Ok，I cut two squares out of the plastic to expose the charging contacts.
This is confusing, it looks clean though
sent from my Note 2
Looks like he cut two squares out of the plastic to expose the charging contacts. If anyone sells parts for these we could just buy the plastic from a variant that comes with access holes and put it on the Verizon version.
Sent from my SCH-I605 using xda app-developers app
Care to go into a lil more detail?
Sent from my SCH-I605 using xda app-developers app
mchlwvr614 said:
Looks like he cut two squares out of the plastic to expose the charging contacts. If anyone sells parts for these we could just buy the plastic from a variant that comes with access holes and put it on the Verizon version.
Sent from my SCH-I605 using xda app-developers app
Click to expand...
Click to collapse
The last person i recall trying to swap the rear frames ended up with no LTE and no wifi. :crying:
It looks strightforward, but i would definitely like some more detail from the OP.
Did you have to add an copper material to the charging contacts in order for them to make contact with the QI terminals?
Unless our phones differ then yes he added material I did a similar process works great
Any1 trying this you need to be very careful
Sent from my SCH-I605 using xda app-developers app
What did you add? It seems like it would be easier and safer to add a good bead of solder to each terminal on the QI piece. This way if you do make a mistake you're ruining the charging accessory and not the phone.
mchlwvr614 said:
Looks like he cut two squares out of the plastic to expose the charging contacts. If anyone sells parts for these we could just buy the plastic from a variant that comes with access holes and put it on the Verizon version.
Sent from my SCH-I605 using xda app-developers app
Click to expand...
Click to collapse
From my experience doing this via the copper tape method, he would've not only had to do this but attached the charging pins to the motherboard that are seen through the mid piece as well.
sent from my Note 2
LOL are you [email protected]#ing kidding me. Verizon blocked up the contacts with plastic on their version of the phone, but left the actual internals the same?
WHY.
"Herp derp here let's take this amazing internationally launched phone and derp it down to our herp level." Stupid [email protected]#ing morons.
Ye I dont get it is it just under all thi
s plastic thats in the back of my phone??
littleguevara said:
From my experience doing this via the copper tape method, he would've not only had to do this but attached the charging pins to the motherboard that are seen through the mid piece as well.
sent from my Note 2
Click to expand...
Click to collapse
Sure.
I solder two stock contacts on the motherboard.
And cut two square holes in the plastic frame.
Buy a N7100 QI wireless charging back cover.
With any QI standard charging pad.
RainmanX said:
Sure.
I solder two stock contacts on the motherboard.
And cut two square holes in the plastic frame.
Buy a N7100 QI wireless charging back cover.
With any QI standard charging pad.
Click to expand...
Click to collapse
Where'd you get these pins to solder to the motherboard?
Sent from my Nexus 7
I've also been wondering where one can get those pins. I've not had much luck sourcing them.
Ben
Lmao, seriously. Verizon provides good service only because they invested in lte instead of another technology, unlike the other carriers, and lte won. I don't even care that they put their name on everything.they can do whatever they want with that respect. But they make some stupid decisions sometimes..stupid for the consumer at least. I can't guess what they benefit from doing that
Sent from my SCH-I605 using XDA Premium App
I just did mine and I used the cintact ground tabs off a old laptop. Worked great. No issues at all just a little solder some wire and a dremmel. Im lovin it.
Sent from my SCH-I605 using xda app-developers app
littleguevara said:
Where'd you get these pins to solder to the motherboard?
Sent from my Nexus 7
Click to expand...
Click to collapse
I got those pins and QI charger from taobao.com, about $40.
Does the back cover for wireless charging sacrifice nfc functionality? Might have been why big red decided to not include it on our 605s... They try to do the thinking for us and protect us from ourselves
Props to whoever found the contacts on the board!
Sent from my SCH-I605 using Tapatalk 2
nrinzema said:
Does the back cover for wireless charging sacrifice nfc functionality? Might have been why big red decided to not include it on our 605s... They try to do the thinking for us and protect us from ourselves
Props to whoever found the contacts on the board!
Sent from my SCH-I605 using Tapatalk 2
Click to expand...
Click to collapse
Don't even give them that kind of credit.
Everything on mine works
Sent from my SCH-I605 using xda app-developers app
Related
Hey Guys -
I know the wireless charging will work because of the Qi standard, but will the phone stay put? Any impressions from those who own it would be appreciated.
I could be wrong but I don't think its magnetic.. the back of the nexus is glass I think the orb is just a rubberized surface that "grab's" the back of the phone.. i.e. just friction holds it on... I think!
Sent from my HTC6435LVW using Tapatalk 2
Nobody has the orb yet, I think. It just now became available, with shipping withing a week. Plus the shipping time. I ordered one the first day it was available, but don't expect it before the end of next week.
Ok, they are shipping them today. Won't be long before we find out.
Sent from my HTC6435LVW using xda app-developers app
starscream86 said:
I could be wrong but I don't think its magnetic.. the back of the nexus is glass I think the orb is just a rubberized surface that "grab's" the back of the phone.. i.e. just friction holds it on... I think!
Sent from my HTC6435LVW using Tapatalk 2
Click to expand...
Click to collapse
I'm with you on this one, because I read it would be compatible with windows 8 and htc phones. And pictures look like the two circles on top are rubber. Just what it looks like to me
I have the touchstone charger and it has magnet in it.
from what I see it is held up 80% by friction, 20% by magnetic force.
Too bad the touchstone wont work on Droid DNA otherwise I think it would be a great charging dock.
Mine will be arriving tmrw (Friday)
sent from my Droid DNA
Here is a pic of the rear case of the nexus 4. I see no magnets.
Sent from my HTC6435LVW using xda premium
We'll know soon enough. The first ones arriving tomorrow. Today, in fact. Hope I won't have to return it.
Sent from my HTC6435LVW using xda app-developers app
cmay227 said:
Here is a pic of the rear case of the nexus 4. I see no magnets.
Sent from my HTC6435LVW using xda premium
Click to expand...
Click to collapse
I also see no inductive coils.... But they're there.
Sent from my HTC6435LVW using xda app-developers app
Magnet lightly holds. The surface of the orb is quite sticky and holds it just fine by itself - the magnet is obviously less apparent with a case on.
No case:
http://i.imgur.com/dXIyszGh.jpg
http://i.imgur.com/qHEeQmBh.jpg
With Diztronic TPU case:
http://i.imgur.com/wtnGcrdh.jpg
http://i.imgur.com/5qRZhYbh.jpg
Thing is pretty awesome.
---------- Post added at 11:14 AM ---------- Previous post was at 11:13 AM ----------
Definitely not strong enough to use as a car mount though.
beddachedda said:
Magnet lightly holds. The surface of the orb is quite sticky and holds it just fine by itself - the magnet is obviously less apparent with a case on.
[/COLOR]Definitely not strong enough to use as a car mount though.
Click to expand...
Click to collapse
Good to know.
Unfortunately, Play Store won't let me order one. My address is incorrectly input but I can't change it. Keep getting error messages.
Ty for the pics of this looks awesome will be ordering 1
sent from my beastly powered viper DNA using Tapatalk 2
Works like a charm! Together they're a thing of beauty.
So there is a magnet in it? I thought it would only be the anti-slip rubber that they try and sell for car dashboards. One question, does it work with the phone horizontal? That's something my Nokia DT-910 can't do.
Azbulldog said:
So there is a magnet in it? I thought it would only be the anti-slip rubber that they try and sell for car dashboards. One question, does it work with the phone horizontal? That's something my Nokia DT-910 can't do.
Click to expand...
Click to collapse
Yes there is a magnet, yes it works with the phone in landscape.
However, it doesn't activate DreamScene or whatever it does with the N4 (also doesn't flip home screens to landscape like it does in car mode).
beddachedda said:
Yes there is a magnet, yes it works with the phone in landscape.
However, it doesn't activate DreamScene or whatever it does with the N4 (also doesn't flip home screens to landscape like it does in car mode).
Click to expand...
Click to collapse
The dream mode is a 4.2 feature so I don't think anyone expected it to be on the DNA. And on stock there isn't landscape homedscreens. You'll either need a Rom or a 3rd party launcher for that.
Sent from my HTC6435LVW using xda app-developers app
Their are no magnets.
Sent from my Nexus 7 using xda premium
HTC Wireless charging unit
cmay227 said:
Their are no magnets.
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
is HTC planning to release its own Wireless charging device?
We will find out today
Sent from my HTC6435LVW using xda premium
I know a few people have pulled theirs off on purpose. My puppy chewed mine off and it irritates me not being there now. I had been looking to replace it and found this:
http://www.etradesupply.com/oem-htc-droid-incredible-x-droid-dna-charging-port-rubber-cover.html
$4 is cheap but it costs $18 to ship it.... has anyone found them for sale anywhere else?
I would email HTC first, they might send you one... I just needed a usb cable because mine broke and they sent a cable ans wallcharger!
Sent from my HTC6435LVW using xda premium
That is the only site I have ever seen that sells it. I looked a couple days ago and they didn't even have it in stock, looks like it's back now though. 18 dollars for shipping is kinda ridiculous if you ask me though.
Sent from my HTC6435LVW using xda app-developers app
If you want it bad enough.... I ripped mine off cause it was falling off anyway
Sent from my HTC6435LVW using xda app-developers app
I'd say it's not worth it at any price. It's just going to fall off again. Pretty much everyone I've known with one whether they liked it or hated it it still fell off soon or didn't function well anyway.
I always try to play nice with my phones. I hated that cover from day one but as always played nice (didn't rip or cut it off) but the day it fell off, I picked it up and put it in original box I also kept. My HTC incredible 1 and my HTC thunderbolt both made it till next upgrade with out that cover. Reminds me of those port covers on the older dumb phones that never really had a purpose but to make the port weaken over time, then go bad and phone quit charging. Not worth replacing at any price. But good luck to you if you really feel you need one!
Sent from my HTC6435LVW using Tapatalk 2
The first modification to a replacement phone is to rip that thing off!! Before I even turn it on even.:victory:
Ordered some micro USB port plugs oft some website: .50¢. Works well.
Sent from my HTC6435LVW using xda app-developers app
cstrife999 said:
I'd say it's not worth it at any price. It's just going to fall off again. Pretty much everyone I've known with one whether they liked it or hated it it still fell off soon or didn't function well anyway.
Click to expand...
Click to collapse
Mine works fine haven't had any problems and I'm always messing with it
Sent from my HTC6435LVW using XDA Premium HD app
I bought a used Employee Edition DNA and the owner ripped off the USB cover and did not mention it...
That site was the only one I found as well, and at first it was OOS but when it came back that shipping definitely killed it for me. Granted, it is shipping from Korea I believe, but it isn't worth it to buy a black USB cover... if it was Red I might have just sucked it up...
They may fall off "easily", but I have no use for the USB port right now anyway since I'm using a wireless charger... there are always ways to work around the USB cable to transfer files as well. Not sure why so many people look down on people who want to keep their flap intact...
raichur0xx0rz said:
I bought a used Employee Edition DNA and the owner ripped off the USB cover and did not mention it...
That site was the only one I found as well, and at first it was OOS but when it came back that shipping definitely killed it for me. Granted, it is shipping from Korea I believe, but it isn't worth it to buy a black USB cover... if it was Red I might have just sucked it up...
They may fall off "easily", but I have no use for the USB port right now anyway since I'm using a wireless charger... there are always ways to work around the USB cable to transfer files as well. Not sure why so many people look down on people who want to keep their flap intact...
Click to expand...
Click to collapse
Most of us just think it gets in the way. At least I do. Not that I mean to look down upon anyone.
Sent from my HTC6435LVW using xda app-developers app
cstrife999 said:
Most of us just think it gets in the way. At least I do. Not that I mean to look down upon anyone.
Sent from my HTC6435LVW using xda app-developers app
Click to expand...
Click to collapse
I agree that it does get in the way... so much in fact that I did not want to use a DNA until I got a wireless charger =\
I'm just a bit OCD with my phones and given that the back is red, and then there's a sudden black break along the bottom with the missing USB door... just looks off to me.
---
I wonder why even replacement DNA Body kits do not include the USB door either...
Mines got a nice fat crease in it from bending...stupid thing ain't worth a crap.
I mean does it really keep water out that well?
Sent from my HTC6435LVW using xda app-developers app
Only reason I haven't ripped it off is because of old phones the internal end would rattle around. Anyone noticing that or specifically not noticing so I can join the no plug club?
teckels said:
Only reason I haven't ripped it off is because of old phones the internal end would rattle around. Anyone noticing that or specifically not noticing so I can join the no plug club?
Click to expand...
Click to collapse
It may depend on how you rip it out. Mine was already removed, but it seems to be cut and the rubber end in the phone is staying put and does not make any noise. I'd take your cover if you do get rid of it though
John58543 said:
Mines got a nice fat crease in it from bending...stupid thing ain't worth a crap.
I mean does it really keep water out that well?
Sent from my HTC6435LVW using xda app-developers app
Click to expand...
Click to collapse
I would like to know if it really does keep water out as well, it says the phone is water resistant, but could that little plastic piece really hold back anything? FYI mine has been taken off as well so annoying to use i just said screw it and ripped it off one day. Haven't looked back since
For those of you that have replaced this rubber port cover, how easy/difficult was this process?
To replace the cover, you have to take off the entire back. The little port cover isn't held on by anything though, it just sits between the phone and the plastic backing. Unless you're an expert at taking unibody phones apart, it's not worth it because I broke the waterproof seal strip during the process. It was glued on.
Looks like you can get one for $6.80 here w/ free shipping
since I'm a n00b, can't post URLs ...
+++++++++++++++
site is electron-parts dot com
Item: #00023593
+++++++++++++++++++
Verizon offered to re-imburse me for mine, or by me a case that covered the charging port
Anyone find a place to buy the red side stripes... One of mine somehow got chopped in half and fell off
Sent from my HTC6435LVW using xda app-developers app
Hello, I recent brought his bumper on eBay, and I got to say, I love it very much, it adds no bulk to the phone and feels like its part of the phone instead of it as a case.
It's really slim and it protects the bezel. It lifts high enough to be able to put it face down, but the camera will touch if you put it down normally.
Also, keep in mind that the bumper uses a screw.
I had it for about a week, and have not notice any notable signal lost, but that's just me.
I got the case for 7.99, but it might be different depending on the eBay seller.
Here are the pictures of the black one, but if you guys like, I can also upload pictures of the red and silver one.
Sorry for the horrible quality, they were taken with my Nexus 7.
Could you post the silver and link where they were purchased. Thank you.
Sent from my SM-N900T using Tapatalk
aznmode said:
Could you post the silver and link where they were purchased. Thank you.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
http://www.ebay.com/sch/i.html?_odk...etal+Bumper+Frame+Case+galaxy+note+3&_sacat=0
theres multiple sellers, some are located in US, some are in China.
aznmode said:
Could you post the silver and link where they were purchased. Thank you.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
not at home right now, but silver like this in real life. it doesn't really look like the silver bezel we have on our note 3 so thats why i dont use it.
http://www.ebay.com/itm/Ultra-thin-...d=100005&prg=1088&rk=4&rkt=5&sd=190969000395&
No problem. Thank you for the link.
Sent from my SM-N900T using Tapatalk
Thank you for this, I was concerned about the signal loss, I just ordered mine!
Sent from my SM-N900T using XDA Premium 4 mobile app
Man I was going to order this one on amazon. Same everything just different name. I was worried hoe the inside of the casing looked and if it will scratch the sides of the phone.
Sent from my SM-N900V using Tapatalk
dadsterflip said:
Man I was going to order this one on amazon. Same everything just different name. I was worried hoe the inside of the casing looked and if it will scratch the sides of the phone.
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
theres this tiny strip that protects the phone from the aluminum.
gretschpr said:
Thank you for this, I was concerned about the signal loss, I just ordered mine!
Sent from my SM-N900T using XDA Premium 4 mobile app
Click to expand...
Click to collapse
haven't noticed any signal loss or there may be but it didnt affect me in anyway, my data speeds are still the same with it on or off.
@pham818 could you post a picture of the bottom where the charger is? Also it looks like it covers up the hole on the side for the mic? Is that true?
mazdamiata210 said:
@pham818 could you post a picture of the bottom where the charger is? Also it looks like it covers up the hole on the side for the mic? Is that true?
Click to expand...
Click to collapse
the side of the mic? you mean that hole on the bottom right side on the phone near the s pen location? yes it does. but its not a mic, its the temperature thingy. and okay, will do with the charger picture.
Can you still remove the battery cover? Just bought an extra battery/charger so I'm hoping so.
Sent from my SM-P600 using Tapatalk 4
aznmode said:
Can you still remove the battery cover? Just bought an extra battery/charger so I'm hoping so.
Sent from my SM-P600 using Tapatalk 4
Click to expand...
Click to collapse
nope sorry.
pham818 said:
nope sorry.
Click to expand...
Click to collapse
Thanks I was afraid of that.
Sent from my SM-P600 using Tapatalk 4
I had a very similar, not seeing other differences other than didn't say Love ME I on it and my signal loss was too drastic to use daily. Love the idea though. wish element would make a note 3 case.
Sent from my SM-N900V
blaine07 said:
I had a very similar, not seeing other differences other than didn't say Love ME I on it and my signal loss was too drastic to use daily. Love the idea though. wish element would make a note 3 case.
Sent from my SM-N900V
Click to expand...
Click to collapse
oh it didnt say love mei at all? like my black one doesn't say it on the side, but on the inside it does like every other ones that i own. maybe you should give this one a try, its only a few bucks.
pham818 said:
oh it didnt say love mei at all? like my black one doesn't say it on the side, but on the inside it does like every other ones that i own. maybe you should give this one a try, its only a few bucks.
Click to expand...
Click to collapse
Yea, just much have to. I love the aluminum bumpers... Just not in the best of signal areas, as is so it ices cake sometimes lol
Sent from my SM-N900V
I dont like how the bottom left has the little bump out for the screws. Makes it not fit in a seidio dilex holster.
idle0095 said:
I dont like how the bottom left has the little bump out for the screws. Makes it not fit in a seidio dilex holster.
Click to expand...
Click to collapse
just do it upside down lol.
I had this case cuz I bought it from a local store. I gave up on it after two days because it is so easy to pry apart when screwed on. It makes my OCD scream because it doesn't feel like it's on there, and dust can easily get into the pried crevice.
Sent from my fingers to your face using Tapatalk VIP on my Note 3 LTE!
Does anybody know how to disable the sview software that pops up while the OEM s view case is installed? I'm wanting to have access to Google Music lockscreen controls while the cover is closed. Thanks
Sent from my SM-N900V using Tapatalk
Should have saved $50 and bought a knock-off....
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
wroder84 said:
Does anybody know how to disable the sview software that pops up while the OEM s view case is installed? I'm wanting to have access to Google Music lockscreen controls while the cover is closed. Thanks
Click to expand...
Click to collapse
If you don't want the S-view functions at all, you could remove the IC chip from case.
stanglifemike said:
Should have saved $50 and bought a knock-off....
Click to expand...
Click to collapse
An excellent point although some folks have received a free case when they purchased their phones. Either way, he can still head over to ebay and get one if he doesn't want to screw up the OEM case.
N3 via Tapatalk
Knock off feels like a knockoff. But I have one in the mail so I will do a side by side. But you get what you pay for. I like the wake function but don't use most of the apps on the s view. I think it's crazy nobody knows how to turn it off. As much as we mod this should have been hacked a long time ago. This case just obviously isn't very popular with the people who do the modding. I will add info later to this post when i do a side by side. Hopefully it will be useful to someone.
Sent from my SM-N900V using Tapatalk
wroder84 said:
This case just obviously isn't very popular with the people who do the modding.
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
Or maybe it IS popular. I suspect the reason why no devs have wanted to disable the S-View functions is because that's the entire reason that bought it to begin with.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
stanglifemike said:
Or maybe it IS popular. I suspect the reason why no devs have wanted to disable the S-View functions is because that's the entire reason that bought it to begin with.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
Click to expand...
Click to collapse
Doubt that. I have the knockoff with the window and it's perfect with stock lockscreen and the lockscreen music far more usable than the sview cover software. There has to be another reason that's being overlooked.
Sent from my SM-N900V using Tapatalk
Lol, so the metal connectors in the case is actually just a simple piece taped to the case so I just peeled it off and at least I get music controls now. But the sview software has different touch sensitivity than the rest of the software so the screen is unable to be used while the cover is closed when not using the sview software.
Sent from my SM-N900V using Tapatalk
wroder84 said:
Lol, so the metal connectors in the case is actually just a simple piece taped to the case so I just peeled it off and at least I get music controls now. But the sview software has different touch sensitivity than the rest of the software so the screen is unable to be used while the cover is closed when not using the sview software.
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
You could turn the extra sensitive mode on for the touchscreen somewhere in the settings. It's called glove mode or something.
isn't the music control part of the s view software using the window, if you somehow disable the s view feature, the music function will also be disable, if you must disable, have you tried going into.
settings/more/application manager/all, and try to mess around the software to disable the feature if it's available, becareful not to disable the wrong features or some phone feature might not work.
Try sticking some tape over the metal connectors on the cover
Sent from my SM-N900V using xda app-developers app
I just got this in the mail and figured that I would contribute a bit of a review and some pictures in case anyone has any questions.
So far my first impressions are that it feels really good in the hand. Like the original S-View cover, it should also offer some basic drop protection due to the lip that surrounds the top, bottom and exposed sides. It is also a bit thicker in the rear than the plain S-View cover. The only way it is not protected is if I happen to drop it with the case open. I use an iloome flexible glass protector in case that happens, but let's hope not. I will not go into the S-View function as that has been covered pretty well on this forum, except to say I have had no issues with it locking with the front cover folded all the way back. I have tried it so far on a Tylt Vu charger and it worked well. It did get a bit warm, but I didn't find it a cause for concern. I also have a Nokia DT-900 charger to test with at the office. I will be sure to do that and let you know if it charges well. I tested NFC using my Nexus 7 and it worked well. The biggest flaw with this cover has been addressed by Spigen. I have added the magnetic clip to it and it is very effective. I have to say this cover looks very polished and professional, especially with the clip. Overall, I find that it kills 2 birds with one stone. It adds wireless charging, without the loss of NFC or S-view and it protects the Note 3 from minor drops. I haven't seen any drop tests with the S-View but it is a more substantial case than the first effort on the GS4.
S-view cover wireless
One more picture of the inside contacts.
b00mbstc said:
One more picture of the inside contacts.
Click to expand...
Click to collapse
Hi, ive ordered this exact same setup with the Spigen Clip.. just a small question though, does the spigen magnet affect the spen?
Ive read some where that other cases with a magnetic flap sometimes affects the accuracy of the Spen
mtsingson said:
Hi, ive ordered this exact same setup with the Spigen Clip.. just a small question though, does the spigen magnet affect the spen?
Ive read some where that other cases with a magnetic flap sometimes affects the accuracy of the Spen
Click to expand...
Click to collapse
I have not seen any impact. I can hover at the edge of the screen right next to the magnet with no change in responsiveness. I think the magnet only points straight up.
Nice. I also just picked up this combo from Amazon when the price for the S View case dropped. Should be here tomorrow, very happy to get these at the new discount.
Sent from my SM-N900V using Tapatalk
harajyuks said:
Nice. I also just picked up this combo from Amazon when the price for the S View case dropped. Should be here tomorrow, very happy to get these at the new discount.
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
Can you please provide the link? I do not see this on Amazon.
theROMinator said:
Can you please provide the link? I do not see this on Amazon.
Click to expand...
Click to collapse
http://www.amazon.com/Samsung-Galax...&qid=1389576126&sr=8-1&keywords=S+View+note+3
Sent from my SM-N900V using Tapatalk
harajyuks said:
http://www.amazon.com/Samsung-Galax...&qid=1389576126&sr=8-1&keywords=S+View+note+3
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
That is a different case/cover. I don't think the wireless s-view cover is on amazon yet. I have only seen it on Samsung and Mobilefun.
b00mbstc said:
The is a different case/cover. I don't think the wireless s-view cover is on amazon yet. I have only seen it on Samsung and Mobilefun.
Click to expand...
Click to collapse
Miffed it. Sorry about that.
Sent from my SM-N900V using Tapatalk
Bought mine from here and due to arrive today or tomorrow. Can't wait to get it. Tried using a QI antenna but messed with SView and would only charge in one place on charger. I will let you guys know if it is worth the purchase from here or if I bought a knock off. http://www.shopblt.com/item/samsung-ef-tn900bbesta-s-view-black-wireless/samdrv_eftn900bbestah.html
Sent from my SM-N900V
OK got my wireless SView case yesterday from the above link and its the real deal. Works perfect with my Nokia Fatboy charging pad. Charges to 100% while on or off. Does not get too hot while charging. This was a great deal. I would snatch them up while they have them in stock!
Sent from my SM-N900V
I got one of the pass through Qi receivers and it's working perfectly with the regular sview case. I'm happy with the results, maybe I would've gotten this case but for what I paid to get the sane function...meh
Sent from my SM-N900V using Tapatalk
---------- Post added at 04:24 PM ---------- Previous post was at 04:24 PM ----------
harajyuks said:
I got one of the pass through Qi receivers and it's working perfectly with the regular sview case. I'm happy with the results, maybe I would've gotten this case but for what I paid to get the same function...meh
Sent from my SM-N900V using Tapatalk
Click to expand...
Click to collapse
Sent from my SM-N900V using Tapatalk
initially I bought the QI antenna but would work through case and messed up my SView window. It worked well with the regular back on it and no case but need some protection as I work in a commercial environment.
Sent from my SM-N900V
Could you show us a picture of the back side of the S-View chip?
Edit: IOW, which of these does it look like?
Sent from my SM-N900T using Tapatalk
mdorrett said:
initially I bought the QI antenna but would work through case and messed up my SView window. It worked well with the regular back on it and no case but need some protection as I work in a commercial environment.
Sent from my SM-N900V
Click to expand...
Click to collapse
CZroe said:
Could you show us a picture of the back side of the S-View chip?
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
+1
Sent from my GT-N8013 using Tapatalk
Does anyone know how much thicker the wireless s view cover is compared to the normal s view cover. I can get them at the same price. I just want to add too much thickness to the phone.
Sent from my iPad using Tapatalk
Looking real pretty!
cydiamante said:
Does anyone know how much thicker the wireless s view cover is compared to the normal s view cover. I can get them at the same price. I just want to add too much thickness to the phone.
Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
Thick enough that the camera is barely recessed instead of protruding.
Sent from my SM-N900T using Tapatalk
Just to be clear for everyone looking at this thread, the one pictured is NOT the official Wireless S-View Cover! The one pictured is the Spigen Wireless S-View Cover, not the official Samsung Wireless S-View Cover (like the thread's title reads). Just don't want anyone getting confused, as the thread's title is very misleading and should be edited.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
stanglifemike said:
Just to be clear for everyone looking at this thread, the one pictured is NOT the official Wireless S-View Cover! The one pictured is the Spigen Wireless S-View Cover, not the official Samsung Wireless S-View Cover (like the thread's title reads). Just don't want anyone getting confused, as the thread's title is very misleading and should be edited.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
Click to expand...
Click to collapse
Umm I dont think so it is the original with a spigen magnetic clip on it.
Sent from my SM-N9005 using Tapatalk