Hi Everyone,
I flashed JB leaked firmware through ODIN and it failed, I had selected PDA, CSC, phone accordingly as i was doing it second time on my frnd's phone, but it failed saying write error.
Now I can't go into download mode but I can see a weird sign: phone-pc sync logo.
Odin is recognizing my phone and I tried to flash again but same thing happened.
Please help what should I do now, it's urgent guys please help me out.
I m getting this following error
:
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Download mode or recovory works ?. Then flash a stock ics Rom and try again.
Hope it works..
Sent from my GT-I9100 using xda premium
Unplug your phone from usb.
Close odin and open it again.
just hold down power button while press volume down and home button. it will reboot into download mode
plug in
set pda and etc accordingly. flash.
Whenever you fail, you must close odin and unplug to try again to be sure.
Also try changing usb port if one side fails. Make sure your pc recognize and install driver before you plug in
Mebin Robin said:
Download mode or recovory works ?. Then flash a stock ics Rom and try again.
Hope it works..
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
no download mode and no recovery mode is accessible.. all i can see is an exclamation mark between a pc and phone logo in black screen
Have you tried a usb jig to get you into download mode? If you don't have one look at the thread about jig's on your area.
Sent from my GT-I9100 using Tapatalk 2
mohitgalaxy3 said:
no download mode and no recovery mode is accessible.. all i can see is an exclamation mark between a pc and phone logo in black screen
Click to expand...
Click to collapse
Indeed you can't access download mode now. But JIG will solve your problems. I had this problem myself 1 year ago and made a JIG.When you connect it, the phone will enter in Download mode. Search here for a tutorial on home-made jig, it takes you less than 10 minutes to make.
Good luck!
mohitgalaxy3 said:
no download mode and no recovery mode is accessible.. all i can see is an exclamation mark between a pc and phone logo in black screen
Click to expand...
Click to collapse
So you cannot get into download mode ?
A JIG puts the phone into factory mode which is the same as odin and download mode.
I was forced to make a JIG several months ago.
Good luck.
Gillion said:
So you cannot get into download mode ?
A JIG puts the phone into factory mode which is the same as odin and download mode.
I was forced to make a JIG several months ago.
Good luck.
Click to expand...
Click to collapse
Guys I can get into download mode.....I mean odin is working but as soon as I am trying to flash any rom it failed.
I have also tried XWLPJ but it's also failed.please help.
mohitgalaxy3 said:
Guys I can get into download mode.....I mean odin is working but as soon as I am trying to flash any rom it failed.
I have also tried XWLPJ but it's also failed.please help.
Click to expand...
Click to collapse
flash the pit file without firmware, reboot, pull battery, go back download mode, flash the firmware.
ksilver89 said:
flash the pit file without firmware, reboot, pull battery, go back download mode, flash the firmware.
Click to expand...
Click to collapse
no don't do this. You will **** up the phone. If you put the pit, put the firmware also.
Related
I just got my phone yesterday and rooted it. Installed CWM and OCLF. Everything went fine.
Then today I:
-Disabled the lagfix, flashed the Fascinate lockscreen through CWM.
-Enabled the lagfix.
-Saw that the lockscreen took away my battery mod
-Disabling OCLF takes forever so I ask the forum if its okay to flash stuff other than roms without disabling OCLF
-Was told the lagfix is only to be disabled if flashing full ROMs
-Tried flashing battery mod in CWM without disabling lagfix first
-Phone ended up in endless boot up so I go into recovery mode and deleted user data
-Phone still endless boots so I look up ways to unbrick/flash stock JFD
-Downloaded Odin and put phone into download mode
-Phone is stuck at "Downloading... Do not turn off target!!!" screen, and does not mount to computer through USB
Aaaaand this is how I'm sitting as of now. What do I do? Did I really just break my one day old phone?
Make sure that you install the drivers or odin won't do you any good. Once you have the proper drivers installed, odin will display a com# in red. From there just go to the stickies about flashing Eugene's froyo that doesn't brick. Then back to jfd.
Your phone is fine... or it will be.
Sent from my GT-I9000 using XDA App
Installed driver for the phone, my computer makes the connection sound when I plug in the USB. But it is still not showing as a drive.
And I've been searching for a while now, I seem to be unable to find that thread with Eugenes froyo that doesnt brick.
Get your phone into download mode. Make sure that the USB cable is not plugged in.
Open Odin.. preset everything (PDA,etc) in its respective boxes
Plug your phone in.. Odin should detect a COM#
Press start
And it should work.
Drivers are located: http://forum.xda-developers.com/showthread.php?t=728929 (these work.. try re-installing if above doesn't work)
zephiK said:
Get your phone into download mode. Make sure that the USB cable is not plugged in.
Open Odin.. preset everything (PDA,etc) in its respective boxes
Plug your phone in.. Odin should detect a COM#
Press start
And it should work.
Drivers are located: http://forum.xda-developers.com/showthread.php?t=728929 (these work.. try re-installing if above doesn't work)
Click to expand...
Click to collapse
Cool thanks, it detected the phone and gave me COM4 in yellow. Is that good?
I pressed start and it seems to be stuck at
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> cache.rfs
And the download symbol on the phone went away. Black screen only
Sorry for the noobness, and thanks for the help
christeeezy said:
Cool thanks, it detected the phone and gave me COM4 in yellow. Is that good?
I pressed start and it seems to be stuck at
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> cache.rfs
And the download symbol on the phone went away. Black screen only
Sorry for the noobness, and thanks for the help
Click to expand...
Click to collapse
Try uninstalling the drivers you installed and install the ones I linked above with respect to 32-bit or 64-bit (depending on your OS). I had this problem before, just pull the battery and get it back into download mode and do it again after installing the drivers and restarting. Remember to pre-load all the files before plugging in the usb
zephiK said:
Try uninstalling the drivers you installed and install the ones I linked above with respect to 32-bit or 64-bit (depending on your OS). I had this problem before, just pull the battery and get it back into download mode and do it again after installing the drivers and restarting. Remember to pre-load all the files before plugging in the usb
Click to expand...
Click to collapse
I did that and also used a newer version of odin, and it worked. I have my phone back!
Thanks
christeeezy said:
I did that and also used a newer version of odin, and it worked. I have my phone back!
Thanks
Click to expand...
Click to collapse
Grats Glad to hear that.
Moved of: Samsung Vibrant > Vibrant General
To: Samsung Vibrant > Vibrant Q&A
Please put your questions to: Vibrant Q&A
Follow the suggestions and find what you're looking for!
Closed Thread!
As the title says, today I tried updating my phone to the latest firmware. Samsumg Kies downloaded the new firmware, and the update was going. After it "finished", it said:
"SGH-T959 could not be upgraded
1. Detach and reattach the mobile phone's battery.
2. Reboot the mobile phone, and then try the upgrade again."
So I did all it asked, to go into Emergency Recovery, and my phone does not go into the mode. It's stuck on this black screen with an image like this (Phone .. ! .. PC).
Any help would be much appreciated.
Some other info: I've never done any fancy work on this phone, such as rooting, etc. The only time I touched its firmware was using the Samsumg Kies before to upgrade to 2.1 or 2.2, whatever is the latest one right now.
UPDATE!:
So after trying many times with Odin, and doing the download mode thing, I decided to run Samsung Kies again. In the Emergency Recovery it told me to press the UP and DOWN volume button, but never really explained how. It didnt specify that it was trying to put me into download mode.
So, I went into Samsung Kies, did the STEP by STEP of going into Download mode of this guide http://forum.xda-developers.com/showthread.php?t=848737. The Emergency Recovery mode started working into Kies. I now have my phone back up and running.
NOTE: My screen setup was changed. I had only 3 tabs and now its back to 7, and the apps arent in place (BUT THEY ARE ALL HERE!).
Thank you laylovj for your time and all the help!
SOunds like a softbrick. You better hope that you have backups of everything cause you might have to ODIN back to stock firmware.
I don't mind losing everything, as long as I get it working. Mind pointing me out to a good guide?
Thank you.
Use the ODIN 1.7 from
http://forum.xda-developers.com/showthread.php?t=821625
Get 512.pit and Firmware.zip files from here + guide.
http://forum.xda-developers.com/showthread.php?t=848737
(You might not be able to get to download mode, it's fine, just leave it on the WARNING screen and plug it in. Odin should recognize.
laylovj said:
(You might not be able to get to download mode, it's fine, just leave it on the WARNING screen and plug it in. Odin should recognize.
Click to expand...
Click to collapse
I was about to post about that when you edited it. It does not go into download mode. I will try as soon as the JFD download is done. Thanks so far!
So I downloaded Odin and all the other files. Did the whole thing of going into download mode, even though it didnt change the screen, in Odin, it seemed to recognize my phone as a yellow box showed with 0:[COM4]. The only files that were able to be chosen were PIT and PHONE. When I clicked PDA, no file appeared, and neither did CSC and ETC. So I clicked START, and its now stuck on SetupConnection. It's been there for about 5 minutes now, is this normal?
Also, before upgrading to Froyo, try out some custom roms if you're feeling brave.
And if this ever happens again, pull out battery first, then remove the USB to avoid it again.
Can I fix it first then do a ROM after? I did want to do it before, because my phone was freezing at random times doing basic stuff, but I was afraid it would brick my phone. But right now it can't get any worse lol
I just want it to work, if it works, i'll try a different ROM.
Update: I did the Odin again, and now I got "<OSM> All threads completed. (succeed 0 / failed 0).
Wont go any further then that.
Wait so you didn't choose a PDA? Did you extract the JFD zip file? You weren't supposed to.
laylovj said:
Wait so you didn't choose a PDA? Did you extract the JFD zip file? You weren't supposed to.
Click to expand...
Click to collapse
I'm pretty sure I read somewhere I needed to extract, but guess I was wrong. So this time I re did everything, and was able to select the PDA file. I clicked start, and this is what I got:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
UPDATE:
I am now trying with another version of Odin3 (v1.00 now), and so far I got this:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
Stuck there.
care to screen shot your Odin setup?
Odin 1. tends to get stuck there....battery pull and try again.
Here it is:
http://img684.imageshack.us/img684/9307/odindk.jpg
Like I said, try a battery pull and do it again and I do recommend 1.7..much safer. Try it again with 1.7.
Tried once again with v1.00 and it kept getting stuck at cache.rfs.
So I tried twice with v1.7 and I keep getting this:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
EDIT: Could I try another PDA and PIT file? How does another ROM would work? Is it just other files in the place of these PDA and PIT files?
Try redownloading the files...I really don't know what else to say.
-DO you get a different [COM#] if you try to go to download mode than if you hold the power button? (should come up as warning still)
laylovj said:
Try redownloading the files...I really don't know what else to say.
-DO you get a different [COM#] if you try to go to download mode than if you hold the power button? (should come up as warning still)
Click to expand...
Click to collapse
I have gotten COM3, COM4, and COM5. Pretty sure I did the same steps every time though.
So after trying many times with Odin, and doing the download mode thing, I decided to run Samsung Kies again. In the Emergency Recovery it told me to press the UP and DOWN volume button, but never really explained how. It didnt specify that it was trying to put me into download mode.
So, I went into Samsung Kies, did the STEP by STEP of going into Download mode of this guide http://forum.xda-developers.com/showthread.php?t=848737. The Emergency Recovery mode started working into Kies. I now have my phone back up and running.
NOTE: My screen setup was changed. I had only 3 tabs and now its back to 7, and the apps arent in place (BUT THEY ARE ALL HERE!).
Thank you laylovj for your time and all the help!
Never tried it....you can try heimdall as well, but I really don't know how to use it either...
HI All
I'm wondering if you guys have seen similar problem. I have currently rooted stock ROM on my Mega but want to install CWM so I can take a backup of the system and try out CyanogenMOD11.
Yet, when I try flashing CWM with Odin it looks like this:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> recovery.img
<ID:0/012> NAND Write Start!!
<ID:0/012> RQT_CLOSE !!
<ID:0/012> RES OK !!
<ID:0/012> Removed!!
<ID:0/012> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
At this point phone reboots and when I go to recovery - there is no CWM
I will be grateful for any suggestions.
Thanks
I would suggest you try this http://goo.im/devs/philz_touch/CWM_Advanced_Edition/meliusltexx/philz_touch_6.25.0-meliusltexx.tar.md5 assuming you have the GT-I9205 of course.
Kangburra said:
I would suggest you try this _link_ assuming you have the GT-I9205 of course.
Click to expand...
Click to collapse
I will try that, thanks for suggestion :good:
So I tried the above but have same thing happening.
Everything looks as if it's working OK. Odin picks up the phone, I load the image in PDA.
Have Auto Reboot and F.Reset Time enabled (only).
I hit the start button and it's VERY fast - literally few seconds and I get blue RESET! in the top box in Odin.
What's interesting is that after another two minutes Odin will change to PASS!
But that's looong after my phone booted back to normal operation mode, it will also change to PASS even if I have disconnected my phone
Any suggestions anyone?
==== UPDATE ===
What I also noticed is that after I boot to recovery I'm getting ERROR and NO COMMAND - they will flash on the screen and instead of usual Android Robot I have one on it's side with red exclamation mark over it.
No Command and this point is displayed below the "robot".
This is really irritating
One thing when you are flashing a custom recovery on the mega is once you are done flashing with odin you MUST reboot the phone directly into the recovery mode again for like CWM to appear otherwise if you do not do this the stock recovery will be back, this only has to be done once when you first flash a custom recovery..then it will be okay after that.
And with odin that does the same thing for me it says RESET but it still works and after it will say PASS when the phone is disconnected already, not sure why odin does this but seems to have no effect on the flashing part...hope this helps you out.
starmaster10 said:
One thing when you are flashing a custom recovery on the mega is once you are done flashing with odin you MUST reboot the phone directly into the recovery mode again for like CWM to appear otherwise if you do not do this the stock recovery will be back, this only has to be done once when you first flash a custom recovery..then it will be okay after that.
And with odin that does the same thing for me it says RESET but it still works and after it will say PASS when the phone is disconnected already, not sure why odin does this but seems to have no effect on the flashing part...hope this helps you out.
Click to expand...
Click to collapse
That was is!
Thanks for pointing in the right direction.
I've all the same options in Odin but when it auto-rebooted my phone I have quickly pressed the the buttons for going to recovery and that worked. When powering off from recovery I was given an option to disable stock recovery and now it's all as intended.
THANKS!
Ch3rub said:
That was is!
Thanks for pointing in the right direction.
I've all the same options in Odin but when it auto-rebooted my phone I have quickly pressed the the buttons for going to recovery and that worked. When powering off from recovery I was given an option to disable stock recovery and now it's all as intended.
THANKS!
Click to expand...
Click to collapse
You are welcome.
Ch3rub said:
So I tried the above but have same thing happening.
Everything looks as if it's working OK. Odin picks up the phone, I load the image in PDA.
Have Auto Reboot and F.Reset Time enabled (only).
I hit the start button and it's VERY fast - literally few seconds and I get blue RESET! in the top box in Odin.
What's interesting is that after another two minutes Odin will change to PASS!
But that's looong after my phone booted back to normal operation mode, it will also change to PASS even if I have disconnected my phone
Any suggestions anyone?
==== UPDATE ===
What I also noticed is that after I boot to recovery I'm getting ERROR and NO COMMAND - they will flash on the screen and instead of usual Android Robot I have one on it's side with red exclamation mark over it.
No Command and this point is displayed below the "robot".
This is really irritating
Click to expand...
Click to collapse
I got same problem when i flashed cwm by phil with odin, what i did is to uncheck autoreboot in odin so after odin finish flash recovery image you need to turn off manually by long pressing power button, and then just boot into recovery, reboot system now and select yes disable stock recovery when prompted by cwm.
Sent from my GT-I9205 using XDA Free mobile app
This does not work for me?
SPH-L600 (Sprint) Galaxy mega
Android: 4.2.2
Baseband: L600vpubne4
Build: KOT49H.L600VPUBNE4
HI
I got here a bricked i9300.
It freezes on Samsung logo.
I cant open recovery, but it does enter download mode.
First thing I tried was flashing stock firmware via Odin: I got "There is no PIT partition"
So I closed Odin and reopened it and tried flashing the PIT file.
It froze on SetupConnection.
I shut off the phone and entered download mode again and tried to flash the PIT.
Now it froze on Get PIT for mapping..
I closed Odin and reopened it... Froze on SetupConection.
Shut of the phone... Download mode... Odin...
I set the PIT and marked Nand Erase All
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Every time I try to do something via Odin the phone seems to freeze and wont pass trough SetupConnection anymore.
If I restart it to download mode, it will try to do something but I get those errors.
If I shut it down and put it to charge, it will take longer than usual to show the static battery icon (the one with a circle), and wont pass trough it. It will freeze there.
I also tried the Kies tool where you put Model and S/N, it finds the phone, I accept the terms and then get a message that "this version cannot be updated".
WHat the hell can I do? Is this motherboard gone for good?
Very much the same here! I hope there is a solution for this problame
Did you try ticking repartition in Odin and flash firmware with pit. Hope that'll do.
Sent from my toaster
foggydisaster said:
Did you try ticking repartition in Odin and flash firmware with pit. Hope that'll do.
Sent from my toaster
Click to expand...
Click to collapse
Yes it will start by trying to repartition and freeze at "Get pit for mapping.."
ajcmaster said:
HI
I got here a bricked i9300.
It freezes on Samsung logo.
I cant open recovery, but it does enter download mode.
First thing I tried was flashing stock firmware via Odin: I got "There is no PIT partition"
So I closed Odin and reopened it and tried flashing the PIT file.
It froze on SetupConnection.
I shut off the phone and entered download mode again and tried to flash the PIT.
Now it froze on Get PIT for mapping..
I closed Odin and reopened it... Froze on SetupConection.
Shut of the phone... Download mode... Odin...
I set the PIT and marked Nand Erase All
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Erase...
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Every time I try to do something via Odin the phone seems to freeze and wont pass trough SetupConnection anymore.
If I restart it to download mode, it will try to do something but I get those errors.
If I shut it down and put it to charge, it will take longer than usual to show the static battery icon (the one with a circle), and wont pass trough it. It will freeze there.
I also tried the Kies tool where you put Model and S/N, it finds the phone, I accept the terms and then get a message that "this version cannot be updated".
WHat the hell can I do? Is this motherboard gone for good?
Click to expand...
Click to collapse
Try using Samsung Kies 3. Go to Tools, then Firmware Upgrade and Initialisation.
This happened to me and I was able to unbrick my phone.
user150 said:
Try using Samsung Kies 3. Go to Tools, then Firmware Upgrade and Initialisation.
This happened to me and I was able to unbrick my phone.
Click to expand...
Click to collapse
SUPERTHANKS!!!!!!!!!!!! Worked for me!!:good:
nancygreece said:
SUPERTHANKS!!!!!!!!!!!! Worked for me!!:good:
Click to expand...
Click to collapse
I will give it a go today ! Thanks !
I tried to use KingoRoot and apparently it's "bricked" my tablet. I've done lots of reading and I'm stuck, and need help please.
1. I have latest Odin, 3.10.7 from odindownload
2. My tablet is a SM-T560NU, and came with 5.1.1
3. I found a recent image for my exact unit model, and have downloaded it: BNN-T560NUUEU1AOH6-20151215094559
The instructions I have seen everywhere say to launch Odin3, wait for the tablet to connect (it does), load the image into "AP" (I do), and turn ONLY on options "auto reboot" and "F. Reset Time" (which means keep re-partition off, which they stress). When I click start, it goes about 5 minutes, then says this:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
Help, any ideas? I've tried 2 images.. the one I said above, and another for a SM-T560 (non-NU), and both give the exact same above fail in Odin3.
figure anything out? in th eprocess of downloading and fixing my sm-t560nu tablet also.
make sure you have the correct firmware rom, there's sm-t560 and there's sm-t560nu
same problem, rooted it last night with kingroot, worked fine until i turned it off and tried to turn it back on
did it take forever to download your firmware? if not can i ask where you got it from cuz mine is taking 7 hours to download
well i got mine all up and running, if you're in canada you might have the wrong rom file because the one i needed for my samsung galasy tab E "sm-t560nu" the file name started with xac and not bnn, i had to get mine from
samsung-firmware . org
and pay i think it was 5.99 usd, did exactly what it said at the bottom of the page for the instruction in odin and everything worked great but make sure to use the same email account u used originally when your setting up that tablet on its first boot up
was a lil confused since the instructions said to click on ap/pda and there's only ap in odin3 but ap/pda is renamed to just ap in the new odin.
good luck
Loading a new ROM in Odin, although I 100% had correct one, did NOT help. I could try 1000 times, and it wouldn't budge. The trick was a post I found on another site that talked about a recovery mode.... a hard reset.
What I actually had to do was the following:
1. Go into RECOVERY MODE, and do a reset. (Doesn't unbrick, but allows Odin to work)
2. Go into DOWNLOAD mode, and then use Odin to load image.
Here are the steps for both:
Recovery Mode Samsung Galaxy J1 SM-J120F
Turn off the device
Press and hold Volume UP key + Home Key, while pressing these keys then press and hold Power key for a while
Release all key when Android or Samsung logo appear then you will see Android System Recovery
Use Volume keys to select Menu
Use Power key to Confirm
Download Mode or ODIN Mode
Turn off the device
Press and hold Volume Down key + Home Key, while pressing these keys then press and hold Power key for a while
Release all key when you see ODIN Mode / Download Mode
Use Volume Up key to continue
Use Volume Down key to cancel ( Restart the device )
As for firmware, I got mine from (I can't post url's here yet, forum rules) a place called : You Mobile dot Org. ... for free.
Now if we can find a way to actually ROOT it, I'd be thrilled.
Any help on this? i just got this message and waster an hour downloading the firmware, and still stuck with odin.
i dont see anything saying menu in Recovery Mode
This is my Odin message
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> PK-
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've rooted my tablet with kingroot and rebooted several times. My tablet still works fine. My tablet is a sm-t560nu
Use Odin 3.07
This method works best with Odin 3.07 using BNN rom.
hello same thing happened to me and when i try to boot my device it says custom binary locked by frp.is that what happened to you? if so please tell me exact steps.
Rovexx said:
hello same thing happened to me and when i try to boot my device it says custom binary locked by frp.is that what happened to you? if so please tell me exact steps.
Click to expand...
Click to collapse
Read what I wrote above... I tell you how to unbrick it.
First go into recovery mode on tab, then get odin and download image, then use odin to load image into tab using odin and tab in download mode.
I can't find this firmware anywhere. My 8yr old used kingroot n killed tab. Someone please help.. Sm-t560nu wife is Bout to kill him if I can't fix with odin.
DesertEagleSlim said:
I can't find this firmware anywhere. My 8yr old used kingroot n killed tab. Someone please help.. Sm-t560nu wife is Bout to kill him if I can't fix with odin.
Click to expand...
Click to collapse
ya i'm still ****ed up too. still haven't found a solution. sorry. wish i could help
kingroot and OEM unlock
use samsung smart switch to fix your SM-T560NU tablet if you used kingroot. I couldn't boot because it said ... "custom binary blocked by FRP" used smart switch it restored the tablet to factory settings. the solution is to unlock developer options and select "OEM unlock" then use king root. king root should warn the user about this issue. Good luck!
ThePopcanKid said:
ya i'm still ****ed up too. still haven't found a solution. sorry. wish i could help
Click to expand...
Click to collapse
Found a copy of firmware on sammobile just register and download. It's super slow if u don't pay but it will finish. Fixed tablet n wife didn't kill me. No more kingroot for that tab. Although kingroot did work for the tab4 that I found in a bush (obviously stolen and ditched cause they couldn't bypass the screen lock)
I have full root, sticks after multiple reboots. I used kingroot, forced it to root, then after de-bloating, unrooted. It has been hanging out in that state for a week while I worked up the nerve to try turning off OEM under development options and telling it to root again, which I did this morning. Is running like a champ now.
Next problem is there is no custom recovery, so I am working to get xposed installed by zip somehow and be able to backup.
Sent from my SM-T560NU using XDA Free mobile app
pushabutton said:
I have full root, sticks after multiple reboots. I used kingroot, forced it to root, then after de-bloating, unrooted. It has been hanging out in that state for a week while I worked up the nerve to try turning off OEM under development options and telling it to root again, which I did this morning. Is running like a champ now.
Next problem is there is no custom recovery, so I am working to get xposed installed by zip somehow and be able to backup.
Sent from my SM-T560NU using XDA Free mobile app
Click to expand...
Click to collapse
You can use Flashfire to install Xposed if you convert to supersu first.
I have been working on TWRP with a tester (I don't own this device) however it doesn't boot yet, I have a feeling I need a permissive kernel, but Samsung have not released the source code yet.
DEVICE TREE:https://github.com/ashyx/TWRP_Samsung_gtelwifi?files=1
I could not get supersu to install no matter what I do so am stuck for now. Has anyone had any experience using flash Gordon to install zips, or know how to get supersu to install?
pushabutton said:
I could not get supersu to install no matter what I do so am stuck for now. Has anyone had any experience using flash Gordon to install zips, or know how to get supersu to install?
Click to expand...
Click to collapse
See post #65 onwards.
http://forum.xda-developers.com/showthread.php?t=3262864
cablematicman said:
use samsung smart switch to fix your SM-T560NU tablet if you used kingroot. I couldn't boot because it said ... "custom binary blocked by FRP" used smart switch it restored the tablet to factory settings. the solution is to unlock developer options and select "OEM unlock" then use king root. king root should warn the user about this issue. Good luck!
Click to expand...
Click to collapse
How did you use smart switch when tablet won't boot. I tried hooking up to computer and it has it doesn't recognize tablet.
thinv said:
How did you use smart switch when tablet won't boot. I tried hooking up to computer and it has it doesn't recognize tablet.
Click to expand...
Click to collapse
Boot into download mode POWER + VOL DOWN +HOME