Related
Hi all,
Firstly, I apologise if this is the wrong forum to post this question but with so many forums it's very hard to know which is the right one! I hope I've found it.
I've been reading around and researched how to root my Galaxy S II. In the Phone --> About my phone is 2.6.35.7-I9100 BVKG3-CL344296 so I downloaded CF-Root-SGS2_XX_OXA_KG3-v4.1-CWM4.zip which appears to be the right kernel for what I'm doing. I've downloaded Odin v1.85 and launched the phone in download mode.
All seemed to be going well and Odin saw the phone. I put the above file in the PDA section and left all the check boxes alone. I pressed Start and the little green bar got bigger with 'KERNEL' in the text box above. I got the following in the message area:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
The phone rebooted and now it is stuck on the very first screen with the yellow warning sign. I have tried to put the stock kernel back on, Kernel_I9100BVKG3.TAR, but it makes no difference. The phone is currently bricked.
Can anyone help?
Cheers,
Richard.
Did you put the .ZIP file into the PDA section?
You have to extract the .ZIP, so you get a .tar file, it's that .tar file you need to put into the PDA section.
Put your phone into download mode and try flashing said .tar file with Odin again.
Thanks for the reply, HellcatDroid.
I actually managed to figure out what was going on following that post. I had a sneaking suspicion that the USB ports on my computer weren't acting right so I tried flashing the phone again on one of my laptops and it worked straight away.
Just goes to show that you can research all the likely causes and outcomes and ultimately find out that it's something that you really wouldn't expect normally.
I appreciate your offer of help, though.
horsemanuk said:
Hi all,
Firstly, I apologise if this is the wrong forum to post this question but with so many forums it's very hard to know which is the right one! I hope I've found it.
I've been reading around and researched how to root my Galaxy S II. In the Phone --> About my phone is 2.6.35.7-I9100 BVKG3-CL344296 so I downloaded CF-Root-SGS2_XX_OXA_KG3-v4.1-CWM4.zip which appears to be the right kernel for what I'm doing. I've downloaded Odin v1.85 and launched the phone in download mode.
All seemed to be going well and Odin saw the phone. I put the above file in the PDA section and left all the check boxes alone. I pressed Start and the little green bar got bigger with 'KERNEL' in the text box above. I got the following in the message area:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
The phone rebooted and now it is stuck on the very first screen with the yellow warning sign. I have tried to put the stock kernel back on, Kernel_I9100BVKG3.TAR, but it makes no difference. The phone is currently bricked.
Can anyone help?
Cheers,
Richard.
Click to expand...
Click to collapse
I think you have put clockworkmodmod on the phone and a custom kernel, that is why a yellow triangle shows up. I suggest that you should put the phone into recovery mode. It is the same key actions as download mode but you press the up volume button instead of the down button.When you have that up and running you will have options to install file from sdcard, mount, wipe delvik cache and other things. If you have this, in orange colour, then pull your battery out to switch off phone.
Your phone is not bricked.
It depends which country you live in to download the correct system.
Get back on here with the info and I will progress with you.
Sent from my GT-I9100 using XDA Premium App
Problem is already solved, bud.
Please help i hace bricked my galaxy s2 gt-i9100G
was trying to install jelly bean 4.1 so i went in recovery mode and did format wipe data but it got stuck so i removed the battery and after that cannot start the phone no bootlop no samsung logo nothin but i can go in downloading mode (volume down + home + power)
i tried many option but failed
tried installing pit file through odin
<ID:0/038> Added!!
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Set PIT file..
<ID:0/038> DO NOT TURN OFF TARGET!!
<ID:0/038> Get PIT for mapping..
<ID:0/038>
<ID:0/038> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
tried flasing new stock rom downloaded from samobile.com
<OSM> I9100GDXLC1_I9100GOLBLC1_I9100GDZKL3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> cache.img
and nothin after that
samething with kernel and bootloader it just doesnt install anything so plz help
warlock.911 said:
Please help i hace bricked my galaxy s2 gt-i9100G
was trying to install jelly bean 4.1 so i went in recovery mode and did format wipe data but it got stuck so i removed the battery and after that cannot start the phone no bootlop no samsung logo nothin but i can go in downloading mode (volume down + home + power)
i tried many option but failed
tried installing pit file through odin
<ID:0/038> Added!!
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Set PIT file..
<ID:0/038> DO NOT TURN OFF TARGET!!
<ID:0/038> Get PIT for mapping..
<ID:0/038>
<ID:0/038> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
tried flasing new stock rom downloaded from samobile.com
<OSM> I9100GDXLC1_I9100GOLBLC1_I9100GDZKL3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> cache.img
and nothin after that
samething with kernel and bootloader it just doesnt install anything so plz help
Click to expand...
Click to collapse
try flashing a stock/custom kernel meant for I9100G first via Odin and see
Sun90 said:
try flashing a stock/custom kernel meant for I9100G first via Odin and see
Click to expand...
Click to collapse
i also tried that and this is what shows in odin waited for 1hrs
<OSM> Leave CS..
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> cache.img
<ID:0/038> NAND Write Start!!
<ID:0/038> Transmission Complete..
<ID:0/038> Now Writing.. Please wait about 2 minutes
warlock.911 said:
i also tried that and this is what shows in odin waited for 1hrs
<OSM> Leave CS..
<ID:0/038> Odin v.3 engine (ID:38)..
<ID:0/038> File analysis..
<ID:0/038> SetupConnection..
<ID:0/038> Initialzation..
<ID:0/038> Get PIT for mapping..
<ID:0/038> Firmware update start..
<ID:0/038> cache.img
<ID:0/038> NAND Write Start!!
<ID:0/038> Transmission Complete..
<ID:0/038> Now Writing.. Please wait about 2 minutes
Click to expand...
Click to collapse
i guess because the formating/wipe complete data option from recovery mode eailier got crashed and wasnt complete (it got hanged so i pulled out my battery), i think it messed up my partitioned/storage system thats y nothin is being copied/installed.
some1 plz help
sum1 plz help really wtuck with the same problem since a week my only hope is download mode but sumhow its not helping
is thr a way to force update in odin mod cuz its getting stuck
warlock.911 said:
sum1 plz help really wtuck with the same problem since a week my only hope is download mode but sumhow its not helping
is thr a way to force update in odin mod cuz its getting stuck
Click to expand...
Click to collapse
You're sure you have an i9100G? (check model number on the label under the battery)
Also,
1. provide a link to whatever you are trying to flash.
2. make sure you have the usb cable plugged directly into a main port on the computer. Not through a hub, or a port on a keyboard or monitor, etc.
ctomgee said:
You're sure you have an i9100G? (check model number on the label under the battery)
Also,
1. provide a link to whatever you are trying to flash.
2. make sure you have the usb cable plugged directly into a main port on the computer. Not through a hub, or a port on a keyboard or monitor, etc.
Click to expand...
Click to collapse
yes i am 100% sure its i9100g i check it on the box and on my mobile also
and i cannot provide u link cuz i have like tried many thing i cud find on the net but i have also tried (http://forum.xda-developers.com/showthread.php?t=1457458) guide the G version also but as it get stuck nothing happen the phone only show downloading and there is no progress bar (the blue line that increase as the software gets installs) and my odin status is as i mention before (chache.img).i took it to the local technician but sum says there are 50-50% chances as while installing the phone is heating up and if they force it the ic might burn and sum say the hardware is short circuit. (if the hardware is short circuit will my phone be able to get into download mode as it does?)
http://forum.xda-developers.com/showthread.php?t=1619571
Try this...
Sent from my GT-I9100G using xda app-developers app
i dont wanna use odin
i have an slow internet,
while i cant download these drivers and all
I JUST WANNA UNBRICK MY SAMSUNG GALAXY S2 GT-I9100G
can i install this through recovery mode?
bhargav098 said:
i have an slow internet,
while i cant download these drivers and all
I JUST WANNA UNBRICK MY SAMSUNG GALAXY S2 GT-I9100G
can i install this through recovery mode?
Click to expand...
Click to collapse
How do you expect your PC to properly recognize the phone without any drivers?
Sent from my GT-I9100
......
Sent from my GT-I9100 using xda premium
:crying:
boki9999 said:
How do you expect your PC to properly recognize the phone without any drivers?
Sent from my GT-I9100
Click to expand...
Click to collapse
so if i get drivers, odin may favour me?
bhargav098 said:
i have an slow internet,
while i cant download these drivers and all
I JUST WANNA UNBRICK MY SAMSUNG GALAXY S2 GT-I9100G
can i install this through recovery mode?
Click to expand...
Click to collapse
Any chance of posting in the correct forum.
This forum is not for people with the crappy g variant lol.
Sent from my GT-I9100 using xda premium
theunderling said:
Any chance of posting in the correct forum.
This forum is not for people with the crappy g variant lol.
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
dude, just try to help me or shut up.
THIS FORUM IS FOR HELPING PEOPLE IN DEVELOPING,
not for people who make fun of the newbies
Up yours.Youve been told your not in the correct forum.....so go there or a Mod will be informed.
Sent from my GT-I9100 using xda premium
Bricking your phone is Android's way of telling you to get a Nokia. You're like the dodo - weak, fat, and underevolved. It's only a matter of time before you did something to brick your phone and when you did, just like the dodo, you will die out. It's the circle of life my friend, deal with it.
Indeed, like the Lemmings, you will be laughed at for years by subsequent users of Android. I saw "so i removed the battery" and laughed, laughed my way into a blissfull state of euphoria which only the cries of nature's rejects can elicit.
My Galaxy S2 I9100G is not powering on and is not charging anymore , even if insert a full battery inside the phone it will not power on , no access to download mode either .
any suggestion please , is my phone completely dead or there is something maybe that could revive it .
thanks alot in advance
machhho said:
My Galaxy S2 I9100G is not powering on and is not charging anymore , even if insert a full battery inside the phone it will not power on , no access to download mode either .
any suggestion please , is my phone completely dead or there is something maybe that could revive it .
thanks alot in advance
Click to expand...
Click to collapse
Never get a g variant.
Sent from the little guy
Hello everybody!
First of all, I'm not sure about my english skills...please have mercy on me :fingers-crossed:
Here I go:
I got my S3 in August/Sept with a T-Mobile Branding. My first action was getting it rootet and flashed with an official Samsung Rom just to get rid of the branding.
Two days ago I woke up to my charging S3 only showing the "Samsung..." Bootlogo. Removed the battery, nothing changed. Tried the Volume up-HomeButton-PowerButton Combo and it only resulted in a blinking logo (the logo disappears for a few seconds). The only thing I have access to is the Download-Mode.
What I tried since then:
Flashing a new one-part-rom with Odin, this was the result:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md 5 is valid.
<OSM> MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
<OSM> CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noshi p.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003>*Odin*v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!*
<ID:0/003>*
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Same with a three-part-rom.
Then I tried to downgrade the bootloader with ADB. But I don't get the drivers (Universal-Naked-Drivers) running. The S3 shows up as "unknown device" at the device manager but it doesn't want to be updated with the right drivers. PdaNet also refused to install USB-Drivers.
It's like they don't recognize the S3.. Perhaps I don't have USB-Debugging enabled? I'm not sure about this, because this brick just happened from one day to another.
I installed and uninstalled the "normal Samsung USB-Driver for mobile phones" often while trying to get the other drivers running. When installed, the S3 showed up in the device manager as one of the USB-Controllers.
Installed Kies for a factory reset but it didn't recognize the S3..
This shows up in Download-Mode:
ODIN*MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: Yes (3 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
I guess it's no sudden death because it shows the product name? Also I have no idea why it has three flash counts, I just flashed it once seven month ago.
Since I never updated to Jelly Bean the S3 was running on ICS 4.0.4
Edit:
Next steps I tried:
Flashing with an older version of Odin (v.1.85) But also failed at <ID:0/003> Complete(Write) operation failed
Flashing CF-Root v.6.4 to get the recovery mode back. Failed at <ID:0/003> Complete(Write) operation failed
Flashing Resurrection Odin CheckRom EvoHD v.4. Failed at <ID:0/003> Complete(Write) operation failed
Repartition with 20120329.pit and mx.pit. Failed at <ID:0/003> Complete(Write) operation failed
I'd still appreciate any kind of help or feedback!
It sounds like partial nand failure or simple partition corruption. Search here in q&a for solutions to repartition, but if that fails then your nand is probably toast.
try flashing a pit file
not sure if it will help but..
connect it to computer..when it fails to install drivers..Turn off and Pull battery out for few secs restart..
sometimes this helps to reinstall drivers..not sure in your case of a bootloop though?
Thanks for your answers!
I tried to repartition with a PIT-File but it didn't work.
At first I tried the GT-I9300_mx_20120329.pit with this 3-part-rom:
CODE_I9300XXALE8_554452_REV00_user_low_ship.tar.md5 is valid.
MODEM_I9300XXLE8_REV02_REV04_CL1145430.tar.md5 is valid.
CSC_OJV_I9300OJVALE7_CL547448_REV00_user_low_noship.tar.md5 is valid.
But the same error appeared.. also the error appeared so fast I don't think there happened a repartition at all?
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Second try was 3-part-rom recommended with the mx.pit-File:
CODE_I9300XXALEF_611327_REV00_user_low_ship.tar.md5 is valid.
MODEM_I9300XXLEF_REV02_REV04_CL1147871.tar.md5 is valid.
CSC_OXF_I9300OXFALEA_613742_REV00_user_low_ship.tar.md5 is valid.
With the same result...
It's always the same error, again and again...
Any further ideas?
you are done
Only two answers one wrong PIT or partition damaged .
Two Nand damaged see how much will a new motherboard cost .
jje
Thanks again!
With the GT-I9300_mx_20120220.pit-File I got my S3 responding for the first time since it died. It showed the blue loading-bar, but it didn't move at all and Odin stopped at <ID:0/004> NAND Write Start!!
Tried this rescue-version http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 with mx.pit but of course it didn't work..
you are done
Click to expand...
Click to collapse
seems like you're right, unfortunately..
But if you have ANY idea what I could try, please post it.
Are you sure it's a NAND damage or could it be a bootloader problem? I found this thread: http://forum.xda-developers.com/showthread.php?t=1916796 but I don't understand what they are talking about yet.
Update:
I couldn't find a solution and send it to a Samsung repair service and it was repaired under warranty. Don't know why exactly..they didn't need to because of my flash-counter. There was a letter in the package that said the mainboard was replaced and that's all!
Anyways, thanks for the help!
Can be closed!
Possible Solution
xylakant said:
Update:
I couldn't find a solution and send it to a Samsung repair service and it was repaired under warranty. Don't know why exactly..they didn't need to because of my flash-counter. There was a letter in the package that said the mainboard was replaced and that's all!
Anyways, thanks for the help!
Can be closed!
Click to expand...
Click to collapse
I had a similar problem, my phone just froze in the middle of a phone call, had to pull out battery, and when i tried to turn it on, it wouldn't pass the second "SAMSUNG" logo, just stayed there forever, with the blue light (Official JB 4.1.2 - not rooted)... Anyway, after 3 days of trying, downloaded bunch of firmwares, but all of them gave me the infamous "Complete(Write) operation failed". This is how I MANAGED to revive my i9300 16Gb Int:
1.Open ODIN, load ONLY the pit file corresponding to your phone (In my case i9300 16Gb Int'l - GT-I9300_mx_20120220.pit), check "Repartition" and "F.Reset Time" and hit "Start".
- If this step goes OK (All threads completed. (succeed 1 / failed 0))
2. Click on the "Reset" button in Odin (or close and re-open it), in PDA select "recovery-cwm-touch-6.0.1.2-i9300.tar", make sure only "F.Reset Time" and "Auto Reboot" are checked, and flash it. If everything goes OK, you should now have CWM instead of Stock recovery.
3. Take any microSD card, any size, and put THIS file on the root of the microSD using a card reader or whatever you prefer - but be careful, copy the zip as it is - do not unzip it.
4. Insert the memory card in the phone, enter recovery*, and select "Install zip from External Storage" and choose the file you put on the root of the card (by the way, it's a 4.0.4 downgrade bootloader), it should flash in a second, the phone will restart, and that's it!
5. Download and flash 4.0.4 Stock FW using Odin (i used "I9300XXBLH1_OXEBLF1.zip"), everything should go OK, and the phone will be bootable again.
*(my phone didn't wanted to enter recovery the old fashioned way using 3-button combo, but i managed to enter recovery from charging mode, by connecting the charger on a switched off phone, and as soon it starts charging press Vol Up + Home + Power, and when the FIRST Logo (Galaxy S III GT-I9300) appears, let go of the power button, keep pressing the Vol Up + Home, and it enters recovery).
ATRAC3 said:
1.Open ODIN, load ONLY the pit file corresponding to your phone (In my case i9300 16Gb Int'l - GT-I9300_mx_20120220.pit), check "Repartition" and "F.Reset Time" and hit "Start".
- If this step goes OK (All threads completed. (succeed 1 / failed 0))
Click to expand...
Click to collapse
Odin Stuck at "Set Partition" ^^
"<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
Help ?
Did you give it the pit file? Pit is really a last resort AFTER you've ruled out sending for repair
Sent from my GT-I9300 using Tapatalk 4
I have the pit file and Checked the Box ^^
MrFraggii said:
I have the pit file and Checked the Box ^^
Click to expand...
Click to collapse
Correct PIT file ??? for your phone ??
Flashing PIT 99% kill the phone .
You require a service centre .
Warranty will depend upon their report .
jje
Have the right Pit file ^^ But odin Stuck at Set mapping
MrFraggii said:
Have the right Pit file ^^ But odin Stuck at Set mapping
Click to expand...
Click to collapse
Where can you download these 16, 32 or 64 .pit files ? I couldn't find them anywhere ...
If you start playing with PIT files you will end up with a dead phone and at best have to buy a new motherboard .
They might be found on sammobile
jje
JJEgan said:
If you start playing with PIT files you will end up with a dead phone and at best have to buy a new motherboard .
They might be found on sammobile
jje
Click to expand...
Click to collapse
Thanks for the lead, I will look for them on Sammobile.
But Please, this is the only answer I could reald along my searches "do not mess with .pit file". That does not answers the "where" and "which file" questions. I think people know playing with .pit files is touchy and they have a reason to ask for it.Stop being their mother and just answer the question accurately !
tris16 said:
Thanks for the lead, I will look for them on Sammobile.
But Please, this is the only answer I could reald along my searches "do not mess with .pit file". That does not answers the "where" and "which file" questions. I think people know playing with .pit files is touchy and they have a reason to ask for it.Stop being their mother and just answer the question accurately !
Click to expand...
Click to collapse
Your sense of entitlement is awe inspiring, if you searched and read you would find many people who flashed pit files to fix just a soft brick and then had to pay for a new motherboard.
So no, we won't help people wreck their phones.
Pit Files
tris16 said:
Where can you download these 16, 32 or 64 .pit files ? I couldn't find them anywhere ...
Click to expand...
Click to collapse
This is where i got mine.
http://forum.xda-developers.com/showthread.php?p=30547929
Hello, guys. First of all sorry for my english, but I need help.
I am here because I dont know what to do, I have tried everything without success. Let me explain: I have a S3 GT-I9300, I have had it since 2013 and I have gone through everything with it: brick, several rom, resets, etc. On saturday I woke up and my phone was in a boot loop, but I said ''bah, I can fix it in 20 mins'', but as you can see I couldnt do it. First of all, NAND write start error appeared, I havent seen that error before, then partition errors appeared too.
I can enter to dowload mode and it says GT-I9300 in product name, I can enter to recovery but I cant do anything there
I have tried to flash the same stock rom that I always have, it is an emergency firmware that I have used like 5 times, so.... It is weird that it cannot fix this up. I also have tried with Sammobile's firmware, with and without pit, in 3 usb ports and with 2 usb cables and always the same result: FAIL.
I hope you can help me, buying another phone in my country is difficult.
It can be a hardware issue on emmc of the phone if failed after so many different tries
dusterphil said:
It can be a hardware issue on emmc of the phone if failed after so many different tries
Click to expand...
Click to collapse
And what can I do about it?
What is the Odin error? Post the Odin log.
audit13 said:
What is the Odin error? Post the Odin log.
Click to expand...
Click to collapse
This is one of those:
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping...
Then it does not do anything (in this case I used 4 files + pit, and those files and pit are the ones that I have always used)
The other one is this:
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
This was the first error that appeared. (this is with sammobile's firmware)
The sboot.bin file is the bootloader. It's probably failing to flash for one or more of the following reasons:
the bootloader in the phone is newer than the bootloader in the ROM being flashed;
the ROM is not for the phone being flashed;
need to try a different USB cable;
need to try a different USB port; and/or
the memory chip in the phone is damaged.
Borked nand. If the rom and cable are known to be good and 2 pc's fail then dead nand. It's unfortunate but it happens.
Beamed in by telepathy
I think the phone is dead, it have faught a lot in this years. Thank you anyways
jeanavila_ said:
I think the phone is dead, it have faught a lot in this years. Thank you anyways
Click to expand...
Click to collapse
It's time for you to get a new model
So here's the situation, I was using my phone for taking pictures of my project , then suddenly my phone shuts down , and when i tried to turn it on, it wont stop rebooting . I can't access the recovery mode, I can access the download mode tho. but im certain that the Usb debugging isn't enabled. And I get this error in odin whenever im flashing a stock rom.
here's the log I get on odin:
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1101)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I was hoping that someone out there can help me. Thanks in advance
shacs1412 said:
So here's the situation, I was using my phone for taking pictures of my project , then suddenly my phone shuts down , and when i tried to turn it on, it wont stop rebooting . I can't access the recovery mode, I can access the download mode tho. but im certain that the Usb debugging isn't enabled. And I get this error in odin whenever im flashing a stock rom.
here's the log I get on odin:
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1101)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I was hoping that someone out there can help me. Thanks in advance
Click to expand...
Click to collapse
Try to find answer in this thread.
https://forum.xda-developers.com/galaxy-s3/help/odin-partition-error-flash-t3738974
Pisonja said:
Try to find answer in this thread.
https://forum.xda-developers.com/galaxy-s3/help/odin-partition-error-flash-t3738974
Click to expand...
Click to collapse
Hello! I still cant find the solution for my phone there.I tried every steps that is stated there but nothing seems to work. I need help please. thanks
shacs1412 said:
Hello! I still cant find the solution for my phone there.I tried every steps that is stated there but nothing seems to work. I need help please. thanks
Click to expand...
Click to collapse
Download Flexihub and teamviewer, and send me your user and password for teamviewer in pm. I will try to do it for you.
Pisonja said:
Download Flexihub and teamviewer, and send me your user and password for teamviewer in pm. I will try to do it for you.
Click to expand...
Click to collapse
Is there a free version of flexihub? I cant pay for that price
shacs1412 said:
Is there a free version of flexihub? I cant pay for that price
Click to expand...
Click to collapse
just download and install, no need to register or buy. i will use my account.