Related
I am new to the Android platform so please excuse any silliness on my part…
Below are the steps I took to successfully allow my Vizio Tablet (VTAB108) to connect via USB using the generic Google ADB driver as Vizio does not include ADB access for the tablet.
History:
I am trying to Root my tablet and from what I read throughout the forum, the easiest steps to root a tablet is using the SuperOneClick method.
Since SuperOneClick requires ADB access and the Vizio does not include the ADB driver (and the generic Google) do not work out of the box I was at a loss to how I would run SuperOne Click.
This article are the steps I took to get ADB access working with Windows 7 x64 and the Vizio Tablet.
I am hoping my steps here can further lead to root access for this tablet.
As an FYI, I was still unsuccessful in getting SuperOneclick to completely run after following these steps, but maybe someone has an alternate method of rooting now that ADB access is available? /me crosses fingers
It would stop at Step #6 at which time I would disconnect and reconnect the tablet. It would contine to step #8 but then finally fail. If anyone has an alternative to SuperOneClick, I would gladly try it.
IMPORTANT:
The instructions below assume you have already put your Tablet into USB debugging mode.
The instructions below assume you are running Windows 7 x64. If you are running x32 versions of your OS, modify the below settings as apporopriate for your OS[/B].
1. Download and install the Google Android SDK.
(Being this is my first post, I cannot post a URL so google the following topic exactly and click the first link):
what-is-adb-and-how-to-install-it-android
2. When you get to the USB driver install you will have to manually modify your android_winusb.inf settings file to allow Windows to recognize your Vizio Tablet using the generic Google ADB-USB driver.
3. Find the "usb_driver" folder in your sdk directory. (Mine was: C:\Program Files (x86)\Android\android-sdk\extras\google\usb_driver).
4. Right-click "android_winusb.inf" and open it with notepad or your favorite text editor.
Under the [Google.NTamd64] section, paste the following:
Code:
;Vizio Tablet
%SingleAdbInterface% = USB_Install, USB\VID_0489&PID_E040&MI_01
%CompositeAdbInterface% = USB_Install, USB\VID_0489&PID_E040&REV_0227&MI_01
then, open a command prompt and type the following:
Code:
echo 0x489 >> "%USERPROFILE%\.android\adb_usb.ini"
5. Right-Click the unknown device in Windows Device Manager (Under Other devices) and manually install the driver for your Tablet.
NOTE: Originally my tablet connected to the computer and installed the regular Windows 7 Mass Storage driver. I had to remove this driver before I could see the device listed under "Other Devices". Follow these instructions if you need to remove your generic Mass Storage driver:
Code:
A. Unplug all removable devices (USB drives, Thumb Drives, SD Cards, Etc...) but leave the Android phone plugged in.
B. Open Windows Device Manager.
C. Select "Universal Serial Bus Controllers"
D. Select USB Mass Storage Device.
IMPORTANT: Click on the details tab and select "Compatible Ids" under the Property drop-down. You should see three items listed under Value. If not, you are looking at the wrong Mass Storage Controller.
E. Select Uninstall Driver
F. Close the window.
G. Right-Click your computer name at the top of device manager and select "Scan for Hardware Changes".
H. Your new "Android Phone USB device" with a Yellow Exlamation mark! will appear under Other Devices.
I. Click on the "Android Phone USB device"
J. Select "Update driver software"
J. Select "Browse my computer for driver doftware"
K. Browse for the location that you have unzipped the android_usb_windows ( Mine is: C:\Program Files (x86)\Android\android-sdk\extras\google\usb_driver )
6. Now test to make sure you can access your device in USB Debug mode:
Type the following from a command prompt:
adb kill-server
adb devices
You should see your device serial number at the command prompt and in Windows Device Manager if everything worked.
drivers
USB Drivers have been posted on the vizio support website for Intel and for AMD. Are they crucial to what you want to do about rooting?
USB Drivers Not Installing
[email protected] said:
USB Drivers have been posted on the vizio support website for Intel and for AMD. Are they crucial to what you want to do about rooting?
Click to expand...
Click to collapse
I grabbed those drivers a couple of days ago and could not get Win7 or WinXP to install them with the vtab1008.
I can use adb to interface with the vtab008 (using Linux and Win7), but GingerBreak and SimpleOneClick (which uses GingerBreak) are unable to root the vtab1008.
I've been pestering Vizio about the downsides of the tablet. Coming from a rooted Nook, there are some things about the vizio i really like. It's a nice build at an attractive cost. If I can get netflix and hbo go working, a better remote app and a more logical system of using the sd card, I would keep it. Otherwise it goes back to Costco on the 89th day after purchase.
Agreed
[email protected] said:
I've been pestering Vizio about the downsides of the tablet. Coming from a rooted Nook, there are some things about the vizio i really like. It's a nice build at an attractive cost. If I can get netflix and hbo go working, a better remote app and a more logical system of using the sd card, I would keep it. Otherwise it goes back to Costco on the 89th day after purchase.
Click to expand...
Click to collapse
This is my thinking EXACTLY!
[email protected] said:
I've been pestering Vizio about the downsides of the tablet. Coming from a rooted Nook, there are some things about the vizio i really like. It's a nice build at an attractive cost. If I can get netflix and hbo go working, a better remote app and a more logical system of using the sd card, I would keep it. Otherwise it goes back to Costco on the 89th day after purchase.
Click to expand...
Click to collapse
Yes, I agree. If there's no root, the tablet is not worth it.
The drivers worked for me.
I downloaded the drivers from the Vizio site and when I plugged the VTAB into my computer I manually installed the driver. I just used adb to grab a bunch of screenshots.
OP worked for me (without the mass storage issue)
Code:
adb reboot bootloader
just did a true reboot
Code:
adb reboot recovery
got me the exclamation mark and the "Home" button brought me to a recovery screen where it would let me flash signed updates or cache/full wipe the device.
You can get to recovery mode by holding down both volume buttons and the power button. Details
I cant even get the drivers to install. I've did a right click on the .inf file and it will not install. Any Ideas?
Thanks
Mark
Mark0266 said:
I cant even get the drivers to install. I've did a right click on the .inf file and it will not install. Any Ideas?
Thanks
Mark
Click to expand...
Click to collapse
DL the drivers from the Vizio site. Turn on USB debugging on the VTAB. Plug the VTAB into your computer. When the install driver prompt comes up follow the steps to install a driver from a specific location and point it to the driver you downloaded. The steps will vary depending on the version of windows you are running.
marvin02 said:
DL the drivers from the Vizio site. Turn on USB debugging on the VTAB. Plug the VTAB into your computer. When the install driver prompt comes up follow the steps to install a driver from a specific location and point it to the driver you downloaded. The steps will vary depending on the version of windows you are running.
Click to expand...
Click to collapse
Thats the problem the prompt never comes up. Running Windows 7
Well I got the driver for adb to install but it still will not show up when I do adb devices
Bootloader?
the.joeba said:
OP worked for me (without the mass storage issue)
Code:
adb reboot bootloader
just did a true reboot
Code:
adb reboot recovery
got me the exclamation mark and the "Home" button brought me to a recovery screen where it would let me flash signed updates or cache/full wipe the device.
Click to expand...
Click to collapse
Did you actually get into the bootloader? adb reboot bootloader simply reboots the device for me.
So whats with gingerbreak? No love with it? I thought this thing was rooted already prior to shipping? Hmmm. My bro just ordered one for me and I am curious about getting it rooted. Lets get this thing rooted and overclocked and get it some love. Also, whats the word on honeycomb on this beast? anything?....
Mark0266 said:
Well I got the driver for adb to install but it still will not show up when I do adb devices
Click to expand...
Click to collapse
Same here.
Rooting help
I have some coding knowledge, but have never worked on rooting a device. I did not pay for mine, so if anyone has references to some info I can look at about obtaining root then I will work on mine without fear of bricking it.
I have been at this for weeks, to no avail.. tried changing params in Gingerbreak, tried running it under every condition possible, and the only thing I haven't tried is changing how GingerBreak is using the /sdcard/ mount point, as that's where the internal memory is mounted to.. It's a pretty odd move to make, and I don't like having my true sdcard in /sdcard/external. what a crock :/
This tablet has to have a way to be rooted, I tried an older version of gingerbreak 1.1 just kept running, never failed, but didn't root the tablet just kept running, like it was gonna root the tablet, kinda weird, I do know that the bootloader is not locked down, my wife works for vizio, the company gave there employees a tablet for free
(I cannot post links at this time, a quick Google Search or a look at the Topic titled "Full Root")
The goal of this guide:
I rooted my family members Nook last night but got hung up for a few hours trying to get the ADB Drivers enabled. This is how I made it work. This guide will be expanded and improved once I have my own Nook Tablet (Jan 12th).
Things you need:
• Nook Tablet (Duh)
• USB cord to go between NT and Windows PC
• PC with Windows installed (Tested on XP and x64 Windows 7)
• TGPS_Launcher.apk Installed to your Nook
• ADB USB Drivers for Nook Tablet Extracted to C:\Ntroot on your PC
• USBDeView open on the Windows PC
Step 1:
Ensure that your Nook is version 1.4.0 and not 1.4.1. (I will expand this step later when I have a nook in my hand, I suggest a Google search if you do not know how to do this)
Step 2:
Find this thread on your Nook and download the TGPS_Launcher.apk to your device, then install it. This is well covered in many other threads. (Will expand this step when I have a nook in my hand)
You should now be able to allow USB Debugging, and disable Auto Mount. These settings can sometimes change without your permission, so always uncheck and recheck them to ensure they are properly set.
Step 3:
Plug in your Nook to your PC. Your nook should still respond to your commands, if it tell you in USB Mass Storage mode, then retry Step 2.
Go into your Device Manager. If your Nook shows up with a yellow explanation mark indicating an Error, then you’re in business and really don’t need this guide. All you need to do is update drivers from the file C:\Ntroot. However, assuming that your Nook shows up under Disk Drives and USB Mass storage, then ADB wont be able to see your Nook, please keep reading.
Step 4:
Time to start the USBDeview utility. This utility will open to a list of almost all the drivers your computer has for USB Devices. We are going to uninstall a few of them, namely anything that says “Android” “Nook” or in my case, “Motorola”. You do not need to remove any that specify ADB.
Near the top right hand side, you can sort drivers by when the device was last connected. Do this, then remove any utilities used when you plugged your nook in. Done? Ok, time to see if your work was for nothing.
Step 5:
Make sure once again that USB Debugging is turned on for your Nook. Unplug the Nook, then Unchecked USB Debugging and Check it again. Now plug your device back in and check in Device Manager. You will hopefully see one of two things:
A: You will see your nook with a yellow error icon next to it, which means you just need tell it to update from C:\Ntroot.
B: At the top of the device manager you will see Android Devices, and your nook will show up as Android Composite ADB Interface
If your Nook is still showing under disk drives and mass storage, then try steps 3 and 4 again. Still having trouble? Do a factory reset and try again from step 1.
You should now be able to run your rooting program!
(I feel this should be in the Dev forum, but this is my first post and I was not allowed. Perhaps a mod would like to move this topic?)
I plan on purchasing my own Nook on the 12th on Jan, at which point I will add pictures and expand on my guide. This guide is written from memory and will be edited and improved.
Please consider this guide an Alpha Version
Good write up!
The procedure worked fine on my laptop. When I did it on on my home PC I forgot to disable auto-mount and the Nook installed itself as mass storage. I was able to right click -> un-install all the USB Mass Storage entries (with the Nook unplugged), disable auto-mount, plug the Nook back in, and have it show up correctly.
In short, I did not need to use "USBDeView" as I was able to remove the diveres manually. I suppose if you have more than a handful for USB devices (I just have a Mouse, Keyboard, and printer) "USBDeView" might be helpful to determine which drivers to un-install...
The device manager is enough for most people, but there is a somewhat large number of us that are having trouble still. Possibly because of other devices we have installed before. (I dont understand how all the drivers work and I wont pretend to)
Some people have go so far as putting a fresh install on Windows on a partition of a PC.
I had this problem with both my laptop and my desktop, which surprised me. This worked on both the laptop and PC, so hopefully it can help other people.
I cant wait to get my own tablet on the 12, I will take lot of pictures and make this process more user friendly.
I did all of the steps several times and I still get WPD Driver for the portable device and mass storage for my Nook Tablet. I am guessing I am up a river without a paddle right now.
I will try it in Linux and/or try it on someone's Windows machine.
I am trying to install the drivers from Google's SDK package. So I browse to the correct folder, but device manager says "windows could not find driver software for your device".
Any suggestions? Is there any other set of drivers specifically for NT?
mtelesha said:
I did all of the steps several times and I still get WPD Driver for the portable device and mass storage for my Nook Tablet. I am guessing I am up a river without a paddle right now.
I will try it in Linux and/or try it on someone's Windows machine.
Click to expand...
Click to collapse
Did you sort by last time plugged in and delete all of those too? Have you re-checked and then re-un-checked automount/usb debugging and such?
This is interesting, you'll have to come back and let me know if you ever get it working on your PC. Maybe its a good excuse for a nice healthy re-format and reinstall of windows?
l3ft3r1s said:
I am trying to install the drivers from Google's SDK package. So I browse to the correct folder, but device manager says "windows could not find driver software for your device".
Any suggestions? Is there any other set of drivers specifically for NT?
Click to expand...
Click to collapse
I don't know if they are different, but I used the drivers specificly from the thread about rooting the NT. [I would post a link, but I'm typing from my phone]
You have the yellow error mark next to your device? If so you've almost got it!
The_Joe said:
I don't know if they are different, but I used the drivers specificly from the thread about rooting the NT. [I would post a link, but I'm typing from my phone]
You have the yellow error mark next to your device? If so you've almost got it!
Click to expand...
Click to collapse
Yeap, that did the trick, thanks. Drives installed successfully this time, but adb devices still returns nothing.
Thats very odd. It shows up in device manager as an ADB device?
If so, please try the NookandZergy file, then copy the results so we can try to farther assist
What devices have you rooted before?
I cannot help but feel I will be 100x more useful in a week when I have my device in hand...
adb error: device offline
This drove me nuts for at least a day. Turns out it is what happens when you are plugged into a USB 3.0 port on your PC side. Find out which USB is 2.0 (Front Panel for ZT Systems), use it and life suddenly gets really good.
The_Joe said:
Thats very odd. It shows up in device manager as an ADB device?
If so, please try the NookandZergy file, then copy the results so we can try to farther assist
What devices have you rooted before?
I cannot help but feel I will be 100x more useful in a week when I have my device in hand...
Click to expand...
Click to collapse
At last, after many different things I tried, I am getting a response to adb devices!
I tried disabling and uninstalling usb devices, uninstalling java 7 and installing java 6, re-installing android sdk, at last it worked. Sorry, I can't guess what the problem was :/
l3ft3r1s said:
At last, after many different things I tried, I am getting a response to adb devices!
I tried disabling and uninstalling usb devices, uninstalling java 7 and installing java 6, re-installing android sdk, at last it worked. Sorry, I can't guess what the problem was :/
Click to expand...
Click to collapse
The problem is sdk uninstall and use ccleaner to clean your PC and registries. Use the drivers provided in this forum
Sent from XDA using one of my Android Toys
Edited post to: Sorry to bother anyone, I found the problem. Thank you all for helping!
Well I have done everything and still get permission denials for copying and chmod on my Nook Tablet.
Took the Nook to work and tried it on a fresh machine. Everything went great. Drivers installed and everything ready for usb debug and non-automount and then I run into the same permission errors and being denied access to the folder for Zerk and no chmod.
Same issue no matter what machine. What is wrong with my tablet? I am re-rooting it from being automatically upgrade to 1.4.1. I get it to 1.4.0 with the SD card restore.
LadyPenley said:
Edited post to: Sorry to bother anyone, I found the problem. Thank you all for helping!
Click to expand...
Click to collapse
In the future don't delete your original, just post an edit with the fix. That way when someone else has a similar problem your post can help.
Sent from my BNTV250 using xda premium
mtelesha said:
Well I have done everything and still get permission denials for copying and chmod on my Nook Tablet.
Took the Nook to work and tried it on a fresh machine. Everything went great. Drivers installed and everything ready for usb debug and non-automount and then I run into the same permission errors and being denied access to the folder for Zerk and no chmod.
Same issue no matter what machine. What is wrong with my tablet? I am re-rooting it from being automatically upgrade to 1.4.1. I get it to 1.4.0 with the SD card restore.
Click to expand...
Click to collapse
Did you find a solution? Thats a problem I sadly dont know how to help with. I would start with:
-Check USBDeview and delete anything android/Nook/usb related. Delete just about everything.
-Restart the device
-Uncheck and recheck the USB Debugging boxes
-Recheck and uncheck the auto-mount box
-Test
-Try a different USB Port
-Try another PC
Thanks but didn't work.
thanks, Joe. I did exactly as you mentioined below and had the Android/Nook appear at the top of the Devices listing. However, the adb command still can't find the device. Any suggestions?
Stan White
*****************
The_Joe said:
(I cannot post links at this time, a quick Google Search or a look at the Topic titled "Full Root")
The goal of this guide:
I rooted my family members Nook last night but got hung up for a few hours trying to get the ADB Drivers enabled. This is how I made it work. This guide will be expanded and improved once I have my own Nook Tablet (Jan 12th).
Things you need:
• Nook Tablet (Duh)
• USB cord to go between NT and Windows PC
• PC with Windows installed (Tested on XP and x64 Windows 7)
• TGPS_Launcher.apk Installed to your Nook
• ADB USB Drivers for Nook Tablet Extracted to C:\Ntroot on your PC
• USBDeView open on the Windows PC
Step 1:
Ensure that your Nook is version 1.4.0 and not 1.4.1. (I will expand this step later when I have a nook in my hand, I suggest a Google search if you do not know how to do this)
Step 2:
Find this thread on your Nook and download the TGPS_Launcher.apk to your device, then install it. This is well covered in many other threads. (Will expand this step when I have a nook in my hand)
You should now be able to allow USB Debugging, and disable Auto Mount. These settings can sometimes change without your permission, so always uncheck and recheck them to ensure they are properly set.
Step 3:
Plug in your Nook to your PC. Your nook should still respond to your commands, if it tell you in USB Mass Storage mode, then retry Step 2.
Go into your Device Manager. If your Nook shows up with a yellow explanation mark indicating an Error, then you’re in business and really don’t need this guide. All you need to do is update drivers from the file C:\Ntroot. However, assuming that your Nook shows up under Disk Drives and USB Mass storage, then ADB wont be able to see your Nook, please keep reading.
Step 4:
Time to start the USBDeview utility. This utility will open to a list of almost all the drivers your computer has for USB Devices. We are going to uninstall a few of them, namely anything that says “Android” “Nook” or in my case, “Motorola”. You do not need to remove any that specify ADB.
Near the top right hand side, you can sort drivers by when the device was last connected. Do this, then remove any utilities used when you plugged your nook in. Done? Ok, time to see if your work was for nothing.
Step 5:
Make sure once again that USB Debugging is turned on for your Nook. Unplug the Nook, then Unchecked USB Debugging and Check it again. Now plug your device back in and check in Device Manager. You will hopefully see one of two things:
A: You will see your nook with a yellow error icon next to it, which means you just need tell it to update from C:\Ntroot.
B: At the top of the device manager you will see Android Devices, and your nook will show up as Android Composite ADB Interface
If your Nook is still showing under disk drives and mass storage, then try steps 3 and 4 again. Still having trouble? Do a factory reset and try again from step 1.
You should now be able to run your rooting program!
(I feel this should be in the Dev forum, but this is my first post and I was not allowed. Perhaps a mod would like to move this topic?)
I plan on purchasing my own Nook on the 12th on Jan, at which point I will add pictures and expand on my guide. This guide is written from memory and will be edited and improved.
Please consider this guide an Alpha Version
Click to expand...
Click to collapse
whitets said:
thanks, Joe. I did exactly as you mentioined below and had the Android/Nook appear at the top of the Devices listing. However, the adb command still can't find the device. Any suggestions?
Stan White
*****************
Click to expand...
Click to collapse
I had literally this exact same problem the 6th time I restored and flashed. IF im right, you just need to uncheck then recheck usb debugging.
Let me know if it works!
Thanks to a good link from Vanto to read here is the instructions as to how I got it to work,
This solved it for Winblows 7 64 bit. For others having the same problem on Winblows 7 64 bit (should be the same for 32 bit miuns the X86 Directory)
1. Go into settings on the prime and make sure USB debugging has a check in it in under SYSTEM > Developer options > USB Debugging
2. Plug your prime into your Winblows 7 laptop and let it install its drivers. Open up device manager by going to Start > Control Panel > Hardware and Sound > and click on device manager under devices and printers. If you see at the top of device manager ASUS Android devices and when you expand it you see ASUS Android Composite ADB Interface you already have the ADB drivers installed and can skip down to #6
3. Go to ASUS website and download the USB drivers for the TF201. Download Vipermod Primetime 4.6 here for the ADB drivers http://goo.im/devs/viperboy/Prime/viperMOD_PrimeTime_v4.6.zip then extract the zip file to a normal file. You only need the drivers from the tool.
4. Plug your prime into your Winblows 7 laptop and let it install its drivers. Open up device manager by going to Start > Control Panel > Hardware and Sound > and click on device manager under devices and printers.
5. You should see the prime listed under portable devices. Uninstall the driver then update the driver manually. Browse to the folder you created from the Vipermod primetime zip. Make sure there is a check in check sub folders. Winblows should detect the drivers and then convert the prime to a ASUS Android Device.
6. Go into settings on the prime and make sure there is no check in Launch ASUS Sync under PERSONAL > Accounts & Sync > Launch ASUS Sync
7. Press Control, Shift, Escape at the same time and make sure there are no instances of ASUS Sync or Splashtop runnung in services in Winblows 7.
8. Download and Install the latest Android SDK. I installed all the libraries and such just to be on the safe side. http://developer.android.com/sdk/index.html
9. DISCONNECT YOUR PRIME FROM THE USB AND REBOOT YOUR PRIME AND YOUR WINBLOWS LAPTOP. After both devices reboot plug in your tablet into your Winblows laptop.
10. Navigate to C:\Program Files (x86)\Android\android-sdk\platform-tools and click on the ADB file. A command prompt will open and spool up a bunch of stuff then close. All the stuff spooling I am assuming was the ADB server starting.
11. Hold down shift then right click inside platform-tools folder and select open command prompt here. You should be in a command prompt window showing the directory C:\Program Files (x86)\Android\android-sdk\platform-tools
12. type adb devices. You should see your primes serial number pop up.
13. make a test file in the platform-tools directory, i just used a simple text file to test then type:
adb push test.txt /sdcard/
It would be easier to just put the Rom you are going to flash in this directory so when it is time to push the rom it would be:
adb push nameofrom.zip /sdcard/
If SDCARD not recognized try:
adb push nameofrom.zip /system/media/
14. browse to your sdcard and you should see your file there. If you are already in the sdcard folder window on your prime, leave the folder then come back and it should be there.
15. You should be able to push files now after superwiping. You may need to push to /system/media/ if /sdcard/ is not found. Make sure you have all the / in the directory structure when pushing.
16. From inside recovery select install zip from sdcard and browse to the folder you pushed it to then flash away.
If anything seems incorrect or out of order please let me know so I can correct it. If this helps you congrats but if not I'm sorry. This is how I got it to work.
As you have stated that prior to your windows re-install, everything had worked, thus I highly doubt that this could be the issue... but just to double check, you do have usb debugging enabled, right?
If you can, connect your transformer prime, and try executing {install directory}/android/platform-tools/adb.exe -devices and let us know what kind of output you get.
Lostsorrow said:
OK looking for a little help here. I am planning on doing the Super mega wipe in the dev section however ADB has not recognized my prime. I wanted to verify I could push to it a test file before I did the wipe. Under device manager it shows the whole Asus ADB interface device and that the device is "working properly" I also have a listing down in portable media devices where it states Transformer TF201. I have disabled Asus sync and do not have splashtop. When I connect my prime I can explore the internal SD and copy files back and forth over USB. I have also installed and updated the latest Android SDK. I am at a total loss here. I recently did a fresh install of windows and beforehand it used to work. Any ideas or help would be greatly appreciated. Thanks in advance :cyclops:
Click to expand...
Click to collapse
make sure your adb files are the most updated once,
i had this problem before but thats just cause my adb was not updated
I recently battled with this and concluded that adb just doesn't work on Windows 64bit for the TFP. My advice, try to find an XP pc and do it through that. I posted in Prime_Full_Wipe thread in Dev section about this.
Wasted several hours trying to get adb to see the device. Tried so many device drivers.... Latest adb versions etc....
Sent from my EPAD using Tapatalk 2
tangiers said:
I recently battled with this and concluded that adb just doesn't work on Windows 64bit for the TFP. My advice, try to find an XP pc and do it through that. I posted in Prime_Full_Wipe thread in Dev section about this.
Wasted several hours trying to get adb to see the device. Tried so many device drivers.... Latest adb versions etc....
Sent from my EPAD using Tapatalk 2
Click to expand...
Click to collapse
thats weird... im on window 7 64 bit and it works for me ;o
lil-devil said:
thats weird... im on window 7 64 bit and it works for me ;o
Click to expand...
Click to collapse
Mine did too when I unlocked but once I had a custom rom on it, it stopped working. I think the driver gets messed up by the custom rom making the pc see the TFP as something different to an Asus TFP.....
Sent from my EPAD using Tapatalk 2
http://forum.xda-developers.com/showthread.php?p=28021373 is my post or you can try read the whole thread, it helped me a lot
Just did my Full-Wipe part on a brand new Win7 Ultimate-SP1 x64 machine
Sent from my GT-I9000 using Tapatalk 2
unlocking phone from one network
hae guyz i have my htc s620 upgraded from dash have tried to generate network unlock code and for 3days of hard work and going through almst all threads nothing has been fruitful......i need someone who will help me generate unlock code...my pc is window 7 and my phones imei is 35155301530476202........i will be so greatful..email me the unlock code via [email protected]
waiting for u reply guyz
I have used many different methods to root phones even a few tablets for friends. But I have bought a HKC 7 inch tab from walmart. Great starter tablet by the way. I have found no information what so ever on any forum about this model. It has decent processor power and runs rather smooth. Alas there is no way to root this thing to reach its full potential. I checked around on the net and found nothing, none of the one click apps work on this model. Adb does not recognize the tablet either. I've put in the tablet ID into the adb_usb.ini still no device found. I'm not looking for anyone to just hand me the root process on a silver plater, though that would be nice, but any help moving me in the right direction would be appreciated.
I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment Rockusb.rar
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon
Krytical said:
I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment 1468367
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon
Click to expand...
Click to collapse
Thanks for the info. Will be giving it a go later today
Krytical said:
I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment 1468367
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon
Click to expand...
Click to collapse
when in doubt go back to the forums. I can not get the inf in the rockusb to install. "Installation for this file type not permited" . So I'm stuck, the program will not complete. I'm on windows 7 so maybe the driver is for another system. If you can provide futher help, Thanks in advance.
New approach
Ok I cannot get the drivers to install on my computer. Window 7 seems to default to its own driver and will not let me install the rockusb drivers.
With that said, I have the system Update.img and was wandering if the img itself can be rooted and then updated to the tablet. If this is possible and anyone with the knowledge is willing I will upload it. Or if someone is really patient and would like to walk me through the process and I will attempt to do this myself
No Help
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.
tannerjames said:
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.
Click to expand...
Click to collapse
Can't tell your level of PC knowledge so if you already know this don't get offended. The .inf is editable and there are areas in there that allow manufacturers to prevent installation on some OS's to prevent conflicts. Make a system restore point or better yet a backup and then post the contents of the INF somewhere and point the folks here to it and they may be able to help you edit it to install. Regardless, you'll have to use the "have disk" option instead of letting windows search for a driver even if you get the edits right. And the usual disclaimers about me not being responsible for any issues with your equipment as a result of this are in effect.
tannerjames said:
So with no help I assume this is dead. I have a usb driver package with an .inf file a .sys file and a .cat file but this will not install on my computer thus leaving without a clue and no help. Have seached for a way to force install this driver command line install right click and install the inf. Nothing works so if someone wants to throw me a bone, thanks, if not I guess this thread is dead.
Click to expand...
Click to collapse
I was able to root using the instructions above although i don't think you need the rockusb drivers. You just need the usb drivers that come with the android sdk. I am on Win 7. Thanks for the above info for rooting.
I was able to install ROM manager and now proceeding to backup ROM and upgrade using this guide: cant post link as forum is preventing, but search for rom flash guide on androidpolice com.
Hope this helps.
Big thanks to this thread to get me going...!!!
?
could someone please, Barney style, Explain how I am supposed to select the android_winusb.inf because my steps are as follows. Right click on device p771a in device manager, browse my computer, let me pick from a list of device drivers, have disk, point to the google usb driver (C:/Android/android-sdk/extras/google/usb_driver) select the android_winusb.inf open. Hit ok, (The folder you specified doesn't contain a compatible software driver for you device. If the folder contains a driver, make sure it is designed to work with windows for x64-based systems). Hope this helps explain my troubles. Glad that my thread is helping others to root this device but it does not work for me.
Could it really be that simple?
Found in another forum about the nexus 7 when connected to the pc there is a presistent notification that allows you to change the connection type from mpt to camera which will give you adb access and the tool from this thread works great. Thanks for the help guys, got my root on
tannerjames said:
Found in another forum about the nexus 7 when connected to the pc there is a presistent notification that allows you to change the connection type from mpt to camera which will give you adb access and the tool from this thread works great. Thanks for the help guys, got my root on
Click to expand...
Click to collapse
Glad you could figure it out...
I was not able to use the ROM Manager to backup the ROM since the device is not supported on this tool, but see below for how you can obtain the stock image.
I've tried to flash multiple different ROMs using RKAndroid to the tablet, spending days on this, with no success. The tool itself works great and I am able to flash the ROMs since it supports the RK29 chipset which I believe this tablet has. The stock ROM for this device is available from the manufacturers web site (the link is available when you go to Settings => About Device => System Update, hkcdigital dot com slash update slash update.img), if anyone would like to take the stock rom and upgrade it to Android 4.2/JB.
I was able to unpack/repack the stock image using the wendal image tools and modify / cook the ROM using Android kitchen method described elsewhere in this forum. Rockchip Batch Tool is another great utility to flash custom ROMs to this device. Also, If you put the ROM as update.zip or update.img file on the microSD card, the tablet will take it and flash the image as long as it is in the right format. Ofcourse you can put the tablet into recovery and restore from there as well. I've found that the stock image (update.img) has the following file/folder format when unpacked: /RK29xxLoader(L)_V2.27.bin, /package-file, /parameter, /recover-script, /update-script, /Image/boot.img, /Image/system.img, /Image/recovery.img and /Image/misc.img.
Is it possible to upgrade this tablet to Android 4.2 or atleast Jelly Bean? Would be very helpful if someone is able to do this. The most success I've had so far is with the custom ROM Oma_Odys_Loox_JB_4.1.1_v1.2.2a flashed using RKAndroid. It flashed the tablet fine, updated the boot etc. On tablet boot I am able to see the new logo, but then the it doesn't go anywhere from there. I think customizing this ROM or the stock ROM we should be able to get the new OS on to the HKC tablet. I've given up for now since I don't have the time to spend on this anymore. If someone is able to do this, please post the instructions or upload the custom ROM, as I am sure it will benefit a lot of people and will be much appreciated. Happy cooking!
Thanks!
jawadshaik- rom manager
If you have successfully flashed rom manager on this device could you post the steps you took to do so. What version? Manual flash? The program itself says there is no recovery for this device.
Sorry jumped the gun on that last post. Thanks for the info
What's the secret to keeping the battery from draining so quickly while it's idle? I just got this and see it drained about 40% in about 2 hours I think and I wasn't using it.
tannerjames said:
I have used many different methods to root phones even a few tablets for friends. But I have bought a HKC 7 inch tab from walmart. Great starter tablet by the way. I have found no information what so ever on any forum about this model. It has decent processor power and runs rather smooth. Alas there is no way to root this thing to reach its full potential. I checked around on the net and found nothing, none of the one click apps work on this model. Adb does not recognize the tablet either. I've put in the tablet ID into the adb_usb.ini still no device found. I'm not looking for anyone to just hand me the root process on a silver plater, though that would be nice, but any help moving me in the right direction would be appreciated.
Click to expand...
Click to collapse
@jawadshaik
Just out of curiosity, when you were flashing that Rom that brought up the boot screen, did you do a wipe/factory reset from recovery mode before flashing? I have no idea if that would help or not, but most if not all roms require a data wipe before flashing... Just curious if you had tried this as I have heard of this happening on other devices because a data wipe wasn't done first. Might be worth a shot if you haven't tried it already, just a thought
Sent from my Huawei u8651s using xda app-developers app
Krytical said:
I rooted one of these for a friend at work,
sourceforge.net/projects/androidroot/ is the root that I got to work.
and I've attached the driver that the manufacturer provided me when I requested a driver for development purposes.View attachment 1468367
Here is how I got it rooted
1. Installed Java JDK and Android SDK.
2. downloaded and extracted Manufacturer driver from Rockusb.rar and right clicked on the .inf file and selected install.
3. Opened Android SDK manager, installed Android SDK for version of tablet, and SDK tools, and Google usb driver from extras.
4. Enabled usb debugging mode on the tablet, and enabled unsigned apps to be installed.
5. Connected the tablet via USB
6. when the tablet shows up in the device manager as P771A I selected to update the driver manually, and selected the google USB driver from the android SDK.
7. Downloaded and extracted the android root I listed above.
8. Run android root and when it says "press any key to continue" it is waiting until the device connects to the computer again, as it could be rebooting, and one time when the tablet reboots, there is no text, just a black screen, but it does eventually connect and you can continue.
Also. I extracted the root to my desktop. when I ran as admin, it did not work, because the files were not on the administrators desktop, only mine, so it might be a good idea to extract the root to C:\ drive, so if you need to use admin, it won't fail
hope this helps
-Brandon
Click to expand...
Click to collapse
So after doing working on this a while, I've finally figured it out. Here are some caveats:
1. You can't do this on a Mac or Linux box. Don't ask me why, you just cant.
2. You have to turn on USB debugging, change the Security to allow Unknown sources and MOST IMPORTANT: when you plug it in, you have to change it to "Connected as a Camera". Putting it in storage mode doesn't work!
HOW TO INSTALL THE PROPER DRIVER & ROOT THE DEVICE:
1. Follow the steps quoted above and download the Google Android SDK, and the Java JDK (from oracle.com/java).
2. When you first plug it in (use the USB plug labeled USB not the HOST one), it complains and will discover a P771A device. When it does, right click on your computer, choose Manage my computer, go to the device manager and then right click on the P771A device. Click "Update Device Driver". Choose "Browse my computer for Driver software". Then choose, "Let me pick from a list of drivers on my computer". Browse to the \adt-bundle-windows-x86_64\sdk\extras\google\usb_driver folder which you would have if you had downloaded and installed the Google Android SDK. A list of 3 drivers will appear when you click OK. CHOOSE THE "ANDROID BOOTLOADER INTERFACE" as the driver. None of the others work.
3. Run the root script batch file mentioned above which can be found here at: sourceforge.net/projects/androidroot
4. The root script isn't really great at explaining so I'll try. When you first run it, make sure your device is unlocked and on the home screen.
5. The first thing it will do is reboot your machine. Don't press enter until your machine comes back up.
6. After your machine boots unlock it and then press Enter again. Your machine will reboot. This time it won't seem to come up but the backlight will remain on.
7. Wait about 30-45 seconds then press enter again. You should get: uid=0(root) gid=0(root) in the command prompt window.
8. Press Enter. You should get:
remount succeeded
727 KB/s (22364 bytes in 0.030s)
Removing changes except ROOT...
Installing superuser...
2288 KB/s (843503 bytes in 0.360s)
9. After about 30-60 seconds, your device should reboot. You'll see a box briefly saying "Android is Upgrading" and you'll arrive at the lock screen. Press Enter to exit the command prompt.
Your device is now rooted and you should see "SuperUser" installed. I promptly installed "root uninstaller" to get rid of Facebook, Skype, and Youtube which my little kids don't need access to. This device doesn't have a bootloader or recovery mode so rooting it doesn't get you much besides the ability to uninstall the system software. Have fun.
This may help someone but on step 2 of the guide on the second page, after you right click your device and go to "Let me pick from a list of drivers on my computer". You then click "Show All Devices" then "Have Disk..." Direct it to the root of the adt-bundle folder you downloaded then you can select from the three drivers. I'm on windows 7 32bit and the drivers didn't show up for me like how it was suppose to..
I also could NOT get any of the drivers in the "manufacturer USB" packet to install... I WAS able to install the google drivers, but that also would not allow ADB to see the device... So still stuck with everyone else...
P771A possible problem
I'm having a similar problem where the USB driver downloaded through Android SDK's -> Extras -> Google USB Driver, tells me that the file contains no information about my device. I noticed in the Sources of SDK, there wasn't an API for 4.0.4, only 4.0.3 then 4.1, so i downloaded 4.0.3 repo.
============================================
my devices is on 4.0.4, and my Kernal is as follows:
3.0.8+
[email protected] #8
Wed Aug 29 09:59:19 PDT 2012
Build Number:
P771A-user 4.0.4 IMM76D user.v402.007 release-keys
============================================
I've also made sure weather Unknown Sources is on, as well as USB debugging.
Might the Kernal be the problem? Also, does it matter weather its MTP or CTP?
Now HKC is telling me that they don't support the ability to jail break their devices
Sent from my P771A using xda app-developers app
hello,
I previously was using HTC explorer and had many great experience of rooting and changing custom ROMs setting up of adb was easy with it but currently I own a dell venue 7 3740 LTE tablet which is having KitKat 4.4.4 I have a HP laptop with windows 7 ultimate I want to start using adb in command prompt so that I can do lagcat and capture ota updates link also I want to use adb so that some apps which needs root but can be used via some tweaks done in adb eg.helium,screen shot ultimate etc.
please help me how to setup adb in my laptop.
Have you tried installing the Intel Android USB Drivers?
xBIGREDDx said:
Have you tried installing the Intel Android USB Drivers?
Click to expand...
Click to collapse
That one works amazingly well fixed my fastboot driver on windows 10
social-design-concepts said:
That one works amazingly well fixed my fastboot driver on windows 10
Click to expand...
Click to collapse
But Its not working for me.
http://forum.xda-developers.com/general/xda-assist/dell-venue-7-3740-mtp-usb-debug-problem-t3173463
xBIGREDDx said:
Have you tried installing the Intel Android USB Drivers?
Click to expand...
Click to collapse
yes I have installed the v1.9.0 setup in device manager in laptop when I connect my tab with debugging enabled it shows in portable device my tab name,and other device mtp is shown with yellow exclamation.
mtp drivers for tab are not getting installed.
in cmd when I hit adb devices I don't get my tab details
Does it show like the pictures in my link ????
Dipyaman said:
Does it show like the pictures in my link ????
Click to expand...
Click to collapse
yes its shows yellow error in mtp but I am able to transfer files from laptop and tablet only thing is I can't use cmd and adb but after going thru your link I come to know that my adb was too old which is of my HTC explorer so I downloaded adb (platform.zip) from the thread given in your post and then for mtp I manually selected driver installed in my laptop I.e adb interface >Samsung adb and then I tried cmd in new platform.zip which had updated adb files for jellybean+ version and now its working fine.
Dunno how you did that. I'm a newbie.
Could you plz help me out ?
I don't have any sort of "Adb" connection in device manager (which you can see in my image), which was supposed to be there.
Can you give me a detailed explanation of what you did ????
Dipyaman said:
Dunno how you did that. I'm a newbie.
Could you plz help me out ?
I don't have any sort of "Adb" connection in device manager (which you can see in my image), which was supposed to be there.
Can you give me a detailed explanation of what you did ????
Click to expand...
Click to collapse
so you too also want adb to work for you right?
I can't say exactly what made it work for me cause I have s duos 2 also n so its drivers are also installed in my lappy.
but you do one thing
1.install Intel android driver from above post v1.9.0
2.enable debugging in tablet and connect and then goto device manager where you have mtp error,right click on mtp,update drivers select from folder will appear below that must be some option select from installed drivers goto that see Intel android driver after that you will be getting multiple option android adb interface, adb composite interface select any one preferably android adb interface and install.after that uncheck debugging and again check it and see if mtp error is gone from device manager.
3.download platform.zip from your given thread link unzip it and in that folder open cmd by holding shift and right click do open cmd here and check if all is OK by typing adb devices,if its OK it will list your device.
I'll give it a try, then i'll inform you. Till then, please stick to the post ! Thank you for the info BTW.
Dipyaman said:
I'll give it a try, then i'll inform you. Till then, please stick to the post ! Thank you for the info BTW.
Click to expand...
Click to collapse
today I tried changing from samsung adb driver with Intel adb driver and it worked
djmacpro said:
today I tried changing from samsung adb driver with Intel adb driver and it worked
Click to expand...
Click to collapse
The problem is, Installing Intel USB drivers does not do anything. Its does not show up in my device manager.
Dipyaman said:
The problem is, Installing Intel USB drivers does not do anything. Its does not show up in my device manager.
Click to expand...
Click to collapse
if still yellow error is shown on device manager right click on it update driver,then browse from folder or look for installed driver some where is must be there search something related to Intel or adb and select that else forget it cause what's the use of adb for us as there is no custom ROM or other things to do.
other way is download helium app on PC and tablet and in ptp mode you can get adb working