Related
Hey..After getting my esn added I can't seem to get the apn settings to stick.I do have talk & text but no internet whatsoever.I would really appreciate some help if somebody is willing to lend a helping hand..Thanks
Seems like there's no one with a photon on metro
I am also on Metro with text,talk,3G. But no MMS yet (I don't use it as much anyway).
Follow this link see if you can get your 3G to work.
http://forum.xda-developers.com/showthread.php?p=8395950#post8395950
There are differences in getting Photon to work with 3G. So some of the steps indicated in the above link are different. And I assume that you know how to get your MSL number. Here are the differences:
1. You don't need HTC diag drivers. This should be Motorola driver.
2. In order to get to diag mode. You need to boot into boot loader and choose BP tools
3. You will need to get QPST_2.7_366
4. Once you got everything:
follow step 9 - 28. However at step 22, instead of choosing "Simple IP", you want to choose "MOB+Simple IP". Otherwise 3G will not work.
Once done you should have 3G. However there is an annoying error Mobile IP Registration will be in your notification (ignore this, it does not matter).
Finally!!! I got it to work.I wasn't changing the spc code that's why it was giving me a problem.Thanks man & as soon as I figure out this mms thing imma let u know
Have you been able to get mms? if so, will you explaing how? thanks...
eltano07 said:
Have you been able to get mms? if so, will you explaing how? thanks...
Click to expand...
Click to collapse
Are you on a custom rom?
I have mms working fine sending and receiving on AOKPCB
GhostxLawliet said:
Are you on a custom rom?
I have mms working fine sending and receiving on AOKPCB
Click to expand...
Click to collapse
Can you please help me a little more about that...how to get the custom rom you mentioned for example, also how to install it would me helpfull...will I loose all my info when doing it? THANKS IN ADVANCE...
eltano07 said:
Can you please help me a little more about that...how to get the custom rom you mentioned for example, also how to install it would me helpfull...will I loose all my info when doing it? THANKS IN ADVANCE...
Click to expand...
Click to collapse
I pm'd you
I'm having trouble programming the phone.I started up my phone in bp tools but my phone doesnt seem to show up.
Is there certain drivers im suppose to install? i used the drivers from the main site because i couldn't find any other place to dl the drivers.
Are you on a gingerbread ROM ? If not then you should be.Double check your drivers & see if the phone pops up under ports in device manager.Once it shows up & gives you a port number then its a go.QPST & CDMA workshop is all you need
Im currently running cm7 and its on 2.3.7
In ports i see motorola QC Diag Port (COM8)
When i connect to COM8 with cdma workshop it becomes unresponsive (crash?)
connecting through qpst i see COM8 also but it reads as no phone.
Also thank you for your help so far!
U need to be on a blur ROM or else CDMA WS is gonna be unresponsive.Use rocko rom or any blur rom then retry
My mopho doesnt seem to pick up on metropcs i did the above and had my esn added to metro
not sure what went wrong.
EDIT: i got my internet working through dfs using the provision settings up top but my phone calls and text aren't sending/recieving
any luck with mms with aokp 4.0?
Hey everyone,
After finally getting my S3 I wanted to check out some stuff in QPST, but I can't seem to get the phone to be properly recognized by the program.
I was able to use the dialer code *#7284# to get into PhoneUtil but I'm not exactly sure what to do from there. It won't let me set UART to modem and I'm not sure which option to set it to under "USB," but I was able to get the computer and QPST to recognize the phone as modem-serial thingy in a COM port.
QPST sees it but a question mark shows up under the phone column and I can't see anything for it in "service programming."
Thanks in advance!
Which version or company is you're gs3 from... I used ##3424# brought me to phone utl. chose first option cdma modem, I haven't tried qpst but read somewhere that 266v is the one to use.. I will update with you in a few to let you know if I was able to connect and read phone!
Use the debug + modem setting, you can read phone and get some info but Not the akey with cdma workshop. That is obtained another way...........
Thanks, this was before I tried CDMA Workshop, which actually works.
It would be nice getting it to work in QPST too, though...
Sent from my SPH-L710 using xda app-developers app
What version of CDMA Workshop did you use?
z4k said:
What version of CDMA Workshop did you use?
Click to expand...
Click to collapse
I'm on vacation so I can't go home and tell you and I don't remember, sorry.
Sent from my SPH-L710 using xda app-developers app
The only on I can get to recognize the Slll is QPST 2.7 Built 3.74 but when you try to read it, it stops in the middle of it and gives an error message.
cdma ws sees/reads, but i suspect the drivers arent correct because only limited functionality with that program
I was able to read the nv items 465, 466, 1192, and 1194 using efs browser in QPST 2.7 Build 378 setup on a Windows XP machine. Then I used CDMA Workshop 3.8.0 to change what I needed to change.
grimmace4 said:
I was able to read the nv items 465, 466, 1192, and 1194 using efs browser in QPST 2.7 Build 378 setup on a Windows XP machine. Then I used CDMA Workshop 3.8.0 to change what I needed to change.
Click to expand...
Click to collapse
not verizon though right? also, what settings did you have for usb? debug modem? ty
need help please! so on cdma workshop i did a nv items read from a galaxy s2 from sprint the range in dec from 0 to 4122 range in hex 0 to 101A then I wrote those nv items to my galaxy s3 now my signal goes on and off and cant make any calls please if someone can tell me what to do or if you can dump the memory on the nv items so i can restore my phone would highly appreciate it.
jbrolo said:
need help please! so on cdma workshop i did a nv items read from a galaxy s2 from sprint the range in dec from 0 to 4122 range in hex 0 to 101A then I wrote those nv items to my galaxy s3 now my signal goes on and off and cant make any calls please if someone can tell me what to do or if you can dump the memory on the nv items so i can restore my phone would highly appreciate it.
Click to expand...
Click to collapse
wouldnt that include the personal info? why didnt you backup that range before writing to it?
I know I was dumb for not doing that i did a backup on CW thinking that backup would include those files but tried to go back to that backup and still having the same issue signal goes on and off couple seconds after phone resets by itself unless i put it on airplane mode
Ok folks. If you are like me, you searched all over the web didnt find a definitive answer on how to go about getting your HTC rezound to Pageplus.
I bought a used Rezound. It came with NO Verizon SIM card. No software updates to it. I read a lot, sounded like getting to the latest stock was a good idea as it usually fixes issues. Well, I promptly updated to the leaked global ICS rom. Go the rom from android police dated Aug 15.
So my rezound had locked stock global ICS rom, no SIM card. Here is how i flashed it to pageplus. Please follow the steps as mentioned, as i have stumbled too many times and got it working.
================================
Not a must but...
1. Dont upgrade your phone to ICS rom if you dont want to root your phone. As ICS blocks APN updates. Meaning if you need 3g on pageplus or any other carrier and you dont want to root your phone, dont upgrade. If you dont mind rooting your phone, you can just ignore this warning.
Requirements:
MIN and MDN Information:
You can get MIN and MDN by calling pageplus or follow steps below.
goto http://www.kittywireless.com/pageplus/phonestatusform.html
right at the bottom you can enter email and phone number. You will get an email with MIN and MDN information.
OS Requirement:
Windows 7 64bit or 32bit. No support for Linux, Mac or XP(??).
Software you will need:
1. HTC Sync http://www.htc.com/us/support/htc-rezound-verizon/software-updates.
2. HTC Diag drivers. You can download from below.
3. QPST. http://conflipper.com/Software/QPST_2.7_366.rar
4. CDMA Workshop. You need the full version. Demo is not useful. There is an old 2.7 cracked version floating around in the web. That will do the job.
Steps to follow:
1. Install HTC Sync. This software will install HTC Sync and HTC Drivers. All you are looking for is HTC Drivers. So, as soon as installation is complete you can uninstall HTC Sync alone. They have seperate uninstallers.
2. Install HTC Diag drivers. Now, i hope you have access to Windows 7. These drivers didnt install in XP for me. it could work for you.
This step is crucial, without these drivers installed you wont be able to do anything.
i. Connect your phone to PC.
ii. Just leave it on charge mode. The HTC drivers you installed in previous step should recognize the phone.
iii. Goto the dialer in phone. dial ##3424. press call. This should put the phone in DM mode.
iv. Win 7 will try to find the drivers and fail. If you open the device manager (or short cut just run devmgmt.msc), you should see the
2 devices with no drivers. HTC DIAG and HTC DIAG 9K.
v. double click on HTC Diag and click upgrade drivers. You need to manually upgrade the drivers..
http://forum.xda-developers.com/showthread.php?t=697487 This guide does a very good job. I dont want to repeat it. You can look at it if you are stuck. Just look at the driver installation part alone.
vi. Just ignore the HTC Diag 9k for now.
3. You have done a major step already. (I got stuck on step 2 for quiet sometime.). Install cdma workshop(CDMAWS). This software will trip anti-virus software(AV). So, just turn-off AV( or add CDMAWS in your AV's exclusion list). Apparently CDMAWS does use the virus technique to work but it is not malicious.
i. connect the phone to PC and dial ##3424 for DM mode. Find out which COM port your phone is using to connect.
ii. start CDMAWS. Select the COM port you phone uses. click connect. These should be in the topline of the GUI.
iii. if you are connected. The status bar at the bottom of window should indicate it. If everything is fine, click read(it should be next to connect/disconnect button). If everything is working so far, lots of empty spaces will be populated with data.
iv. switch to the Security tab. look for a spc button. enter "000000" in the text box above it(dont include quotes). This is the password for EPST. click spc -> spc send. you should see a pop-up saying phone unlocked. (if you are using this guide for Sprint phones, you need to obtain this password). Verizon just leaves it unlocked.
v. goto 'other' tab. look for RU-IM. click on the drop-down box. Select "NV-only". This option will be present only in full version.
vi. if you have not downloaded the attachment on this post, do it now. Now focus your attention on PRL box in the same tab as in step v.
PRL stands for preferred raoming list. I have attached 2 prl files. For me the 51720-evdo.prl gave roaming sign. I used 52711.prl, it worked fine. Click on write and choose 52711.prl from you download directory. It should write, the information to your phone.
vii. next switch to NAM tab. Enter the MIN you got from the email you got from kitty wireless (link is provided above). You can also get that info from pageplus by calling. MDN is nothing but your cell number. Enter that in dir or directory text box. click write.
4. you are done with CDMAWS. you can reboot your phone. At this point, if you havent changed ESN with pageplus do so now. You can do ESN change through online chat at pageplus website. It is free.
5. If you see roaming sign on your rezound, you need to use a different PRL. Roaming is indicated by a small triangle above the signal bars. start CDMAWS and select a different PRL file to write to your phone(steps 3(i) - 3(vi)). If everything is fine, from you rezound, call *22890 to program your phone. You can also use *22801 to program. if after a short pause it says unable to program your phone. It failed to program. Make sure you followed all the steps. If after a long pause it says unable to program. you have succeeded in getting the phone registered with pageplus. Now you should have your phone working for Voice and SMS/texting.
6. Take a deep breath and pat yourself, you have achieved a major step. Now to program 3g part. As i said before, if you are having locked stock ICS rom, you wont be able to go further. ICS doesn't let changing APNs. GB is fine with changing APNs. I havent rooted my ICS. i am just happy with a working Voice and SMS for my needs. Wifi satisfies my need.
7. Fire up QPST configuration.
i. Click on "Add New Port..." Select the port your device is on. It should be same as in CDMAWS.
ii. On the next screen highlight your device.
iii. Click on "Start Clients--Service Programming"
iv. Click 'Read From phone" When the prompt pops up click "OK"
v. Now tab over to "M.IP"
vi. In the drop down below that says simple ip+Mobi change that to "Simple IP"
vii. Now double click on "Profile 2"
viii.In the "NAI" section put your phone [email protected]
ix. In the "tetheredNAI" section put your phone [email protected]
x. For the IP Address put 255 all the way across for the last two sections and leave the 0's in the first section and Click OK
xi. Now click on "PPP config"
xii. Click "Um"
xiii. In the box that says "User ID", Enter your phone [email protected]
xiv. Click in the box that says "Tethered NAI", Enter your phone [email protected]
xv. Click in the box that says "Password", Enter "vzw"
xvi. Click the "AN" tab, User ID is your phone [email protected] and Password is "vzw"
xvii. Click "write to phone"
8. Power your phone down then reboot it.
9. i. Connect to wifi
ii. Open market
iii. Search for "APN Backup and Restore" and install. If you have GB, this will work on it own. Now if you have a rooted ICS, you can use Titanium Backup pro to run this system app. ICS allows system apps to modify APNs.
iv. Open APN and click Backup APN's
v. Now put your phone in "airplane mode"
vi. Click "delete apn's"
vii. Click "restore apn"
viii. Select page plus apn from below
ix. Disable Airplane Mode
x. Reboot
And thats it your fully flashed with MMS, Talk, Text, 3G
Credit goes to lots of folks. Mainly to Nevell, techwerkz, folks at howard forums and scores of others who are not mentioned.
Hope this helps a few folks.
Great guide.
hey guys, im kinda new to this and im planning to switch from VM to PP. I am plannng to buy the HTC Rezound. When i buy it, do i have to buy the contract version or the "month to month" version on the verizon site?? And does this tutorial actually work? Can anyone confirm it? And i dont care about 3g or 4g so i just want talk and text/
vwade79 said:
hey guys, im kinda new to this and im planning to switch from VM to PP. I am plannng to buy the HTC Rezound. When i buy it, do i have to buy the contract version or the "month to month" version on the verizon site?? And does this tutorial actually work? Can anyone confirm it? And i dont care about 3g or 4g so i just want talk and text/
Click to expand...
Click to collapse
Im thinking of selling mine soon. PM me if your interested.
Sent from my Nexus 7 using Tapatalk 2
I got 3G data working on stock ICS 4.0.3.605.1
To make it work you need to write all necessary settings to the 9K port as well. The tricky part is that QPST will not work and you have to use full paid version of CDMA Workshop or DFS (free version is ok) instead.
Repeat steps 3 and 4 of javamaan's guide for port 9k and use DFS for step 7.
Go to Programming/Data. Fill all fields in PAP, PPP, HDR AN, HDR AN Long and HDR AN PPP boxes. Set HDR SCP force AT config to RevA_MFPA. Uncheck eHRPD enabled. Go to Mobile IP and set NAI to [email protected].
When writing, make sure that it actually writes the data. Enable full logging and see if green "nv item written ok" messages appear. Ignore offline-d errors.
For more detailed instructions, see this cricket flashing guide.
You also need to have any sim card inserted to enable Mobile network Off/On switch in settings and get rid of the annoying message on the lock screen.
APN settings have no effect in CDMA mode. I've never touched APN menu and data works just fine.
The only thing it might be necessary is MMS, but I've never bothered to set it up.
Hello all,
For the life of me, I can't get sms or 3g to work. I've gone over this tutorial over and backwards and even did the cricket tut.
My rezound is on GB. I downgraded it with the official, stock, OTA or what ever you want to call it GB. I'm rooted but not custom ROM. I just got rid of the bloatware.
I have PPC service. Thanks, that part was great! There is a "write" line missing in the RU IM part, but I figured it out. Voice and simple text work but no sms. I even copied my wife's apn from her cell, but still, no go.
OK, done with my rant. Just had to let it out. So my steps:
in QPST - wrote everything to 8K as stated above, to the "t"
-I did come up with an error, but checked it in DFS and everything was there.
in DFS - wrote everything to 9k as stated above, to the "t"
Found the apn file from another thread because it is missing in this one. Did a restore, and.....nothing.
Found the apn settings from another site and entered it in manually......nothing.
Copied my wife's apn settings...nothing.
Made myself a drink...at least I have a good buzz going...check my phone...nothing...DOHHH!
What do I do now???
Cheers!
AsianCajun said:
Hello all,
For the life of me, I can't get sms or 3g to work.
Click to expand...
Click to collapse
As already mentioned above, forget about the APNs! They are not used for CDMA mode (except MMS). Until you have 3G data, just leave the default VZWINTERNET APN as it is.
You don't need to downgrade to GingerBread. I've done everything on ICS 4.0.3.605.1, but 4.0.3.605.2 should work as well.
Make sure you've actually written everything to both ports. Especially 9K port. Read back and check if all values are there (except passwords that can't be read). Read PRL and make sure that version is 51720.
Post your screenshots of DFS after you read the data (NAM/PRL, Data and MobileIP pages).
OK, I wrote the prl over again and opened up DFS and wrote to nam1 and nam2.
Well, I was able to get it to work. I put ics back on, updated to one of the newer prl's and put a sim chip. I'm not sure what did the trick, but my bet is on the chip. note* I used an old at&t sim chip that I had laying around. I still get the warning on the lock scene, but that doesn't bother me. Thanks again to those who made these tuts.
Cheers
Im getting close to getting my Rez up on PP,... (deleted)
EDIT: Thanks so much for this thread, Im well on my way, with a few bumps along the way while I learn the software and phone. was stuck at step 5 til I realized you did the programming and dont need the #22890. with or w/o my new sim, I can make & receive calls/texts. Im barred from the ota programming by the phone.
Now I'm figuring out qpst as to why it doesnt show profile 2, just a single profile (0). So I dont know if I should modify that profile 0... And I need to get rid of the error message re the 4g activation. So i'm a little ways from having any data functioning... going to bed, sleepy and cross-eyed...
"Activating your phone..."
In the lock screen, how do you remove the irritating "Activating your phone..." message. I have everything working except MMS, but I don't care about it, I just want the stupid notification gone.
I also have an LTE card installed. I had remotesquaD flash it for me...
HTC Rezound on PagePlus no 3G data
javamaan said:
Ok folks. If you are like me, you searched all over the web didnt find a definitive answer on how to go about getting your HTC rezound to Pageplus.
I bought a used Rezound. It came with NO Verizon SIM card. No software updates to it. I read a lot, sounded like getting to the latest stock was a good idea as it usually fixes issues. Well, I promptly updated to the leaked global ICS rom. Go the rom from android police dated Aug 15.
So my rezound had locked stock global ICS rom, no SIM card. Here is how i flashed it to pageplus. Please follow the steps as mentioned, as i have stumbled too many times and got it working.
================================
Not a must but...
1. Dont upgrade your phone to ICS rom if you dont want to root your phone. As ICS blocks APN updates. Meaning if you need 3g on pageplus or any other carrier and you dont want to root your phone, dont upgrade. If you dont mind rooting your phone, you can just ignore this warning.
Requirements:
MIN and MDN Information:
You can get MIN and MDN by calling pageplus or follow steps below.
goto http://www.kittywireless.com/pageplus/phonestatusform.html
right at the bottom you can enter email and phone number. You will get an email with MIN and MDN information.
OS Requirement:
Windows 7 64bit or 32bit. No support for Linux, Mac or XP(??).
Software you will need:
1. HTC Sync http://www.htc.com/us/support/htc-rezound-verizon/software-updates.
2. HTC Diag drivers. You can download from below.
3. QPST. http://conflipper.com/Software/QPST_2.7_366.rar
4. CDMA Workshop. You need the full version. Demo is not useful. There is an old 2.7 cracked version floating around in the web. That will do the job.
Steps to follow:
1. Install HTC Sync. This software will install HTC Sync and HTC Drivers. All you are looking for is HTC Drivers. So, as soon as installation is complete you can uninstall HTC Sync alone. They have seperate uninstallers.
2. Install HTC Diag drivers. Now, i hope you have access to Windows 7. These drivers didnt install in XP for me. it could work for you.
This step is crucial, without these drivers installed you wont be able to do anything.
i. Connect your phone to PC.
ii. Just leave it on charge mode. The HTC drivers you installed in previous step should recognize the phone.
iii. Goto the dialer in phone. dial ##3424. press call. This should put the phone in DM mode.
iv. Win 7 will try to find the drivers and fail. If you open the device manager (or short cut just run devmgmt.msc), you should see the
2 devices with no drivers. HTC DIAG and HTC DIAG 9K.
v. double click on HTC Diag and click upgrade drivers. You need to manually upgrade the drivers..
http://forum.xda-developers.com/showthread.php?t=697487 This guide does a very good job. I dont want to repeat it. You can look at it if you are stuck. Just look at the driver installation part alone.
vi. Just ignore the HTC Diag 9k for now.
3. You have done a major step already. (I got stuck on step 2 for quiet sometime.). Install cdma workshop(CDMAWS). This software will trip anti-virus software(AV). So, just turn-off AV( or add CDMAWS in your AV's exclusion list). Apparently CDMAWS does use the virus technique to work but it is not malicious.
i. connect the phone to PC and dial ##3424 for DM mode. Find out which COM port your phone is using to connect.
ii. start CDMAWS. Select the COM port you phone uses. click connect. These should be in the topline of the GUI.
iii. if you are connected. The status bar at the bottom of window should indicate it. If everything is fine, click read(it should be next to connect/disconnect button). If everything is working so far, lots of empty spaces will be populated with data.
iv. switch to the Security tab. look for a spc button. enter "000000" in the text box above it(dont include quotes). This is the password for EPST. click spc -> spc send. you should see a pop-up saying phone unlocked. (if you are using this guide for Sprint phones, you need to obtain this password). Verizon just leaves it unlocked.
v. goto 'other' tab. look for RU-IM. click on the drop-down box. Select "NV-only". This option will be present only in full version.
vi. if you have not downloaded the attachment on this post, do it now. Now focus your attention on PRL box in the same tab as in step v.
PRL stands for preferred raoming list. I have attached 2 prl files. For me the 51720-evdo.prl gave roaming sign. I used 52711.prl, it worked fine. Click on write and choose 52711.prl from you download directory. It should write, the information to your phone.
vii. next switch to NAM tab. Enter the MIN you got from the email you got from kitty wireless (link is provided above). You can also get that info from pageplus by calling. MDN is nothing but your cell number. Enter that in dir or directory text box. click write.
4. you are done with CDMAWS. you can reboot your phone. At this point, if you havent changed ESN with pageplus do so now. You can do ESN change through online chat at pageplus website. It is free.
5. If you see roaming sign on your rezound, you need to use a different PRL. Roaming is indicated by a small triangle above the signal bars. start CDMAWS and select a different PRL file to write to your phone(steps 3(i) - 3(vi)). If everything is fine, from you rezound, call *22890 to program your phone. You can also use *22801 to program. if after a short pause it says unable to program your phone. It failed to program. Make sure you followed all the steps. If after a long pause it says unable to program. you have succeeded in getting the phone registered with pageplus. Now you should have your phone working for Voice and SMS/texting.
6. Take a deep breath and pat yourself, you have achieved a major step. Now to program 3g part. As i said before, if you are having locked stock ICS rom, you wont be able to go further. ICS doesn't let changing APNs. GB is fine with changing APNs. I havent rooted my ICS. i am just happy with a working Voice and SMS for my needs. Wifi satisfies my need.
7. Fire up QPST configuration.
i. Click on "Add New Port..." Select the port your device is on. It should be same as in CDMAWS.
ii. On the next screen highlight your device.
iii. Click on "Start Clients--Service Programming"
iv. Click 'Read From phone" When the prompt pops up click "OK"
v. Now tab over to "M.IP"
vi. In the drop down below that says simple ip+Mobi change that to "Simple IP"
vii. Now double click on "Profile 2"
viii.In the "NAI" section put your phone [email protected]
ix. In the "tetheredNAI" section put your phone [email protected]
x. For the IP Address put 255 all the way across for the last two sections and leave the 0's in the first section and Click OK
xi. Now click on "PPP config"
xii. Click "Um"
xiii. In the box that says "User ID", Enter your phone [email protected]
xiv. Click in the box that says "Tethered NAI", Enter your phone [email protected]
xv. Click in the box that says "Password", Enter "vzw"
xvi. Click the "AN" tab, User ID is your phone [email protected] and Password is "vzw"
xvii. Click "write to phone"
8. Power your phone down then reboot it.
9. i. Connect to wifi
ii. Open market
iii. Search for "APN Backup and Restore" and install. If you have GB, this will work on it own. Now if you have a rooted ICS, you can use Titanium Backup pro to run this system app. ICS allows system apps to modify APNs.
iv. Open APN and click Backup APN's
v. Now put your phone in "airplane mode"
vi. Click "delete apn's"
vii. Click "restore apn"
viii. Select page plus apn from below
ix. Disable Airplane Mode
x. Reboot
And thats it your fully flashed with MMS, Talk, Text, 3G
Credit goes to lots of folks. Mainly to Nevell, techwerkz, folks at howard forums and scores of others who are not mentioned.
Hope this helps a few folks.
Click to expand...
Click to collapse
Hello everyone, I am new to this forum and first thing I want to do is thank everyone for their time and effort of putting the useful information on this forum! Also thanks to javamaan, I have been able to activate my HTC Rezound (previously on Verizon) on PagePlus. I have the following working: Talk, TXT, MMS, and 1X data. But no matter what I do, (spent over a week on this now, no kidding) I can't get 3G working.
I have the original Verizon 4GLTE sim card installed.
I am S-OFF, rooted, running leaked android 4.0.3 (4.03.605.3). (QPST is only good for 8K port)
I use mostly CDMAWS 3.8.7 demo and DFS 4.0.0.5 to manipulate data.
I write same data values to 8K and 9K ports, to NAM1 and NAM2.
Could it have something to do with HA and AAA shared secret values? some say leave it blank, some say 'vzw' (in hex), some say need to get those off of a donor phone.....
Could it be that when writing any passwords in DFS for 9K port they don't seem to showup/stick?
Thank you!
-snpiee
Wileyworld said:
Im getting close to getting my Rez up on PP, but am stuck on (step 5) since I cant dial out to program phone
Click to expand...
Click to collapse
I never could get *228xx activation to work. Just filled all data manually.
You can try to insert some other sim card, like AT&T or whatever. It just wants to have something in the slot.
@ Wileywold:
Step 5 is just if you get the triangle by the signal bars. *228 in any form will give you that error. I followed yura's directions and programmed for the mms and 3g using DFS.
@ snpiee:
On my phone HA is 300 and AAA is 2. Like you, I don't know if that has anything to do with programming or not. I've tried different prls and still can't get 3g to show up. I'm also stuck on 1x.
snpiee said:
Could it have something to do with HA and AAA shared secret values? some say leave it blank, some say 'vzw' (in hex), some say need to get those off of a donor phone.....
Click to expand...
Click to collapse
You definitely don't need a donor phone. As I recall, I did "vzw". Actually, all that Mobile IP NAI stuff is not used if "Simple IP only" is selected.
Also, someone suggested to do a software reset with 4G SIM inside after writing all values. Not sure if it really helps, but you can try.
snpiee said:
Could it be that when writing any passwords in DFS for 9K port they don't seem to showup/stick?
Click to expand...
Click to collapse
Passwords don't show up when I read back after writing, so this is OK.
Check PRL version and other stuff.
---------- Post added at 10:10 PM ---------- Previous post was at 09:59 PM ----------
AsianCajun said:
I've tried different prls and still can't get 3g to show up. I'm also stuck on 1x.
Click to expand...
Click to collapse
Oh, I thought you finally got 3G... I will go make my DFS screenshots now, so we can compare.
I just updated my prl to 52874 hoping it would point my Rez to 3g towers. Well, I'm still on 1x.
Screenshots of 9K port. I've highlighted some important items.
I finally got it. I wrote to both 8K and 9K ports and NAM1 and NAM2. All values were the same. My prl is the most recent verizon from my area, which is 52874. Here are the screen shots.
Thanks again to yura and javamaan for their hard work!
AsianCajun said:
I finally got it. I wrote to both 8K and 9K ports and NAM1 and NAM2. All values were the same. My prl is the most recent verizon from my area, which is 52874. Here are the screen shots.
Thanks again to yura and javamaan for their hard work!
Click to expand...
Click to collapse
You got 3G working now? I will compare your values to mine when I get home today....
Thanks for posting DFS screenshots!
By the way in your pics you use PrefMobileIP not SimpleIP is that correct?
Yura80 said: "Screenshots of 9K port. I've highlighted some important items."
Thanks for kindly sharing help here! I continue to tinker with this by lurking here and (after success with voice/texts/1x data) I'm now working on getting the 3g operating, and the dfs screen shots are very helpful. I want to upload a few for someone to see, and point me closer to my goal. Ive tried to imitate yours, but im running dfs 3.1.xxx and there are a few differences in the location of items, and labeled a bit different. I had to guess at one of the places to insert the dun info since it didnt show quite the same layout of lines/descriptions.For example, PAP has an extra line called data, while the PPP section has 1 less line , so I tried the dun line in that PAP section.
I'm very close to having this thing DONE and I never would have gotten here without great tutors right here!
BTW, What do you use to get the great screen shots to insert here in the forum?
after i brick my razr xt908 CDMA and i looking for stock firmware HERE
finaly i get it and unbrick my device and work ok ,, thanks for mr dullawolf
I insisted my device xt908 work on gsm networks and i try again after flash with dullawolf firmware
make root with EPRJ_EasyRootICS_MultiOS_v1.5 and use Radiocomm to active GSM Networks
finaly all done i can use any gsm on my xt908
http://www.droidrzr.com/index.php/topic/24630-xt908-boot-failure/
MA7MOD_GSM said:
after i brick my razr xt908 CDMA and i looking for stock firmware HERE
finaly i get it and unbrick my device and work ok ,, thanks for mr dullawolf
I insisted my device xt908 work on gsm networks and i try again after flash with dullawolf firmware
make root with EPRJ_EasyRootICS_MultiOS_v1.5 and use Radiocomm to active GSM Networks
finaly all done i can use any gsm on my xt908
http://www.droidrzr.com/index.php/topic/24630-xt908-boot-failure/
Click to expand...
Click to collapse
do you care to elaborate a little bit more on how you did this? i have the same phone on the same sbf lol but it doesnt get service on my straight talk sim card i tried changing it to gsm using *#*#4636#*#*
He is in Cairo, Egypt and that is why it works for him.
This phone has the same or similar blocks of US GSM carriers as the XT912 Razr it appears.
oman14 said:
do you care to elaborate a little bit more on how you did this? i have the same phone on the same sbf lol but it doesnt get service on my straight talk sim card i tried changing it to gsm using *#*#4636#*#*
Click to expand...
Click to collapse
simply root device and active gsm using radiocomm
To make it work just download Radiocomm 11.12.2 from here: RadioComm_v11.12.2_Install.zip , after this connect the phone to the pc and select pc mode.
In radiocomm go to ma/common/mdm 6x00
go to settings/usb/pst usb drivers
switch to ftm common 1 and wait for the phone to make it purple or green
on the upper side in NVAcces got to value 1877 NV_RF_BC_CONFIG_I
Read the value from the device and after that replace first 16 digits with: 8703E804000200
write data back and restart.
u need setup apn setting for your carrier:good:
MA7MOD_GSM said:
simply root device and active gsm using radiocomm
To make it work just download Radiocomm 11.12.2 from here: RadioComm_v11.12.2_Install.zip , after this connect the phone to the pc and select pc mode.
In radiocomm go to ma/common/mdm 6x00
go to settings/usb/pst usb drivers
switch to ftm common 1 and wait for the phone to make it purple or green
on the upper side in NVAcces got to value 1877 NV_RF_BC_CONFIG_I
Read the value from the device and after that replace first 16 digits with: 8703E804000200
write data back and restart.
u need setup apn setting for your carrier:good:
Click to expand...
Click to collapse
i figured thats what u ment i tried that but it didnt work im in the us by the way. that is probably why
i send pm for u
MA7MOD_GSM said:
i send pm for u
Click to expand...
Click to collapse
Hi MA7MOD_GSM, you seem to be the only hope for unlocking GSM on the XT908.. I also have a US-based XT908 (bought by accident on eBay -- seems to be from Appalachian carrier in US).
I tried Radiocomm with your guidance above, but no luck... I can't get this thing to respond properly on Radiocomm at all.
I am so confused, trying to learn the details of Android phones... could a ROM activate GSM on this thing ??? or does it have to be done first at the low level on Radiocomm ? What mode does the phone have to be in to allow Radiocomm to communicate with it ???
This is my 1st post here, I registered just to see if I can figure this out... I feel like I got burned bad, I expected an XT912 to arrive....
Wanted to bump and see if there is any new info on us based xt908 getting gsm
help for xt908 alltel unlocked
oman14 said:
do you care to elaborate a little bit more on how you did this? i have the same phone on the same sbf lol but it doesnt get service on my straight talk sim card i tried changing it to gsm using *#*#4636#*#*
Click to expand...
Click to collapse
i tried that method and it shows smsc error.plrease help me i'm from india.
Hello
i need help in rediocmm , my phone is rooted but when i conenct phone with usb there is no PC mode ,
i tried all 3 " mass storage , MTP , PTP " option but not able get this
switch to ftm common 1 and wait for the phone to make it purple or green
Click to expand...
Click to collapse
can please any one help how to get it
HI , Thanks For instruction its work ,
but after it Done we got Voice issue in Speakers . is any one else face this issue ?
You Are Superb. Bro.
MA7MOD_GSM said:
simply root device and active gsm using radiocomm
To make it work just download Radiocomm 11.12.2 from here: RadioComm_v11.12.2_Install.zip , after this connect the phone to the pc and select pc mode.
In radiocomm go to ma/common/mdm 6x00
go to settings/usb/pst usb drivers
switch to ftm common 1 and wait for the phone to make it purple or green
on the upper side in NVAcces got to value 1877 NV_RF_BC_CONFIG_I
Read the value from the device and after that replace first 16 digits with: 8703E804000200
write data back and restart.
u need setup apn setting for your carrier:good:
Click to expand...
Click to collapse
Keep it up you are really the master.
Thanks and thanks again.
glad to see u done
thanks
Radiocomm
mohsin-* said:
HI , Thanks For instruction its work ,
but after it Done we got Voice issue in Speakers . is any one else face this issue ?
Click to expand...
Click to collapse
how did you get radiocomm to communicate with your phone?
Hello Bro
MA7MOD_GSM said:
after i brick my razr xt908 CDMA and i looking for stock firmware HERE
finaly i get it and unbrick my device and work ok ,, thanks for mr dullawolf
I insisted my device xt908 work on gsm networks and i try again after flash with dullawolf firmware
make root with EPRJ_EasyRootICS_MultiOS_v1.5 and use Radiocomm to active GSM Networks
finaly all done i can use any gsm on my xt908
http://www.droidrzr.com/index.php/topic/24630-xt908-boot-failure/
Click to expand...
Click to collapse
bro link is not working pllllzzz help me
Najeeb Baba said:
bro link is not working pllllzzz help me
Click to expand...
Click to collapse
which link you need bro?
First off, thanks for tolerating this somewhat noobish post, but I've searched through almost the whole internet trying to find answers.
Alright, so here's the dealio.
Sprint Galaxy Note 3. UICC unlocked via idoneapp, then used on domestic T-Mobile through GCF settings. I want to enable more bands as described in the following links: here and here.
I get as far as Step 9 in the second link. Then, I go to select a port, and it's not there. OK, so I uncheck the "diagnostic port only" check box, and select COM12 which is what my phone is on. No big deal, right? So I go to read/backup my NV and I start it; it only gets to 12% and says "Could not Communicate in Diagnostic Mode"
That's it. I've tried different USB ports, different USB cables, other USB modes on the phone, I even have a custom kernel. I really hope it's something obvious that I'm doing wrong instead of something that's a niche error.
Thanks, guys.
I ended up being able to read the LTE bands with DFS and write them with QXDM. The only thing is that there is no LTE/GSM/UMTS mode on the phone, so it's either LTE/CDMA or GSM/UMTS for now until I figure out if I can flash some other ROM to it to let it use the other bands, cause right now it only wants to look at band 25.
So I've been trying to flash the N900T MI7 modem/baseband on my N900P but I can never get it to flash in Odin. I've been able to put the modem and non-hlos in flash able zips and flash those but it never shows up. I've also tried to dd the files directly but that doesn't work either. Ideas?
I am impressed it's not bricked yet.
Sent from my SM-G935F using XDA-Developers mobile app
Same issue
BlockOfDynamite said:
First off, thanks for tolerating this somewhat noobish post, but I've searched through almost the whole internet trying to find answers.
Alright, so here's the dealio.
Sprint Galaxy Note 3. UICC unlocked via idoneapp, then used on domestic T-Mobile through GCF settings. I want to enable more bands as described in the following links: here and here.
I get as far as Step 9 in the second link. Then, I go to select a port, and it's not there. OK, so I uncheck the "diagnostic port only" check box, and select COM12 which is what my phone is on. No big deal, right? So I go to read/backup my NV and I start it; it only gets to 12% and says "Could not Communicate in Diagnostic Mode"
That's it. I've tried different USB ports, different USB cables, other USB modes on the phone, I even have a custom kernel. I really hope it's something obvious that I'm doing wrong instead of something that's a niche error.
Thanks, guys.
Click to expand...
Click to collapse
I am facing same issue regarding back up nv at 12%
vipsy6 said:
I am facing same issue regarding back up nv at 12%
Click to expand...
Click to collapse
So basically what happened was I found a couple other tools to do what I wanted. First was DFS tool. This works well, because it can both read and write bands to the nv of the phone. I forget what the second was, but it could both read and write the raw value of any given value in the nvram. I'll have to dig through my stuff again if you want to know what the second program was. The fact of the matter is that I was never able to get it working right. The phone always looked at band 25 LTE no matter what bands I turned on/off of the phone.
another ?
BlockOfDynamite said:
So basically what happened was I found a couple other tools to do what I wanted. First was DFS tool. This works well, because it can both read and write bands to the nv of the phone. I forget what the second was, but it could both read and write the raw value of any given value in the nvram. I'll have to dig through my stuff again if you want to know what the second program was. The fact of the matter is that I was never able to get it working right. The phone always looked at band 25 LTE no matter what bands I turned on/off of the phone.
Click to expand...
Click to collapse
Please let me know second program
BlockOfDynamite said:
First off, thanks for tolerating this somewhat noobish post, but I've searched through almost the whole internet trying to find answers.
Alright, so here's the dealio.
Sprint Galaxy Note 3. UICC unlocked via idoneapp, then used on domestic T-Mobile through GCF settings. I want to enable more bands as described in the following links: here and here.
I get as far as Step 9 in the second link. Then, I go to select a port, and it's not there. OK, so I uncheck the "diagnostic port only" check box, and select COM12 which is what my phone is on. No big deal, right? So I go to read/backup my NV and I start it; it only gets to 12% and says "Could not Communicate in Diagnostic Mode"
That's it. I've tried different USB ports, different USB cables, other USB modes on the phone, I even have a custom kernel. I really hope it's something obvious that I'm doing wrong instead of something that's a niche error.
Thanks, guys.
Click to expand...
Click to collapse
hi
how did you connect QPST to your phone? i can't do it,
installed QPST under windows 7, QDXM and kies, but in QPST configuration i get "No Phone" when added new port
walidham said:
hi
how did you connect QPST to your phone? i can't do it,
installed QPST under windows 7, QDXM and kies, but in QPST configuration i get "No Phone" when added new port
Click to expand...
Click to collapse
I never did get QPST to connect to my phone. I think I was able to get it to see the phone at some point, but it would never read anything from it or write anything to it. The program always froze up or something when I tried that. If I could remember the second program I used, I'd share it with you all, but for the life of me, I can't think of it.
Edit: Oh hey, the two programs I used are RIGHT IN MY SECOND POST. lol. Yeah, use DFS tool to read the NV and QXDM to write the NV. It'll save you a whole lot of trouble over doing stuff with QPST.
BlockOfDynamite said:
I never did get QPST to connect to my phone. I think I was able to get it to see the phone at some point, but it would never read anything from it or write anything to it. The program always froze up or something when I tried that. If I could remember the second program I used, I'd share it with you all, but for the life of me, I can't think of it.
Edit: Oh hey, the two programs I used are RIGHT IN MY SECOND POST. lol. Yeah, use DFS tool to read the NV and QXDM to write the NV. It'll save you a whole lot of trouble over doing stuff with QPST.
Click to expand...
Click to collapse
Hi
Yes i used only DFS tools and it work fine, also and changed my Bands 4G and 3G to work in Europe with Spint N900P phone,
3G work fine but not 4G, i will install custom Rom and see if it will work.
walidham said:
Hi
Yes i used only DFS tools and it work fine, also and changed my Bands 4G and 3G to work in Europe with Spint N900P phone,
3G work fine but not 4G, i will install custom Rom and see if it will work.
Click to expand...
Click to collapse
Well, 3G will work fine without changing anything anyway. All of the bands are already enabled. 4G is the issue.
BlockOfDynamite said:
Well, 3G will work fine without changing anything anyway. All of the bands are already enabled. 4G is the issue.
Click to expand...
Click to collapse
Yes 4G is the big pb, i found that DFS Tools write 3G bands but for LTE, the issue is in BC Config Div, need SPC code
i tried to find SPC /MSL code but no chance
I will install SPR-N900PVPUBMJ4 rom and after SPR-N900PVPUBMJ3 modem and use DSF tools to set it 000000
hope i will work
walidham said:
Yes 4G is the big pb, i found that DFS Tools write 3G bands but for LTE, the issue is in BC Config Div, need SPC code
i tried to find SPC /MSL code but no chance
I will install SPR-N900PVPUBMJ4 rom and after SPR-N900PVPUBMJ3 modem and use DSF tools to set it 000000
hope i will work
Click to expand...
Click to collapse
Flash the MI3 (that's emm eye three) modem and then use the app included in the zip file to find the MSL code. Here's a link to the zip file: http://bit.ly/1oZDO9t
I was not aware that you could change the MSL code with DFS tools. At least I have a Verizon Note 3 now, so I have a lot more LTE bands than the Sprint version does (although I don't care all that much; I think I may switch to the Nexus 6 soon). But yeah, try the stuff in the zip file from the link, and you should be able to
Find your MSL code
Unlock your phone internationally
Use hidden menus
Most of all, have fun! I know for sure this can be very very frustrating a lot of the time, but if you don't have fun, then I don't think there's much profit in trying stuff like this. Good luck!
BlockOfDynamite said:
Flash the MI3 (that's emm eye three) modem and then use the app included in the zip file to find the MSL code. Here's a link to the zip file: http://bit.ly/1oZDO9t
I was not aware that you could change the MSL code with DFS tools. At least I have a Verizon Note 3 now, so I have a lot more LTE bands than the Sprint version does (although I don't care all that much; I think I may switch to the Nexus 6 soon). But yeah, try the stuff in the zip file from the link, and you should be able to
Find your MSL code
Unlock your phone internationally
Use hidden menus
Most of all, have fun! I know for sure this can be very very frustrating a lot of the time, but if you don't have fun, then I don't think there's much profit in trying stuff like this. Good luck!
Click to expand...
Click to collapse
After many try, finaly i get my MSL code (24 hours).
I have downgrad my phone to 4.4.2, and install custom rom Galaxy-Note-fre3-2.26,
and after using adb and logcat i got my code.
Now how can i activate it for internationally ? i have added all LTE band (3,7,20) but still H+
I will try with QXDM, but i have windows 10 and give me error acces denied.
walidham said:
After many try, finaly i get my MSL code (24 hours).
I have downgrad my phone to 4.4.2, and install custom rom Galaxy-Note-fre3-2.26,
and after using adb and logcat i got my code.
Now how can i activate it for internationally ? i have added all LTE band (3,7,20) but still H+
I will try with QXDM, but i have windows 10 and give me error acces denied.
Click to expand...
Click to collapse
I just did it with my Verizon Note 3 on Windows 10, so I know it's not a Windows 10 issue. Also, QPST seemed to work with my Verizon phone but not my Sprint phone. Weird. Make sure you're running QXDM as administrator. Also, I unlocked all of the LTE bands in this way but I can't seem to get LTE from my GSM sim card, even by going into the service mode and enabling all LTE bands.
BlockOfDynamite said:
I just did it with my Verizon Note 3 on Windows 10, so I know it's not a Windows 10 issue. Also, QPST seemed to work with my Verizon phone but not my Sprint phone. Weird. Make sure you're running QXDM as administrator. Also, I unlocked all of the LTE bands in this way but I can't seem to get LTE from my GSM sim card, even by going into the service mode and enabling all LTE bands.
Click to expand...
Click to collapse
Yes; for LTE i found in hiddn menu, that they use Tri Bands (25, 26 & 41), so for others bands will not work.
I don't know how i can disable this and force it to use bands 3, 7 20.
walidham said:
Yes; for LTE i found in hiddn menu, that they use Tri Bands (25, 26 & 41), so for others bands will not work.
I don't know how i can disable this and force it to use bands 3, 7 20.
Click to expand...
Click to collapse
I honestly couldn't tell you, and I'm not sure how much help I'm going to be in general. I've tried it on both of my Note 3 phones but have had no confirmed success. Sprint especially is the one carrier that sticks out like a sore thumb, and by association, so do their phones. I've had plenty of frustration on that front, that's for sure.
BlockOfDynamite said:
I honestly couldn't tell you, and I'm not sure how much help I'm going to be in general. I've tried it on both of my Note 3 phones but have had no confirmed success. Sprint especially is the one carrier that sticks out like a sore thumb, and by association, so do their phones. I've had plenty of frustration on that front, that's for sure.
Click to expand...
Click to collapse
Thanks for your help,
Just one question if have any idea for it
can i install Firmware N9005 using PIT file for N90005 in N900P?
Because when i received my phone(from china) , the first time i see that BaseBand version is for n9005 and phone name n900 but in download mode i see n900p
i think chines have a method to do it
walidham said:
Thanks for your help,
Just one question if have any idea for it
can i install Firmware N9005 using PIT file for N90005 in N900P?
Because when i received my phone(from china) , the first time i see that BaseBand version is for n9005 and phone name n900 but in download mode i see n900p
i think chines have a method to do it
Click to expand...
Click to collapse
Maybe. Really they have a method to do anything I would advise against trying to do that, although I'm not sure what harm it could do if you can still get back into download mode. I've tried flashing different versions' firmware to the N900P with no success.