Hello All,
First, let me say how much I've enjoyed reading this Forum and how much I LOVED my TMobile Samsung Vibrant 3G. While it worked for a long time running Froyo 2.2 with a Bionix Next-Gen V2 ROM, it was fantastic, but lately the microphone had been dying (I sounded more and more muffled no matter what I did). So I flashed up to ICS and installed Chimera to see if that might help. While the phone ran beautifully except for several apps that were rather wonky, I was getting more and more muffled.
So the other day I decided to restore my Nandroid backup, however when I flashed back I got stuck on the Vibrant boot screen. No matter what I do, I can't seem to get to Recovery.
How do I get back to Recovery from this? I have never used Odin, the only time I've ever hooked the phone up to the computer was when I originally flashed from Eclair to Froyo many moons ago. So please let me know if I'm missing something.
Any assistance would be greatly appreciated!
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
samsgun357 short and sweet as always
samsgun357 said:
You made a mistake when you tried to restore a 2.2 based backup from ICS base ROM. Now you must Odin to stock, its not that hard. First you will need to download the Odin program. I'm assuming you have device drivers on your PC but double check. Next you need 2 files, the 512 pit and jfd firmware file. Once you have those files you need to get in download mode.
I will link a thread with files and directions. http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Click to expand...
Click to collapse
OK I installed Odin and the necessary files and drivers, I plugged in the phone, but when I try to turn it on into Download Mode the Vibrant doesn't respond. There's just the little spinning light in the center of the screen. Odin doesn't recognize the phone either.
Anything else I can do?
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
samsgun357 said:
Odin won't recognize unless you are in DL mode. I linked a video, I know it says captivate. Don't worry about the mod etc just follow it to get in download mode.
https://www.youtube.com/watch?v=qXMqLpnTPh0&feature=youtube_gdata_player
I approve this message.
If this won't play just search download mode vibrant on YouTube.
Click to expand...
Click to collapse
OK watched the video, but 2 things:
-when I try to boot into Recovery it gets stuck on the Vibrant Samsung initial splash screen and never moves, even when holding down the 3 buttons;
-this video assumes I can access the phone to install the fix or anything else. I can't, it just stays stuck in the splash screen;
-I tried holding down the 3 buttons and simultaneously plugging in the USB cable, and still nothing but the splash screen;
-is there any way to turn on the device while hooked into the computer so Odin or something else can use the necessary files to turn it on and make it accessible?
Thanks all for your patience and advice, it's much appreciated. I LOVE this little phone and really want to heal her!
Hi,
I think you have tried to go to recovery mode using 3 button combo. But in order to use ODIN device has to be in DOWNLOAD MODE which can be done using following steps
1)start off with phone turned off
2)press down volume up, and volume down at same time, and never let go until you get into download mode. DON'T touch the power button
3) while holding down both volume buttons get your usb cable which is connected to your computer
4)plug in the usb cable into your phone, while you still hold down both up/down volume buttons at same time. Don't touch the power button.
5)As soon as you plug your usb cable into your phone, the phone will instantly go into Download mode.
6)You may now release the volume buttons
Click to expand...
Click to collapse
hope this will help you to go on
tc
NOTE: here is a link I found. Just take a look http://www.ithinkdiff.com/how-to-access-download-and-recovery-mode-in-samsung-vibrant/
OK we are trying to get download mode not recovery. Your phone must be off for download mode. If it flashes vibrant screen you have gone to far and something is wrong. I specifically said pay no attention to the mod in video. Regardless I think you might need a jig to get in download mode.
I approve this message.
OK, noob error (smacks head), I kept saying Recovery Mode when what I needed was DL Mode, my sincerest apologies.
I got into DL Mode finally by holding down the Volume buttons (not the Power button), then plugging in the USB cable. The Vibrant promptly went into DL mode. Odin recognized the phone and off we went. It's now back to Stock Eclair (yuck).
So next question: am I rooted or do I have to do that all over again? And if so, what's the fastest way to do it so I can flash to the ROMs I knew and loved?
Lastly, a great big THANK YOU to samsgun357 & haarsh for all your assistance, you guys ROCK! :good:
No you are not rooted after using Odin to go back to stock. Glad you got it buddy! Now use this guide to get root and cwm recovery. Option b is probably what you want
http://forum.xda-developers.com/showthread.php?p=9375927
I approve this message.
Glad you are successfully ODINed and you are in perfect position to make things BETTER
Still the device is not rooted as samsgun357 said. but no worries it is a simple process to get rooted and go ahead. I will post an video and hope it will also ease up your task
tc and its a pleasure to help you
Happy Flashing :good:
Yep, got it rooted and flashed Cyanogen7, then flashed up to an ICS ROM (started with Chimera but it's a tad wonky so flashed over to Euphoria, we'll see how that goes).
That said, the microphone is still sounding very muffled, so I think it's a hardware issue. I was due for an upgrade anyway so I picked up the Samsung 4G Blaze (nice since the Vibrant I had was the 3G). So right now I'm just having fun exploring Android on the Vibrant while I read up on how to root and improve the Blaze.
I will miss this little phone though, it was light and super fast and agile, perfectly sized, especially compared to the mini-tablets coming out lately like the Samsung SIII and LG L9 or HTC One. I prefer smaller phones, so the Blaze fits the bill right now even though it's heavier than my old Vibrant.
Thanks again for everyone's assistance, VERY much appreciated! :good:
Hey guys,
I'm having the same problem w/ my phone (see img).
I can't get out of the little loading pinwheel.
I've tried all the prescribed methods in this thread.
Thoughts?
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
check this thread : http://forum.xda-developers.com/showthread.php?t=848737
Gingerbread Bootloaders
Key Maps
For Recovery - Lower Volume Key + Power Button
For Download - Upper Volume Key + Power Button
Froyo Bootloader
Key Maps
For Recovery - Both Volume Keys + Power Button
For Download - Both Volume Keys and Connect USB Cable
Click to expand...
Click to collapse
tc
hoss9009 said:
Sorry, also, I can't get to DL or the splash page. When I turn the phone on, it goes directly to the spinning pinwheel.
Click to expand...
Click to collapse
Download mode IS what you need to use Odin a get back to stock.
The above post shows the button combo for DL mode and recovery based on which bootloaders you're running (thanks haarsh). If you haven't flashed GB boots, you have froyo boots.
Now make sure you have the correct Odin files and drivers on your PC.
The goal here is to get power to the phone, while holding button combo, from the PC.
Do a battery pull/replace. Plug USB into computer
While holding your button combo (see above) plug the phone in.
Hopefully you see DL mode
Also try pulling battery, plug USB in PC and phone
While holding button combo, pop the battery back in.
This can be tricky sometimes so don't give up.
OK. Let me backup and give you more info.
So sorry...
I rooted, but was unable to download ROM manager from the Store (im assuming bc it was running Froyo).
I was able to get CMW to install via update.zip. Once installed the phone was going directly into recovery when asked (3 button method). It would go into the Anroid recovery, first and then from continually installing CMW, go into CMW.
From there i installed a CM10 nightly.
Install went fine, but no mobile data connection. I went back to CMW and restored the original ROM, rebooted and am stuck w/ the pinwheel.
I can't get into to download mode AT ALL. I've tried the various button methods with no luck.
From what I did, I can assume that 2.1 IS installed on the phone.
Thoughts?
Thank you so much for the help.
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
samsgun357 said:
Well the issue you have was caused by going back to a 2.1 or 2.2 build from cm10 through cwm. You should have used Odin to get back to stock.
If you can't get in DL mode manually you will need to buy a DL jig. You can get them from www.mobiletechvideos.com also from amazon I think. You can also make one yourself, just search USB download jig, you should find it.
Sent from my SGH-T959 using xda premium
Click to expand...
Click to collapse
Ok.. nothing at against your advice, but do they really work?
Yes they do. Look them up, I'm sure there are testimonials.
Sent from my SGH-T959 using xda premium
Related
Hello everyone. I have a question about the current state of my Vibrant. Coming from a G1, I just upgraded to the Vibrant and have been loving since. I rooted my device, installed Clockwork Recovery, and flashed a new Rom. I decided to switch back to the stock rom but now when I turn on my Vibrant, it just sits at the Vibrant Samsung boot screen... Here are the steps I did up until this point:
1. Starting from the Stock T-Mobile rom, I applied Root update zip but booting into Recovery Mode (Holding down the volume Up/Down buttons and then pressing the Power button).
2. Installed Clockwork Recovery, and then did a Nandroid Backup.
3. Using Clockwork, I installed Eugene's Vibrant7 rom (I left create ROM Backup and Wipe Data options checked)
4. Vibrant7 rom flashed successfully but decided to switch back. So I used Clockwork to boot into manual recovery mode, selected Nandroid and then Restore
After it finished the Restore, it now sits at the Vibrant Samsung boot screen everytime I power it up... I'm thinking I should have not have used the Nandroid Restore to revert back to the stock ROM (unless I'm totally mistaken, I never used Clockwork Recovery before and have flash roms before with my G1).
At this point, could I just reflash back to the stock firmwire using ODIN (Directions from this thread [ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working) in the Vibrant/Android Development section). Would that take care of my problem or is my phone currently 'bricked' or SOL?
Thanks in advance for any help or clarification
yeah just odin back to stock... Read the directions carefully
this exact same thing is happening to me. I have tried to follow the instructions to odin. but when I hold volume down and power it just keeps rebooting to the vibrant page. but if I hold volume up and down and power I can get into recovery but non of the options fix my problem. Am I screwed or am I doing something wrong.
i'm having the same problem...stuck on boot screen
i'm on the bell network, are there instructions on how to use odin to fix my phone?
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
flashed a sgh t959 with a galaxy s i9ooo kernel oops
hi im stuck in manual mode and when i try to boot the screen shows two different galaxys s screens then goes back to manual mode and i cant get into down load mode it just goes back two manual mode was trying to root used wrong file i think im screwed i flash with oden and used i9000xxxhph tar file
Same with me, I think I soft bricked my vibrant, so I tried to restore to stock rom using odin. Odin detects it and runs stock rom just fine, but once it was restarting, the phone would not still boot up and would stay stuck at the vibrant samsung screen. I tried other roms such as froyo no brick, and i9000 stock rom also, would not boot also, just stuck at the samsung screen. What do I do? Odin works through the process fine though......why isnt it fixed?
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
yes yes yes! your mistake was using the power button! Lol.
FUTURE NOTE: if you upgrade to any gingerbread roms.... new bootloaders are required. If your JIG didnt get you into download mode before...... then it isn't working right. Once your into the the new Bootloaders for gingerbread, the sequence is........ HOLD VOL UP and POWER until you trigger DL mode. No USB required.... DO NOT FLASH NEW BOOTLOADERS WITHOUT A WORKING JIG IN YOUR POSSESION. TEST IT BEFORE YOU FLASH. I had...... an experiance.... lol
Not working
ParaMount33 said:
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
Click to expand...
Click to collapse
I tried all the instruction still stuck on Vibrant logo if i connect cable the Loader pix cums but doesnt load or show me battery image what to do now? also Odin doesnt recognize neither i can go to download mode!!!!!
If you can get in DL mode you are halfway there, next make sure you have correct drivers. Uninstall current drivers and reinstall correct drivers. Odin can be funny sometimes, you might need a new USB cable, try every USB port as well.
You can also use the All In One (AIO) program to get drivers and back to stock. If you are having issues with Odin try this
http://forum.xda-developers.com/showthread.php?p=11358713
sent from the depths of helly bean
hi,
Once i gt a prob restoring. But then I re-flashed the ROM which the nandroid backup was taken and then in CWM selected advance and gave restore data option(as i remember).. (it was not full restore with system..b/c I flashed system separately)
You can go back to stock using ODIN .. as mentioned by Daddy_617 previously.
tc
Also if Odin doesn't work for you try Heimdall. I've seen post where this has worked for others.
Vibrant stuck on "Vibrant Samsung"
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
I tried this but the say thing keeps happening ... really need help
After flashing Macnut R12 and Eugene's a13 kernel, my Vibrant will only boot to the "Galaxy S I9000" screen, but nothing further. The screen doesn't go black and no buttons flash, the phone just doesn't boot past that screen. I can enter recovery and download mode, and can use clockwork mod recovery, but I'm not sure what my next steps should be. Should I attempt to use Odin (Bricked my first Vibrant with that, though that one was HW-Locked), or is there some other way to fix this?
Scratch that, now my Vibrant boot-loops (Boots to galaxy S I9000 screen then restarts), and I can't enter recovery. Starting to freak out a bit, hoping download mode works... Any help would be appreciated.
Generic112 said:
Scratch that, now my Vibrant boot-loops (Boots to galaxy S I9000 screen then restarts), and I can't enter recovery. Starting to freak out a bit, hoping download mode works... Any help would be appreciated.
Click to expand...
Click to collapse
Gmail me [email protected]
Sent from my SGH-T959 using XDA App
Here is a couple of methods to get into download mode. Once you get to download mode, follow the directions later in my post...
First Method
1) Pull the battery, sim card, and sd card.
2) Reinsert battery but do not press any buttons.
3) Plug into usb that is connected to your computer. If something shows up on the screen (charging logo) then you should be golden.
4) Hold the vol up, vol down, and power until the screen comes on, immediately release the power button but not the other two. You should be in dl mode.
Second Method
1) Another method that seems to work for some people is to pull the battery, sim, sd card.
2) Reinsert battery and hold both volume buttons but do not press power button.
3) Then plug in usb. The phone should boot into download.
Third Method
1) You will need the samsung ADB drivers installed for your phone and ADB.
Samsung Drivers for 32 bit Windows: http://files.androidspin.com/downlo...=SAMSUNG_USB_Driver_for_Mobile_Phones_x86.exe
Samsung Drivers for 64 bit Windows: http://files.androidspin.com/downlo...ung/vibrant/&file=usb_drivers_GalaxyS_x64.zip
2) Remove sim card and sd-card. Remove the battery.
3) Hold buttons vol up, vol down, and power.
4) While holding down those 3 buttons put the battery back in and keep holding all 3 buttons until the vibrant disappears and reappears. Once it reappears, release all 3 buttons.
5) Now connect your phone to your pc via USB cable.
6) Open a cmd prompt and navigate to the folder with ADB and type "ADB REBOOT DOWNLOAD" caps are not necessary.
7) Your phone will reboot into the download mode.
Once in download mode
Download the files in the linked thread and follow the directions there or the ones below.
Odin and Files Needed Available Here: http://forum.xda-developers.com/showthread.php?t=734475
1) Open Odin and verify that one of the Com ports shows a device connected. If it doesn't try using a different usb port.
2) Load the .pit and pda files. It should be pretty obvious how to do that once you are in Odin.
3) Make sure that the option to partition is unchecked. The other two options should be checked.
4) Hit start and wait.
5) Your phone will restart when Odin is done and you will be good to go.
Also, you might have to build the usb jig. It is guaranteed to get you into download mode. Here is a link to that thread:
http://forum.xda-developers.com/showthread.php?t=819551
Also, if you would like I can use remote log in to your computer and do it for you. Send me a pm or email: [email protected]
Ok, Download mode (Via Volume + and - and plugging in usb) works flawlessly, but I'm still unsure of how to go about using Odin to fix this problem. Should I go the "Froyo that doesn't brick" downgrading route, or should I just flash JFD? And to the above poster, I won't have access to the internet for a couple hours after this post, so I can't email you right away. If I can't fix the problem later today, I will certainly contact you for some assistance.
Thanks for the guide, I'm just worried about what to flash. I've seen people praise Eugene's downgrading method for fixing most any problem (Froyo that doesn't brick to JFD), but I'm very much an Odin novice, and I'd hate to let it tear the life out of yet another phone (Though thankfully this one isn't HW-Locked). Also, does flashing JFD through Odin touch the SBL or anything that could affect my phone's ability to access recovery/download mode through hardware methods? I've heard that the JI6 OTA update fixes the 3-Button mode, but I'm unsure of whether or not JFD breaks that (Though I assume it doesn't). Anyway, thanks for the help, sorry if I don't post back soon, have to leave the house for a few hours, and I'm stuck with my old phone until I can fix my Vibrant.
One last question, should I use the Odin in the link, or an updated version (If one exists, I believe Odin3 1.70 is the latest and I don't know used in that thread)? Last time I used Odin it froze and killed my HW-Locked Vibrant.
Generic112 said:
Thanks for the guide, I'm just worried about what to flash. I've seen people praise Eugene's downgrading method for fixing most any problem (Froyo that doesn't brick to JFD), but I'm very much an Odin novice, and I'd hate to let it tear the life out of yet another phone (Though thankfully this one isn't HW-Locked). Also, does flashing JFD through Odin touch the SBL or anything that could affect my phone's ability to access recovery/download mode through hardware methods? I've heard that the JI6 OTA update fixes the 3-Button mode, but I'm unsure of whether or not JFD breaks that (Though I assume it doesn't). Anyway, thanks for the help, sorry if I don't post back soon, have to leave the house for a few hours, and I'm stuck with my old phone until I can fix my Vibrant.
One last question, should I use the Odin in the link, or an updated version (If one exists, I believe Odin3 1.70 is the latest and I don't know used in that thread)? Last time I used Odin it froze and killed my HW-Locked Vibrant.
Click to expand...
Click to collapse
Thank you for pointing out that the linked thread has the old Odin. I attached the new Odin 1.7 in this post. The other files (pit and pda) in that thread will work fine. Once you get booted into that ROM (Stock JFD) just re-root, install CWM recovery and reflash with a ROM of your choice.
Just wanted to say that Odin ran successfully for me, and I now have my Vibrant back in working order. Thanks for the help (and that nifty little guide).
Generic112 said:
Just wanted to say that Odin ran successfully for me, and I now have my Vibrant back in working order. Thanks for the help (and that nifty little guide).
Click to expand...
Click to collapse
You are welcome. Glad you got it working again...
hey guys i'm having serious trouble with this miui 2.3.7. I flashed the rom, and everything was (kind of, the rom was buggy, but working) so i wanted to flash another one after a couple weeks so when i did, it gave me an error while flashing, then i tried to reboot, and i was on a boot loop with the vibrant and platypus screen. I tried reflashing the miui rom now (at the advice of someone else) and now My phone is just stuck on the vibrant screen and i can't even get into recovery. Please help if anyone can.
vballrkc said:
hey guys i'm having serious trouble with this miui 2.3.7. I flashed the rom, and everything was (kind of, the rom was buggy, but working) so i wanted to flash another one after a couple weeks so when i did, it gave me an error while flashing, then i tried to reboot, and i was on a boot loop with the vibrant and platypus screen. I tried reflashing the miui rom now (at the advice of someone else) and now My phone is just stuck on the vibrant screen and i can't even get into recovery. Please help if anyone can.
Click to expand...
Click to collapse
Try holding only the bottom button and power to get into recovery.
You might have to odin to stock. This is an one click too.
http://forum.xda-developers.com/showthread.php?t=954509
To get into download mode unplug your phone, take out your battery. Put the cable into your computer, hold the vol - and +, plug into your phone then insert the battery. (Put battery case on too so it does not fall out.)
It will revert you back to factory. Root it using it as well (using the tool), and then download miui from rom manager.
Let me know if you need anymore help.
I made this MIUI install guide for my GF at the time it's broken down in the simplest terms humanly possible so if the guide sounds like it's mocking you, well it's not it's just designed for people who have no idea what there doing, aka My ex lol follow it to A T starting with Odining to stock. Links to all files needed are embedded in the document itself.
https://docs.google.com/document/d/14xGkh3BuU1OYR6eYY0XAk6BoRHsQAPWEHeVSJ1HcioI/edit
Note about odin it's reasonably self explanitory
open the program check ONLY these boxes
Repartition
Auto-Reboot
Reset Time
Select the "pit" button choose
512.pit
select the "PDA" button Choose
T959UVJFD.tar
turn phone off
press and hold Vol+ and Vol- now plug in usb that should enter you into Download mode and odin should find the device press start and wait for the phone to finish the process
now follow the guide on installing MIUI.
boystuff said:
I made this MIUI install guide for my GF at the time it's broken down in the simplest terms humanly possible so if the guide sounds like it's mocking you, well it's not it's just designed for people who have no idea what there doing, aka My ex lol follow it to A T starting with Odining to stock. Links to all files needed are embedded in the document itself.
https://docs.google.com/document/d/14xGkh3BuU1OYR6eYY0XAk6BoRHsQAPWEHeVSJ1HcioI/edit
Note about odin it's reasonably self explanitory
open the program check ONLY these boxes
Repartition
Auto-Reboot
Reset Time
Select the "pit" button choose
512.pit
select the "PDA" button Choose
T959UVJFD.tar
turn phone off
press and hold Vol+ and Vol- now plug in usb that should enter you into Download mode and odin should find the device press start and wait for the phone to finish the process
now follow the guide on installing MIUI.
Click to expand...
Click to collapse
Odin out of it as said above, you need to get your partitions right. If you come back flash straight from a 2.2 rom like (bionix)
yeah i would love to do that but unfortunately when i go open oden and go into download mode the computer can't recognize my phone due to the drivers being changed to the nexus 1 drivers (that's what i've gathered from doing research). And I can't find anywhere to download the nexus 1 drivers....
vballrkc said:
yeah i would love to do that but unfortunately when i go open oden and go into download mode the computer can't recognize my phone due to the drivers being changed to the nexus 1 drivers (that's what i've gathered from doing research). And I can't find anywhere to download the nexus 1 drivers....
Click to expand...
Click to collapse
These should work for you.
http://code.google.com/p/android-roms/downloads/detail?name=android_usb_windows.zip&can=2&q
ok as of now, all i can do is get into download mode or get to the samsung screen, can't get into cwm. when i get into download mode, the computer won't recognize the phone due to the driver issue, i tried installing the drivers that the above poster suggested and they won't install when i go to device manager. any thoughts?
Install Samsung Kies (To get Drivers).Then, try my guide (link in signature).
Sent from my SGH-T959 (Samsung Vibrant)
ok downloading now....will keep you posted on progress
ok great news, the samsung kies worked and now i'm back to stock, but now i can't get into recovery....I'm assuming i'm still rooted? am i?
Now that you are back on stock you are no longer rooted. Now follow my guide on flashing MIUI. It has everything you need from flashing instructions to all compatible custom kernels for MIUI.
Sent from my SGH-T959 (Samsung Vibrant)
yeah sorry, i had a bone head moment. i re rooted the phone and now i'm good. thanks to everyone for all their help!!
My SGH-i777 is running the latest ported ROM based on the CM9 March 23rd nightly. I've made a terrible mistake. I was renaming my last backup via ROM Manager, and decided I might as well do another one since my set up was where I wanted it. Like an idiot, I did it via RM, even though I've read there's a bug. Well, needless to say my phone won't boot past the Samsung yellow triangle boot screen.
I've been searching for the best method to fixing the issue, but can't find a solid answer. I'm able to get into download mode, I'm just not sure the safest route from here...
I originally rooted via heimdall on a Mac, but also have a PC - which I'm actually currently downloading ODIN on there.
Can anyone point me in the right direction?
If you can get into download mode use the full version of Odin to flash a kernel with cwm and uncheck auto reboot. Then you should be able to hold both volume keys with power to get into recovery. Then you can reflash cm9
You really have to make sure to uncheck auto reboot though cause any non ics kernel booting ics won't be good.
EDIT: to avoid this, are you able to get into cwm by holding both volume keys + power?
Sent from my SGH-I777 using xda premium
h0ckey10 said:
If you can get into download mode use the full version of Odin to flash a kernel with cwm and uncheck auto reboot. Then you should be able to hold both volume keys with power to get into recovery. Then you can reflash cm9
You really have to make sure to uncheck auto reboot though cause any non ics kernel booting ics won't be good.
EDIT: to avoid this, are you able to get into cwm by holding both volume keys + power?
Sent from my SGH-I777 using xda premium
Click to expand...
Click to collapse
Thanks for the quick reply. OK, I'll try as soon as I get ODIN on my PC. No, I'm not able to get into CWM. Holding both volume keys + power just results in the Samsung boot screen.
I was able to use ODIN to flash a kernel with CMW, and got a PASS! - and I didn't check off Auto Reboot...
My phone is still showing the download mode screen, though, a progress bar is now visible.
From here, should I:
pull the battery
unplug USB
place the battery back in
volume up + down + power to CWM
reflash CM9
I thought I replied, but looks like it didn't go through.
Anyway, thanks again. I did pretty much exactly what you said, and I'm back on a fresh CM9 build, everything working.
So lesson learned...uninstall ROM Manager so I don't make a careless mistake like that again.
Same
enjoirock said:
My SGH-i777 is running the latest ported ROM based on the CM9 March 23rd nightly. I've made a terrible mistake. I was renaming my last backup via ROM Manager, and decided I might as well do another one since my set up was where I wanted it. Like an idiot, I did it via RM, even though I've read there's a bug. Well, needless to say my phone won't boot past the Samsung yellow triangle boot screen.
I've been searching for the best method to fixing the issue, but can't find a solid answer. I'm able to get into download mode, I'm just not sure the safest route from here...
I originally rooted via heimdall on a Mac, but also have a PC - which I'm actually currently downloading ODIN on there.
Can anyone point me in the right direction?
Click to expand...
Click to collapse
It seems I may have done the same thing...I'm stuck on Samsung with yellow triangle after downloading CM9 and launching RomManager. Odin won't recognize the phone. Would you mind posting a step-by-step for a simple minded man?
Thanks so much.
sullystix said:
It seems I may have done the same thing...I'm stuck on Samsung with yellow triangle after downloading CM9 and launching RomManager. Odin won't recognize the phone. Would you mind posting a step-by-step for a simple minded man?
Thanks so much.
Click to expand...
Click to collapse
Can you get into download mode, like I could? Otherwise, I wouldn't know, sorry.
If you can, this is what I did (it worked for me, hopefully for you too, but you might want to search/read more before you dive in, just in case your problem isn't the same as mine):
power phone down
download a kernel with CWM to PC
if you never have, download/install drivers/Kies to PC
plug USB cable into phone/PC (phone still off)
hold vol down + power on phone to enter download mode
launch Odin on PC
uncheck reboot in Odin (important!)
add the kernel
run Odin
once you see PASS! in Odin, and the progress bar full/complete on your phone you're on the home stretch
while still plugged in, pull the phone battery
unplug USB from phone
battery back in
hold vol up + vol down + power to enter CWM
re-flash CM9
reboot
Good luck! Let me know how you make out.
Thanks
Turns out the only way I could get into download mode was pulling the battery, connecting to PC, holding power and volume and reconnecting to PC. Went right into download mode and I'm able to fix from there. Thanks so much! Didn't know that one! Appreciate all your help!
I flashed Doc’s ICS v 12 coming from Bionix V (2.2 based). Didn’t really like the rom..wanted to go back so I tried to restore Bionix V from recovery…. The phone was taking really long to restore so I restarted it from recovery. Ever since then, It has been stuck on Samsung Vibrant black screen. The three button combo isn’t taking it to recovery either. Seems like I bricked my phone… Is there anything that can be done to get it to a working state?
Thanks a lot
Oh hey I bricked my phone the other day!
Alright with the research I did, there's a few things to try.
One, take your battery out. Plug in your phone WHILE holding both volume keys and plug in the battery. See if anything comes up.
Two, or try this. This is what unbricked my phone. My phone wasn't responding to attempting to get into download mode. This saved me.
One-Click Unbrick
I read that it's different for everybody, so take this with a grain of salt since I'm sure you've already been successful at it before, but you should only have to hold the Volume Up button to get to the Download mode if you're using the GB bootloader. Take out your battery to ensure the phone is off, put the battery back in, hold the Vol+ button only (no power, or combos), and then connect your phone to the USB cable plugged into your computer. That's all I've ever had to do to get to Download Mode, but like I said mileage seems to vary (by bootloader, I think).
If either that or knoka's suggestion works and you get your phone back, you should always use odin (or heimdall) to get back to back to a pre-ICS state. Using a nandroid/CWR recovery/backup to do it is bad mojo (as you're well aware now), and should only really be used when you're messing around with ROMs of the same flavor (Froyo, GB, ICS).
So I was able to bring the phone to download mode.. I took out sd card and sim card, pressed the volume up key only and plug it into usb port.
My computer isn't recognizing the phone... how can I unbrick it from here on. Do I use odin? Are there any other simpler methods? If no I will use odin ...can anyone direct me to links...I found a bunch but not sure which one i should go with?
First, you cannot restore a 2.2 coming from any GB or ICS ROM. You need to Odin back to 2.1 and then go back to 2.2. Once you flashed ICS you repartitioned the /system from RFS to MTD. This can only be reversed by Odin or Heimdall.
That you can get into DL mode is good. You can uninstall your drivers on your PC, download the toolbox from my signature and reinstall the drivers that way. It also has the pit/tar files and Odin v1.8 included as well. Look at the AIO Toolbox's OP in the Dec section for instructions.
Thanks for the advice. I am downloading your toolbox.
Is there a way I can just flash the same ICS rom I did before. I want to get my phone in working condition for this week if I can as I am busy with a class and have to study for it.... if not then I will suck it up and odin back to 2.1 tonight
another question: after installing aio toolbox. I clicked on flash to stock: checked if the USB debugging is enabled...it said its disabled. How do I enable it when my phone can only be in download mode. thanks
sLiKK said:
Thanks for the advice. I am downloading your toolbox.
Is there a way I can just flash the same ICS rom I did before. I want to get my phone in working condition for this week if I can as I am busy with a class and have to study for it.... if not then I will suck it up and odin back to 2.1 tonight
Click to expand...
Click to collapse
At this point it would be better to get it back to 2.1 and then flash something from there. If you need something that works right out of the box, try Moped_Ryder's ROMs. They are 2.2's but if you need something to work completely while you are studying, I would suggest those for now. Then once things calm down for you, then flash an ICS.
sLiKK said:
another question: after installing aio toolbox. I clicked on flash to stock: checked if the USB debugging is enabled...it said its disabled. How do I enable it when my phone can only be in download mode. thanks
Click to expand...
Click to collapse
You don't need to have debugging enabled to use Odin. Just make sure the yellow COM button is lit up and you are good to go. Debugging is for Mass Storage Mode, not Download Mode.
awesome...Im back to stock vibrant. I mounted the sd card and the previous app folders are still there. How do I reset/factory wipe to get rid of all that junk. AIO toolbox says to unplug, replug and then click on master clear button on odin..however i am unable to find that button...there is a 'reset' button.... is that the one i need to click?
Thanks.
I would just do that manually on your PC. Just pull off everything and put it on your PC. That way you will still have a copy of anything that you might need. Masterclear will wipe everything and once it is gone, there is no return.
When you are ready to flash a ROM, just pull the CWR from my signature and put it on your internal. Make sure it is the only thing labeled Update.zip and then boot into recovery, scroll down to reinstall packages. It will cycle through and you might have to hit it again. Once it is done, your recovery will go from stock (blue) to CWR (green), then you can flash away.
If you are going to flash an ICS ROM, see my guide, also in my signature. It will help.
^ Thanks so much for your help and advice. My phone is back to normal ..I was able to flash Bionix V 1.3.1 rom and everything is fine...I wouldnt have my phone in working condition..if it wasn't for your tool and this forum. Thanks.