Related
Hi! Running into some trouble. I would have posted this in the development area but I am not allowed to until I have 10 posts. I went through the process of unlocking then rooting using amon ra, but thats the last thing I did right. I was in recovery and made the mistake of thinking I could restore an old nandriod, which happened to be from my bionic. Well now I am stuck at the HTC white screen and cannot get anywhere. I downloaded the all on one kit and successfully booted into recovery using it, but even after doing a full wipe I cannot get anywhere. I am new to HTC and with a moto device I would have just sbf'd back but I dont know what to do at this point. Any and all help would be appreciated, thanks!
What did you try to restore and dis you install re install the kernel for it
sent from ics land
I tried to restore a nandroid backup which is what I am guess caused the issue. I am new to HTC and its process, so I am unaware what you are asking by kernal. I unlocked the phone and installed amon ra 3.14 and that was it. Once it was installed I went into recovery and tried the backup, which I am now regretting. Sorry, completely new to this process, thank you very much for your patients
Just download a new ROM in the development thread.
Okay, thought that may fix so I have been downloading one, just hasnt finished yet. Once completed, do I just move it to my SD card, pop it into my phone, boot into recovery and load the zip? Never done it before, just want to fact check.
Is it an ICS or GB ROM?
It is one of the ICS roms....sigh, lol, guess that complicates things. Well, since I have already gone this far, should I go ahead and just relock, load new leaked RUU then unlock and load ICS rom OR forget that, download a GB rom and just flash it?
No you're good with downloading an ICS ROM. Did you also download the PH98IMG that goes with it?
I downloaded earlier when trying to root with Amon Ra and and got a message that it was out of date, so I thought it PH98IMG was Amon Ra from what I read in the forums and downloaded the new 3.14 and loaded that. Was I mistaken? If so, what is PH98IMG? There is a wealth of knowledge on this site, just really hard to piece it all together, lol, thank you again for your patience.
I was confused at first on what it was, too. I may not be 100% on this but it's essentially the kernel for the ROM. Since we don't have s-off we have to manually flash kernels in HBOOT instead of just flashing them in recovery.
What you wanna do is rename whatever the kernel is to just PH98IMG(it usually has it already in the name). Delete whatever comes after it. So it will say PH98IMG.zip afterwards. Then what you'll wanna do is put it in the root of your sd card. That means don't place it in any folder.
Flash the ROM first in recovery then go into HBOOT and it will read the PH98IMG.zip and prompt whether you want to update or not. Hit volume UP to update and then reboot and you should be good.
Also, make sure you delete the PH98IMG.zip from your SD card before going back into HBOOT again because it will keep asking you if you want to update it. This will prevent you from getting into Recovery from the Bootloader and if you ever get stuck in a bootloop, like you just did. The only way to get back into recovery would be to remove SD card and connect it to another phone or Computer and delete it that way.
Woah, excellent, just want I needed, some simple breakdown of everything. Once last favor, I searched for the PH98IMG(cant remember where i got it earlier) and there are alot of items named the same thing. Can you point me in the right direction of the one I need?
Which ROM are you trying to flash?
CleanRom 4.0
Well, actually you will need to relock and download the RUU if you want to use that ROM.
ok, downloading the RUU now and have the Rom downloading as well, once they are finished I would relock, load the RUU, unlock then load the new Rom right?
Yes that is it. While running the RUU follow the directions from Scott to the T. He has them posted in the first post, or at least a link to his directions.
Hi everyone, so this is my first post here so please deal with me. I did check for similar problems with no results and think I'm posting in the right area. So try not to get too frustrated with me if I'm wrong. Anyway, with all of that out of the way on to my problem.
I have a rooted rezound, which was first rooted to get rid of bloatware and such, but I decided I wanted to try out some different roms. My problem is every time I flash a rom, which appears successful, but whenever it boots up it'll freeze up on the HTC screen. To fix this I've been just been pulling the battery and restoring to the backup I made before trying to flash roms. I would really like to try some different roms but I've gotten stuck on that screen with each one I've tried. If anyone could help me I'd greatly appreciate it!
Some additional info: I use to have a rooted thunderbolt and have some experience with flashing roms and all that stuff, but I'd still consider myself a noob. I have Amon Ra Recovery on my rezound and the screen in hboot reads:
***Unlocked***
vigor put ship s-on rl
HBOOT-2.11.0000
eMMC-boot
Oct 6 2011, 15:43:22
(I'm not sure why it says the incorrect date and time?)
I've tried several different things to successfully flash roms. I've tried flashing them with and without PH98IMG.zip on the root of my sd. I've tired it with and without the back on my phone. When flashing roms I ALWAYS wiped all data before flashing. That's just about everything relevant I can think of, sorry for the length! I figured the more information the easier for you guys to help!
If you're S-ON, you need to flash the P98IMG zip with the ROM. This contains the boot.img file.
Just extract the ROM of choice, take the P98IMG zip, throw it on your SD card and boot into your bootloader. Go into the bootloader menu and it'll install. Reboot, phone will work just fine.
If there isn't a P98IMG file and just a boot.img file, just push it through ADB while in your fastboot.
command is fastboot flash boot boot.img
So the P98IMG.zip file I downloaded and had on the root of my sd card is different than the one I need to extract from the rom or was I just not installing it right?
I did have a P98IMG.zip on the root of my sd card and I went into hboot, then I went to recovery and flashed my rom. Is there another step I need to take in installing the P98IMG.zip or should it automatically install? Do I need to reboot it between installing the P98IMG.zip and the rom?
Thanks for you help and quick response! I'm really trying to learn and get better at this stuff
After you flash your ROM, go into your bootloader (fully, must be in the bootloader menu) and it'll install. Follow the onscreen instructions, reboot, and remove the zip from your SD card.
Hope that helps.
I still cant get it to work :/
Heres step by step what I did:
1) Went into hboot > recovery
2) Wiped all data
3) Flashed ROM
4) Powered off phone using option in the recovery menu
5) Powered back on into hboot. The green text appeared that said loading and stuff about P98IMG and a blue bar on the side, but this process was very brief (maybe 2 seconds tops) and there were no instructions to follow
6) Went into recovery and rebooted my phone where I was stuck on the the HTC screen again
Can you point out where I'm going wrong or any possible issue?
Thanks again for you patience! I really appreciate your help!
ewy87 said:
I still cant get it to work :/
Heres step by step what I did:
1) Went into hboot > recovery
2) Wiped all data
3) Flashed ROM
4) Powered off phone using option in the recovery menu
5) Powered back on into hboot. The green text appeared that said loading and stuff about P98IMG and a blue bar on the side, but this process was very brief (maybe 2 seconds tops) and there were no instructions to follow
6) Went into recovery and rebooted my phone where I was stuck on the the HTC screen again
Can you point out where I'm going wrong or any possible issue?
Thanks again for you patience! I really appreciate your help!
Click to expand...
Click to collapse
How are you getting to recovery? It should give you an option to install update or reboot in hboot. If the ph98img is in the right spot you shouldn't be able to boot into recovery
With my phone powered off I'm holding down the power button and down volume button to get to hboot. I have my ROM and the PH98IMG.zip file both on the root of my SD card. It does very quickly appear to load the PH98IMG file but returns to the hboot screen the has the options: fastboot, recovery, factory reset, clear storage, sim lock, image crc.
Could it be that the PH98IMG file should be somewhere else? And was I doing everything in the correct order or do I install the PH98IMG first?
File may be bad. Do you have adb set up?
Sent from my ADR6425LVW using Tapatalk 2
Well actually I'm running off a mac and I've been using my sisters laptop for adb and that stuff but she just broke it...just my luck haha. Would I be able to download a different copy of PH98IMG from online and try that?
What ph file are you trying to flash? It should load it and ask if you want to update. Try downloading it again. May be a bad download
I'm trying to flash the Senseless-4.0.3-ICS-v1.0.0[2/4/2012] ROM (http://themikmik.com/showthread.php?11238-Senseless-4-0-3-ICS-v1-0-0-2-4-2012&p=178493#post178493) and I just saw a download for the PH98IMG file somewhere else on the website. Should the ROM include its own PH98IMG file? Thanks for both of your help! I have no experience with the PH files because my thunderbolt was s-off so i never dealt with this stuff before.
ewy87 said:
I'm trying to flash the Senseless-4.0.3-ICS-v1.0.0[2/4/2012] ROM (http://themikmik.com/showthread.php?11238-Senseless-4-0-3-ICS-v1-0-0-2-4-2012&p=178493#post178493) and I just saw a download for the PH98IMG file somewhere else on the website. Should the ROM include its own PH98IMG file? Thanks for both of your help! I have no experience with the PH files because my thunderbolt was s-off so i never dealt with this stuff before.
Click to expand...
Click to collapse
So s-off. Seriously though. You flashed a random ph file and thought it would work? It has to be the right one for the rom. Besides that rom isn't maintained anymore
The only method to get the rezound to s-off was using some wire trick and seemed like a difficult process. Would you recommend I do that?
And the post with the ROM said and ICS PH file would be fine, so I assumed it'd work. I guess I'll try a different ROM that includes a specific PH file and up to date. In which case I should be able to get everything to work with all the help from you and Chyrux. Thanks for everything!
ewy87 said:
The only method to get the rezound to s-off was using some wire trick and seemed like a difficult process. Would you recommend I do that?
And the post with the ROM said and ICS PH file would be fine, so I assumed it'd work. I guess I'll try a different ROM that includes a specific PH file and up to date. In which case I should be able to get everything to work with all the help from you and Chyrux. Thanks for everything!
Click to expand...
Click to collapse
I would recommend getting s-off. It's going to be the only method for this phone. I mean why waste another exploit to be patched? I would recommend con rom since it uses aroma to detect whether your s-on or s-off
Did you s-off your rezound? How were your experiences with it? I'm just worried about bricking my phone. But thanks for the ROM recommendation! I've been trying to find a good ROM
S-off was fairly easy, but you do need Windows or a Linux build.
Okay, I'm pretty sure that the guys at the other forum site gave up on me. Starting to think that I'm stuck with a paperweight that illuminates a white HTC Screen. I've searched every forum and have had no luck, but here goes:
- I'm on day four of intense troubleshooting. Apparently I'm the only person to ever root a HTC Rezound and then flash a new rom using Rom Manager (first mistake).
-I flashed a new ICS Rom using Rom Manager. I did do a backup using Rom Manager and wiped all of the caches before doing the flash. There was no problem with the install, but once I rebooted, the HTC Screen was my only accomplishment. In addition to that, the CWM Recovery Tool did NOTHING.
After reading and reading, I finally realized that only idiots like myself would still be using Rom Manager over Aman-Ra. Therefore, I installed Aman-Ra via fastboot and flashed a few other roms trying to get past the HTC screen... All of this was without any success.
I was told in a forum by someone much smarter than myself that "the easiest way back to a working phone would be to simply install a new rom like: [ROM 7/11 CONROMV5][4.0.3OTA Sense3.6+DeSense][DeBloated Root Aroma Tweaks][CDMA/GSM]." I was next told that "Conrom will deposit the PH98IMG.zip file on the sd card." This never happened.
SO, Here's where I'm ending up:
It does not boot me into Fastboot after ROM install. Instead, It gives me a "Next" button at the bottom with a log that states:
--
-Checking Model ID
-Success!
Model ID - HTC Rezound (Vigor)
-Ok to proceed
Welcome to CONROM V4!!
Installing...
Sense Selected
Sense Extracted
Face Unlock REMOVE Selected
Face Unlock NOT Extracted
Beginning Experimental Security Identification
read_file() loading "/tmp/initrd.img" failed: No such file or directory
When I click "Next" I get another screen that says:
"Congratulations... CON ROM 4.0 has been installed successfully. Press Finish, and reboot your phone. If S-ON was detected, please reboot to bootloader to flash the boot image. Thanks.
It then goes into the regular reboot process. I do a battery pull, press power+vol down and go back into HBOOT, it runs through it's IMG Check and there's nothing there. I then created a PH98IMG.zip file from the boot image inside the rom's zipped folder. Tried flashing that, and I'm still looking at the HTC Screen.
I've gotten myself into tight jams before, but been able to figure it out... I'm just at the end of my rope here. Someone with more intelligence than myself please tell me what to do to get past this and I promise to never assume that flashing a rom to a Rezound is as easy as it was with my Thunderbolt.
Thanks to whomever takes pitty on me, in advance. (seriously, Thank you)
Start over with a stock RUU zip, renamed to PH98IMG.ZIP. Put it on the SD Card. let er run?
You say you can get to HBOOT?
the only thing that generally fixes huge problems like these are to run the FULL RUU (AKA pull a complete stock rom and rename it PH98IMG.zip, enter HBOOT and let it run TWICE!!) and let it reinstall EVERYTHING (including the radios and such.) Then go into the stock recovery, do a full restore.
Then unlock your boot loader and install Amon-Ra, root and flash a rom correctly
{Full RUU here http://www.androidpolice.com/2012/0...id-4-0-build-3-11-605-22-for-the-htc-rezound/
^ I don't think it is the most recent version, but it should do as long as it is GREATER than the leak you are already on}
Don't try this solution until someone else gives a thumbs up... I don't want to be the one who causes more harm to your phone hahahaha
EDIT: Changed it to PH98IMG, my bad! Should have proof read my post one more time.. Thanks Paulhoop for catching that!
Well he was more complete in his intstructions, but we are recommending the same thing.
However, just want to correct the typo above. PH98IMG... Not PH89IMG
Also not sure about the stock recovery, full restore. But I would let the stock RUU setup run once before going to AmonRa
brandononeal00 said:
Okay, I'm pretty sure that the guys at the other forum site gave up on me. Starting to think that I'm stuck with a paperweight that illuminates a white HTC Screen. I've searched every forum and have had no luck, but here goes:
- I'm on day four of intense troubleshooting. Apparently I'm the only person to ever root a HTC Rezound and then flash a new rom using Rom Manager (first mistake).
-I flashed a new ICS Rom using Rom Manager. I did do a backup using Rom Manager and wiped all of the caches before doing the flash. There was no problem with the install, but once I rebooted, the HTC Screen was my only accomplishment. In addition to that, the CWM Recovery Tool did NOTHING.
After reading and reading, I finally realized that only idiots like myself would still be using Rom Manager over Aman-Ra. Therefore, I installed Aman-Ra via fastboot and flashed a few other roms trying to get past the HTC screen... All of this was without any success.
I was told in a forum by someone much smarter than myself that "the easiest way back to a working phone would be to simply install a new rom like: [ROM 7/11 CONROMV5][4.0.3OTA Sense3.6+DeSense][DeBloated Root Aroma Tweaks][CDMA/GSM]." I was next told that "Conrom will deposit the PH98IMG.zip file on the sd card." This never happened.
.
Thanks to whomever takes pitty on me, in advance. (seriously, Thank you)
Click to expand...
Click to collapse
You have to lock the bootloader first if you want to run the RUU.
First off...you said s-on..
Do you now what firmware you are on? Ginberbread or ICS? If you are on GB you should have installed a SD Card patch as part of your ROM flashing process. If you didn't, that is part of your problem. What happens when you try to flash the boot.img? Do you do it through fastboot? or PH98img file? It sounds like the boot.img is not flashed correctly.
topgun1953 said:
You have to lock the bootloader first if you want to run the RUU.
First off...you said s-on..
Do you now what firmware you are on? Ginberbread or ICS? If you are on GB you should have installed a SD Card patch as part of your ROM flashing process. If you didn't, that is part of your problem. What happens when you try to flash the boot.img? Do you do it through fastboot? or PH98img file? It sounds like the boot.img is not flashed correctly.
Click to expand...
Click to collapse
Ok. First off, wow, what an awesome response. I had rooted the phone through fastboot, but was still on the stock GB. I didn't know about the SD Card Patch. When I try to flash the boot.img, I did that by extracting the boot.img from the rom folder, renaming to PH98.img, and running that through the HBOOT Process (I didn't try it with fastboot). The file would update, begin the "parsing' process, and then stop and go back to the basic HBOOT screen. What would be the correct way to flash the boot.img file? What patch should I have installed relating to the SD Card, and is it too late for that?
brandononeal00 said:
Ok. First off, wow, what an awesome response. I had rooted the phone through fastboot, but was still on the stock GB. I didn't know about the SD Card Patch. When I try to flash the boot.img, I did that by extracting the boot.img from the rom folder, renaming to PH98.img, and running that through the HBOOT Process (I didn't try it with fastboot). The file would update, begin the "parsing' process, and then stop and go back to the basic HBOOT screen. What would be the correct way to flash the boot.img file? What patch should I have installed relating to the SD Card, and is it too late for that?
Click to expand...
Click to collapse
The boot file should be named ph98img.zip CHECK your named file (PH98.img???), the computer should put the .zip on it. Just be sure its not named ph93img.zip.zip!
The other way, if you're comfy with fastboot commands is to put the boot.img in the same directory as fastboot and type "fastboot boot boot.img" . No its not too late to do the SD Card Patch. You can get it here (among other places), I believe its the 'Old Firmware patch" http://www.androidfilehost.com/main/-Support_Files-/SuperChilPil/ . JUst flash in recovery.
The info for your ROM says that the installer would identify the need for the SD card patch, so maybe it did install it? Won't hurt to do it yourself though. Did you consider a more 'basic' ICS rom, like CLeanRom4.5 or the new rooted 3.14.605.12 one?
I'm on Newt's One xXx, ICS sense 4 rom myself.
I am trying to get ICS on my Amaze. I am with Telus and have an S-On phone
I am trying to use this method
Originally Posted by superevilllama View Post
flash stock recovery
relock phone (fastboot oem lock)
flash rom update in bootloader (rename ruu to ph85img.zip, place on sd card and boot to bootloader)
unlock with htc tool
flash custom recovery
flash superuser package
done!
Click to expand...
Click to collapse
But i do not have the stock recovery and unsure how to get it.
I tried skipping the step and just going from re-locking phone to updating from bootloader but I get a CID incorrect error.
Any help is appreciated, I have never had so much trouble updating a ROM
PS.
I wasn't aware so much was needed to upgrade from my BulletProof ROM to this ROM, I just flashed like I would have before and now I am in an HTC Boot loop
dibarreir said:
I am trying to get ICS on my Amaze. I am with Telus and have an S-On phone
I am trying to use this method
But i do not have the stock recovery and unsure how to get it.
I tried skipping the step and just going from re-locking phone to updating from bootloader but I get a CID incorrect error.
Any help is appreciated, I have never had so much trouble updating a ROM
PS.
I wasn't aware so much was needed to upgrade from my BulletProof ROM to this ROM, I just flashed like I would have before and now I am in an HTC Boot loop
Click to expand...
Click to collapse
It's right in the stickies man...
http://forum.xda-developers.com/showthread.php?t=1575550
Sent from my
NRGized amaze
powered by Faux
I went through that, but the RUU is an exe, or do I rename the OTA zip file to PH85IMG.
When I went through this process it loaded PH85IMG, did the check and then nothing. Never asked me to update or anything. I wouldn't have posted to ask for help if I didn't need it.
dibarreir said:
I went through that, but the RUU is an exe, or do I rename the OTA zip file to PH85IMG.
When I went through this process it loaded PH85IMG, did the check and then nothing. Never asked me to update or anything. I wouldn't have posted to ask for help if I didn't need it.
Click to expand...
Click to collapse
No. Connect your phone and flash the EXE. PH85IMG is ONLY for T-Mobile Users. Everyone else uses an EXE.
LMAO some things never change
Good luck with ICS
Sent from my SGH-T999 using Tapatalk 2
Thanks for your help! I have never felt like such a noob....I swear I am actually good with tech lol
So I managed to get my phone flashed, thanks for all of your help, but I thought the flash was suppose to upgrade me to ICS, but it installed a stock 2.3.4 I am so confused. After flashing the EXE am I suppose to use the OTA.zip? If so, from what I am reading I need to S-OFF.
I tried installing CM9 after the flash and I am able to boot, but once its loads and begins the initial setup it freezes on the Select Language screen and reboots. I have searched the forum and no luck.
Ok, I will try to give as much info as I can, please let me know if there is anything else I should provide. I really appreciate any help and advice as I've been pulling my hair out for the last 3 days, spending 10+ hours trying to get my Amaze back working.
Problem started a few days ago, phone shut off, when it powered back on it was stuck on the White HTC logo. That same day the phone died completely and would not power on at all, not even the amber light. Eventually the amber light would blink the but phone wouldn't charge. I fixed this first issue by jump starting the battery with a 9V battery, something someone suggested on a thread. Worked great to get the phone charging again... but that's it. So basically I have access to the HBOOT/Fastboot and EXT4 Recovery menu's, and there is no OS on the phone, I know for sure now because I wiped the system.
When I try (but fail) to install the RUU 1.41 exe, and it checks the phone, i comes back saying my "current" version on the phone is 2.14.661.2 even though there isn't any OS on there...
Bit more background info. I purchased this phone last year off someone, it was running 4.1.2 and the bootloader was unlocked. It *is S-ON though.
Whatever else this guy did, I'm not sure as this is what I can tell, however the CID pulls up as Telus001? which the guy did tell me it was a Telus phone.
So I'm trying to load the Telus stock rom and I've been getting nowhere and pulling my hair out. I'm 10hrs in and no further then I was. So first I downloaded the Telus RUU 1.41 exe from the stock rom but it gives an Error 43. I tried this with both the bootloader locked again, and unlocked. I then downloaded the OTA 2.14.661 zip from the stock roms, and renamed it to PH85IMG, stuck that on the Ext SD card. Problem is when it boots into the HBOOT it actually see's the file, loads it, then checks it, but then returns me to the main menu. I don't get promted to update. Now I've tried this too with the bootloader unlocked, and locked. So a third go, I extracted the Rom from the 1.41 RUU and made that PH85IMG, tossed it onto the SD card and again this time it actually went further but gave another error.
I have tried to Sideload the above Roms through recovery but they give error's.
In that All In One program there is an option to fix the Mainver error, however when I run that all I get is "Device not found". The phone IS loaded under device manager as HTC Phone as I had installed the drivers. I've tried to google this fix but I can't get anywhere.
Everyone has said on forums that sticking a PH85IMG.zip file on an Ex SD and having it boot into the HBOOT menu will rebuild the phone, but I'm out of idea's how to get there because it loads the rom's, checks them, and then boots me back to the menu. There is only 2 Rom's I can find for Telus, and that's the 1.41 EXE or the OTA 2.14.661.2. My HBOOT version is 1.93.0002, RUBY PVT SHIP S-ON RL.
Thanks in advance for any help/suggestions, desperately just want my phone working again. I feel like I've been to the 4 corner's of google trying to solve this problem.
Strange This should not happen.Also if your phone is running 4.1.2 which should be a custom then that means your phone was updated to ics so the ruu.exe will fail.if you have access to 4ext recovery then you can flash any custom rom to boot your phone.But if you want stock and both of the stock roms for your carrier is not working then the only thing you can do is s-off the phone then use supercid so you can flash any carrier's rom then flash t-mobile ics stock.Tell me if this worked for you.
darkshadow1997 said:
Strange This should not happen.Also if your phone is running 4.1.2 which should be a custom then that means your phone was updated to ics so the ruu.exe will fail.if you have access to 4ext recovery then you can flash any custom rom to boot your phone.But if you want stock and both of the stock roms for your carrier is not working then the only thing you can do is s-off the phone then use supercid so you can flash any carrier's rom then flash t-mobile ics stock.Tell me if this worked for you.
Click to expand...
Click to collapse
Got it going!! Thanks for the suggestions. What did it in the end was this thread --> http://forum.xda-developers.com/showpost.php?p=27058110
I had EXT4 Recovery already, so I used his Zip and just flashed that. Phone came back up and is running great now... if only I had found his thread before the hr's and hr's I've been googling and trying things.