Using this post from this thread: http://forum.xda-developers.com/showthread.php?t=1825272
as i9000 said:
RESCUE FIRMWARE SGSIII I9300
This firmware is made for emergency recovery device to factory condition
Firmware consists of four parts, plus pit
Attention! All user data will be deleted during flash the firmware
After flash you will have clean device (factory condition) CSC - KOR default
How to flash:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
DOWNLOAD FIRMWARE FACTORY I9300XXDLJ4
Click to expand...
Click to collapse
So I flash it on my phone using odin and it fails. Odin just goes red.
Odin log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXDLJ4_368423_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXDLID_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_BTU_I9300OXADLJ4_368423_MULTI_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008>
<ID:0/008> Re-Partition operation failed.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Why the hell are you using a pit file?
Sent from my Nexus 7 using xda premium
nodstuff said:
Why the hell are you using a pit file?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
Its what the instructions said to use. But my problem is that odin wont flash anything. Not even checkrom.
ninjasstolemytv said:
Its what the instructions said to use. But my problem is that odin wont flash anything. Not even checkrom.
Click to expand...
Click to collapse
uncheck re-partition in options and dont flash the pit file.. btw looking at the odin log you seem to have flashed everything other than the pit file so try powering on your phone cuz it looks like you successfully went back to stock and only the pit file installation failed
k786 said:
uncheck re-partition in options and dont flash the pit file.. btw looking at the odin log you seem to have flashed everything other than the pit file so try powering on your phone cuz it looks like you successfully went back to stock and only the pit file installation failed
Click to expand...
Click to collapse
When I flash it there's no progress bar on the phone, so I highly doubt that it flashed anything at all.
For a simple recover you don't have to re partition your device, many bricks are just corrupted files in system partition or kernel.
Just flash any Rom you want using Odin, without partitioning.
Striatum_bdr said:
For a simple recover you don't have to re partition your device, many bricks are just corrupted files in system partition or kernel.
Just flash any Rom you want using Odin, without partitioning.
Click to expand...
Click to collapse
I think the real problem is, the device wont let Odin flahs aything
Try this guide ...
No guarantees but I flashed 2 S3's back to ICS 4.04 yesterday after Jellybean update which screws things up with Allshare Cast ...
forum.vodafone.co.uk/t5/Samsung-Galaxy-S3/How-to-Flash-Rollback-Galaxy-S3/td-p/1273246?oo=0&askid=b6988f58-c28d-4fd8-b10f-8a01b5a19979-0-uk_gsb
Worth a try !
Related
Hi
I have searched the forum and various others but still could not solve my problem. SO please bare with me for 5 mins to read the following.
I have recently updated to Wanam's latest V5.3 XXELLA but over night it rebooted and stuck in a bootloop. so what i did was recovery wipe everything including dalvik cache BUT still stuck in bootloop. SO again i went back on the pc and flash the stock official XXELLA again bootloop again. I have found out some people might need to go into recovery and wipe everything after the official flash. BUT again still stuck in bootloop.
I honest don't remember ticking repartition but now when i try to flash ANYTHING it says the following:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXELLA_I9300OXAELLA_742798_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I have gone as far as finding PIT file from previous thread try to flash it but it just stucks at this forever:
I have tried the following 3 files from http://www.droidevelopers.com/f363/11722-[download]-ops-pit-files.html
GT-I9300_mx_20120220.zip
GT-I9300_mx_20120322.zip
GT-I9300_mx_20120329.zip
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
Please anyone if could shine a light on me on where to go. now when im in download mode this is what i see:
FACTORY MODE
PRODUCT NAME:
CUSTOMER BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
SO i have no model number and no boot and not flashable and this is all i will see when i power it up
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
STILL REVIVABLE?OR IS IT COMPLETELY DEAD?!
Believe this is another case of sudden death syndrome (eMMC failure)... you'll have to return it to a samsung service centre.
Sent from my GT-I9300 using Tapatalk 2
beaver2233 said:
Believe this is another case of sudden death syndrome (eMMC failure)... you'll have to return it to a samsung service centre.
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
is there nothing i can do apart from returning it to samsung? because the thing is i moved from uk to china and well if im being honest people here charge you for whatever they do. so you could say there is not such thing as warranty if you know what i mean. so i will want to fix it myself if possible.
if it is the sudden death syndrome, it is hardware failure, so no way to fix it yourself (not through software flashes etc) - someone else might need to confirm this, but seems to be the problem you're facing.
Sent from my GT-I9300 using Tapatalk 2
Custom rom + bootloop .
Its not dead looks like user or something has lost PIT partition .
As it stands it will fail warranty . Its not dead and download mode shows non stock firmware .
jje
so what do i need to do to revert it?
many thanks
hi! i would like to ask how's your phone? did you solve the problem of it? we have same situation i tried to flash different pit files but with no success. tried to flash official rom but it is still looking for pit file.
different pit files? flashing a wrong one kills the phone, there's nothing you can do.
I tried to flash my note 2 to 4.1.2 and it failed. Now I'm just trying to get it back to stock. It keeps failing on modem.bin.
I've tried...
I605_VRALJB_Restore.tar
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW-Rev0406_low_ship_user.tar
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar
root66_VZW_stock_system.tar
My OS is Windows 8 64 bit.
Odin message is as follows
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas?
If I remember right you should try a different version.
I tried using my work computer (also windows 8 64 bit) and finally got the root66_VZW_stock_system.tar file to flash, but then it gets stuck in a boot loop.
What version should I be trying?
Thanks
I can get the phone to boot using root66 (http://forum.xda-developers.com/showthread.php?t=2024207) or VRALJB_rootedstockdeo.zip (from beans - http://www.androidfilehost.com/?fid=9390225151984926781), but I get no signal. My IMEI is uknown. I've been able to generate a new IMEI file with sgs3.nv.gen, but nv-items_reader_writer won't push it to my phone (http://forum.xda-developers.com/showthread.php?t=1804123).
While playing around I noticed something odd with the phone in windows explorer (image below). My internal memory and external sdcard seem fine, but the internal sdcard seems hosed. I tried creating a folder and it threw up an error. I'm guessing my partitions are all borked, but I'm not sure how to get them back to normal. Once the phone is back to normal I'm sure I can get my IMEI back in there and everything working again.
I've tried Section 1a and Section 1b from the root66 link above with no luck. I've tried a few other pit files with no luck. They hang on Get mapping for PIT in odin.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
My phone suddenly stopped working and I only have access to download mode..
I tried to flash the stock firmware using odin but it failed. I removed kies from my computer and tried different sockets/cables/computer/firmware but it always fails. I guess its because the debugging mode is not enabled in my phone. how can I fix it?
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLSD_I9100OJVLS6_I9100XXLS8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> boot.bin
<ID:0/010> NAND Write Start!!
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Alright, tell me a story that includes:
Where were you when this happened (ROM).
Where did you try to go (ROM)
And this has got nothing to do with usb debugging, don't worry.
Sent from the little guy
gastonw said:
Alright, tell me a story that includes:
Where were you when this happened (ROM).
Where did you try to go (ROM)
And this has got nothing to do with usb debugging, don't worry.
Sent from the little guy
Click to expand...
Click to collapse
I had the official v4.1.2 (I9100XWLSD_I9100OJVLS6_XSG) and tried it and didnt work and i tried another one (I9100XWLSS_I9100OXXLS9_I9100XXMS2_DNF) + Siyah-s2-v6.0b4 + Siyah-s2-v6.0b5
I downloaded the first two through sammobile
I already know the CSC and PDA for my phone, I dont know if that could help
Flash JB leak (csc, pda and Phone only).
I9100 I assume, right?
Sent from the little guy
gastonw said:
Flash JB leak (csc, pda and Phone only).
I9100 I assume, right?
Sent from the little guy
Click to expand...
Click to collapse
I only used the pda field in odin
Yes its I9100
Yes, an md5 file.
Go get jb leak and let's get your phone to boot.
What ROM were you on when this happened?
Sent from the little guy
gastonw said:
Yes, an md5 file.
Go get jb leak and let's get your phone to boot.
What ROM were you on when this happened?
Sent from the little guy
Click to expand...
Click to collapse
which one shall I get?
I was on the official JB 4.1.2
http://forum.xda-developers.com/showthread.php?t=1995767
is this one fine?
http://www.sammobile.com/2012/11/15/i9100xxlsj-–-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/
I guess it's the same.
Sent from the little guy
gastonw said:
http://www.sammobile.com/2012/11/15/i9100xxlsj-–-galaxy-s-ii-android-4-1-2-jelly-bean-test-firmware/
I guess it's the same.
Sent from the little guy
Click to expand...
Click to collapse
ok i'm downloading now
PDA: I9100XWLSD
CSC: I9100OJVLS6
PDA: LSJ
Phone: LS6
CSC: CSC
Sent from the little guy
downloaded, now what?
24HR44 said:
downloaded, now what?
Click to expand...
Click to collapse
put the phone into 'Download' mode and flash the firmware dwnloded using 'ODIN'
Sun90 said:
put the phone into 'Download' mode and flash the firmware dwnloded using 'ODIN'
Click to expand...
Click to collapse
ok.. there are many files and I'm not sure which ones to use and where, can you help me with that?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and one last Q, am I gonna lose the data stored in the phone?
gastonw said:
PDA: LSJ
Phone: LS6
CSC: CSC
Sent from the little guy
Click to expand...
Click to collapse
CSC is LS1.
Just those 3 tar files, please double check before you flash.
You will lose your installed apps yes; your pics and s#!t, no.
Sent from the little guy
gastonw said:
CSC is LS1.
Just those 3 tar files, please double check before you flash.
You will lose your installed apps yes; your pics and s#!t, no.
Sent from the little guy
Click to expand...
Click to collapse
I double checked and tried it twice with the same result!
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> boot.bin
<ID:0/010> NAND Write Start!!
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Uninstall & reinstall kies.
Try another usb cable / usb port.
Sent from the little guy
gastonw said:
Uninstall & reinstall kies.
Try another usb cable / usb port.
Sent from the little guy
Click to expand...
Click to collapse
its uninstalled, I will try that now.. they said it shouldn't be working during this process thats why I uninstalled it!
I tried another port and cable but it didn't work
Install latest kies and kill all 4 applications running on background.
Sent from the little guy
I ran WLSS Stock Rom with Kernel for some time
Yesterday I updated Google Search, the phone froze -> rebooted
Sine then about 20 times the phone came up froze and shutdown
Without missing a beat I thought it was a wonderful opportunity to flash the new Stock WLSW
I kill all of the kies processes and and tried to flash and it always fails !
Tried Odin 3.04, 1.85 and even tried reverting to WLSS with the same result....
Help someone...........:crying:
Now I can ONLY go to Download mode, there is now recovery.
When I try to boot normally I get a screen the tell's me :
Firmware upgrade encountered
an issue, Please select
recovery mode in Kies & try again.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Odin Screen Shot :
Odin log :
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLSW_I9100XXMS2_I9100XEULS5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Stock Rom source :
http://forum.xda-developers.com/showthread.php?t=1544487
Philz kernel source:
http://forum.xda-developers.com/showthread.php?t=1877270
For the users who search with the same symptoms TRY THIS ! :
The Issue is resolved !
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasnt able to flash !
10Q you all !
That pic on the screen means it's already in download mode (forced download mode). You need to search for Hopper8's 'Odin won't work' thread. I'd be surprised if you can't successfully flash with the info/stuff to try in that thread.
MistahBungle said:
That pic on the screen means it's already in download mode (forced download mode). You need to search for Hopper8's 'Odin won't work' thread. I'd be surprised if you can't successfully flash with the info/stuff to try in that thread.
Click to expand...
Click to collapse
if you're referring to this : http://forum.xda-developers.com/showthread.php?t=2345831
I did everything there but PIT or a costume rom/kernel....
This is the next step?
So you did everything, including the flashing of the 3 part firmware? Assuming you have an I9100 anyway.
Don't flash a pit (I'd like to say ever) but at least not now.
You can try flashing Siyah v6 as linked in the guide. I'd continue to try to flash JB leak, the 3 part firmware.
Sent from a galaxy far, far away
Hopper8 said:
So you did everything, including the flashing of the 3 part firmware? Assuming you have an I9100 anyway.
Don't flash a pit (I'd like to say ever) but at least not now.
You can try flashing Siyah v6 as linked in the guide. I'd continue to try to flash JB leak, the 3 part firmware.
Sent from a galaxy far, far away
Click to expand...
Click to collapse
Isn't the 3 part firmware is with a PIT?, i didnt try this one,
And Siyah fails also......
Code:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> zImage
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
The 3 part firmware consist of : Firmware + CSC + Modem.The good is with the 3 part firmware is that it does a factory reset automatically.BTW,I've heard so many issues like this,that people on stock ROM were updating apps/browsing internet,then it suddenly froze and Odin never works.I recommend not to use Samsung firmware,or at least not 100% original.Use a custom stock ROM.and also,if siyah failed too,then I think your only options are: 3 part firmware, .PIT or nothing
GamingDj said:
The 3 part firmware consist of : Firmware + CSC + Modem.The good is with the 3 part firmware is that it does a factory reset automatically.BTW,I've heard so many issues like this,that people on stock ROM were updating apps/browsing internet,then it suddenly froze and Odin never works.I recommend not to use Samsung firmware,or at least not 100% original.Use a custom stock ROM.and also,if siyah failed too,then I think your only options are: 3 part firmware, .PIT or nothing
Click to expand...
Click to collapse
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasn't able to flash !
10Q you all !
Idan.lv said:
The issue was resolved after replacing the USB cable !
The USB Cable did charge and transfer data but for some reason with this particular cable i wasnt able to flush !
10Q you all !
Click to expand...
Click to collapse
to flush= clean toilet/wc
to flash= install firmware
As a grammar nazi I couldn't miss this one.
GamingDj said:
to flush= clean toilet/wc
to flash= install firmware
As a grammar nazi I couldn't miss this one.
Click to expand...
Click to collapse
what ever do you mean....?
thank you for the correction
Dyslexia + No a native speaker = comedy
can be deleted. resolved!
daign said:
So I am stuck in Odin Bootloop into the downloading screen. I am trying to refllash the stock firmware
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The message log from odin says:
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Added!!
Odin v.3 engine (ID:15)..
File analysis..
SetupConnection..
All threads completed. (succeed 0 / failed 1)
Removed!!
Added!!
Odin v.3 engine (ID:15)..
File analysis..
SetupConnection..
Initialzation..
Erase...
Set PIT file..
DO NOT TURN OFF TARGET!!
Get PIT for mapping..
Firmware update start..
sbl1.mbn
NAND Write Start!!
sbl2.mbn
sbl3.mbn
rpm.mbn
aboot.mbn
FAIL! (Auth)
I have tried rebooting the phone into recovery and it always goes into Odin. So I've got a bricked phone until I can figure this out.
Thanks for any advice you may be able to go give!
-D
Click to expand...
Click to collapse
You cant flash a custom recovery on me7. I would read a little bit next time I think this has been posted three times today. Youll have to flash the stock me7 image to get back the stock recovery. Everytime you try to boot to recovery youll get put in download mode. You can boot normally by using the button combo for download mode and then denying it.
You also dont flash a stock restore file under bootloader you flash it under pda.
Sent from my SCH-I545 using Tapatalk 2
hexitnow said:
You cant flash a custom recovery on me7. I would read a little bit next time I think this has been posted three times today. Youll have to flash the stock me7 image to get back the stock recovery. Everytime you try to boot to recovery youll get put in download mode. You can boot normally by using the button combo for download mode and then denying it.
You also dont flash a stock restore file under bootloader you flash it under pda.
Sent from my SCH-I545 using Tapatalk 2
Click to expand...
Click to collapse
Thanks. Got that resolved a while ago! :good: