Hey folks,
I'm having some issues with my ATT Atrix. The phone keeps rebooting at the "Rethink Possible" screen. I bought this phone off of somebody on CL. I actually had the phone make it past the att screen a couple times. It made it to the setup up Motoblur screen but when I clicked start it just skipped it and takes me to the "Emergency Calls Only" screen. However the phone would just restart eventually at this screen as well. When the screen timed out I could not get the screen to turn back on at this point unless I unplugged the USB cord and plugged it back in. When the phone was on the Emergency Calls screen, my computer did recognize the phone and it did launch the motorola website. While I had the phone at this screen it did say that it had to force close android.process.com. I am coming from a captivate with rooting and flashing roms so I am familiar with Android. I am just trying to figure out where the problem could be with my Atrix. I am hoping somebody can point me in the right direction. Thanks for your time!
Your best bet will be to SBF that back to stock. Have you tried that yet? If not search for RSD Lite and SBF in the forums. There are several links and guides.
Is it unlocked?
I am not sure if it is unlocked as I cannot get past the emergency call screen. However, I will search SBF and research that option of setting it back to stock. I know when I flashed roms on the Captivate I would enter into recovery mode. I see in the Atrix that I would have to use Fastboot? The only reason I am worried about flashing a rom is that the phone reboots on its own so I would not want to hard brick it if it rebooted during a flash.
If it's unlocked you should see the word "unlocked" in the upper left corner of the boot logo screen, unless it was unlocked then flashed back or fruitcake in which case it will not say unlocked.
You should not have issues flashing from recovery if you have enough juice in your battery, which you maybe don't if you have been letting it sit rebooting. The rebooting is more than likely caused by an issue with a kernel, ROM, etc. Think of recovery as being similar to the BIOS on a PC. You enter into BIOS before the OS boots, etc., and this is before all the hardware has initialized and drivers have loaded, so the problem causing the reboots should not exist at that time. I would definitely try flashing a different ROM, and also a stock kernel.
It never said unlocked when I got the phone to turn on. I am having trouble getting the phone to turn on this time. I have downloaded RSD Lite and the 4.5.91 .sbf file to flash. I am just having trouble getting the phone started. Are there any ways to force the phone on. When I press the power button the green LED stays lit but nothing comes on the screen. When I plug into the charger it shows the moto symbol then goes to the Battery charging screen. Im not sure if the battery is correct because it says BHX5 1500mAh on the battery. Thanks for your help guys!
Update: I can get the phone into Fastboot and then Android Recovery Mode when the phone is plugged into the wall charger. However when I connect the phone to the computer via USB it just shows the green led when the phone is powered on. Anyway I can get the phone to boot into Fastboot while connected to the computer via USB?
Bump. Any way to get the phone to turn on when plugged into the computer or anyone know why there would be an issue of the phone turning on when plugged into the wall charger but only showing the green led when plugged into the computer? The battery shows 100% charged. Thanks
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
nishith611 said:
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
Click to expand...
Click to collapse
Did you fastboot -w before flashing the sbf? (Guess you don't really need to when flashing a sbf)
What may also help is flashing the boot.img file from whatever ROM you are using via fastboot.
Don't know if this will help, but it solves an issue when flashing to a different ROM from CM7, so maybe will help for you.
I know this might sound dumb, but do you have a sim card installed? Also, try to boot into recovery and just do a factory reset. @CaelanT already pointed out that this should be unnecessary since you flashed an sbf but it wouldn't hurt to try.
nishith611 said:
Update: I got the phone into RSD mode and flashed the 4.5.91 sbf but the phone only goes to the Emergency Call Screen. Is there anything else that can be done?
Click to expand...
Click to collapse
EDIT: I reread the OP and realized he had already tried to bypass the start screen.
That is not the correct battery. That is actually a battery used for the Droid X/X2. It seems they have pulled a switch-a-roo on you. (Probably because the Atrix battery could be used as an "Extended" battery in the DX/DX2) Anyways, it should still work but you can find the correct battery online, it should be a BH6X and should have a capacity of 1880/1930mAH.
nishith611 said:
...Im not sure if the battery is correct because it says BHX5 1500mAh on the battery. Thanks for your help guys!
Click to expand...
Click to collapse
Thanks for the reply. I tried to get the phone into recovery mode. I get to the Exclamation Point screen but it gives me no options for a factory reset. I saw that you have to touch the lower right hand side of the screen, but this doesn't do anything for me.
As far as flashing the boot.img file for the rom that I used. I flashed the stock 4.5.91 motorola rom. How can I find boot.img and would I flash it using RSD?
Also would it help if I flashed a custom rom instead of the stock Motorola 2.3.4 rom?
Could the battery not being the BH6X rom be the issue for it not getting enough power to stay on by itself?
Thanks for the help guys, I really appreciate it!
No, the sim card was not installed during the flash. However, I did install the sim card afterwards but the phone boots up and goes to the big green battery charging screen and does not go any further. However when the sim card is not plugged in I can get the phone to go to the Emergency Call screen.
nishith611 said:
As far as flashing the boot.img file for the rom that I used. I flashed the stock 4.5.91 motorola rom. How can I find boot.img and would I flash it using RSD?
Click to expand...
Click to collapse
The following are the instructions for flashing the boot.img. this was the solution to bootloops when trying to restore to a different ROM after CM7, but as I said previously, you never know if it will help or not:
1.Open up the Zip file of your current Blur ROM (Ninja, CherryBlur, Alien, etc.)
2.extract the boot.img file and copy to the directory where your fastboot is.
3.Pull phone battery & reinsert
4.Power on phone and go straight to Fastboot mode (Power + Vol Down)
5.Type "fastboot flash boot boot.img" (exclude quotation marks)
6.Once flashed, reboot phone using "fastboot reboot"
Sorry, don't know how to extract the boot.img from a sbf. Did a quick search and couldn't find instructions. Not something I have done before. Maybe someone else can help with this. I don't even know if this will work, but anything is worth a shot when you are stuck.
<edit> Which CWM are you using?
You can flash Romracers via fastboot if you are not using it. This may help you get into recovery.
Update: I got the phone to recognize the sim card and make phone calls and get wifi active. But the phone still reboots by itself. I can use all the functions of the phone except it just reboots by itself. I got into the About phone section and it says
Android: 2.3.4
Kernel: [email protected] # 2
I can get into the Android Market as well as everything else. Could this be a hardware issue that causes the phone to reboot by itself within a minute or so?
Edit: I can get the vol up and down buttons to work while the phone is working but the power button is not responsive to let me power the phone off. Could a hardware issue with the power button be causing the constant reboot loop?
Update: I got the phone to function with the OS working just fine (phone calls, texts, emails, etc..) but it keeps restarting on its own. The power button still does not work however, could this be a hardware issue? Thanks
So I attemptted to unlock my bootloader for the Atrix, 2.3.4, and it was already rooted. I was using this link http://forum.xda-developers.com/showthread.php?t=1182871 and using the following video http://www.youtube.com/watch?v=S6a0BWquqAc.
Now I was at the screen where it said that the Boot Failed and I took out my battery and put it back in. Now I am stuck on this screen.
SVF:105:1:2
Failed to boot 0x1000
PwrReason: PWT_KEY_PRESS
Starting Fastboot Protocol Support
It has been on this screen for a while now and I am very confused on what to do and how to do it. Any Answers? Did I brick my phone? How do I unbrick? I have tried to take out the battery and did a lot of combinations but nothing is working. I'm sorry, I am a noob at this. Thanks, any help would be appreciated
So instead now I am able to choose between the modes (Recovery, Fastboot etc.) but now when I try to go into fastboot mode it says my battery is too low. It also won't charge at all. Would using someone else's Atrix battery work?
yes another battery would work no prob and i used same method to unlock. mine froze rite after and couldnt run the fix. pulled battery for 30+ seconds and was able to run the fix. another option is to find an external charger
Bricked stock MoPho. One day crashed and will no longer properly boot.
Cracked screen for a while now so warranty replacement not an option.
”Failed to boot 1” appears on M Dual Core screen on regular power attempt
“Failed to boot 1
PwrReason: PWR_KEY_PRESS
Starting Fastboot protocol support” appears on M Dual Core screen when hold Power and Volume Up
Screen briefly flashes and then goes black when hold Power and Volume Down
I have already attempted to flash stock Photon sbf file. Failed message after 99%
I have also attempted to flash stock Electrify sbf. Failed message right after process started.
Tried to flash on both regular power on and also on Power and Volume Up
Using RSD lite on windows7 64 bit.
Any ideas?
What was your build number?
Which photon sbf flashed?
Which electrify sbf flashed?
We need informations.
bull the battery out of the phone. plug phone into the pc then put the battery back in the phone. the phone should boot to the m logo and say failed to boot 1 it wont say rsd mode but its in rsd mode if you open rsd lite on the pc you will see the phone.
Files used:
1FF-sunfire-user-2.3.4-4.5.1A_SUN_USC_16.7-16-release-keys-signed-USC-US.sbf
1FF-sunfire-user-2.3.4-4.5.1A-1_SUN-154_MR-3-CM-release-keys-signed-Sprint-US.sbf
I don’t know exactly what Photon software version was on phone when bricked.
Ok, this looks like you're on the same boat with me and you need to unlock your bootloader, nothing more. If you want to use 4g, than there is no other way, only upgrading to the world of 2.3.5 sv2 locked bootloaders. But I suggest you, don't do that.
Thanks anyways guys.....still looks like I'm stuck with a worthless piece of equipment.
I don't think so, but you need to read in tegra sbf thread in development section, did you try to unlock?
having same prob and cant figure out
gui529 said:
having same prob and cant figure out
Click to expand...
Click to collapse
And do you want some help?
http://theunlockr.com/2009/10/06/how-to-set-up-adb-usb-drivers-for-android-devices/
Download the device manager thing for Motorola and try SBF agian
So I bought myself an Atrix last night, its completely mint. Except the phone is bricked.
I've done basic flashing on my Samsung Nexus i9250 and on other LG's and HTC's so I understand the surface level stuff.
Now, the Atrix powers on and hangs on the Motorola Logo says "UNLOCKED" in the top left corner, (I'm assuming bootloader is unlocked)
And I get a modem did not power up (0) shortly after it hangs for a while.
I've read on another thread that this is a hardware issue and it can't be fixed via flashing.
I'm hoping that's not entirely the case, the only thing I can do is boot into Android (no BP), and it restarts after a minute or so.
And I can boot into recovery, this phone has TWRP, which I did not put on, and am not used to.
Anyway I've been trying to revert to a stock rom, (assuming bell because I'm in canada) but I can't get my fastboot to go.
It just stays on "starting fastboot protocol" and RSDlite doesn't recognize it. (battery at full charge)
That is about the jist of it.
I'd like to see if a stock rom, recovery and radio image will get this guy up and going again.
Hopefully I can switch TWRP for CWM, or back to stock with fastboot and RSDlite, I don't totally know the process.
Thanks for any and all help in advance
I've got CWM now,
I think I maybe having a hardware issue.
Everytime I try to flash radio's through CWM or RSD, I get some sort of failure.
I can flash radio's through fastboot but it doesn't seem to help my situation.
Currently I'm flashing with RSD, first time around my device was an NS Flash Olympus and it failed at writing BP.
Now its an SE flash Olympus And I'm trying the same SBF.
It seems to fail when it switches to BP Pass through mode.
:/
Edit: In RSD everything is N/A
I can boot into Android on the no BP setting.
And flick threw a few menu's then the phone would die.
Baseband is unknown, I managed to get there in settings.
Anyone have any idea as to what is wrong here?
I'd like to know if I'm SOL so I can let the atrix gather some dust on the shelf.
Yep, it sounds like somwthing is messed up on the modem Hardware
Enviado desde mi MB860 mediante Tapatalk
Hey all, I have a phone im trying to fix for a friend. Im pretty sure he bricked it. It will not boot normally and is stuck in safe mode. I boot to recovery and load the rom he has on the SIM card but no luck. I just want to get this phone back to stock.
It loads to safestrap 1.07 Which after doing some research is quite old. Ive never worked with one of these phones so bear with me please.
Thanks for the help.
Small update, and bump. I havent had time to check it out myself but If I plug it into the computer and try to start it a White led stays on in the front of the screen. IT will not pick up via usb on my pc so I cant charge it or access it it seems. This is an XT910 as well