I just bought a motorola atrix 4g manufacturer refurbrished from US and i want to use custom ice cream rom on it, i've managed to root the phone following the commands in the previous threads. But i'm unable to unlcock the bootloader, i've tried all methods founds here. The phone is running on 2.3.6 Gingerbread 4.5.141.MB860.ATT.en.US. I'm unable to use android recovery as well as Customrom recovery either, the error i get is 'fail to boot 2'......I flashed back to stock with SBF 2.3.6, 4.5.141 and had no fix with wifi/bluetooth bugs.
I'm unable to use wifi/bluetooth, i get wifi error and bluetooth fails to switch on and whenever i try to switch on wifi the phone restarts.
mulfty said:
I just bought a motorola atrix 4g manufacturer refurbrished from US and i want to use custom ice cream rom on it, i've managed to root the phone following the commands in the previous threads. But i'm unable to unlcock the bootloader, i've tried all methods founds here. The phone is running on 2.3.6 Gingerbread 4.5.141.MB860.ATT.en.US. I'm unable to use android recovery as well as Customrom recovery either, the error i get is 'fail to boot 2'......I flashed back to stock with SBF 2.3.6, 4.5.141 and had no fix with wifi/bluetooth bugs.
I'm unable to use wifi/bluetooth, i get wifi error and bluetooth fails to switch on and whenever i try to switch on wifi the phone restarts.
Click to expand...
Click to collapse
You may have an unlockable bootloader.
Your wifi / BT are on the same chip. If the chip gets damaged, neither works.
I sell phones on Ebay and have worked on a few atrix phones.
1. The wifi/bt chip is burned out, it cannot be fixed only by replacing the whole motherboard. Has it been this way since you bought it? If so then the seller screwed you.
2. This is the way I personally BL unlock atrix phones:
A. Boot into RSD
B. Flash "4547-fix-try2.sbf" using RSD lite 5.7
Note this will soft brick your phone. You will get an error like 0x000 don't freak out, it will ask you what to boot into, RSD or what, choose fastboot.
C. Open a command prompt and navigate to your adb and fastboot files. Make sure your device is listed under "fastboot devices" then "fastboot oem unlock" This will return a string of characters. Next retype that character code "fastboot oem unlock XXXXXXXXXXXXXXXXXXXXXXXXX"
D. If you did it right it will say your bootloader is now unlocked.
E. Next "fastboot flash recovery recovery.img"
Where recovery.img is a flashable recovery CWM or TWRP (I prefer TWRP because it's touch based)
These instructions assume you understand how to use RSD lite and fastboot. You can find other similar methods on the forums.
Related
PC will not identify phone in RSD or fastboot. I have tried all drivers I can find, have uninstalled and reinstalled all software, the drivers install in each mode but RSDlite or the official moto software updater will not ID the phone when connected...
I have tried 64 and 32 windows and 3 different cables just to be sure....
Anyone have an idea what to do? I have locked an unlocked this thing once before the 4.5.91 update and again after. I used the official Motorola Software Updater to "update" back to locked stock and have had this issue ever since then....
Fixed: Belkin USB print and storage drivers had to be removed.
* delete * 10 chars
anyone??????????????
Simple question, do you have debugging turned on? I was having a similar problem, when i realized it was off I totally face palmed myself
Yesy I have tried everything I can think of... the issue is before booting into android not after... something is blocking my phone from getting picked up by RSDlite and the moto update tool... everything in android functions fine, i have turned USB debug on and off both.
I was able to root through fastboot with no issues so it is ok, but I will be d*&$^d if I can get rsd running so I can unlock... it's not like this is new to me I have unlocked this thing twice before...
halfevildruid said:
I was able to root through fastboot with no issues so it is ok, but I will be d*&$^d if I can get rsd running so I can unlock... it's not like this is new to me I have unlocked this thing twice before...
Click to expand...
Click to collapse
You are trying to unlock the same atrix?
Once it's unlock, it remains!
Even if it doesn't show it at booting(maybe disapeared after installing a rom..)
Sent from my MB860 using XDA App
Nope. I am definately locked again. I flashed the official motorola GB software update over my existing GB software to attempt to revert to locked and stock again. It worked but now I am unable to unlock. RSDlite AND the same Moto update do not see my phone in RSD mode.
halfevildruid said:
Nope. I am definately locked again. I flashed the official motorola GB software update over my existing GB software to attempt to revert to locked and stock again. It worked but now I am unable to unlock. RSDlite AND the same Moto update do not see my phone in RSD mode.
Click to expand...
Click to collapse
Actually, once a bootloader is unlocked, its unlocked for good. By reflashing to stock, all that you did was copy over pudding (the SBF file that you flashed when you unlocked the bootloader). This hides the "Unlocked" text in the top corner. To reshow this text and regain access to locked fastboot features, you must reflash pudding via the "Unlock SBF file" available here:
briefmobile.com/how-to-unlock-the-atrix-4g-bootloader
Im not sure why you can't get into RSD mode. Try the following:
- Insure that your volume buttons work
- Unplug phone, take out battery
- wait 10 seconds
- reinsert battery
- hold down UP (not down, I made that mistake once) volume button firmly
- press and hold power button
- phone should say "Starting RSD Mode"
To enter Fastboot mode do the same steps as above, only press the down volume button instead. When the word "FastBoot" appears, press the up volume button.
I can get into rsd and fastboot on the phone. The driver in rsd installs as se flash where it used to install as nf flash. Fastboot is working fine, I was able to reroot.
The problem is rsd does not identify my device and allow me to flash. I am thinking it is in the se flash driver instead of the previous nf flash driver.
Anyone have an opinion?
Sent from my MB860 using Tapatalk
SOLVED!!!
So I figured it out! As it happens I picked up a new Belkin 750 router with networked USB support a few days back for my ext drive and printer. Apperently the Belkin drivers were the culprit! After uninstalling them everything picked up and ran like it should. Some of you devs and folks creating guides should note this in the posts so we can give folks a heads up in case it happens to them. I am sure this will happen to someone else.
I have started to follow the process to Unlock/root my atrix phone found here
http://forum.xda-developers.com/showpost.php?p=15989846&postcount=1
But after the first step I used RSD and flashed my rom and Now I get Bootloader error and I am able to select a new way of booting my phone (ie RSD, Fastboot, NvFlash, BP HW Bypass RSD...... BP Tools)
If I try android recovery I get the error Magic Value Mismatch.
What Should I do?
Is my Phone Hard Bricked?
Here is a little more information about what I did:
I tried to use this website:
http://briefmobile.com/how-to-unlock-the-atrix-4g-bootloader
to unlock my bootloader and I ran into an error when I typed "fastboot oem unlock"
and it seemed that people didn't understand how to fix that error. So I then surffed forums to find information.
I ran into this post by Clear-Fire:
http://forum.xda-developers.com/archive/index.php/t-1221042.html
where he says "well you should try and flash Download ATT 2.3.4 pudding+root here (http://www.multiupload.com/C0I82IXH7V) through RSDLite 5.3.1 link (http://forum.xda-developers.com/attachment.php?attachmentid=634879&d=1308872277)"
Then That leads me to today.
Answer.
If you are seeing the different
ways to start the phone your phone is not bricked it is only "soft Bricked" meaning we can fix it.
Go to the following forum and download the application and run it on your computer: it has a way to fix the soft brick and then unlock your phone.
http://forum.xda-developers.com/showthread.php?t=1182871
I was trying to unlock the BL in my Atrix via Fastboot OEM Unlock, and when that failed I moved on to other, more complicated methods including RSD Lite 5.5 and sbf flashing.
Now when I power up my Atrix I get no logo, just "failed to boot 0x1000
No OS detected, going to RSD mode in 5 seconds."
And literally everything I do will not work. Fastboot does nothing. RSD fails everything, says "Unable to retrieve interface handle (0x7027); phone connected"
When I connect in RSD Mode now, my Atrix shows up as SE Flash Olympus under the Model column, as it did before, rather than the typical NS Flash Olympus.
I'm trying to flash the full 4.5.91 sbf from the IHOP thread that includes an unlocked BL, but it keeps failing.
Edit: It gets to 99% And then says "Switching phone to BP Passthrough mode," but my phone still fails to boot (0x1000) and I have to pick what mode to put it in. I see now it's not BP HW Bypass RSD. Does anyone know?
Did you try to pull the battery and then boot into fastboot (Hold Vol down & Power) and then issue the unlock commands?
Mecharuva said:
I was trying to unlock the BL in my Atrix via Fastboot OEM Unlock, and when that failed I moved on to other, more complicated methods including RSD Lite 5.5 and sbf flashing.
Now when I power up my Atrix I get no logo, just "failed to boot 0x1000
No OS detected, going to RSD mode in 5 seconds."
And literally everything I do will not work. Fastboot does nothing. RSD fails everything, says "Unable to retrieve interface handle (0x7027); phone connected"
When I connect in RSD Mode now, my Atrix shows up as SE Flash Olympus under the Model column, as it did before, rather than the typical NS Flash Olympus.
I'm trying to flash the full 4.5.91 sbf from the IHOP thread that includes an unlocked BL, but it keeps failing.
Click to expand...
Click to collapse
Of course, that's the first thing I did. If it had worked, I wouldn't have a bricked Atrix now. I read somewhere else here on XDA that if your Atrix shows up as "SE" in RSDLite, rather than "NS," you have an Atrix that ATT used to use for testing and support. Not sure how correct that is, but it's possible, considering this is a refurb I bought as a part of the ATT 3rd Party Reseller concession line program. (sub-$50 bill with Unlimited web ftw)
Edit: And now.. for whatever reason, fastboot oem unlock worked. But will my phone boot? It just pops up the M logo, with "Unlocked" in the upper corner. Doesn't appear to be doing anything though.
Edit 2: Now my Atrix shows up as NS in RSDLite. Perhaps there is hope. Flashing the full 4.5.91 sbf from the IHOP thread.
Edit 3: Worked. Now my Atrix is unbricked. Pardon my naivete.
That's quite alright. The only reason I asked is because for people who flash pudding on an Atrix that's already been updated to GB will encounter a "soft brick" in which they need to go through a separate procedure. That's all. Didn't mean to imply you didn't know what you were doing. Glad you got it working.
Mecharuva said:
Of course, that's the first thing I did. If it had worked, I wouldn't have a bricked Atrix now. I read somewhere else here on XDA that if your Atrix shows up as "SE" in RSDLite, rather than "NS," you have an Atrix that ATT used to use for testing and support. Not sure how correct that is, but it's possible, considering this is a refurb I bought as a part of the ATT 3rd Party Reseller concession line program. (sub-$50 bill with Unlimited web ftw)
Edit: And now.. for whatever reason, fastboot oem unlock worked. But will my phone boot? It just pops up the M logo, with "Unlocked" in the upper corner. Doesn't appear to be doing anything though.
Edit 2: Now my Atrix shows up as NS in RSDLite. Perhaps there is hope. Flashing the full 4.5.91 sbf from the IHOP thread.
Edit 3: Worked. Now my Atrix is unbricked. Pardon my naivete.
Click to expand...
Click to collapse
Of course, thanks live.
Ok so apparently I flashed a the kitchen sink rom and when phone booted up it stop and said fail to boot 2 but I flashed the and files in the video from qbking77 and now it says fail to boot 4 can anybody help me please. It the only phone I got and I'm not available for an upgrade till february
Robert5686 said:
Ok so apparently I flashed a the kitchen sink rom and when phone booted up it stop and said fail to boot 2 but I flashed the and files in the video from qbking77 and now it says fail to boot 4 can anybody help me please. It the only phone I got and I'm not available for an upgrade till february
Click to expand...
Click to collapse
What version soft ware did you start with.
the android version ? i was running on 2.3.5 it first said fail to boot 2 and thn after i flashed the sbf file it went to boot 4 do u know how i can fix this
Robert5686 said:
the android version ? i was running on 2.3.5 it first said fail to boot 2 and thn after i flashed the sbf file it went to boot 4 do u know how i can fix this
Click to expand...
Click to collapse
You can't flash custom ROMs with a locked bootloader
Sent from my MB855 using xda app-developers app
Yeah i didnt know that but idk y does the bootloader have to be unlocked cuz i flashed the beats audio one and didnt do this
What sbf did you flash?
Sent from my MB855 using xda app-developers app
mof9336 said:
What sbf did you flash?
Sent from my MB855 using xda app-developers app
Click to expand...
Click to collapse
Also having the same issue, I just got root, and I tried to install Jellybean from Jokersax with my battery at 5% which was dumb, but anyways now I get failed to boot 4, I can get it into fastboot protocol support, or rsd mode, and that's it, I've tried to flash some stock files, but no good, I also have a locked bootloader & am on 2.3.5
i flashed the one from qbking77 video i only flashed the one and my batery was drained cuz it wasnt full but the proccess said succes but it went to fail to boot 4 and now it says battery to low to flash but i can get a new battery real quick i jux need to know wat sbf file to flash do u know any that i can flash and would work like i said its the only phone i have and im not available for an upgrade till later and i need my phone
Failed to boot 4 Starting RSD Mode
The Story:
I started having issues with the phone becoming slower and slower and crash prone so i figured this would be a good time to flash an alternate rom. I have had root for some time and i unlocked the boot loader probably about two weeks ago. I had tried a few roms by Th3Bill and i kept having issues so i thought id try to re-lock the boot loader as i couldn't flash any of his roms even with is recovery in place to see if unlocking it again would solve my issue. Also i was running 2.3.4 NOT 2.3.5 so it wasn't due to that.
I just followed the steps outlined here from Link:
Relocking without Full SBF flash
Factory reset phone Menu/Settings/Privacy/Factory Data Reset DO NOT SKIP THIS STEP
Reboot phone into fastboot mode: VOL down/Power. Use VOL down to scroll though options til you see "fastboot" then VOL up to enable. and connect phone to computer
Open command prompt in the moto-fastboot folder and type the following using the <enter> key after each command:
moto-fastboot devices
moto-fastboot erase recovery
moto-fastboot flash recovery stock_recovery.smg
moto-fastboot reboot
Disconnect phone from computer
Start RSD Lite on your computer
Reboot phone into RSD mode: VOL down/Power. Use VOL down to scroll though options til you see "RSD" then VOL up to enable.
Connect phone to computer.
Flash nopudding4u.sbf.
Close RSD Lite and disconnect phone.
Reboot phone
Once i completed the Flash nopuding4u.sbf step it failed giving the status: "Failed flashing process. Failed Flashing process. Phone[0000]: THe "Secure_Motorola_Flash" Interface could not be found. The super-file is secure and for re-flash; the phone needs a super-file that is not secureand not for reflash. (0x7066);Phone connec"
It is not just booting to the first Motorola Dual Core Technology splash screen and showing:
Failed to boot 4
Starting RSD Mode
I've been looking for a solution to the issue for about 30 minutes and have found nothing helpful.
Nopudding4u.sbf relocks your phone, however I would recommend using the 198_7.sbf file instead. U can still unlock with pudding.sbf but you will be able to get back running.. after u flash the stock sbf u will probably need to go into recovery and do a factory reset.
Sent from my MB855 using xda app-developers app
Did you fix,
Tempest_Inc said:
The Story:
I started having issues with the phone becoming slower and slower and crash prone so i figured this would be a good time to flash an alternate rom. I have had root for some time and i unlocked the boot loader probably about two weeks ago. I had tried a few roms by Th3Bill and i kept having issues so i thought id try to re-lock the boot loader as i couldn't flash any of his roms even with is recovery in place to see if unlocking it again would solve my issue. Also i was running 2.3.4 NOT 2.3.5 so it wasn't due to that.
I just followed the steps outlined here from Link:
Relocking without Full SBF flash
Factory reset phone Menu/Settings/Privacy/Factory Data Reset DO NOT SKIP THIS STEP
Reboot phone into fastboot mode: VOL down/Power. Use VOL down to scroll though options til you see "fastboot" then VOL up to enable. and connect phone to computer
Open command prompt in the moto-fastboot folder and type the following using the <enter> key after each command:
moto-fastboot devices
moto-fastboot erase recovery
moto-fastboot flash recovery stock_recovery.smg
moto-fastboot reboot
Disconnect phone from computer
Start RSD Lite on your computer
Reboot phone into RSD mode: VOL down/Power. Use VOL down to scroll though options til you see "RSD" then VOL up to enable.
Connect phone to computer.
Flash nopudding4u.sbf.
Close RSD Lite and disconnect phone.
Reboot phone
Once i completed the Flash nopuding4u.sbf step it failed giving the status: "Failed flashing process. Failed Flashing process. Phone[0000]: THe "Secure_Motorola_Flash" Interface could not be found. The super-file is secure and for re-flash; the phone needs a super-file that is not secureand not for reflash. (0x7066);Phone connec"
It is not just booting to the first Motorola Dual Core Technology splash screen and showing:
Failed to boot 4
Starting RSD Mode
I've been looking for a solution to the issue for about 30 minutes and have found nothing helpful.
Click to expand...
Click to collapse
Hello, did you fix your phone. i am in the same issue now.. please guide me or help me to fix the phone.I have been trying for 3 days,, thanks.
Tried to flash MIUI without unlocking the bootloader
keljoe2804 said:
Also having the same issue, I just got root, and I tried to install Jellybean from Jokersax with my battery at 5% which was dumb, but anyways now I get failed to boot 4, I can get it into fastboot protocol support, or rsd mode, and that's it, I've tried to flash some stock files, but no good, I also have a locked bootloader & am on 2.3.5
Click to expand...
Click to collapse
It is was initially stuck on failed to boot 2 and Starting RSD mode. Then I used RSD lite to flash the stock sbf, and my computer went to sleep in the middle of the flash and failed. Now it is stuck on Failed to boot 4, Starting RSD mode, Battery is too low to flash.
I am not in the US right now, so cannot take it to the Sprint store. PLEASE HELP!!!
I am having a problem. I was trying to upgrade to Jelly bean 4.1 on this Atrix 4g. I tried to go through the steps that it gave online with the CM10 n Cyro and all. Long story short it couldn't find the rom within the zip or something of that nature. In other words, it screwed me over. I can't get back into recovery. It's been giving me this error:
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Before it was giving me just:
Failed to boot 4
Starting RSD mode
I had tried reseting to factory through the moto-fastboot but of course it failed. I have been tryin like crazy to flash various SBF from 2.3.5 to 2.3.6. I was originally at 2.3.6 but for what ever reason when I try the RSD lite it gives me the error after it executes "Phone did no re-enumerate after RAM downloader was sent". (0x703e). I have been reading forums literally all day. Perhaps I am not understanding something therefore I am missing it but maybe one of you guys could help me out with this? Maybe there is a real simple fix or maybe I completely ruined it? Either way it would be nice to get some help on this. Basically when I was trying to upgrade to 4.1 I followed "How to upgrade the Atrix 4G to Android 4.1.1 Jelly Bean via CyanogenMod 10" off of the androidauthority website. I got to step 9 but it couldn't find the ROM, by then it was too late.
UPDATE: So I got just that and RSD was flashing it until it reached yet another error:
failed flashing process. Failed flashing process. Phone[0000]: error switching phone BP pass through mode (0x70BE); phone disconnected.
Help?
majorrazer said:
Help?
Click to expand...
Click to collapse
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
saldirai said:
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
Click to expand...
Click to collapse
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
majorrazer said:
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
Click to expand...
Click to collapse
Do you have an unlocked bootloader? Does the word "Unlocked" appear when you power the phone on? You must have an unlocked bootloader for sure. IF not, you must unlock it.
his is the guide you were following;
http://www.androidauthority.com/atrix-4g-mb860-android-4-1-1-jelly-bean-cyanogenmod-10-cm10-106639/
As said there, it requires unlocked, rooted Atrix with with ClockworkMod Recovery installed
I guess you can still unlock the bootloader and install cwm recovery. Just search and find instructions.
HEY
i have the same problem also.... and the same error...
is your phone fix already?
could you tell me how?
SVF: 108:failed to boot 3 starting RSD mode
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
salimdawar said:
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
Click to expand...
Click to collapse
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
salimdawar said:
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
Click to expand...
Click to collapse
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Yes already install this file from Net
"Motorola_End_User_Driver_Installation_5.1.0_64bit "
and not expect any thing else about flashing of my device.
Before Motorola Atrix 4G, i were used in passed Samsung S1, S2, S3, & T989 (T-Mobile S2 version). All these andriod sets were very easily hack or Root and can install Roms easily .
But Moto Atrix 4G can me upset and sad.
kindly help me to re-connect my self to the andriod world by this Motorola Atrix 4G, thanks
Hey guys I'm having trouble getting to RSS mode my phone comes on then it says entering nv flash recovery mode then the phone dies so I need help trying to get into my phone to flash the sbf file
Sent from my GT-N7105 using XDA Premium 4 mobile app
Need Help regarding Motorola Atrix Mb 861.
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
kamal.navigator said:
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
Click to expand...
Click to collapse
Were you bootloader unlocked before getting this message?