Related
Hi Guys,
I am getting kind of desperate. I keep rebooting into recovery mode. Then, the screen shows Fastboot mode started... udc_start (). I think it is stuck. I am using LG Optimus ONE (P500). I have tried battery pull a lot of times. Doesn't work. Any suggestions? If you suggest I reflash stock rom or something, tell me how please. Thanks.
http://forum.xda-developers.com/showthread.php?t=944881
for flashing original firmwares
If you choose to reflash stock ROM, here is what you need:
- tools: http://forum.xda-developers.com/showthread.php?t=875881
- ROMs: http://forum.xda-developers.com/showthread.php?t=944881 or the link suggested in the tools thread
You may wait a little bit longer before reflashing to see if anybody has a better solution to your problem. Good luck!
More Questions... Help please if you can... Thanks
Hi All,
Thanks to those who have responded so far. I kind of needed the phone fixed ASAP, so I sent it for repair. But anyway, I have a few questions:
1)Is it possible to reflash stock ROM or a new ROM even if the the computer or Android SDK can't detect your device? (This is with the correct driver installed. When my phone was in the fastboot mode screen, it couldn't be detected as an LG Device at all when plugged in.) If you can, how?
2)For those who have successfully gotten a new ROM onto their Optimus One, how did you do it? Is there anywhere where the procedure can be found? And is it relatively safe? (I know there is always a chance you might brick your phone unless you are some expert, but there are some procedures that are safer than others right?)
3)This last question isn't really relevant to this forum section, but I'll ask anyway. Which phone models (any brand, preferably 2.2 onwards) are good for rooting and installing custom ROMs? Like, are there any phones that most rooting/ROM installing software supports? (For instance, I have heard that HTC phones can usually be flashed with custom ROMs without bricking that easily 'cos they are supported by stuff like ROM Manager etc.) And one more thing: what are the easiest/safest ways found to root/flash a new ROM?
Thanks everyone.
-----
Me, the random noob attempting to learn more about Android ROMs and rooting
Jonapedia said:
1)Is it possible to reflash stock ROM or a new ROM even if the the computer or Android SDK can't detect your device? (This is with the correct driver installed. When my phone was in the fastboot mode screen, it couldn't be detected as an LG Device at all when plugged in.) If you can, how?
Click to expand...
Click to collapse
Yes it is possible, you'll need to firstly boot into 'emergency mode', by pressing volume up + back + power when the phone is off. Then follow these steps to flash stock rom. You do not use Android SDK at all, all you need is for the phone to get into the emergency mode, it is what most people with bricked phones do to reflash.
Jonapedia said:
2)For those who have successfully gotten a new ROM onto their Optimus One, how did you do it? Is there anywhere where the procedure can be found? And is it relatively safe? (I know there is always a chance you might brick your phone unless you are some expert, but there are some procedures that are safer than others right?)
Click to expand...
Click to collapse
Personally, it was relatively easy for me even though I'm a new user to android. I've had my phone for 2 weeks and bricked it 3 times within the first 72 hours. But there are methods to get it back as I explained in Q1 XD In order to flash a new ROM, there are 3 MAIN steps.
1. root your phone
2. install custom recovery
3. make backup and flash new ROM
if you need help on certain individual steps, just post it here and I'm sure someone will help you.
Jonapedia said:
3)This last question isn't really relevant to this forum section, but I'll ask anyway. Which phone models (any brand, preferably 2.2 onwards) are good for rooting and installing custom ROMs? Like, are there any phones that most rooting/ROM installing software supports? (For instance, I have heard that HTC phones can usually be flashed with custom ROMs without bricking that easily 'cos they are supported by stuff like ROM Manager etc.) And one more thing: what are the easiest/safest ways found to root/flash a new ROM?
Click to expand...
Click to collapse
In terms of the easiest method to root, it is definitely to simply run an app that can automatically root the phone for you, such as z4root, or SuperOneClick are just 2 examples. So I'll say whichever phones these app support, will be the easiest to root. ROMs will depend on the users of those phones and their dedication to creating customisable ROM. You can find most of the phones and available ROMs on this forum anyway.
Is it possible to exit emergency mode? Do you do a battery pull or something? I am planning to test out booting into emergency mode when my phone comes back from repair. Will it harm my phone? (Does it do stuff like wiping system data or my installed apps?) Thanks in advance to anyone who will reply.
I think you can just hold power to turn your phone off in emergency mode, but if it doesn't work, you can always pull the battery out. You didn't mention what you did for this problem to start but unless you perform the same thing, you won't need to use emergency mode.
Stuck on Recovery mode
Hi Guys. my optimus s went into an emergency mode out of nowhere but i was able to recover using the KDZ Utility. the phone booted up and i did a re start and got stuck on recovery mode even is i use the KDZ Util or install a new rom it goes back to recovery mode . using ra OptS-2,2,1. what can i do if anything. please help.( dont know anything about sdk) Thanks & please help
DaBoricua said:
Hi Guys. my optimus s went into an emergency mode out of nowhere but i was able to recover using the KDZ Utility. the phone booted up and i did a re start and got stuck on recovery mode even is i use the KDZ Util or install a new rom it goes back to recovery mode . using ra OptS-2,2,1. what can i do if anything. please help.( dont know anything about sdk) Thanks & please help
Click to expand...
Click to collapse
when you said install a new rom, did you install it through kdz? if you did, try installing an optimus s rom through recovery. heres how:
download a rom on your computer
plug your phone in to you computer (with it already booted in recovery)
toggle usbms on your phone
transfer the rom to your phone
flash the rom
Hello. This is my first time actually visiting the Optimus One forum although I have had my phone for maybe 2 months. I was not going to root my phone, in case I need warranty, so I was using the stock rom, although it was a little slow.
So I thought MAYBE there is an update on LG website, so I went on there, and found out that I can update by connecting to the computer. So I did download all the files they required (at least I think I did), and I followed the instruction, and started updating. Here comes the first problem encountered: While the phone was n Emergency mode, during the updating was in process, it said Phone and PC has problem communicating or something like that. And there was a restart button. It said disconnect the phone, and remove battery and connect again, and then press restart. So I did. Then now after that the LG software update tool doesn't recognize the phone. It said connect it and press OK or something. I think this is the point where I bricked my phone. A NON rooted phone. So I don't even have a custom recovery to flash anything! I hate LG right now. They are so stupid. I don't know what happened..
I tried the method here:
http://androidforums.com/optimus-one-support-troubleshooting/237642-bricked-lg-optimus-one-help.html
But I couldn't download the right KDZ firmware for my phone, that is available in the link in that link above. I'm in Canada and my phone is from Koodo and the model name is P500H.
So I got a random KDZ file that's for P500 from internet, but the in the KDZ_FW_UPD emulator, that's in the link above, it says my phone is NOT detected! I reconnect the phone and restarted the software so many times. I think they want me to connect the phone while it's Turned ON, and press the "Connect to USB" button. I'm not sure though.
***PLEASE*** Help me! I really need to unbrick this..
Sorry for the long post. And Thank you!
to flash custom recovery follow http://forum.xda-developers.com/showthread.php?t=1318750
Then flash any rom in zip format from custom recovery (according to your baseband)(search development section of p500)
Once you can boot into rom , to revert back to stock condition follow http://forum.xda-developers.com/showthread.php?p=19006040#post19006040 or http://forum.xda-developers.com/showthread.php?t=1324105
mak.3736 said:
to flash custom recovery follow http://forum.xda-developers.com/showthread.php?t=1318750
Then flash any rom in zip format from custom recovery (according to your baseband)(search development section of p500)
Once you can boot into rom , to revert back to stock condition follow http://forum.xda-developers.com/showthread.php?p=19006040#post19006040 or http://forum.xda-developers.com/showthread.php?t=1324105
Click to expand...
Click to collapse
Thank you SO much for your reply. I was searching for HOURS, and Finally found out how to make the KDZ update tool recognize my device. A LOT of people can't get it to work, but I saw someone in this post http://forum.xda-developers.com/showthread.php?t=1015332&page=4
that you need to remove sim card and battery. So I did, and restarted the update, and YES! It worked! I was on Foryo, but I got Gingerbread Rom from
this forum http://mobilesyrup.com/forum/showthread.php?t=21446&page=2
And I'm actually on GB now!
OMG, I have so much homework, but have been doing this for the WHOLE day! Wow..
Thank you so much for your help anyway!
Oh thanks
Sent from my LG-P500 using xda premium
Chapter 1: The Foolishness of the User
Hi, I have the korean version of the optimus one(KU3700). It was on gingerbread(2.3.4) stock. I was trying to root it by downgrading it. I entered "adb reboot recovery" and I'm stuck. I tried to reflash it by going to emergency mode with the button combinations using the KDZ updater with this
"csmg. lgmobile. com:9002/swdata/WEBSW/LGKU3700/AKTFBK/KU370040_00/KU370040_00.kdz"
and it worked without any errors but when it when it came up it was still on recovery mode. Is there any way I can change the phone mode to the regular mode
Chapter 2: Journey to Salvation
For anyone who has this korean optimus one, after days of searching, I've found a web site that gave me hints to solve the problem. I just needed a different kdz file and I got it here:
h t t p://sirospace.tistory.com/category/Android%E2%97%86
popped it in google translate because I'm Filipino and can't read korean.
Downloaded the froyo kdz and flashed. I hope this can help other people stupid enough to play with their phones by typing random commands without knowing what it does, like me, LOL...so happy, now it's time to root
Chapter 3: False Hope
OK so I have successfully unbricked and rooted my KU3700, now The problem I have is installing a custom recovery on this phone, none of the images I try work.
Recovery images I have tried are as follows:
recovery-RA-GNM-thunderg-1.1.0.img
recovery-RA-GNM-thunderg-2.2.1.img
recovery-RA-GNM-thunderg-3.0.6.img
Every time it finishes and reboots, it gets stuck at the LG logo.
Chapter 4: Wisdom Within
Found the problem. The images above are for the P500.Even if the KU3700 hardware is similar to the P500, flashing firmwares made for the other model will result in errors. The same holds true for custom recoveries.
Chapter 5: The Plea to the Gods
I've contacted drellisdee and submitted the files needed for custom recovery creation for the KU3700.
Just waiting for the flash image now. Thank you everyone
Chapter 6: The Forgotten
It seems drellisdee is busy right now. I'm a windows user and knows nothing about programing. So if anybody can help I'm sure the KU3700 community would be greatful. I've attached the files I think are needed to make a custom recovery.
Chapter 7: Quest for the Custom Recovery
I got tired of waiting. So as a windows user with no experience in programming, I did a lot of copying and pasting, I managed to port clockwork mod using virtualbox following this website:
h t t p://www.koushikdutta.com/2010/10/porting-clockwork-recovery-to-new.html
So I have got a bootable and flashable custom recovery but nothing works yet. I still need to configure it according to the device.
I have uploaded the image and the build files. Please help me configure it and tell me what's wrong. I really don't know that I'm doing
PS: you can try flashing the custom recovery by doing "fastboot flash recovery /Path to/recovery.img and you can go to recovery by using android terminal and type "boot recovery". It will boot, but that's that LOL. Take out the battery to boot to normal mode.
Chapter 8: The Holy Grail
LOL, I found the answer again. I was so frustrated that I kept squishing the phone in recovery and found out that it was just a button configuration problem. A bit of research and I found out that I can toggle it by pressing volume up and volume down at the same time. WOOHOO!!! Custom Recovery at last
Chapter 9: Invasion of the ROMS
And here at last, the user is retired. But the adventure is far from over. It is foretold that the creation of the Custom Recovery will begin a new era. The key to open the gate has been found. So our hero will await the invasion of the ROMS<background music...> END
you can see at
tinhte.vn/threads/908874
Thank you for the reply but as I said, I can flash fine without errors it's getting back to regular mode I have a problem with. Rebooting and reflashing does not take me out of the recovery screen(it's just a opened box with an orange arrow and the android logo).
vidgen13 said:
Thank you for the reply but as I said, I can flash fine without errors it's getting back to regular mode I have a problem with. Rebooting and reflashing does not take me out of the recovery screen(it's just a opened box with an orange arrow and the android logo).
Click to expand...
Click to collapse
yes i see.but i'm newer android.i only send you link to fix
i hope have a pro android to fix your brick
This is just a shot in the dark because i didn't understand what you did entirely : have you used the combination to actually recover the stock rom after you flashed with KDZ ? (Home+VolDown+Power)
Yes already did. The computer can see the phone whenever I connect it except that I can't access adb. I may have to take this back to the store
vidgen13 said:
Yes already did. The computer can see the phone whenever I connect it except that I can't access adb. I may have to take this back to the store
Click to expand...
Click to collapse
Are you sure you flashed the right rom for your phone? There's an application that downloads the required rom for your phone according to your IMEI/SN, but i don't know if it works with the korean version.
Yes it's the KDZ file, unfortunately it's the only KDZ file out there for ku3700. Shouldn't have settled for this korean version
why you wanna downgrade the latest version?
Dude I have the same Korean edition as you.
Actually why you wanna downgrade the latest version.?
My phone had 2.2.2 and I did upgrade it into 2.3.4 I did it officially and I can tell you How to re-install 2.3.4 if you want.
asmOne said:
Dude I have the same Korean edition as you.
Actually why you wanna downgrade the latest version.?
My phone had 2.2.2 and I did upgrade it into 2.3.4 I did it officially and I can tell you How to re-install 2.3.4 if you want.
Click to expand...
Click to collapse
Thanks for the reply. I wanted to downgrade it to root it. And now I'm rooted. My only problem now is installing a custom recovery. I've already tried several custom recoveries:
recovery-RA-GNM-thunderg-1.1.0.img
recovery-RA-GNM-thunderg-2.2.1.img
recovery-RA-GNM-thunderg-3.0.6.img
but I get stuck at the LG logo when it reboots. I think it's because it's for the p500. So if you have a custom recovery for the ku3700 please help
I dont get it ,p504,p505,p506 are versions of p500??? And why some of our roms work on those phones?? So by logic this stock work on p500???
Sent from my LG-P500 using XDA Premium App
vidgen13 said:
Thanks for the reply. I wanted to downgrade it to root it. And now I'm rooted. My only problem now is installing a custom recovery. I've already tried several custom recoveries:
recovery-RA-GNM-thunderg-1.1.0.img
recovery-RA-GNM-thunderg-2.2.1.img
recovery-RA-GNM-thunderg-3.0.6.img
but I get stuck at the LG logo when it reboots. I think it's because it's for the p500. So if you have a custom recovery for the ku3700 please help
Click to expand...
Click to collapse
this method worked for my working KU3700 when I'm using my 1st KU3700 I also was struck as you and finely I realized there are No custom roms for Optimus one Korean edition (KU3700/SU370) and I had to connect my phone to an Octopus box (lg softwere box) via software box installed the official firmware. if this method not working you have to connect to a software box.
connect to the internet your PC and 1st install Driver and 2nd install the LG update tool. after installation connect your phone to computer and wait a five seconds for comport installation. after install your phone Run LG Update application.
it is connect to the server automatically indicating red line and after search for latest firmware.
if you can Update your phone it is shows Update butten.
Driver
http://www.4shared.com/file/C3BSNx9P/lgunitedmobiledriver_s4981man3.html
LG Update Tool
http://www.softpedia.com/get/Mobile-Phone-Tools/Others/LGMobile-Support-Tool.shtml
Thank you all for the quick answers, but I already have a rooted ku3700. All I need now is a working custom recovery. If someone has the same phone, please tell me which image is compatible
you can appear the emergency mood with android logo.
it means you have an Empty phone. your Os was been erased. You have to connect your phone to Octopus software box and box server has you original Os for your IMEI. this is the only solution. if you will able to solve this problem without a Software box please inform me. we can open a New Thread for Korean edition.
(ku3700/su370)
I already got out of the emergency mode without an octobus box. It's really simple, you just need to use a different kdz file. The hard part was looking for the kdz file. I have 3 kdz files. KU370017(froyo), KU370033(gingerbread-rootable), KU370040(latest one from LG, gingerbread-unable to root). Just flash with the KDZ updater. I'm on the second firmware because I can't root the latest firmware. To root it, I used super one click(latest version, use zerg rush option). Now I'm just waiting for a custom recovery from drellisdee so I can use custom roms. When I get it, I'll ask him if I can post it so we all can have uber phones LOL
Updated the thread. Can somebody help?
vidgen13 said:
Updated the thread. Can somebody help?
Click to expand...
Click to collapse
If you have flashed a working clockworkmod you can enter into clockworkmod via ROMManager (search in google play aka market). In ROMManager you have "reboot to recovery" option in case you want to go to recovery to flash something. Also you can try to flash from ROMManager a custom recovery (5.0.2.0 for oldBB or 5.0.2.7 for newBB), try to choose to phone model LGP500 oldBB, try and test if it's working. Wish you luck.
Thanks but I already have a working recovery. I just need some ROM makers now
vidgen13 said:
Thanks but I already have a working recovery. I just need some ROM makers now
Click to expand...
Click to collapse
Have you tried CM7.2? if your phone is very similar with Optimus One i doubt it isn't compatible with your phone.
If your phone use 2.6.35.10 or 2.6.35.14 kernel you can give a shot to try CM7.2 on your phone, but before try this make a backup first.
Check this thread Post Your CyanogenMod 7.2.0-RC1 Nightly Questions HERE!! for CM7 custom rom.
yep, it doesn't work. Is there a tutorial for building cyanogen for unsupported devices? All I can find are tutorials for supported devices. I've already got the source code from LG. The problem is just incorporating it in the cyanogen mod. I wish this phone had more users LOL
Hey all,
I have a CWM backup of my current rom and have backups of apps and data but am stuck at a bootloop.
As I have read countless articles, it seems my error is because I have a locked bootloader(not actually sure). Though, I only tried to flash
clockcycle's wiped v20d cwm backup file. It failed part way saying it couldn't write to /system.
Since then, I haven't been able to fully enter CWM. just see the red triangle with the droid guy on his back.
I have read Cmahendra's unbricking guide but it doesn't work as I have installed JB and even the tips to unplug, wait 10s and reopen the program to flash again it still won't work. Still stops at 15% saying error connecting to the phone.
There is a similar thread which had this exact problem which said to
use the online method to recover your phone since I had already installed JB. I edited the hosts file to remove the fake offline server and opened up the b2CAppsetup.exe, clicked on customer support,
entered my model LGP769BK and my S/N and it began to start the process and 'analyze' then crashed and said "updating is not possible any longer due to a fatal error while the LG mobile phone software Update"
I've tried to search this out myself and not waste any space but I'm at loss here. If anyone has any help, it would be much appreciated
as I don't have a phone while this is not working.
I've tried all the ways to to hard reset, master reset and still I get the droid guy on his back. I can get to S/w mode like all the other posts say to do but none of those fixes seem to work for me. Am I missing something?
Do I have any options here? I have kind of read that I should just unlock the bootloader but I don't think that applies in my case as I can't turn on my phone fully.
edit: for the online method(LG support tool), it basically cancels when it goes to the 'downloading' phase --> this is what I've seen as most of the answers but doesn't work
Upon further reading,
many seemed to need to replace their u-boot and x-loader
I did so and installed fastboot using Lelus' script here:
http://forum.xda-developers.com/showpost.php?p=41768774&postcount=1
I used option 6 which allowed me to flash the u-boot and x-loader from p760(works with my 769 and others as it says in the options) for JB
I'm not sure if I needed this as I don't have an unlocked bootloader.
I'm not sure of commands in fastboot but I ran
fastboot devices and it showed something
I also ran: fastboot flash recovery recovery.img
and I put one of my cwm backups in the "yours" folder
After I activate fastboot, it brings me to the C:\fastboot\yours folder
I assume this is for me to put my intended files in but I'm unsure if I should use my cwm backup or something else?
After it flashed the recovery img, I sent a fastboot reboot command
but it still went back to the droid lying down with a red triangle.
As some of you may see, I'm not too great with this but I feel like I'm close. Does anybody have an idea of what I should be doing?
should I flash an update.zip?
I don't know many commands but hopefully this gets me going in the right direction.
PLEASE HELP ME!!!!
I guess your cmw restore formatted your system but couldnt load the new system
the recovery you run with a locked bootloader uses a technique called 2nd init which i think is somewhere stored in the system partition. so when the recovery formatted the system, it lost itself too.
I've had a similar problem. the way out would be booting into the SW upgrade mode--switch off the device, remove the battery, remove the usb cable. press the volume up button and connect the phone to the computer. wait for a couple of seconds and then insert the battery.
you should be in the SW upgrade mode
now use the B2C client. if it gives an option to upgrade, use that otherwise, go to the customer support menu and press recovery phone
I have already done earlier. It may have gotten lost in my frenzy of information. I have put the phone into software mode, as you said, and it won't work either; There's no option to click upgrade because it's JB(V20D) and when I click recovery phone and enter my imei, LG mobile support tool(B2capp.exe) analyzes and then has a 'fatal error'
Since I flashed the new u-boot and x-loader my screens are all backwards/mirrored. Maybe the tool flashed an unlocked u-boot and x-loader if that's possible.
Is a recovery possible by fastboot?
I have a clean and full copy of my cwm recovery as well as apps and data backed up, I just need to get this phone in working order
shockah486 said:
I have already done earlier. It may have gotten lost in my frenzy of information. I have put the phone into software mode, as you said, and it won't work either; There's no option to click upgrade because it's JB(V20D) and when I click recovery phone and enter my imei, LG mobile support tool(B2capp.exe) analyzes and then has a 'fatal error'
Since I flashed the new u-boot and x-loader my screens are all backwards/mirrored. Maybe the tool flashed an unlocked u-boot and x-loader if that's possible.
Is a recovery possible by fastboot?
I have a clean and full copy of my cwm recovery as well as apps and data backed up, I just need to get this phone in working order
Click to expand...
Click to collapse
If you fastboot flash the u-boot and x-loader from p769(ICS) it should go thru with the offline flash detailed in cmahendras guide.
http://forum.xda-developers.com/showthread.php?t=2085344
Use the KDZ_FW_UPD.zip from this thread
Or try this
Remove all of the stuff you have downloaded for this. Download the original B2C client from LG's site and use that
Tablechair said:
If you fastboot flash the u-boot and x-loader from p769(ICS) it should go thru with the offline flash detailed in cmahendras guide.
Click to expand...
Click to collapse
Thanks.I'll try this. if I have the ICS bootloader, does that mean I'll have to flash the V10G kdz? or can i do the v20d kdz
dhruvbatra205 said:
http://forum.xda-developers.com/showthread.php?t=2085344
Use the KDZ_FW_UPD.zip from this thread
Or try this
Remove all of the stuff you have downloaded for this. Download the original B2C client from LG's site and use that
Click to expand...
Click to collapse
I have the updated kdz fw upd .zip from the unbrick and root thread as well as downloaded a new, official B2C client but they all still hang at the download part during phone recovery.
Tablechair, that did the trick.
Is this because the tool we use to flash for the offline method doesn't recognize the x and u-boot loaderse of JB?
After I installed the ICS boot loaders, my software upgrade mode wasn't mirrored anymore.
I did as tablechair and flashed the V20D.
Does anyone understand why this problem happened in the firstplace? Maybe I didn't get a full copy of clockcycle's backup cwm
or should I have not flashed his recovery in the first place since I didn't have an unlocked bootloader?
Again thank you for all your help and if anyone can provide answers to my other supplemental questions, that'd be great.
Off to root and probably unlock bootloader to be sure.
edit: I can't find the thanks button. but thank you very much tablechair. much appreciated. Hope this can help someone else
p.s. also big thanks to those who made the fastboot program for p769(Artas182x and sguerrini97). really an invaluable tool as I now know.
shockah486 said:
Tablechair, that did the trick.
Is this because the tool we use to flash for the offline method doesn't recognize the x and u-boot loaderse of JB?
After I installed the ICS boot loaders, my software upgrade mode wasn't mirrored anymore.
I did as tablechair and flashed the V20D.
Does anyone understand why this problem happened in the firstplace? Maybe I didn't get a full copy of clockcycle's backup cwm
or should I have not flashed his recovery in the first place since I didn't have an unlocked bootloader?
Again thank you for all your help and if anyone can provide answers to my other supplemental questions, that'd be great.
Off to root and probably unlock bootloader to be sure.
edit: I can't find the thanks button. but thank you very much tablechair. much appreciated. Hope this can help someone else
p.s. also big thanks to those who made the fastboot program for p769(Artas182x and sguerrini97). really an invaluable tool as I now know.
Click to expand...
Click to collapse
Things don't always go according to plan, maybe his Clockworkmod backup was made from the touch version and he didn't have artas182x second init recovery installed. So when the cwm failed the first time, did you try to restore your cwm backup?
kuma82 said:
Things don't always go according to plan, maybe his Clockworkmod backup was made from the touch version and he didn't have artas182x second init recovery installed. So when the cwm failed the first time, did you try to restore your cwm backup?
Click to expand...
Click to collapse
Not yet. having problems flashing a kdz again. I've tried the 2 different software modes, as well as setting emerg and diag but still getting stuck at 15% again.
Do i have to replace my uboot and xloader with the ICS ones every time I want to use the offline flash method?
edit: yup, after replacing with ICS loaders again i'm able to flash using software upgrade. will update on whether I can restore cwm
kuma82 said:
Things don't always go according to plan, maybe his Clockworkmod backup was made from the touch version and he didn't have artas182x second init recovery installed. So when the cwm failed the first time, did you try to restore your cwm backup?
Click to expand...
Click to collapse
I realized I misread your question. When I flashed before the incident, it failed to write to system and I didn't restore my other folder. I rebooted and it was all missed up. Anyway, now that I've got everything back and now with an unlocked bootloader, i was able to recover my old image. However, data isn't working so I have to find the radio to flash as I recall reading in other threads.
Can someone explain in laymen terms why this is? recap, i was on unlocked bl rooted jb and I flashed my old cwm backup when I was rooted but had a locked bl. My apps and messages were all there but the radio was different. I'd understand if I was going from ICS to JB but I was on JB both times. The only difference being a locked BL. It's got to be something about the Radio from p760 or V20B that didn't work on my earlier backup or something like that because the layout status bar is different with a "data" button and showing H instead of 4g(which are the same afaik).
Since, I restored to my backup from after my bootloader unlock and root so data is working showing 'H' with the different layout
Also, I had problems backing up and restoring until I noticed that it works better when I power off the phone and do the manual commands to enter recovery as opposed to using the app to send me to recovery(where I incurred /system backup errors).
My last question is which cwm recovery should I use? I currently have the one for a locked bootloader installed as per Artas182x's website. On that post he has a link for an unlocked bootloader recovery on the xda forums but that thread was updated to not working. Are there any disadvantages to me using a locked bootloader cwm recovery?
I don't think I have any option but to try it as I want to flash CM10.1 for p769. I also read that if your bootloader is unlocked, you can download the cwm from the googleplay. If this is true, can I just install over or should I uninstall the Artas182x locked bootloader one????
update: have to remove l9 recovery by deleting the appropriate system folders and then flash the appropriate .img through adb commands
Help.
shockah486 said:
I realized I misread your question. When I flashed before the incident, it failed to write to system and I didn't restore my other folder. I rebooted and it was all missed up. Anyway, now that I've got everything back and now with an unlocked bootloader, i was able to recover my old image. However, data isn't working so I have to find the radio to flash as I recall reading in other threads.
Can someone explain in laymen terms why this is? recap, i was on unlocked bl rooted jb and I flashed my old cwm backup when I was rooted but had a locked bl. My apps and messages were all there but the radio was different. I'd understand if I was going from ICS to JB but I was on JB both times. The only difference being a locked BL. It's got to be something about the Radio from p760 or V20B that didn't work on my earlier backup or something like that because the layout status bar is different with a "data" button and showing H instead of 4g(which are the same afaik).
Since, I restored to my backup from after my bootloader unlock and root so data is working showing 'H' with the different layout
Also, I had problems backing up and restoring until I noticed that it works better when I power off the phone and do the manual commands to enter recovery as opposed to using the app to send me to recovery(where I incurred /system backup errors).
My last question is which cwm recovery should I use? I currently have the one for a locked bootloader installed as per Artas182x's website. On that post he has a link for an unlocked bootloader recovery on the xda forums but that thread was updated to not working. Are there any disadvantages to me using a locked bootloader cwm recovery?
I don't think I have any option but to try it as I want to flash CM10.1 for p769. I also read that if your bootloader is unlocked, you can download the cwm from the googleplay. If this is true, can I just install over or should I uninstall the Artas182x locked bootloader one????
update: have to remove l9 recovery by deleting the appropriate system folders and then flash the appropriate .img through adb commands
Click to expand...
Click to collapse
Although I might be late, I have the same problem and the same phone and I really need help. I have a soft bricked phone lg optimus l9 and I had the same problems that you had exactly... Which is weird exept I don't have Clock Work Mod or anything ... If you get this I would really appreciate some help. Thanks
yup me too
I finally got software upgrade to work with my lg p769 that was security error cuz i still haven't unlocked the bootloader, if i knew what a good job lg and T-Mobile did in locking it i would have waited and got a g3 that my buddy rooted in like 5 min and unlocked the boot....
What worked for me is this LG FLASH TOOL 2014 THREAD ON XDA
http://forum.xda-developers.com/showthread.php?t=2797190
flashed both the 20H and 20D successfully i uninstalled everything lg in the control panel first though.
Hope this works for you cuz i was struggling on and off for a month to get this far lol
the 2014 tool ultimately worked for me too, once I fixed a couple things. I had rooted and forgotten to unlock, so it was at Security Error, and it would also disconnect at 15% .. in the 2014 tool, I had to install all the updates even though I'm in windows 7 or it would keep doing it. All good now.
I have been trying all these methods and I am still not able to get in the S/W upgrade mode. The only thing I am getting from the device is being able to put it fastboot mode (The inverted one). I really want to revive this phone
Thanks in advance for any help given
Liger878 said:
I have been trying all these methods and I am still not able to get in the S/W upgrade mode. The only thing I am getting from the device is being able to put it fastboot mode (The inverted one). I really want to revive this phone
Thanks in advance for any help given
Click to expand...
Click to collapse
Hey, it's been ages since I have done any of this but IIRC, if you can get into fastbood mode u can still get into software mode,
- turn phone into fastboot mode
- open the software upgrader thing as you normally do
- maybe switch emerg to diag or something like that
- this part is where it's slightly different than the normal way(same program but u select a different option than the default 1st option on
I think if yoiu look through the tutorials it does mention an alternative method for getting into software mode
in one instance in my past, i had to reflash the ICS boot drivers so the software installer would recognize that
the flashing of the ICS boot drivers is done through fastboot. Should be a post in my history where I asked a question regarding this.
Sorry for the chaos but maybe this will help you get in the right direction since I don't know any of your phone history and what you've done etc
best of luck mate
shockah486 said:
Hey, it's been ages since I have done any of this but IIRC, if you can get into fastbood mode u can still get into software mode,
- turn phone into fastboot mode
- open the software upgrader thing as you normally do
- maybe switch emerg to diag or something like that
- this part is where it's slightly different than the normal way(same program but u select a different option than the default 1st option on
I think if yoiu look through the tutorials it does mention an alternative method for getting into software mode
in one instance in my past, i had to reflash the ICS boot drivers so the software installer would recognize that
the flashing of the ICS boot drivers is done through fastboot. Should be a post in my history where I asked a question regarding this.
Sorry for the chaos but maybe this will help you get in the right direction since I don't know any of your phone history and what you've done etc
best of luck mate
Click to expand...
Click to collapse
Thanks, Never tried switching to DIAG before but I will try it and let you know what is the outcome.
Hopefully you find the thread that states the exact steps bc that is off the top of my head and over a year ago by memory . GL bud
Liger878 said:
Thanks, Never tried switching to DIAG before but I will try it and let you know what is the outcome.
Click to expand...
Click to collapse
Hey, I have been trying it with the fastboot but it keeps timing out and not allowing me to finish. One thing I should let you know is that, ever since I had put the device in fastboot, I am not able to get back the S/W upgrade mode. Dont know if that will help in seeing what my problem is or if you want me to explain everything from the beginning again, I am more than happy to.
Have you followed the steps that I linked to in the first 3 posts of this thread?
Follow the steps to flash the ICS bootloaders in fastboot and then you can do the fastboot trick for getting the software to recognize your device.
Right now your phone has the JB boot loader on it and is thus not recognized by the software.
recap:
step 1: flash the ICS bootloaders in fastboot (look at the linked thread in post 2)
step 2: use the software in emerg or diag mode but sitll follow the same steps as the tutorial. I think my earlier posts should explain precisely.
if you dont flash the ICS bootloaders, it won't be recognized by the KDZ installer
Looking to start a discussion on rooting the unlocked version.
I have tried the root for other variants for this phone and does not work
hi would love to see my k8+ rooted. i have the lmx210ulma version mtk and android 7.1.2.
There are recoveries for this phone and i have a full partition dump i nade today using salt on my ubuntu 18.04 machine. when i say full i mean something like 30-50 .img files pulled.
Any way. The problem on my end is booting into fastboot mode or rebooting to the bootloader. i have tried ADB, recovery and key combinations with out ever getting there. I can however get the phone to download into recovery download mode just fine.
any help would be appreciated
https://forum.xda-developers.com/an...atek-armv8-t3922213/post79626434#post79626434
Duhjoker said:
hi would love to see my k8+ rooted. i have the lmx210ulma version mtk and android 7.1.2.
There are recoveries for this phone and i have a full partition dump i nade today using salt on my ubuntu 18.04 machine. when i say full i mean something like 30-50 .img files pulled.
Any way. The problem on my end is booting into fastboot mode or rebooting to the bootloader. i have tried ADB, recovery and key combinations with out ever getting there. I can however get the phone to download into recovery download mode just fine.
any help would be appreciated
Click to expand...
Click to collapse
We are now in this forum. Why some dork mod moves these too early?
Why here, why not to the K8 forums instead?
The link I posted should work with your device...
Just got told to go to the k8 forums because im really just trying to get the bootloader unlocked. Temp root is nice but my plans involve a recovery and a fully rooted phone. Im trhing to develop a way to compile apps and operating systems completely on the device but i need full access.
Im looking for firmware for LG K8 2018 X210ULMG. Where can i find it ?
go to google and type in "LG K8 + LMX210ULM stock rom" you will get at least five pages or more.
Duhjoker said:
go to google and type in "LG K8 + LMX210ULM stock rom" you will get at least five pages or more.
Click to expand...
Click to collapse
I can't fin anywhere for X210ULMG. Try and when you will find paste here link because anywhere is this rom.
which android version do y0u have 9n your k8. I also need you to go to settings system software info and tell me the software versiion. And just for SandG no seriously, open up a terminal in terminal emulator and type getprop. im looking fir the value of
ro.lge.swversion_arb
to be of further assistance may i ask what exactly you are using it for? ie reflash stock fix brick or other. i can help you with the best plan of action and any other how to.
If you are still out there the ULMG and ULM are the same device. There is no ULMG stock rom. So you will need to flash your K8+ using the ULM firmware. If you are looking to roll back to get to the bootloader the lowest version you can find is a letter F version. None so far have an ARB value so happy flashing.
I myself own this device and its an easily rootable phone with bootloader unlock. Just flash the kdz with the lowest letter value then adb reboot bootloader and then in fastboot mode use fastboot oem unlock and your free to flash any cv1 device twrp recovery.img to the phone.
Just make sure to use either carliv image kitchen or android image studio to check and make sure that system, syatem.img, are both ext4 in recovery.fstab. System.img will probably be labled emmc which will cause failure to mount. Also cache and data as well. Firmware/modem should be labled as vfat. Just as if they were labled if you looked at original fstab.
To root just extract boot.img from kdz and patch using magisk and flash using fastboot flash boot boit.img then fastboot flash recovery recovery.img When booting into twrp first time flash no verity opt encrypt and make backup. Upon exiting make sure all parts are mounted or twrp loop will occur.
Duhjoker said:
If you are still out there the ULMG and ULM are the same device. There is no ULMG stock rom. So you will need to flash your K8+ using the ULM firmware. If you are looking to roll back to get to the bootloader the lowest version you can find is a letter F version. None so far have an ARB value so happy flashing.
I myself own this device and its an easily rootable phone with bootloader unlock. Just flash the kdz with the lowest letter value then adb reboot bootloader and then in fastboot mode use fastboot oem unlock and your free to flash any cv1 device twrp recovery.img to the phone.
Just make sure to use either carliv image kitchen or android image studio to check and make sure that system, syatem.img, are both ext4 in recovery.fstab. System.img will probably be labled emmc which will cause failure to mount. Also cache and data as well. Firmware/modem should be labled as vfat. Just as if they were labled if you looked at original fstab.
To root just extract boot.img from kdz and patch using magisk and flash using fastboot flash boot boit.img then fastboot flash recovery recovery.img When booting into twrp first time flash no verity opt encrypt and make backup. Upon exiting make sure all parts are mounted or twrp loop will occur.
Click to expand...
Click to collapse
I have problem because one month ago I flashed My K8 ULMG with kdz for Aristo 2 . I downloaded the software from Aristo 2 and made Brick through it.
Now it doesn't turn on, gives no sign of life, nothing. When connected to a laptop, the computer can only see Qualcomm HS-USB QDLoader 9008.
Do you know solution for it ?
There are two versions of the k8+ a qualcomm version and an mtk version. Did you read my post after your last reply. I was trying to help you determine that sort 0f thing.
As for a fix.... no as of currently there is no fix for either the qc or mtk versions once bricked. i am working on possible solutions but those are not going to be any time soon.
Your best bet at this point is to look for a used and damaged phone and replace the board in your phone with a different board. Find a k8+ lm-x210ulm or an aristo 2 board. They are cheap around $20 us and can be found with broken screens. They have no arb values so can be flashed and downgraded to get the boot loader unlocked and reflashed and upgraded after with guidance.
Dont feel to bad it happens. I have 4 boards that are trash but im still gonna try to unbrick them. But please what ever you do dont do it with out guidance. pm if you need and ill help.
Duhjoker said:
There are two versions of the k8+ a qualcomm version and an mtk version. Did you read my post after your last reply. I was trying to help you determine that sort 0f thing.
As for a fix.... no as of currently there is no fix for either the qc or mtk versions once bricked. i am working on possible solutions but those are not going to be any time soon.
Your best bet at this point is to look for a used and damaged phone and replace the board in your phone with a different board. Find a k8+ lm-x210ulm or an aristo 2 board. They are cheap around $20 us and can be found with broken screens. They have no arb values so can be flashed and downgraded to get the boot loader unlocked and reflashed and upgraded after with guidance.
Dont feel to bad it happens. I have 4 boards that are trash but im still gonna try to unbrick them. But please what ever you do dont do it with out guidance. pm if you need and ill help.
Click to expand...
Click to collapse
Did you found some method for unbrick this phone without motherboard change ?