Hello all
My dad own a HD2, the flat cable has been replaced. When you turn it on, you just see a white screen sometimes you see HTC logo, and the down left side you see
R 2.05.51.05_2
G 15.28.50.070
B 1.48.71294
We went into 3 colour mode, but we can't make any factory reset.
I tried to flash HSPL but everytime i get an error (image attached)
Stock one is SPL-1.42.0000 XE
I run windows 7 x64bit
can someone please help me?
Update: I have downloaded RUU stock rom from xda, and after 1% its says ERROR 270 update error the image file is corrupted. check your update utility
efi2222 said:
Hello all
My dad own a HD2, the flat cable has been replaced and we tried to make factory reset but without any luck
as far as i know there is no way to flash stock rom through the recovery mode (3 colour mode) with original SPL
It's SPL-1.42.0000 XE
I tried to flash hard spl and it fails everytime i get an error CRITIAL ERROR (image attached)
I run windows 7 x64bit
can someone please help me?
Update: I have downloaded RUU stock rom from xda, and after 1% its says ERROR 270 update error the image file is corrupted. check your update utility
Click to expand...
Click to collapse
Try task 29 wipe phone re download the original ruu and retry . are you using a t mobile us based hd2 ? if so you need specific rom or you will brick device !
also read these 1st to make sure you are doing it right, you should not need to return to stock to flash.
[TUT] Flashing your First GSM USA 1024LEO ONLY!! (For Noobs) http://forum.xda-developers.com/showthread.php?t=653614
[GUIDE] Flashing Your First HD2 NAND Android Rom [For Newbs] http://forum.xda-developers.com/showthread.php?t=893948
[GUIDE] Flashing Your First HD2 Clockwork Mod Android Rom [For Newbs] http://forum.xda-developers.com/showthread.php?t=1044830
task 29?
i can't make a factory reset. I have tried original ruu i get the same error
i tried to find it though htc but i don't see the download section there....
I know i must flash the same model, it's not a t-mobile phone, it's the regular one (99HJY035-00)
http://uk.hardware.info/productinfo/89425/htc-touch-hd2-uk
What can i do?
Follow the link on flashing android and see if it works . If it does then stick with that !
Sent via old skool carrier pigeon
---------- Post added at 01:52 AM ---------- Previous post was at 01:50 AM ----------
Ruu error might be miss match with imei original firmware. Go for Android !
Sent via old skool carrier pigeon
I prefer WM.
I know, but i can't find th place to enter my imei to download original RUU from htc site. Why HSPL doesn't work?
efi2222 said:
I prefer WM.
I know, but i can't find th place to enter my imei to download original RUU from htc site. Why HSPL doesn't work?
Click to expand...
Click to collapse
Its been a long time but im wondering if your problem is goldcard related, you really need somebody who has more expereince recently with wm as my memory is not so good on this now im afraid, hold on what exactly word for word is the error when installing hspl? does it say anything about missing files? are you flashing in bootloader mode (3 colours) and are you running the flasher as administrator???? right click run as administrator??
Originally Posted by powerofthink
1. Use Task29 tool on HD2 toolkit. (it erase all of your rom)
2. HD2 Toolkit 4.2.0.1;Use this tool. it has own HSPL (and also Task29, Magldr, Recovery) tool. choose 2.08.HSPL.
http://www.mediafire.com/?2qz0xa7xfxney47
(after this, if you want to load 3.03.HSPL, then use your HSPL4 tool)
3. after that install this radio rom;Radio ROM 2.15.50.14;
http://www.mediafire.com/?1th8o158r2t6dba
4. And after that you can install original win 6.5 RUU rom or any custom win 6.5 rom. [/QUOTE]
HSPL3 says;
Quote:
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
Hope this helps source:http://forum.xda-developers.com/showthread.php?t=611433&page=355
I tried to download your tool. clicked HSPL then tried to flash 2.08 HSPL
i get the same error like in the first picture
CRITICAL ERROR
flow: 00000006
Error code: 00000014
Description: Unkown
yeah i run it from the bootloader mode, and i do run it from administrator
efi2222 said:
I tried to download your tool. clicked HSPL then tried to flash 2.08 HSPL
i get the same error like in the first picture
CRITICAL ERROR
flow: 00000006
Error code: 00000014
Description: Unkown
yeah i run it from the bootloader mode, and i do run it from administrator
Click to expand...
Click to collapse
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
---------- Post added at 11:34 PM ---------- Previous post was at 11:30 PM ----------
swukjay said:
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
Click to expand...
Click to collapse
Also you can factory reset by holding both the up and down volume buttons down at the same time and switching the device on with the buttons still held down !
swukjay said:
Your flasher looks different to mine I use try this one I uploaded for you
http://rapidgator.net/file/59704072/HSPL4.zip.html
---------- Post added at 11:34 PM ---------- Previous post was at 11:30 PM ----------
Also you can factory reset by holding both the up and down volume buttons down at the same time and switching the device on with the buttons still held down !
Click to expand...
Click to collapse
I tried also your tool same error
as i wrote at the first message i can't make factory reset god knows why.
efi2222 said:
as i wrote at the first message i can't make factory reset god knows why.
Click to expand...
Click to collapse
because theres no rom on the phone to perform a hard reset on.
samsamuel said:
because theres no rom on the phone to perform a hard reset on.
Click to expand...
Click to collapse
Well I hope you can solve this one as I have to admit defeat, I know is the error code can indicate a damaged file but he has re-tried with a new flasher and its the same error, I was wondering if it was a goldcard issue as I seem to remember that can cause a flash fail, but we don't use goldcards anymore, I suppose it is possible its bricked but if its entering the tri coloured screen it should flash, so I am stumped, your turn lol
How the rom got deleted? we just replaced flat cable
Anyway, there is a way that i can do flash the rom?
i was assuming you'd done a task29, (i dont read back previous posts, it'd take me forever, heh, so sometimes i miss / miss-remember something)
Just had a quick 20mins reading and googling, , strange thing is, , your line "B 1.48.71294" , , , thats an odd looking rom version, it would normally be something like 1.43.206.4, , where the .206. gives the rom locale, and carrier (206 is O2 uk, for example)
71294 is (i think) a build number, something like that, but i dont remember it ever being displayed on the start screen (course its been a loong time since i booted winmo)
If i remember correctly, it gets that info from the registry of the installed rom, which would suggest to me the possibility of a non stock rom, something thats been messed with, you sometimes see people post odd entries after JTAGGing and the like.
What's the history of the phone? you know where it originally came from? the original carrier? has it been repaired in any shady one-man phone repair shops?
for me, id try the following,,, get a 2gb (4gb at a push, certainly no bigger) and make a goldcard (instructions here - gc creator here )
get the wwe unbranded 3.14 rom, extract the ruu_signed, rename to leoimg,,, (blah blah u know how to sd card flash)
samsamuel said:
i was assuming you'd done a task29, (i dont read back previous posts, it'd take me forever, heh, so sometimes i miss / miss-remember something)
Just had a quick 20mins reading and googling, , strange thing is, , your line "B 1.48.71294" , , , thats an odd looking rom version, it would normally be something like 1.43.206.4, , where the .206. gives the rom locale, and carrier (206 is O2 uk, for example)
71294 is (i think) a build number, something like that, but i dont remember it ever being displayed on the start screen (course its been a loong time since i booted winmo)
If i remember correctly, it gets that info from the registry of the installed rom, which would suggest to me the possibility of a non stock rom, something thats been messed with, you sometimes see people post odd entries after JTAGGing and the like.
What's the history of the phone? you know where it originally came from? the original carrier? has it been repaired in any shady one-man phone repair shops?
for me, id try the following,,, get a 2gb (4gb at a push, certainly no bigger) and make a goldcard (instructions here - gc creator here )
get the wwe unbranded 3.14 rom, extract the ruu_signed, rename to leoimg,,, (blah blah u know how to sd card flash)
Click to expand...
Click to collapse
Great info, I did suggest to the OP that he may need a goldcard but its been a long time since I have made one, hopefully he will get his phone working soon !
How task29? i don't have HSPL and you must have it do task29
My dad officaly bought it from the offical import of the phone in israel, "Newpan", with offical hebrew on it
Simfree from factory.
It was repaired by him
Clicked "'Get SD Serial and Disk ID" - the software get stucked. it's suppose to take that long?
efi2222 said:
My dad officaly bought it from the offical import of the phone in israel, "Newpan", with offical hebrew on it
Simfree from factory.
Click to expand...
Click to collapse
hmm, cant find any reference to an official (as in htc) newpan rom, just a few mentions of people installing something from the htc desire to get rtl text working, perhaps newpan cooked their own, , shouldnt matter though, at least we're sure its not a jtagged device, or a rebuild from parts.
It was repaired by him
Clicked "'Get SD Serial and Disk ID" - the software get stucked. it's suppose to take that long?
Click to expand...
Click to collapse
no, it shouldn't, what sd card reader are you using? a usb one? one in teh front of a pc? cos if they're usb mounted then you actually often get the cid of the card reader not the card, ,
In htc site you can't find roms for hd2 at all
Through my samsung i9000 because 64bit doesn't support my card reader
even though it's not connected it's stuck.
sorry, out of ideas, other than hunt out sources of card readers, , friends computers, laptops, other phones, multibooting a 32bit operating system.,,,,
samsamuel said:
sorry, out of ideas, other than hunt out sources of card readers, , friends computers, laptops, other phones, multibooting a 32bit operating system.,,,,
Click to expand...
Click to collapse
I will connect it through SD adaptor straight into a laptop
efi2222 said:
I will connect it through SD adaptor straight into a laptop
Click to expand...
Click to collapse
Same error on trying to flash hspl (other computer running win7 32bit) and also trying to make a goldcard. Revskill just get stucked
Related
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.
Hello everyone,
i've been reading this forum for one month,
It was the day I decided to upgrade my HTC HD2, and someone disconnected the usb cable during the process.
Don't talk to me about that ;-)
The problem is I can't flash any rom radio into the phone.
OS ROMS work.
I read carefully a lot of posts here, I can say I have exactly the same problems as _Juster_ from this post :
forum.xda-developers.com/showthread.php?t=618084
My phone is a french HTC HD2, Orange branded.
I successfully installed HSPL 2.08
Making upgrades using USB is very difficult, it is very unstable (communication errors, no response from the phone....) .
I tried on windows 7 pro and win xp sp3 and it is the same.
I then created a goldcard, that I'm using to flash directly in the phone. It is stable, but when flashing a radio rom I always get the "ERROR 00018003, RSA FAIL error".
I learned from xda that the issue can be solved by flashing the original stock radio rom from Orange.
I downloaded a lot of shipped roms from Orange, or HTC.
Always RSA_FAIL.
I'm maybe doing something wrong, or this is a hardware problem....
a few questions for you folks :
1/ It seems that the original Orange stock rom is a 1.43
Must I have the 1.42 HSPL to flash it ?
Is the version of your HSPL important, when you want to flash a rom ? can I flash whatever rom with any HSPL ?
2/ using a Glodcard with HSPL already installed.
when you enter on the bootloader (vol down + power) you arrive on the HSPL tri color screen, displaying HSPL 2.08....
Are you sure the Goldcard is being used ?
How to be sure of that ?
I think (I may be wrong) when you enter the bootloader mode You are on HSPL mode.
What I do to enter the goldcard mode :
I just press power,
I have a "Software update failed message"
Then I arrive to the "Loading..." message
With the name of the ROM i'm trying to flash
LEOIMG.nbh
RADIO V2
Press power to start update
Am I right ?
Thanks for reading this and helping me.
is there other Tasks like task 29 you are aware of ?
Task 29 formats the phone ?
is there a way to partition the phone or to diagnose if there's a problem ?
what do we know about that RSA_FAIL ?
I assume the RSA proccessing is to check whether the RSA Key of the radio rom matches the phone's one ?
Is there a software way to bypass that RSA check ?
I've downloaded 22 radio roms (from orange and HTC) + several others (shipped & cooked)
I always get a RSA FAIL message when I try to flash.
any clue ? something ?
Can't really make out if you tried it from your post, but you could try to flash back to stock by using the SD flash method. Just put the leoimg.nbh in the root of the SD and boot while holding the vol down button. That way you go back to stock spl, rom and radio.
Check the sticky in the ROM development section which refers to the whole HSPL and how to flash everything topic. That should fill you in on HSPL.
Robinmasters said:
what do we know about that RSA_FAIL ?
I assume the RSA proccessing is to check whether the RSA Key of the radio rom matches the phone's one ?
Is there a software way to bypass that RSA check ?
I've downloaded 22 radio roms (from orange and HTC) + several others (shipped & cooked)
I always get a RSA FAIL message when I try to flash.
any clue ? something ?
Click to expand...
Click to collapse
take a look at this thread, it might help
http://forum.xda-developers.com/showthread.php?t=621930
Thanks for the answers.
R3dox said:
Can't really make out if you tried it from your post, but you could try to flash back to stock by using the SD flash method. Just put the leoimg.nbh in the root of the SD and boot while holding the vol down button. That way you go back to stock spl, rom and radio.
Check the sticky in the ROM development section which refers to the whole HSPL and how to flash everything topic. That should fill you in on HSPL.
Click to expand...
Click to collapse
I already flashed 22 radio roms and a dozen of full roms (os + radio) using SD CARD.
As the usb is very unstable I'm using the sd card method to flash, which is also a goldcard.
the problem is I ALWAYS get the RSA FAIL message (error 00018003) at the end of the radio flashing process.
This guy : forum.xda-developers.com/showthread.php?t=618084
had the same problem but with un unbranded phone and had it solved by flashing a cooked rom he randomly choosed.
To understand the situation,
my phone is an Orange branded one, what is the difference between a branded and an unbranded phone, assuming they both have the same HSPL ?
thx
Just sold my HD2.
Seems like some questions don't have answers....
what was the problem? íf i understand you right, it even worked..but you couldnt flash another radio...
why dont you use it further?
DN41
The phone wasn't able to boot
It was stuck at the white HTC logo,
After the failure of a radio flash, I was not able to flash it again. (RSA FAIL)
I read all the posts about this problem in xda, tried everything, nothing worked.
sorry...
so who bought it? how much did you get?
someone who needed a new lcd or so?
DN41
150€ , it was in a very good condition
RSA FAIL
PROBLEM WHEN TRYING TO UNBRICK MY HD2 STUCK ON STICK TOGETHER SCREEN I GOT THE STOCK FIRMWARE FROM TMOBILE AND CHANGED NAME TO leoimg.nbh SAVE TO FORMATTED SD CARD FAT 32 AND TRY TO LOAD THIS IS THE ERROR DON'T KNOW HOW TO SAVE MY PHONE I HAVE A WINDOWS XP PC AT HOME
i've same problem, anybody know how to solve this problem?
rudon100 said:
PROBLEM WHEN TRYING TO UNBRICK MY HD2 STUCK ON STICK TOGETHER SCREEN I GOT THE STOCK FIRMWARE FROM TMOBILE AND CHANGED NAME TO leoimg.nbh SAVE TO FORMATTED SD CARD FAT 32 AND TRY TO LOAD THIS IS THE ERROR DON'T KNOW HOW TO SAVE MY PHONE I HAVE A WINDOWS XP PC AT HOME
Click to expand...
Click to collapse
You don't just rename the whole update,you extract the ruu_signed.nbh file and rename that.
RSA FAIL
I had the same problem with my polaris (htc touch cruise - pola160). I managed to get rid of the problem by downgrading the radio rom.
I couldn't find my old one, but I was able to find the highest version older than my old one in the forum. So I first downgraded the radio using the sd card, after that the rom I was trying to install in the first place worked.
Thx to pcarvalho for this "fix" : http://forum.xda-developers.com/showpost.php?p=3645124&postcount=1 - the "Important Note:" section (always read the small print ).
Hope this helpes.
PS: Sorry if this is too late for some...
having this exact same problem, radio rsa fail, can't even flash a stock rom.
did anyone solve this?
rudon100 said:
PROBLEM WHEN TRYING TO UNBRICK MY HD2 STUCK ON STICK TOGETHER SCREEN I GOT THE STOCK FIRMWARE FROM TMOBILE AND CHANGED NAME TO leoimg.nbh SAVE TO FORMATTED SD CARD FAT 32 AND TRY TO LOAD THIS IS THE ERROR DON'T KNOW HOW TO SAVE MY PHONE I HAVE A WINDOWS XP PC AT HOME
Click to expand...
Click to collapse
Fz.hary said:
i've same problem, anybody know how to solve this problem?
Click to expand...
Click to collapse
jasonlee90210 said:
having this exact same problem, radio rsa fail, can't even flash a stock rom.
did anyone solve this?
Click to expand...
Click to collapse
Put the back of the phone in front of an AC in cold for 5 minutes, and keeping it always in front of the AC try to install.
If you are able to do that, send it back to the warranty.
Hello,
I have the same problem!
long time ago I had HTC devices, but few days ago I bought HD2 and it was installed android. Is unable to start or when they try to load a ROM eror occurs.
phone has only a white scrin.
error occurs mostly when upgrade Radio ver. I somehow managed NRGZ image but again not boot system.
Task 29 also comes to 19% and stops with the error.
I have a feeling that the real problem is the radio version. (00,018,003 Radio Fail)
I do not know what is the original ROM.
IMEI: 3526 6604 8712 295
SPL 2.08.HSPL
any help came good
Hello,
at first I like to say, that I've read lots of threads concerning freezes, false flashed roms, etc. but I don't found a thread which deals with my problem. In fact of this I opended a new thread.
What is the problem?
- The HD2 hangs up with a white screen while booting.
What things are still working?
- I'm able to go into bootloader mode (Vol-Down + Power)
- I'm able to get a USB Connection through the bootloader mode
The self analyzed main problem
- I've got a broken Radio Rom
- I've got SPL 1.42 (no HSPL)
What I've tried
- I tried to flash a Rom due to CustomRUU (Cooked & Ship Rom)
-- Effect: No success. Hang's up at 0% (I think due to SPL)
- I tried to flash a ROM by SD-Card over bottloader.
-- Effect: It load's the setup. Trys to install, but fails with the Radio part. (Radio Update failed)
- I'm able to get in MTTY an do a "Task 29". And try to flash again.
-- Effect: Task 29 works well. But flashing still fails at RadioROM Update.
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.)
- I tried to get HSPL (1.42, 1.66, 2.08). I tried all versions. HSPL, HSPL2 & HSPL 3.
-- Effect: HSPL finds my HTC. I can select the version. But while flashing HSPL it stop with an critical error. (Flow: 00000006 Errorcode: 00000014)
So is there anybody how knows a way to restore my RadioROM? I tried lots of things but now I really don't know what to do.
I hope you can understand me (incause of my english skills) and that you'll have some more ideas.
With best regards,
Raffi
Lets wait for the pro's advice!
But if u can access bootloader, not all is lost.. and HD2 is not bricked
I had nearly the same Problem. The only difference was that i could install HSPL.
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
netblognet said:
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.
Click to expand...
Click to collapse
that's correct, it doesn't need to connect to wmdc, when they say to get an activesync connection, they only mean a usb connection. if you start the update whilst it IS connected to wmdc, the first thing it does is disconnect and then put the phone into bootloader. you are helping things along by entering bootloader yourself. a little confusing.
that being said, i suspect it won't work. i've seen a few threads where the radio prevents anything flashing, and they never seem to conclude to anyone's satisfaction.
i would probably go for the goldcard method, but you might need a working winmo phone to get the sd cid. an eveningsreading ahead of ya.
Esquilax said:
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
Click to expand...
Click to collapse
I'll try that. And tell you what happens.
samsamuel said:
i would probably go for the goldcard method, but you might need a working winmo phone to get the sd cid. an eveningsreading ahead of ya.
Click to expand...
Click to collapse
I really don't know, but I think I've got a goldcard. So I've 2 micro-SDs. With the first I'm unable to flash anything. The second I made goldcard some flashs ago. I really thought Goldcard would be only work for one flash. But with the second sd-card, which I made goldcard once ago, I'm able to initiate a flash. (But it stops at the Radio-Update.)
Question 1:
How to proof if it's a Goldcard.
Question 2:
I've heard about "JTAG". A saw that it's a piece of hardware. Are there any reports, at this moment, about successful repairs of HD2s with JTAG?
1 no idea, but i do know it stays gold until you format it.
2 there are a few threads about it, look in the tmous section, there are one or two in there too.
i thought it might not help.
have a browse through previous posts by xmoo, he has helped some situations regarding a stuck radio, though no promises.
netblognet said:
Hello,
at first I like to say, that I've read lots of threads concerning freezes, false flashed roms, etc. but I don't found a thread which deals with my problem. In fact of this I opended a new thread.
What is the problem?
- The HD2 hangs up with a white screen while booting.
What things are still working?
- I'm able to go into bootloader mode (Vol-Down + Power)
- I'm able to get a USB Connection through the bootloader mode
The self analyzed main problem
- I've got a broken Radio Rom
- I've got SPL 1.42 (no HSPL)
What I've tried
- I tried to flash a Rom due to CustomRUU (Cooked & Ship Rom)
-- Effect: No success. Hang's up at 0% (I think due to SPL)
- I tried to flash a ROM by SD-Card over bottloader.
-- Effect: It load's the setup. Trys to install, but fails with the Radio part. (Radio Update failed)
- I'm able to get in MTTY an do a "Task 29". And try to flash again.
-- Effect: Task 29 works well. But flashing still fails at RadioROM Update.
- I've tried to get a connection to the WMDC and try to flash over UpdateUtility
-- Effect: The WMDC doesn't recognize my HD2. (Even if the bootloader menu shows up a USB connection.)
- I tried to get HSPL (1.42, 1.66, 2.08). I tried all versions. HSPL, HSPL2 & HSPL 3.
-- Effect: HSPL finds my HTC. I can select the version. But while flashing HSPL it stop with an critical error. (Flow: 00000006 Errorcode: 00000014)
So is there anybody how knows a way to restore my RadioROM? I tried lots of things but now I really don't know what to do.
I hope you can understand me (incause of my english skills) and that you'll have some more ideas.
With best regards,
Raffi
Click to expand...
Click to collapse
Flash through usb your mama rom, I mean the rom which had the phone originally from factory.
Esquilax said:
I had nearly the same Problem. The only difference was that i could install HSPL.
Something you can try: disconnect the battery for some hours and then flash from SD-Card. After some tries i got mine back to work
Click to expand...
Click to collapse
I've tried it. No difference to before.
samsamuel said:
1 no idea, but i do know it stays gold until you format it.
Click to expand...
Click to collapse
I've formatted the card, but then there the question why I'm able to start a flash with these ex-gold-card and why I'm unable to flash with the other card. Both are 2GB and both are fresh formatted.
NIKOSXRI said:
Flash through usb your mama rom, I mean the rom which had the phone originally from factory.
Click to expand...
Click to collapse
Nice tip, but to my detriment i don't know which version exactly was the shipped one. I received one of the first HD2 in germany from tmob. I think it was something 'bout 1.43.But I really don't know. And you're sure that the original ROM will refresh the broken Radio?
is one sd card bigger than 4gb? 8 and especially 16gb cards are not much use for flashing.
netblognet said:
... Both are 2GB and both are fresh formatted...
Click to expand...
Click to collapse
Like already said, both are 2GB SD-cards.
I think the problem arised because you tried to flash a custom ROM without HSPLing (or Gold Carding or SSPLing) first.
You don't need the origional shipped ROM, all you need is to go to HTC Germany's site and download a T-Mobile ROM. You can either put your phone into Bootloader Mode, connect to your computer and run the ROM exe file or use the SD Card method.
It should flash properly and you should have the T-Mobile Germany ROM, RADIO and SPL.
In future if you want to flash a ROM, then read the chef's instructions. If you are sure you want to flash that ROM, then read the instructions again.
Nice tip, but to my detriment i don't know which version exactly was the shipped one. I received one of the first HD2 in germany from tmob. I think it was something 'bout 1.43.But I really don't know. And you're sure that the original ROM will refresh the broken Radio?
Click to expand...
Click to collapse
This is a solution for sure, I had the same problem.
Search in tmobile site or ask them for their first german rom.
Ok, I downloaded a Original Tmo-Germany ROM from HTC. But same errors. Over Update-Utility >> Error 262 at 0% after some minutes. Over SD-card: Update starts. Progressbar runs. And then >> Radio_ failed.
netblognet said:
Ok, I downloaded a Original Tmo-Germany ROM from HTC. But same errors. Over Update-Utility >> Error 262 at 0% after some minutes. Over SD-card: Update starts. Progressbar runs. And then >> Radio_ failed.
Click to expand...
Click to collapse
You must try the old-first tmo german rom that they loaded in the phone.Not just a tmo german rom!
When I had the same problem and I flashed a current rom, the problem remained until I flashed the first old rom.
Ok, I got the first and original rom. But it also fails at the Radio Update. But i found a friend of my friend who's got a HD2, too. So i'll try it with the goldcard method...
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Abdul9. said:
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Click to expand...
Click to collapse
Thanks, I will try it. This stockrom is 1.66?
zoldya said:
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Click to expand...
Click to collapse
You can also download HSPL 4 and use it to downgrade your SPL. To do this manualy put your HD2 into bootloader by holding the volume down button and pressing the power(end) butom momentarily. Once in bootloader connect your HD2 to your computer via USB cable wait until you see USB in the white bar of thd bootloader and run the HSPL 4 on your computer. It will ask you which SPL or HSPL you wish go flash select the proper SPL version to flash to your HD2 and you should be good to go. Hint the SPL version will have zeros at the end of them and the HSPL version will not. Example SPL 2.08.0000 HSPL 2.08. Hope this helps.
T-Macgnolia said:
You can also download HSPL 4 and use it to downgrade your SPL. To do this manualy put your HD2 into bootloader by holding the volume down button and pressing the power(end) butom momentarily. Once in bootloader connect your HD2 to your computer via USB cable wait until you see USB in the white bar of thd bootloader and run the HSPL 4 on your computer. It will ask you which SPL or HSPL you wish go flash select the proper SPL version to flash to your HD2 and you should be good to go. Hint the SPL version will have zeros at the end of them and the HSPL version will not. Example SPL 2.08.0000 HSPL 2.08. Hope this helps.
Click to expand...
Click to collapse
I have tried that, but after a few minutes - when it tries connect to the device - the HSPL setup writes out an error message;
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
but i don't know why, because during the installationvI see USB in the white bar of the bootloader - the device manager on the notebook shows the connection too. :S
Abdul9. said:
Very siple but you need lots of time for it. The rom you flashe has spl 3.03 on it and so it doesn't allow you to flash any other spl on it. What you can do is you have to search for old stock roms in the native language of your phone. As long as the phone keeps giving you error when trying to flash a stockrom with you sd card, it means you have not yet gotten the right stockrom for you phone so you have to try with different old stockroms till you get the right one.
After that. you'll be able to flash whatever you like. Hope it helps.
But remember, you need time and patience.
Click to expand...
Click to collapse
I just finished with the 1.66 OSPL roms http://http://forum.xda-developers.com/showthread.php?t=623283 but the problem was the same with each one. Should I try the 3.14 rom-s too?
zoldya said:
I just finished with the 1.66 OSPL roms http://http://forum.xda-developers.com/showthread.php?t=623283 but the problem was the same with each one. Should I try the 3.14 rom-s too?
Click to expand...
Click to collapse
Have you tried to restart your PC and or change another USB port of your PC?
zoldya said:
I have tried that, but after a few minutes - when it tries connect to the device - the HSPL setup writes out an error message;
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
but i don't know why, because during the installationvI see USB in the white bar of the bootloader - the device manager on the notebook shows the connection too. :S
Click to expand...
Click to collapse
Try the above post by silverwind and try another USB port, another computer, and another cable if you have too. Something just does not sound right about this. I am looking at this.
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
Click to expand...
Click to collapse
Just keep trying man I think you might just have a simple problem here.
Heck reset your notbook if you think it might help.
I have tried that too, and didn't solve the problem... :'(
Do you think that GoldCard method would help?
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Chameleon846 said:
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Click to expand...
Click to collapse
Did you place the leoimg.nbh on the root of your SD card? Also was tbe dile you renamed originaly named RUU_signed.nbh?
T-Macgnolia said:
Did you place the leoimg.nbh on the root of your SD card? Also was tbe dile you renamed originaly named RUU_signed.nbh?
Click to expand...
Click to collapse
Yes on both counts... I've even tried a complete 'long' reformat of the SD card first using the Panasonic SD Formatter, before putting the leoimg.nbh at the root.
I'm guessing that my stupid mistake is downgrading to SPL2.08.0000 whilst having a generic version of the 3.14 ROM installed. I guess I should have downgraded the ROM to an original Tmobile one first...
Could i ask what operating system you guys are using cos this problem could have less to do with the phone than it has to do with the operating system on the pc. I was trying to flash some roms on some old devices using Windows 7 but this didn't seem to work but it magically worked when i used Windows xp. I hope this works.
About the wrong Vendor problem, this just means the rom flashed is not recognized by the phone as the official one, i also had that problem and after flashing a official rom in the language of my phone, the problem was solved. I used the 1.66 rom so that i could flash hspl or else it might be impossible to do so.
Or as someone suggested you might try the hspl4 (never knew that existed) but try using Windows xp and if the problem persists try reinstalling your operating system (on your pc). I know it a lot of work but its just to rule out that the problem is from the pc.
Another thing i want to make sure of is if the phone is working normally with the rom on it or is there no rom at all?
Abdul9. said:
Could i ask what operating system you guys are using cos this problem could have less to do with the phone than it has to do with the operating system on the pc. I was trying to flash some roms on some old devices using Windows 7 but this didn't seem to work but it magically worked when i used Windows xp. I hope this works.
About the wrong Vendor problem, this just means the rom flashed is not recognized by the phone as the official one, i also had that problem and after flashing a official rom in the language of my phone, the problem was solved. I used the 1.66 rom so that i could flash hspl or else it might be impossible to do so.
Or as someone suggested you might try the hspl4 (never knew that existed) but try using Windows xp and if the problem persists try reinstalling your operating system (on your pc). I know it a lot of work but its just to rule out that the problem is from the pc.
Another thing i want to make sure of is if the phone is working normally with the rom on it or is there no rom at all?
Click to expand...
Click to collapse
Hi. Thanks for the input. The problem is getting even more frustrating! I've tried buying a new 4GB micro SD card (both are class 4). I have tried both TMO_UK_1.72 & TMO_UK_1.43. Both ROMs were downloaded from HTC using the correct phone's serial, so they should be the correct ones.
With the original SD card I can't get passed the bootloader screen & it just stays in 'serial' mode. With the new SD card it moves on to 'loading...', but then just hangs. I haven't yet seen the word 'searching' as described in the [TUT] Flash your ROM / Radio via microSD.
To clarify, the phone boots fine with the installed 3.14 ROM, but I can't get away from SPL 2.08.0000 or flash any other ROM.
Chameleon846 said:
Hi. Thanks for the input. The problem is getting even more frustrating! I've tried buying a new 4GB micro SD card (both are class 4). I have tried both TMO_UK_1.72 & TMO_UK_1.43. Both ROMs were downloaded from HTC using the correct phone's serial, so they should be the correct ones.
With the original SD card I can't get passed the bootloader screen & it just stays in 'serial' mode. With the new SD card it moves on to 'loading...', but then just hangs. I haven't yet seen the word 'searching' as described in the [TUT] Flash your ROM / Radio via microSD.
To clarify, the phone boots fine with the installed 3.14 ROM, but I can't get away from SPL 2.08.0000 or flash any other ROM.
Click to expand...
Click to collapse
Ok here is a couple of options for you. One go to www.t-mobile.com if you have a T-Mobile HD2 and type HTC HD2 upgrade in the search box on the home screen of the website and you will find the official T-Mobile 3.14 ROM. You will have to enter your IMEI number under your battery to download it. Download this ROM and then follow the steps to flash it via SD card, hint you will have to rename the original .exe file to .zip to gain access to the .nbh file. Also you can download and run HSPL 4 on your HD2 and select SPL 3.03.0000 but the official ROM will change it to SPL 3.10.0000 if you flash via SD card
Its a common problem i think if you are trying to flash a rom via sd card with a sd card higher than class two. Many here have encountered such problems.
According to your description, it will seem that it is as i suspected, the pc doesn't seem to recognize the phone and this could mean you have a defect usb cable or the useport itself is not funtioning properly. Try holding the phone in your hand with the usb in and support the usb with your hand to make sure the usb is indeed in the phone and see what happens. My usb cable is a little bit loose so when i want to flash anything, i use my hand to support it or i place my phone on a smoot surface and make sure the usb cable is in it.
zoldya said:
Hy!
I did a stupid thing, with the following. I copyed an LEOIMG.nbh file to my formatted sd card, so I get an SPL-1.42.0000, but I can't flash any HSPL to my device, because the HSPL setup writes out USB connection error. Neighter can I flash for example the official 1.66 rom, the installation stops after 1%, and writes INVALID VENDER ID. What can I do?
Click to expand...
Click to collapse
Chameleon846 said:
Hi. I have the same pronblem. I have a UK HD2 that was originally on Tmobile. I flashed 2.08HSPL using HSPL4 & upgraded the ROM to the standard WWE_3.14. A long story short... after playing around with SD Android & a few other utilities I wanted to make a clean start, so my plan was to use HSPL4 to remove the HSPL before then re-installing it & reflashing the ROM. Unfortunately I now seem to be stuck in SPL2.08.0000. HSPL4 just gives the same error:
CRITICAL ERROR
Flow:00000001
Error code: 00000002
Description: USB Connect failed!
I have also tried flashing a stock ROM via SD (renamed leoimg.nbh), but I can't get passed the bootloader displaying 'serial'.
Any ideas?
Click to expand...
Click to collapse
Ok do to some recent personal experience and some other members problem of late. I suggest both of you do this go to www.windowsmobile.com/getstarted and download the most recent version of WMDC wich has updated drivers in it that seems to solve somd problems with flashing via USB especially if you are using a 64 bit system. Just so both of you know unless your HD2 shows up as "HTC USB Sync" in the device manager while connected via USB while in bootlaoder you do not have the correct drivers installed and any flash will fail.
T-Macgnolia & Abdul9: Thanks for that, however mine is a UK Tmobile HD2 & the .com site is only for US ones (it doesn't recognise UK IMEI's). If I go via the UK site it just links me to the HTC update site for the RUU_Leo_S_TMO_UK_3.14.110.1_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship (& also the 1.72 & 1.43 versions. I have tried all of these via both SD card & via USB. I have also tried HSPL4, HSPL3 & HSPL2. All options have failed. I have tried from Win XP Pro & Win 7 Ultimate (both 32bit) with two different USB leads. I have also tried a 3rd SD card (which ends up stalling at the 'loading' screen. The phone flashed fine prior to removing 2.08HSPL with HSPL4.
I think that the problem is not the SD card or the USB lead, but is the problem that I've now got a Tmobile (UK) phone with spl 2.08 & a WWE_3.14 ROM installed - this should obviously not normally be possible. I can't flash back to HSPL & I can't downgrade to any other ROM.
Does anyone have any idea how I can 'fool' the phone into letting me change the ROM?
I've been reading about Task29, but it says don't do this unless you have HSPL (which I can't get!). I don't want to brick the phone (because it still runs!), but I want HSPL back otherwise I can't reinstall Android on SD.
Furthermore, I don't think this is a USB driver issue, as it flashed fine before & it's occurring across different PC's & operating systems.
It's an incompatibility between a branded Tmobile with SPL & a WWE HTC ROM... I just need to get out of the loop I'm stuck in!
Hey Chameleon I know you don't think it is a problem with the drivers cause it was flashing fine before. But what I do not think you have taken into account is that you came from a older ROM and you had the right drivers to work with that ROM or the update for that ROM. But you now have a 3.14 ROM and this is a newer ROM that probably requires different drivers. I mean Microsoft did not create a new WMDC with updated drivers if it was not needed for the 3.14 ROMs as they are the most recent official ROM versions. Microsoft is the one that comes out with the new ROM versions too, the carriers just add their bloatware to them. Do you see my train of thought here? Also make sure you are usinv SD card that is 500MBPS to 8GB that is formated with Fat 32.
T-Macgnolia said:
Hey Chameleon I know you don't think it is a problem with the drivers cause it was flashing fine before. But what I do not think you have taken into account is that you came from a older ROM and you had the right drivers to work with that ROM or the update for that ROM. But you now have a 3.14 ROM and this is a newer ROM that probably requires different drivers. I mean Microsoft did not create a new WMDC with updated drivers if it was not needed for the 3.14 ROMs as they are the most recent official ROM versions. Microsoft is the one that comes out with the new ROM versions too, the carriers just add their bloatware to them. Do you see my train of thought here? Also make sure you are usinv SD card that is 500MBPS to 8GB that is formated with Fat 32.
Click to expand...
Click to collapse
WOW! I've got the problem sorted! This can't be a coincidence... I haven't done anything different to my PC, but I got an 'unlock' code through for my phone this morning (£5.99 on Ebay) & it worked fine. I though "why not" & tried HSPL4 again. With no other changes it worked absolutely fine this time & I now have 2.08HSPL installed.
Presumably by unlocking my my phone from Tmobile it has also removed the 'you're using the incorrect ROM' problem.
Thanks for everyones input on this. I maintain that XDA-Developers is one of the best Forums around (not just within the mobile phone arena).
Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
I had to flash SPL via Y-cable per Cotulla's instructions in the HSPL Thread. But you may not need to let it sit overnight, I don't know. Maybe you can flash right away and get back to 1.10 or maybe not. It was just an unplanned event that had a brilliant result.
I hope it works for you too.
nikola92 said:
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
Click to expand...
Click to collapse
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
nikola92 said:
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
Click to expand...
Click to collapse
Please check out my post under debrand instructions under Windows Phone 7 development; you do not need your SPL to read 1.09 or 1.10 to successfully HSPL; it is imperative with whichever ROM you use for your device to read "HTC Titan x310e" not "HTC Titan P139100" following that first flash via Gold Card or everything that follows is mute. It is the 2nd step that will test your patience if you find yourself staring at "Entering USB Host Mode..." If following your flash of SPL205's NBH file you do not read on that screen, "Radio - OK", "Bootloader - OK", "Update Successful, UPDATE COMPLETED" your device will not HSPL on the next step. I recommend from the very beginning you rename the .NBH files to ETERDIAG (8 characters; no more) for steps 1 and 2 flashing via Gold Card. When you make your Gold Card use Quick Format; do not re-format your card following step 1; it is not necessary. I do recommend prior to copying the respective .NBH files to your Gold Card that they are renamed prior to copy. One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
berrywr said:
One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
Click to expand...
Click to collapse
This exactly. I was able to make calls and use the device as intended. Not like I wanted, but definitely as intended.
I was wanting to get back to stock SPL because I thought it was the only way to flash. The Titan forums are full of people that have been unable to attain HSPL due to the idea of being stuck on 2.5 bootloader was the cause. If your method works, that's awesome. As I said in my post, maybe it was a fluke but it seems so much easier to flash from stock. My primary device now is a One X so I may do some tinkering with my Titan soon. Regardless of how it turns out I appreciate your input into this.
R
But the now i when i write ETERDIAG i get flasing progres to start it comes nearly to end and then i get error 39 update terminated
Please Mr. berrywr Can help me ?
Pardon my English i'm an Italian Titan owner
I try your Plan B to debrand and have HSPL on my device because it doesn't go on using ETERIMG
I go on with ETERDIAG and everythings go in right way but ..
when i try to flash the renamed ETERDIAG.nbh copied from “SPL205” folder
my device don't FREEZE to Entering USB Host Mode but return on bootloader screen
i try after 15 or 20 minutes to move pointer with volume button and i'ts died no moove nothing change
only when i disconnect usb cable it's possible to move pointer up the bootloader menù
Now i try to change rom .
i start with european rom IMG_Eternity_HTC_Europe_1.09.401.02_Radio_16.23.02.09_A_16.24.00.23_Signed_ETERNITY_RELEASE
and i want follow your help and try with IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE.nbh.
hope to read HSPL on my device please if someone have same problem PLEASE help me go on with my job
i write back if everythings go ok wih cingular rom but .. ok i write back
Best Regards Fabio Ducilli form Italy
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
silentP said:
Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
Click to expand...
Click to collapse
It did not work for my titan...
ppgame said:
It did not work for my titan...
Click to expand...
Click to collapse
Sorry to hear that my friend. However, berrywr has been giving some excellent tuts for flashing. Thanks for giving it a shot though.
Specification of proble titan 1 hspl
berrywr said:
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
Click to expand...
Click to collapse
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
wileharley said:
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
Click to expand...
Click to collapse
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
nikola92 said:
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
Click to expand...
Click to collapse
I restarted my device in Bootloader Mode; it reads as follows:
1st line: PI39100 - That's Papa India Three Nine One Zero Zero
2nd line: HSPL2.5.160015.3(137079)
3rd line: eMMC SND 15188MB
4th line: CotullaH(F:81, ID:1, V11,B:F8)
5th line: "Double Space"
6th line: Radio-17.5006.08.27 (This is the required radio for the Eburon WP7.8.8858 custom ROM).
In regards to your device reading x310e; that's good news! You're half way there. You need to have a successful second flash with your gold card with SPL205. Your device will automatically restart and return to Entering USB Host Mode prompt...it is this step you must have patience; it has to read Radio - OK, Bootloader - OK...Update Successful, UPDATE COMPLETED; it cannot be anything else or any combination other than these four.
Upon completion of the 2nd flash...SPL205's nbh file does your display indicate both Radio-OK and Bootloader-OK, Update Successful, UPDATE COMPLETED?
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
nikola92 said:
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
Click to expand...
Click to collapse
If what you've written is correct then you are two-thirds the way there and what's left to do is connecting your device to your computer with Zune running, Your device is to be in bootloader mode when you do this, look for USB at the bottom and execute the program by right clicking the application and run it as administrator.
I did that, proces said finished and boom no hspl cotula writing......
Same problem with HSPL for me
[/COLOR]
berrywr said:
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
Click to expand...
Click to collapse
i do the same :
ok flash the european rom using ETERDIAG .. ALL OK
ok flash spl 2.05 and everything ok Radio etc with ETERDIAG MODE ALL OK
ok install as adminitrator DFT__HSPL_WP7SG1 and ALL OK
but when i restart it can't find cotulla inside my bootloader
i'm happy because my original rom was only english and now i have european rom but
i need unlock it with HSPL .. grrr
---------- Post added at 06:38 PM ---------- Previous post was at 06:00 PM ----------
06.57 PM 01/01/2013 just finish to RETRY all .... nothing good only my italian rom
not work for me too
No good news
No work for me too