I ordered 2 different parts at the same time from HongKong, I am not 100% sure which one I got, but I am quite confident it is the one from mingxing200808. The item I bought is sold out now, but he relisted it (at higher price: 6.90 USD vs 3.90 USD that I paid, still worth it though). Note that the picture posted is not the same as the part shipped (which was newer, at least in my case). Also note that you need to reuse the rubber cover of the microphone (e-cell included that rubber piece). There is also no adhesive on the mingxing part, but as far as I can see you don't need that either.
Good luck!
Geronymous said:
OK, good news ... today I got my second part, and this one seems to work just fine! 3G and H+ are back! And of course it charges.
As I ordered 2 different parts at the same time from HongKong, I am not 100% sure which one I got, but I am quite confident it is the one from mingxing200808. The item I bought is sold out now, but he relisted it (at higher price: 6.90 USD vs 3.90 USD that I paid, still worth it though). Note that the picture posted is not the same as the part shipped (which was newer, at least in my case). Also note that you need to reuse the rubber cover of the microphone (e-cell included that rubber piece). There is also no adhesive on the mingxing part, but as far as I can see you don't need that either.
Good luck!
Click to expand...
Click to collapse
Hi Guys, I have had this problem also after replacing the usb board, it has been a nightmare thinking that other parts may have been water damaged I replaced the loudspeaker and inner chassis which both have antenna components. After reading your post I ordered a used part from gaproducts on ebay at £3.85 and my phone is now perfect. By the way the defective one was from china via ebay and supposed to be genuine. Wish I had seen this post a month ago it would have saved me so much hassle, but hopefully will help others.
This is strange, i have the same problem after changing the Flex Cable + Charging port. I bought it from ebay (user name yake-gandi3388) so be careful. I requested a refund or replacement but not sure what the answer will be. The phone never connects now to HSDPA (H), it always stays on EDGE (E). On top of that the signal is somehow weaker than before, not significantly, but I can notice it
I thought that the Flex Cable+Charging Port are not linked to Antenna performance in any way Can someone more experienced explain a bit?
Also, anyone tested an aftermarket flex cable+charging port that is working ok, including the antenna performance and full 3G connection?
Thanks!!!
Ive followed about 10 threads about changing usb boards.About 1 person was happy,and the other 9 got other problems.
When they put their "faulty" one back in,the "new" problems vanished.
Most were replacing the board because of usb problem.
I thought they were buying faulty replacements.For all I know someone at Samsung could be "recycling" faulty parts..
Sent from my GT-I9100 using xda premium
I'm experiencing the exact same problems!! What's weird is that with other carriers (that work in different frequencies) my phone works just fine... I'll try buying another flex cable and will tell you the results.
da_17 said:
I'm experiencing the exact same problems!! What's weird is that with other carriers (that work in different frequencies) my phone works just fine... I'll try buying another flex cable and will tell you the results.
Click to expand...
Click to collapse
Strange... I will try to check with other providers as well. On my side, I have re-contacted the Ebay member and he offered me an additional Flex Cable with no extra charge. Nice commercial initiative, however I am afraid that the next one will have the same issues Will keep you updated once it arrives.
Got this as well. I changed my USB board after it developed charging problems. The first one gave me a flashing battery icon & one of the screw holes didn't line up also. The next one fitted fine but I'm sure my signal is weaker. Compared to my friends S1 on the same network. He gets a stronger signal than me, stood in the same place. Replaced my loud speaker/antenna as I've also replaced the back chassis and think prising the speaker out might of damaged it. Think I'll try another USB board to see if it improves :S the 2nd board had the same Rev. number on it but looked slightly different to the original. (Sadly dont have the original to put back in to test)
Sent from my GT-I9100
I am signed up for a solution to this problem.
I had charging issues with the old port and replaced the board. The new board only allowed for an intermittent 1 signal bar. I put the original faulty board back in and had full signal immediately.
I ordered a second board and have the same issue. No/1 signal bar. Cannot make calls, it tells me "mobile network not available." I can connect to wi-fi with no issues though.
Unless a fix is found I am considering taking one of the new boards and my old board into a service shop and having the usb ports swapped.
Galaxy S2 SGH-i777 (AT&T)
I received a 3rd charging port board today, this one works some, but not as good as original. I'll post the number's printed on the board with there results in the phone.
Original Board: GT-i9100 REV2.2
R.B83 35
Original board worked great until it started having issues with charging/high voltage.
Replacement Board 1: GT-i9100 REV2.3
R.C42 10
This board would charge the phone and connect it to the computer, but would not connect to a network and would give no signal or a temporary 1 bar signal.
Replacement Board 2: R.B54
GT-i9100 REV2.2
This board would charge the phone and connect it to the computer, but would not connect to a network and would give no signal or a temporary 1 bar signal.
Replacement Board 3: GT-i9100 REV2.2
R.B83 36
This board both charges and connects the phone to the computer and it allows for a network signal. The network signal is not quite as good as my stock, but I think it will do.
I do not know what the board numbers mean, but I would guess the REV2.3 is an updated version of the REV 2.2. I think the compatability issue may come in the R._ numbers as Replacement Board 3 is the only one that works and is the closest R._ match. Maybe someone with far more expertise can shed some light on it, but this is my experience.
Geronymous said:
OK, good news ... today I got my second part, and this one seems to work just fine! 3G and H+ are back! And of course it charges.
As I ordered 2 different parts at the same time from HongKong, I am not 100% sure which one I got, but I am quite confident it is the one from mingxing200808. The item I bought is sold out now, but he relisted it (at higher price: 6.90 USD vs 3.90 USD that I paid, still worth it though). Note that the picture posted is not the same as the part shipped (which was newer, at least in my case). Also note that you need to reuse the rubber cover of the microphone (e-cell included that rubber piece). There is also no adhesive on the mingxing part, but as far as I can see you don't need that either.
Good luck!
Click to expand...
Click to collapse
viva! the party from Hong Kong worked for me. For everyone which needs this part search for
the vendor on google. I am using my phone for the 2100Mhz 3 g band.
Cheers!
Sent from my GT-I9100 using Tapatalk 2
Good.
So whats the vendors name....or is it classified.
Sent from my GT-N7000 using xda premium
I changed my usb port as well due to not charging/over voltage, ordered it from hongkong via ebay.
Been using the new one for over 6 months now and i would be lying if i said i had any 3G problems. And someone already asked this in this thread but no one has answered it. How are usb charging port and 3G signal linked??
Sent from my CyanogenMod 10 powered GT-I9100 using xda premium
krayndr said:
I changed my usb port as well due to not charging/over voltage, ordered it from hongkong via ebay.
Been using the new one for over 6 months now and i would be lying if i said i had any 3G problems. And someone already asked this in this thread but no one has answered it. How are usb charging port and 3G signal linked??
Sent from my CyanogenMod 10 powered GT-I9100 using xda premium
Click to expand...
Click to collapse
The USB board has the contacts to connect to the antenna in the back of the chassis. So replacing it with a sub standard part is affecting signals
Sent from my GT-I9100
duguet said:
viva! the party from Hong Kong worked for me. For everyone which needs this part search for
the vendor on google. I am using my phone for the 2100Mhz 3 g band.
Cheers!
Sent from my GT-I9100 using Tapatalk 2
Click to expand...
Click to collapse
Please let us know the vendor name on Ebay. As mentioned in my previous post, the vendor (user name yake-gandi3388) agreed to change my replacement with no extra charges. I installed the new piece...the signal is a bit better than previous one...but still lower than the original.
Can anyone advise a vendor that sells replacement part Flex Cable with a strong signal?
Blue Angel o.O said:
Please let us know the vendor name on Ebay. As mentioned in my previous post, the vendor (user name yake-gandi3388) agreed to change my replacement with no extra charges. I installed the new piece...the signal is a bit better than previous one...but still lower than the original.
Can anyone advise a vendor that sells replacement part Flex Cable with a strong signal?
Click to expand...
Click to collapse
I an sorry for for the delay. I live in Germany and I use O2 ( umts frequency in the 2100 Mhz band) . I ordered the part from Hong Kong which Geronymous cited, didn't want to make specific advertising. The user is mingxing200808.
Regarding the question why does this affect the antenna, it is because antennas need to have a certain capacitive load in order to be adjusted and to transmit in a certain frequency range. If the antenna is not adjusted the signal will be reflected back . This capacitance is defined by the geometry of the antenna and might be changed/adjusted by elements connected to the end of the antenna. So the flex part acts as an adjusted capacity load for the antenna.
This is a very rough description, but I hopeit helps.
Greetings,
Sent from my GT-I9100 using Tapatalk 2
Finally got my 3rd USB board and my signal has improved a lot! Hurrah! Got from tjuk1980 on eBay. This board is a darker blue, looks a lot better than my second board which was a lighter greener colour, the logo and writing didn't seem as clear as it does on the new one. Getting 3 of 4 bars on H+ at home where as before it would stay on G and if it did pick up 3G/H by chance it wouldn't show any bars.
Sent from my GT-I9100
Edit: picture of the dodgy board - this gave me crap service so avoid that one!
Related
ok i may have this completely wrong as i have not tested it yet but i noticed on the back of my tg01 i had 2 round black stickers, one top left, one middle left.
After peeling this stickers off i have 2 little ports which look remarkably like the ports used on internal wifi chips (laptops, nintendo ds) which the areial plugs into for the wifi signal
We can now enhance the tg01's wifi reception with a little careful wire placement
i hope his helps someone with the wifi reception & maybe better battery life as its not having to try so hard for a signal
comments?
Are you sure one of those are not for a external GSM antenna? Like for using in a car
no, i did think this but they are to small. only 2-3mm across. i know what im talking about when it comes to hardware, they are definitely wifi ant. ports.
http://images.google.co.uk/imgres?i...internal+wifi+connector&um=1&hl=en&tbs=isch:1
this site has loads of pics and prices for the relevant hardware
its called an ipx connector, the pigtails they sell can be used to act as the antennae.
i think this could be a good thing
that connector u linked in is a standard connector used with laptop wifi card , they have a little pin in the middle , the connector on the tg01 has no pin in the middle , the ring around it is the shading
kk here is what i know so far.....
most (if not all) builtin wifi chips have an antenae port out, i know this through research with the nintendo ds, and internal laptop chip on various laptops ranging from toshiba to sony.
they commonly have two of the ipx ports for the loop with the wifi flylead.
it may be possible qualcomm have used a proprietary ipx adapter for extra sales through the hardware of there chipset or toshiba have gotten the grubby little hands on it and done it that way
we need people who want to run an experiment on this and find out if they are what i think they are or if im completely wrong
volunteers????
i happen to have a connector ur looking for , but , it doesnt have a pin in the middle and its 90' angled so it wont fit unless i get the back cover off ... with that said , i dont have a 3angled srewdriver thats needed
... ill make some pics later
could it be possible the snapdragon chipset has done away with the pin for a design point? they may be purely there as a dud bit of hardware as qualcomm have directly etched the wifi ant onto pcb and not allowing the flylead?
or...
they may be semi usable with the core (the bit with the pin) etched onto the pcb and the earth allowed to be enhanced by just using the outer rim of these ipx ports?
or...
im totally wrong and as well as the usb host function you could attach a couple of jump leads to the beast via these ports and jump start that big ol v8 what keeps stalling?
Perhaps they could be test points, do you think you can show us a photograph?
i will upload pics tomorrow, they wont be great quality as i have to use my wifes blackberry for em and it dont take great up close pics.
test points are a possibility, tbh it did cross my mind but usually there just dotson the pcb, not ports, but it is a more advanced piece of hardware.
just out of interest but if you were to hook it up with the ports via usb, there would be a chance you could damage it because of the power usb ports output. if it turns out to be wifi then your gonna blow the chip or worse.
but if you want to try it then by all means psot results
hope this help
http://img688.imageshack.us/img688/5106/p1210021g.jpg
nice one!
looks like it connects two aerials for better wifi/radio
compare the connector with this
i558.photobucket.com/albums/ss28/linyedongwyl/Intel-5300-half.jpg
thats the connector for the ipx that has been linked earlier , this is a little different , it would be nice to see what the connectors look like on the tg's wires?
alrite , lets compare this baby to the xperia x1
www.phonewreck.com/wiki/images/b/b2/Xperia_x1_pcb_1.jpg
u can clearly see it also has two unused connectors of the same kind wich appear to be unused /but on tg the two upper ones were connected on the pcb!!!/
as for the interconnection of unknown function on the backplate they used the battery cover to pass it thru(the cover's back is unpainted on thoose specific points to give conduction) if it were to just hold the cover in place the would of left the paint on
see the four pins on the phone around the battery
www.ubergizmo.com/photos/2009/3/xperia-x1-battery.jpg
so i was right, we can get better wifi signal with these ports.
and then
better signal + less energy needed = better battery life
and the SE using the conductor pins for the back cover they have used that on the old w series of phones to. no real idea of what it does though
thanks to those who uploaded pics, helped out a lot with explaining what they are and the circuit detail.
so who' gonna be the first to install this on there phone and so testing for battery life and signal improvement?
Did you get anywhere with this? Very interested!
This sort of thing would surely work:
http://www.ebay.co.uk/itm/800-900-1...099221?pt=PDA_Accessories&hash=item4ced70add5
IPX antenna.
Alternatively.. what would almost 100% work is a replacement antenna cable for the tg01
Although I could be wrong... if you look at this review of the LG P990 (Optimus 2X) you will notice the two different types of connector: http://www.anandtech.com/show/4144/...gra-2-review-the-first-dual-core-smartphone/9
External aerial points for testing the phones at the factory? Can they be used/abused to get an external or bigger aerial setup? What connector is that without the pin????????
Update.. is it an MMCX connector ? (or even MMCX-KC). I am tempted to buy one from ebay (although my TG01 is bricked LMAO, at least I'd know if it fit!) Pretty certain now it's an MMCX connector. Now trouble is... you can get that connector for GSM and GPS... so what are the connectors for I wonder.
For example.. I have terrible reception in the office so having a bigger external aerial on the phone may help, but I'd be interested in a better GPS cable as well Let's have some fun!
EDIT: OR.. I just had a look at my Moto V3i external connection and that is almost identical to the connectors on the TG01.. and it looks like you can get an aerial/antenna kit for the v3/v3i Might give it ago but it's pricey at about £20 :-(
LMAO @ this link: http://www.ehow.com/how_7580234_increase-reception-v3i.html Fancy testing a paperclip guys?
Well... I just ordered a 3G/UMTS antenna from china (so will be a while) with a MMCX connector. I will let you guys know if it fits AND works
Another edit LOL: I also just ordered another external antenna. This time for the V3i RAZR, as it looks like it has the same connector type as the TG01, so will give that a go. Only cost £8.05 for the adaptor and the antenna, so not 'too' bad for something that should fit.
Thread for hardware mods
POSTING INTERNAL tf101 pictures
like 3g dongle ? internal sd cards? ssd?
removing the battery for 2 HDD 500go?
finding sd cards hubs? usb to sata cables?
? there is a place in the tablet for a 3g dongle?
there are 2 screws under the upper rubbers and the dock open easy
there is a lot of spaces avaible
My MIFI might actually fit in there, all I would need to do is supply it power somehow.
I'm no hardware engineer though, but if thats possible it would save you from the driver issues with a 3g dongle.
I wonder if it would be possible to check which pins from the adapter connect to USB - so we can make DIY USB adapter for those without a dock.
hmm adding an hdd would be very interesting, sata won't be very hard, powersupply will be.
Sent from my O2x with CM7
This is what I was looking for, looking to do some mods to the dock.
Thanks Markolino72.
Internally mount and wire a 32gb memory stick to the USB port so you get a 32gb hard drive added whenever you dock It might even have enough room for a portable USB hub so you don't lose use of the external usb port?
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
ydnality said:
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
Click to expand...
Click to collapse
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Regards.
In regards to the hardware mods, that really looks amazing. Would love to put in my mifi there as well, attach it via USB to charge = your own 3g model Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well. Only a few thoughts.
Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well.
Click to expand...
Click to collapse
it's a good thought but the mifi I have (novatel 2200) wont work without the battery, for some reason if the battery is bad or removed you cannot run usb, it must be the way they have the power run through the battery or charging. Not sure if all are like this or not.
andrewklau said:
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Click to expand...
Click to collapse
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Surprising how much wasted space there seems to be in the dock -- it's nowhere near as tightly packaged as the tablet itself. Looks like Asus can optimize the size or fit some more features in future versions, if they want...
Let me see if I am thinking correctly...Your saying using something like mifi installed via USB wires (will it be always on?) then connect via WiFi on your transformer? So basically your putting the mifi in a case that can never be opened without a screwdriver? I guess one would always have access for your other devices as well as long as the TF is in the vicinity.
P.S. I think I think this is a good idea, not decided though. I like to think of it in a real world application.
there is another post with a guy putting in an SSD, but it bulges at the keyboard. A 32g SD card would be nice.
Sent from my Transformer TF101 using XDA Premium App
typci said:
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Click to expand...
Click to collapse
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
tanguita said:
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
Click to expand...
Click to collapse
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
knoxploration said:
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
Click to expand...
Click to collapse
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
tanguita said:
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
Click to expand...
Click to collapse
Yeah, actually, I hadn't realized that but it does say it clearly on the product warranty page:
"Brazil and South American countries don’t support global service"
http://support.asus.com/warranty.aspx?SLanguage=en&p=20&s=16&m=Eee Pad Transformer TF101
took mine apart also and there is quite a bit of room.
i plan on putting a 128gb usb flash drive inside the dock and soldering onto the usb connections once i get all the bits in.
Any bigger pictures? Are the screws under the rubber feet?
just two screws under the rubber feet near the hinge then it just pulls apart from the top
had to take mine apart as the spring/clip mechanism for the sd card wouldnt lock the card in.
now the card is stuck in with no nails haha a simple fix.
This is good news. I hacked a Crystal HD decoder card (pcie), USB wifi dongle, a logitech nano receiver, and a 4 port micro usb hub (from a touch screen setup) into a Dell mini 9 and there was absolutely no room compared to this.
They even have covers for the USB ports, so if you remove a header and solder wires up you just have to hot glue / epoxy that cover from the back and you are money. Looks clean and stock.
I have an old 64 GB thumbdrive that might find a new home. Maybe a 1.8" usb HDD would fit in there with the battery, without the battery who knows.
Hi,
I recently replaced my usb flex cable, and my signal has been very weak ever since. I have tried loosening the screws and removing the small wire (aerial) and putting it back on, but my signal is still very very poor. Has anyone else had this problem after disassembly?
It may not be relevant but i'll mention it anyway. The screwdriver I used had a slight magnetic charge, just enough to pick up the screws. Could this have damaged something?
I'm on O2 UK and have tried other O2 aims, but to no avail. I have also tried my sim in other phones and signal improves greatly. I noticed it instantly after reassembling the phone so whatever has changed, happened during the course of replacing the usb flex cable.
Any help would be greatly appreciated, thanks
Does anyone have any ideas on what could be causing the signal to be so consistently weak? Would it be worth replacing the wire antenna?
I have taken this apart and put it back together countless times, trying to see if there was a loose connection etc, but have had no luck so far. I even put a bit of folded tinfoil between the usb flex cable and the contact under the battery to try and help the connection. I've completely run out of ideas.
Rotoq said:
Does anyone have any ideas on what could be causing the signal to be so consistently weak? Would it be worth replacing the wire antenna?
Click to expand...
Click to collapse
I think you just disrupt the antenna. Sending it to a customer service repairs should be a good choice
Sent from my LT18i using xda premium
As I bought it from Ebay IE, I have no warranty, so will have to pay to have it repaired. i was hoping to have a go myself, however there doesn't seem to be an awful lot of information out there regarding this problem. I have found a replacement antenna for £3 so I might try that, however I'm not sure that is the problem as the antenna looks in good condition and was only disconnected briefly.
Edit: Oh and thanks for the reply
send it to service center...
rocky23 said:
send it to service center...
Click to expand...
Click to collapse
I'll probably have to take it to my local electronic repair shop as it is not under warranty. i was really hoping to avoid this as I'm not sure what they will charge :-/
Rotoq said:
I'll probably have to take it to my local electronic repair shop as it is not under warranty. i was really hoping to avoid this as I'm not sure what they will charge :-/
Click to expand...
Click to collapse
well thts ok too jus watch out as wat hes doing?good luck m8 an do pm or post as how ur phone bhaves an costed?for repair
I'm hopefully going to leave it to be repaired this weekend but if anyone has any ideas please feel free to post them here.
well there are apps jus c in market"signal boost"u get a whole lot of apps jus giv it a try....
rocky23 said:
well there are apps jus c in market"signal boost"u get a whole lot of apps jus giv it a try....
Click to expand...
Click to collapse
Thanks, but it wasn't an app that caused the change, so I am reluctant to use an app to try and work around a proper fix.
Having read awful reviews for my local repair shop, I have just purchased a replacement antenna to try and repair it myself. It cost £3.00 so I'll fit it as soon as it arrives. If that doesn't work I will HAVE to take it to be repaired :-(
Rotoq said:
Thanks, but it wasn't an app that caused the change, so I am reluctant to use an app to try and work around a proper fix.
Having read awful reviews for my local repair shop, I have just purchased a replacement antenna to try and repair it myself. It cost £3.00 so I'll fit it as soon as it arrives. If that doesn't work I will HAVE to take it to be repaired :-(
Click to expand...
Click to collapse
Same problem here... I've just replaced my usb flex and after that i wasn't able to connect to my provider h3g 3 ita in wcdma mode...but just have roaming with other gsm provider...
I've also a sound problem from loudspeaker otr better i don'have anymore sound from my s2.
I'm reading that antenna is in the same part of luodspeaker so i hope to have break my anttenna part...
I've just oredered a new loudspeaker part and mybe i've to ordere also wire antenna...
After that i really don't know what can i think.....
Regards
cescof said:
Same problem here... I've just replaced my usb flex and after that i wasn't able to connect to my provider h3g 3 ita in wcdma mode...but just have roaming with other gsm provider...
I've also a sound problem from loudspeaker otr better i don'have anymore sound from my s2.
I'm reading that antenna is in the same part of luodspeaker so i hope to have break my anttenna part...
I've just oredered a new loudspeaker part and mybe i've to ordere also wire antenna...
After that i really don't know what can i think.....
Regards
Click to expand...
Click to collapse
I had same problem as you.
After changing USB flex PCB my network signal just vanished.
Fortunately I found solution for my problem.
Problem was in slightly different PCBs and after unsoldering one SMD element my phone is back with strong signal.
Anyway here are the pictures:
imageshack.us/photo/my-images/33/pcbn.jpg
Original PCB is upper one
imageshack.us/photo/my-images/204/pcb2m.jpg
There is difference
imageshack.us/photo/my-images/831/pcb3h.jpg
Thank you!
This worked like a charm!!! Thank you so much for your post! Save me so much money.....
LittleCannon said:
I had same problem as you.
After changing USB flex PCB my network signal just vanished.
Fortunately I found solution for my problem.
Problem was in slightly different PCBs and after unsoldering one SMD element my phone is back with strong signal.
Anyway here are the pictures:
imageshack.us/photo/my-images/33/pcbn.jpg
Original PCB is upper one
imageshack.us/photo/my-images/204/pcb2m.jpg
There is difference
imageshack.us/photo/my-images/831/pcb3h.jpg
Click to expand...
Click to collapse
I have the same problem...
How did you remove the SMD?
Magnetic screwdriver
Just FYI, magnetic screwdrivers do not cause any damage to electronic circuits and are generally safe to use.
tixxix said:
I have the same problem...
How did you remove the SMD?
Click to expand...
Click to collapse
Soldering iron with really pointy tip
Top man.......
Usb port broke so replaced it and had a very weak signal. after hours of checking everything, flashing roms, taking phone apart, 3 different usb boards and a massive headache. I followed your guide and now have strong signal again. Was nearlly at a point where phone was going to be scrapped. Thankyou
LittleCannon said:
I had same problem as you.
After changing USB flex PCB my network signal just vanished.
Fortunately I found solution for my problem.
Problem was in slightly different PCBs and after unsoldering one SMD element my phone is back with strong signal.
Anyway here are the pictures:
imageshack.us/photo/my-images/33/pcbn.jpg
Original PCB is upper one
imageshack.us/photo/my-images/204/pcb2m.jpg
There is difference
imageshack.us/photo/my-images/831/pcb3h.jpg
Click to expand...
Click to collapse
LittleCannon said:
I had same problem as you.
After changing USB flex PCB my network signal just vanished.
Fortunately I found solution for my problem.
Problem was in slightly different PCBs and after unsoldering one SMD element my phone is back with strong signal.
Anyway here are the pictures:
imageshack.us/photo/my-images/33/pcbn.jpg
Original PCB is upper one
imageshack.us/photo/my-images/204/pcb2m.jpg
There is difference
imageshack.us/photo/my-images/831/pcb3h.jpg
Click to expand...
Click to collapse
You are a life saver! I was about to trash my S2. I got it used with usb and sound problems for about 130 euro. Swapped parts but had crappy signal. The signal was bad before to which I also bought new antenna. Network signal never worked properly since acquiring the phone 2 weeks ago. Swapping modems never helped.
I still have the old USB board and it looks like exactly like the one I replaced. Thinking of the same thing you just did. Now my question to you, why didn't you remove the other SMD to make the boards match? I might try removing both on the old to compare signal levels.
Your info should be stickied!
Thanks again!
Tried that Trick but now I dont have any more signal at all...nowhere!
I have a second hand Galaxy S2 which was unlocked to all networks and randomly the phone would connect to driving mode. I used GoLauncher EX to delete Voice control but then it started showing that it was charging constantly. After a lot of research I found the problem was in the charging port.
I ordered a new charging port online and I've put it in instead of the old one and now the charging problem is gone, but now my phone gets no service on a Three UK sim, I'm quite sure it wasn't on Three UK to begin with.
Is it possible that changing the charging port might have locked the phone to the original carrier again?
and is there anyway to unlock it(without root) or get it working again a different way?
(This is my first post. Forgive me if I've made any mistakes. )
Got quite a few views. Does this mean no one has any idea on what it could be?
Take a look at the antenna wire sometime you touched it and it's not connected properly
Yeah I have seen a lot of people lose signal who replace that port. I'm pretty sure it has something to do with the antenna. Make sure you have knocked it by mistake
Sent from my GT-I9100 using xda app-developers app
I experienced the same problem with my Samsung S2. I had destroyed the charging port by being careless when charging it which meant my phone would not charge at all; although if I was lucky I would get about 10% charge every day.
To resolve the problem, I bought a cheap charging port flex cable off ebay for about £4.00 which I thought was a bargin. After taking the phone apart (with help from a YouTube video) I replaced the port, turned the phone on and it charged perfectly. Then all of a sudden I lost all signal. I moved around the house, hoping to get the slightest bit of signal but no, nothing. I did a lot of research online as to why this has happened and everyone said it was to do with the antenna cable that runs along the left hand side of the phone so my immediate thought was to buy a new one. I did a factory reset to see if that helped but it did not. As I was desperate, the following day I went into town to see if I could find a shop that sold an antenna wire. I went in shop after shop but nowhere sold what I was looking for. I went into a shop and described my problem to the man behind the counter, and he knew exactly what was wrong. On the flex cable there is "REV" followed by a number, and he told me that if the replacement number is not the same as the original then the phone will have no service.
In the photos you will see my original cable that was "REV2.3" and my replacement cable that was "REV2.2".
Long story short... when replacing the charging port make sure the replacement flex cable has the same REV number as the original otherwise you will have no service. Your problem is not related to the antenna wire.
I hope this helps!
solution posted here
http://forum.xda-developers.com/galaxy-s2/help/weak-signal-reception-changing-micro-t1950114/page4
Hello,
A few weeks ago, I replaced my screen because my smartphone had fallen. When disconnecting the antenna cable, the coax connection on the PCB was broken. So I ordered a new PCB. However, with the new PCB, I no longer have any coverage. Is it possible that the PCB is not suitable for the European / Belgian network (GSM/Edge/3g/lte). I also noticed that the PCB I received differs a lot from the design that was in my smartphone. The PCB under the smartphone is the defective PCB, the mounted PCB is the PCB is the new PCB. You can find a picture here: https://imgur.com/Wzmq0p0 When my broken screen was still on the smartphone, I had full range and there was nothing wrong with the network. The connections of the cable is also not damaged: https://imgur.com/H4WkFmA Screenshot of no coverage, but SIM card data that is read: https://imgur.com/tkOhXI9 I tested 2 sim cards that I in the Pocophone. Both are from another provider. Neither got a signal. In my other smartphone, both SIM cards were connected to the network and worked as expected. Does somebody know if I ordered the wrong PCB foe Belgium?
Are you certain that the antenna cable is good?
If it's damaged the sim should show up but with no network at all. (Exactly the behavior that you're having)
---------- Post added at 11:30 PM ---------- Previous post was at 11:26 PM ----------
The chips' small differences are normal between an aftermarket and an original imo
ablivian said:
Hello,
A few weeks ago, I replaced my screen because my smartphone had fallen. When disconnecting the antenna cable, the coax connection on the PCB was broken. So I ordered a new PCB. However, with the new PCB, I no longer have any coverage. Is it possible that the PCB is not suitable for the European / Belgian network (GSM/Edge/3g/lte). I also noticed that the PCB I received differs a lot from the design that was in my smartphone. The PCB under the smartphone is the defective PCB, the mounted PCB is the PCB is the new PCB. You can find a picture here: https://imgur.com/Wzmq0p0 When my broken screen was still on the smartphone, I had full range and there was nothing wrong with the network. The connections of the cable is also not damaged: https://imgur.com/H4WkFmA Screenshot of no coverage, but SIM card data that is read: https://imgur.com/tkOhXI9 I tested 2 sim cards that I in the Pocophone. Both are from another provider. Neither got a signal. In my other smartphone, both SIM cards were connected to the network and worked as expected. Does somebody know if I ordered the wrong PCB foe Belgium?
Click to expand...
Click to collapse
some blue resistor is missing in new one, i think!
The antenna was damaged a bit, but i also ordereda new one with the damaged one worked.
Because the antenna cable of the pocophone was out of stock, i ordered another one from xiaomi. It was a little bit longer but, still the same issue
ablivian said:
The antenna was damaged a bit, but i also ordereda new one with the damaged one worked.
Because the antenna cable of the pocophone was out of stock, i ordered another one from xiaomi. It was a little bit longer but, still the same issue
Click to expand...
Click to collapse
In the pic it seems like the antenna cable is a bit smashed by the bezel when it was screwed together. You could try with another cable and test for signal before reassembling the phone.
I made 2 movies to show that there should be a difference and that the issue is not the antenna cable.
In this movie, I installed the new PCB and there is no networkconnectivity:
HTML:
https://youtu.be/0xNUxfh3CXM
In this movie, I installed the PCB without COAX-connection for the antenna, but just tape. I'm using is now with tape for about 5 days:
HTML:
https://youtu.be/NIRFgzkucUk
Does anyone have an idea, where to fine the correct PCB to use in Belgium (Europe)?
I contacted the company, but they only say they buy it from "Iparts Buy".
Any help would be appreciated.
Did you ever get this issue resolved. I'm having the same problem
Hey
Here is a link to a trusted shop in Germany (mobiltec24). I can't post a link. I'm a new member.
I have the same problem as you. I am also looking for a solution. I buy a pocophone without mobilenetwork. I can't unlock the bootloader without SIM Card.
Having the same issue, any update ?