headphone jack issues - Verizon Samsung Galaxy Note II

Hey all
Recently started having issues with my headphone jack and was looking to see if ppl had any suggestions. I tried cleaning it (lubricant from radioshack) and while it improved somewhat problem is still there. The issue I have is if I am using a pair of headphones without a mic channel it seems to be to loose and any tap I lose audio and it goes to speaker or the music pauses.
Auxillary cable in the car is extremely sensitive...
Trying to see if anybody has a suggestion before replacing device

oz1421 said:
Hey all
Recently started having issues with my headphone jack and was looking to see if ppl had any suggestions. I tried cleaning it (lubricant from radioshack) and while it improved somewhat problem is still there. The issue I have is if I am using a pair of headphones without a mic channel it seems to be to loose and any tap I lose audio and it goes to speaker or the music pauses.
Auxillary cable in the car is extremely sensitive...
Trying to see if anybody has a suggestion before replacing device
Click to expand...
Click to collapse
OK first off, from having first hand experience with sensitive electronics, never use lubricant to clean anything. Use isopropyl alcohol. I do also believe that you should think about purchasing a cable with a mic channel, or try wrapping a small piece of aluminum foil around the plug, should be a quick fix. But it does sound like you have a loose solder connection in the headphone jack. Might be something I would look into getting warranty replaced if the isopropyl doesnt work. You can put it on a q-tip and clean it like that. Isopropyl will evaporate and leave absolutley no residue. and its what the military uses to clean electronics.

Do you have a case on? Because one case I have makes mine finiky in my truck but just because the case kind of makes the cable not go allll the way in...without a case mine is fine though

@ cornettbr
should have clarified i didn't spray it directly into the jack - u spray it on the headphone plug part and wipe it down - it basically cleans this and helps clean the contacts - saw it on a youtube video - no actual liquid touches the contacts but in anycase it didn't work
- i tried alcohol also a failure...
@ s10sdeville
yeah regardless of having the case on or off it still does it... really sucks
i know i might sound crazy but i ended up getting a replacement piece for the headphone jack on ebay
took the phone apart yesterday and it is pretty easy (no warranty stickers either - surprised me) - i rather do this than dealing with a refurb have had some personal bad experiences.

Did that work for you?
Sent from a really big phone.

cornettbr said:
Did that work for you?
Sent from a really big phone.
Click to expand...
Click to collapse
the part isn't going to be in for a couple of days

got the part in today
swapped it and it is good as new - took maybe 20 minutes to do the whole thing
for anyone that is willing to try this in the future remember patience - the most pita part is putting the main board back in without catching ribbon cables on the bottom of it.

oz1421 said:
got the part in today
swapped it and it is good as new - took maybe 20 minutes to do the whole thing
for anyone that is willing to try this in the future remember patience - the most pita part is putting the main board back in without catching ribbon cables on the bottom of it.
Click to expand...
Click to collapse
Nice. Should have taken some pics and threw up a guide incase someone need it in the future.
Sent from the dark on a Note 2

kintwofan said:
Nice. Should have taken some pics and threw up a guide incase someone need it in the future.
Sent from the dark on a Note 2
Click to expand...
Click to collapse
i used a video on youtube from LE55ONS - he had one of the better quality videos on what needed to be done.

oz1421 said:
i used a video on youtube from LE55ONS - he had one of the better quality videos on what needed to be done.
Click to expand...
Click to collapse
Even better
Sent from the dark on a Note 2

Related

My SGS2 Vibrate is messed up!

So it happened this morning when my alarm went off and it vibrated. I heard a plastic part vibrating also. The sharp loud noise was disgusting. I shut off my alarm thikning it was my cheap SGP case.
Later today I played around trying to find out if the silicone had a hole or something where the plastic frame was touching the SGS2 phone itself. Nope. I took the whole case off. Each time it vibrates it sounds like... ahh what the hell. I will film it for you guys now.
http://www.youtube.com/watch?v=_GoIrBmMC1U
WTF is that? I took the cover off. I took the SIM card out on another occasion too. It sounds like something on the upper left. If I push my finger down on the panel, it stops. If you notice the few seconds it is sitting on the table flat, it's fine. Just a little weight seems to calm it down. Not sure if its the vibrating motor itself because it is vibrating properly. Sounds like something is loose inside though...
Anyone experienced this before? Should I go for RMA?
Second part of the question:
Obviously being an XDA-er I'm rooted. I will flash back to stock and unroot. I bought this off of Expansys-USA so I should get *some* reasonable attempt by them to send it back. What are the chances that my warranty gets denied? I don't have a USB jig to reset the counter, but I'll of course get rid of the yellow triangle.
*grrrr... I need to dig up my Nexus S now if I have to go through warranty... I'm guessing I'll be phoneless for weeks*
I don't know if it would invalidate the warrenty or not (technically rooting/custom roms is supposed to), but when I had a problem with my stereo jack not working rather than risking it I just replaced the part myself.
The vibration motor, stereo jack and earphone speaker are all on the same part.
(I got it from this guy on ebay for about $7 if you're curious.)
Random6 said:
I don't know if it would invalidate the warrenty or not (technically rooting/custom roms is supposed to), but when I had a problem with my stereo jack not working rather than risking it I just replaced the part myself.
The vibration motor, stereo jack and call speaker are all on the same part.
(I got it from this guy on ebay for about $7 if you're curious.)
Click to expand...
Click to collapse
I see. I'm not sure whats broken really. When I shake my SGS2 I hear something rattling inside. I'm just afraid to open the thing up... is it difficult?
Just watched your video. It sort of sounds as if somehow the vibration motor came loose from its proper spot and is now moving around vibrating against the plastic. Its normally held in with some adhesive (basically double sided tape) within a cutout area.
When I had mine apart I actually took a photo, http://i.imgur.com/fgN9F.jpg, if that makes it any more clear.
I actually recorded the process of me reinstalling the new part (excluding the disassembly, there are lots of clips of that from other people on youtube) but havent gotten around to uploading it yet since my internet connection sucks and the file is nearly 2GB.
Edit to add:
No it wasn't really all that difficult to dissassemble, it was actually pretty easy. That said I enjoy taking things apart and trying to fix them. This was the first time I've dissassembled anything as small as a cell phone, but I'm used to taking things apart and trying to fix them when they break. If you don't have any experience taking apart electronics you might want to think twice or just pay someone who fix's cell phones to do it.
If you're thinking about it, heres a video where someone shows taking it apart to get a rough idea of whats involved.
http://www.youtube.com/watch?v=QKztg1ra4-0
I decided to try and upload the video I took, once it finishes (in about 2.5 hours) it should be viewable here:
www.youtube.com/watch?v=-ud1upGzLBs
Random6 said:
I decided to try and upload the video I took, once it finishes (in about 2.5 hours) it should be viewable here:
www.youtube.com/watch?v=-ud1upGzLBs
Click to expand...
Click to collapse
thank you for your detailed writeup. im going to try this. ive taken apart my macbook pro to install an SSD before, and a few other electronics, but i'm not the very best (i feel clumsy sometimes), but i'm willing to give this a shot.
The only thing I'm worried about is that I could potentially mess up the phone in other ways in disassembly such that my warranty won't be honored if I need to resort to that... We'll see tonight. It looks like you used two screwdrivers? Which ones will I need? I have a #000 that I see will be needed for the back plate at least...
k. opened my phone up.
i just took the screws out and the backplate. i pushd around to make sure things are tight, and they seem to be.
put it together and the vibrate thing happens VERY rarely now..
I shook my phone around and still heard something shaking (please tell me if this happens).
I opened up my phone and the camera module seems to be loose. Is it supposed to be glued down?
Just to let you know, you say you don't have a USB jig so your Flash counter may make your warranty void, but, if you flash to an ice cream sandwich ROM (Cyanogenmod 9) you can install an app called 'Triangle Away' which will basically get rid of the Flash count and yellow triangle - it needs root by the way. (search it up on XDA, it's by chainfire')
Then you can flash stock and send in for warranty.
Sent from my GT-I9100 using XDA
dmo580 said:
k. opened my phone up.
I shook my phone around and still heard something shaking (please tell me if this happens).
I opened up my phone and the camera module seems to be loose. Is it supposed to be glued down?
Click to expand...
Click to collapse
I don't remember it being glued down. Its been a few month since I fixed mine but if I recall correctly it just fit snugly in place between some plastic fitted walls.
This is the camera module you mean right?
Edit: I also don't hear anything shaking with mine, did you mabe leave a screw loose inside?
Random6 said:
I don't remember it being glued down. Its been a few month since I fixed mine but if I recall correctly it just fit snugly in place between some plastic fitted walls.
This is the camera module you mean right?
Edit: I also don't hear anything shaking with mine, did you mabe leave a screw loose inside?
Click to expand...
Click to collapse
Yeah. Camera module. That's the one. The main 8MP shooter. It's not glued down or anything. It shakes around inside. I definitely did not leave a screw inside because I only opened the back panel and I put all the screws back in.
It's weird because something making noise while shaking the phone has been documented here:
http://forum.xda-developers.com/showthread.php?t=1254520
And I noticed that when you activate camera it goes away. Quite strange but as an engineer this makes me wonder HOW that even happens? Shrug.
I'm waiting for my Samsung Focus S phone to come from the Windows Phone challenge and I'm contemplating using that for a month while my i9100 goes out for warranty. Of course I can always use my Nexus S as a backup, but part of me wants to force myself on a new platform for a month and see how that goes... Hahahaha.
Random6 said:
No it wasn't really all that difficult to dissassemble, it was actually pretty easy.
Click to expand...
Click to collapse
Hey Random6, did you happen to find that after replacing the vibrator motor with a new one, the intensity is now less than when new? I used double sided tape, but with 1.5mm, I guess the motor won't vibrate AT ALL.
Also I found that if I don't screw the one that seems to be closest to the vibrator motor all the way in, it obviously vibrates harder, but not hard enough.
I also used two very thin copper plates to sandwich the motor between the plastic plates, but once again, that was too much and the vibrations were not transfered to the phone's body, but I could hear it doing its job.
Any suggestions?
Thanks!

Microphone... Does it just not work for standalone use?

I have not been able to have any calls where the person is able to hear me properly. Is this a lost cause?
The mic works fine, clear and with good volume, on mine. There might be some white sealant clogging up the mic pinhole on yours. There was on mine, but I removed it carefully while cleaning the sim slot. If you are not really careful, you can puncture the seal at the back of the mic pinhole, destroying any hope your watch would have of surviving even a brief immersion, so you have to be really careful !
Sent from my Nexus 7 using Tapatalk
Thanks...that is helpful. I seem to have poor quality on phone calls and Google search, but reasonable on the voice record function. What did you clean it with? From the outside or inside (back off)? Any advice was helpful...I was considering puncturing the seal in hopes of improving sound!
That might actually help, but probably is unnecessary and is irreversible. I am glad I did not puncture the seal.
I cleared mine out when I first got it, back really early in February with a sewing needle. I had to clean the sim slot out anyway because the same stuff was spilled or overflowed into it so I couldn't get my T-Mobile micro sim to seat. I cleaned it with a bright light shining into the hole from the outside and did not open the back. I was able to pry out of the pinhole a couple of mm of the white stuff that seemed to be almost completely blocking the pinhole, then I noticed a grayer flat material at the back of the hole and stopped then.
Mic works flawlessly now, still, for all uses. Even my mother can understand me clearly when I use the TrueSmart as a standalone phone w/o headphones (though BT headphones work too). OK Google is as accurate as on my Nexus devices, which is pretty accurate. Good luck, and proceed with caution.
Sent from my Nexus 7 using Tapatalk
trent999 said:
That might actually help, but probably is unnecessary and is irreversible. I am glad I did not puncture the seal.
I cleared mine out when I first got it, back really early in February with a sewing needle. I had to clean the sim slot out anyway because the same stuff was spilled or overflowed into it so I couldn't get my T-Mobile micro sim to seat. I cleaned it with a bright light shining into the hole from the outside and did not open the back. I was able to pry out of the pinhole a couple of mm of the white stuff that seemed to be almost completely blocking the pinhole, then I noticed a grayer flat material at the back of the hole and stopped then.
Mic works flawlessly now, still, for all uses. Even my mother can understand me clearly when I use the TrueSmart as a standalone phone w/o headphones (though BT headphones work too). OK Google is as accurate as on my Nexus devices, which is pretty accurate. Good luck, and proceed with caution.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Okay that was miraculous! Followed your suggestion and used a sewing needle to remove any white stuff down the mic hole, and it went from crackly mess to crystal clear call quality just like that. Thanks for the suggestion.
Uh-huh ! Really good. Told you so, Mr. Lokifish !
(You were right about the seal though. I had missed that...)
Sent from my Nexus 5 using Tapatalk
umm... you guys are all removing the sealant? half of it? based on Lokifish photo there is maybe 2mm of it. Do you care about "water resistant"? I am not going to use a needle on it... I hope the firmware gets fixed. Thanks all.
trent999 said:
That might actually help, but probably is unnecessary and is irreversible. I am glad I did not puncture the seal.
I cleared mine out when I first got it, back really early in February with a sewing needle. I had to clean the sim slot out anyway because the same stuff was spilled or overflowed into it so I couldn't get my T-Mobile micro sim to seat. I cleaned it with a bright light shining into the hole from the outside and did not open the back. I was able to pry out of the pinhole a couple of mm of the white stuff that seemed to be almost completely blocking the pinhole, then I noticed a grayer flat material at the back of the hole and stopped then.
Mic works flawlessly now, still, for all uses. Even my mother can understand me clearly when I use the TrueSmart as a standalone phone w/o headphones (though BT headphones work too). OK Google is as accurate as on my Nexus devices, which is pretty accurate. Good luck, and proceed with caution.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
What's the "white" stuff you mention. Sealant? I haven't come across any of this on my EU 1/8/2100 version. Is it visible at all from the outside on the mic slot as I don't see it at all. I would adjust it but everyone I've spoken to with my device can hear me perfectly so I probably won't play around with it.
DaBountyHunter said:
What's the "white" stuff you mention. Sealant? I haven't come across any of this on my EU 1/8/2100 version. Is it visible at all from the outside on the mic slot as I don't see it at all. I would adjust it but everyone I've spoken to with my device can hear me perfectly so I probably won't play around with it.
Click to expand...
Click to collapse
You would see it if you removed the back plate - it is the stuff used to seal where the antennas run through the watch body into the band.
Sometimes the worker assembling a particular TrueSmart got sloppy and the same stuff winds up fouling the sim slot or the mic pinhole or both. If it is blocking the mic pinhole, the audio picked up can sound to someone hearing your voice on a call muffled or garbled. Carefully cleaning out the mic pinhole without damaging the special plastic seal at the very back end of it can immensely improve the mic audio quality.
Since your mic pinhole is clear, there is no reason to stick a needle in there ! Also, your mic seems to be working fine already, which makes sense because its pinhole is not plugged by sloppy assembly work.
If you don't see that the pinhole is blocked inside up to near the surface with white stuff, and your mic is working fine, you don't have this problem that many others do have.
Sent from my Galaxy Nexus using Tapatalk
trent999 said:
You would see it if you removed the back plate - it is the stuff used to seal where the antennas run through the watch body into the band.
Sometimes the worker assembling a particular TrueSmart got sloppy and the same stuff winds up fouling the sim slot or the mic pinhole or both. If it is blocking the mic pinhole, the audio picked up can sound to someone hearing your voice on a call muffled or garbled. Carefully cleaning out the mic pinhole without damaging the special plastic seal at the very back end of it can immensely improve the mic audio quality.
Since your mic pinhole is clear, there is no reason to stick a needle in there ! Also, your mic seems to be working fine already, which makes sense because its pinhole is not plugged by sloppy assembly work.
If you don't see that the pinhole is blocked inside up to near the surface with white stuff, and your mic is working fine, you don't have this problem that many others do have.
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
I haven't opened up the back yet so was wondering if this was visible from the outside of the watch! Thanks for letting me know what to look for though
Yes, you can see it, if its there, by shining a bright light into that pinhole from the outside, but it's hard to tell if what you are seeing is really the flat plastic seal that is supposed to be there at the very back end, a mm or two inside, or if it is really blocking debris !
You don't want to damage that real seal ! Its all the way through the body at the back, though.
In my case, the misapplied white sealant had pretty nearly filled the pinhole to the outer edge. It came out as a little mm long plug, using a needle and tweezers.YMMV...
Sent from my Galaxy Nexus using Tapatalk
Yeah ok I've definitely got nothing of the sort then from observing the outside. Looks like it's more a QA issue with the build quality. Also I almost had a minor heart attack I scrapped the screen face of my watch along a metal frame. I thought sh*t it's scratched it. Went to look at screen in the light NOTHING. Still perfect so I'm glad to report the Sapphire Glass does it's job. Haven't worn a watch in years I got to remember not to walk too close to walls etc! :silly:
trent999 said:
The mic works fine, clear and with good volume, on mine. There might be some white sealant clogging up the mic pinhole on yours. There was on mine, but I removed it carefully while cleaning the sim slot. If you are not really careful, you can puncture the seal at the back of the mic pinhole, destroying any hope your watch would have of surviving even a brief immersion, so you have to be really careful !
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Thanks trent999, after cleaning out the mic pinhole on my truesmart the mic actually works pretty good now.:good:
The Omate Truesmart project in theory was a terrific idea, and had it implemented, marketed, produced under quality control, and supported the product I believe it could have been the beginning of good things to come for Omate.
But instead Omate simply bungled badly their first project to the point I think it's reputation is so damaged Omate will simply fade into the sunset. Such a shame.
Had it not been for the support of all the individual xda developers hours of thankless support of this device most of the truesmarts would be now residing in landfills.
Again thanks trent999 and a BIG SHOUT OUT THANK YOU to everyone at xda who supported this project.

Broken earpiece?

Hi,
my P9000 just arrived today i wanted to try it out. After the update to 20160419 i wanted to make a call but there were no sound. With my headset everything works just fine, but without there is no call possible due to no sound. Is that maybe a software-bug or is the earpiece speaker broken?
I hope i don't have to send it back
Tank you!
pansenkoenig said:
Hi,
my P9000 just arrived today i wanted to try it out. After the update to 20160419 i wanted to make a call but there were no sound. With my headset everything works just fine, but without there is no call possible due to no sound. Is that maybe a software-bug or is the earpiece speaker broken?
I hope i don't have to send it back
Tank you!
Click to expand...
Click to collapse
Factory reset, if it doesn't help flash stock ROM again and report
Both did not help unfortunately. Any other advice than sending it in? I heard tomrepair.de here in germany is not quite good (8-10 weeks repair time and no change in the problem). Are there any other repair Centers? Can i do it by my own? Whrer can I buy spare parts?
The same for me... Sometimes it works suddenly
new7 said:
The same for me... Sometimes it works suddenly
Click to expand...
Click to collapse
Well, then it's maybe a loose/cold connection. I would open the phone by myself and take a look at it, but i don't want to loose warranty
I just wait, if i can get a new one.
pansenkoenig said:
Well, then it's maybe a loose/cold connection. I would open the phone by myself and take a look at it, but i don't want to loose warranty
I just wait, if i can get a new one.
Click to expand...
Click to collapse
It is soldered to board with wire. Broken my today when trying to removing it Hope they release soon replacement parts like earpiece, camera, screen etc.
http://i.imgur.com/JjF9qGI.jpg
It is definitely software related.
In the end I send the phone back to the reseller and got my money back. Because it is nearly impossible to send a smartphone from Germany to China, i was allowed to remove the battery for the shipping. Now I'm a happy Honor 5x user.
I think the battery is still working (unless i damaged it by removing it, it is really good glued), so if anyone is in need for it, i could sell it.
For anyone that might be still interested and ends up here... I just repaired the (previously broken) earpiece of my Elephone P9000. It is not too difficult to do yourself, but you definitely need patience, precision, a steady hand, good eyes and some tools. Here is wat I did. By the way, I first tried a factory reset, which did not help me. But you never know...
I ordered a replacement earpiece via AliExpress. This cost me less than €8, and the part arrived within 12 days. Not bad.
I watched a P9000 repair video on YouTube to prevent making big mistakes/damage by opening the phone. I my case, the flatcable to the power and volume buttons was glued to the back of the phone, so I used this part as a hinge to open the back like a door.
I unscrewed the plastic cover that covers the motherboard (5 screws). It still has a couple of hooks, but with some prying it will come loose. Caution as the flatcable to the fingerprint sensor is attached to the board, so use this (again) as a hinge and flip the cover over from top to bottom.
There is flatcable that partially covers the earpice (at the top middle, soldere with two mini-leads, black & red). I could easily fold this a bit back. Wit a small screwdriver, I pried out the earpiece. Then with a fine soldering iron, I unsoldered the two leads. Remember where the red lead should be attached (bottom for me).
Solder in the new earpiece and put everything back together again.
Drop me a line if you have questions, I'll gladly help to fix your Elephone earpiece if it's broken.

Headphones very faint in right ear

In the last week it appears my headphone port has become damaged.
I really love having a dedicated jack and using some quality headphones through a wired connection. Unfortunately the volume on the right channel has dropped to a very low, barely noticeable level. I have tried different headphones and have the same result with all. It does not appear that there is any lint or coating on the 3.5mm jacks and I cannot see anything down in the port.
Has anyone had a similar problem or able to provide advise?
I'd like to avoid a trip to AT&T or a warranty return if at all possible.
Thanks much, and thank you to all the posters for their great feedback and content.
Try vacuum or blowing out the port... I have seen similar posts of people having pocket lint in the port..
Sent from my [device_name] using XDA-Developers Legacy app
ScottieRotten said:
Try vacuum or blowing out the port... I have seen similar posts of people having pocket lint in the port..
Click to expand...
Click to collapse
Appreciate the response; suspect you are correct.
The problem seems to be gone, or disappearing. There must be something on the connectors in the port. I can now hear both channels but not quite balanced volume-wise, but seems to be improving over time.

I'm an idiot... What's the small hole at the top of the V30?

asd
The small top hole is one of the microphones. There's an identical one on the bottom of the phone. So, you can make stereo recordings.
https://goo.gl/images/VqxsYw
The earpiece actually turns into a 3rd microphone for high decibel environments, like live concerts.
But that top one is one of the two "regular" microphones.
Thanks, I thought so. Is it only for recording, or for noise reduction too? Recording I don't care about. Also, should I plug it with glue?
Mastiff said:
On autopilot I was going to put in a SIM card in my brand new phone and pressed where the hole was on my previous phone. Bad mistake, I guess... I probably put it right through something vital. Because I used the small hole at the top of the phone. Not the side. The light wasn't all that good, so I didn't notice that there was no SIM holder there. My guess is that it is a mike of some sorts, but I tried to record sound and had no problems with that. And it seems like there's a mike at the bottom of the thing too. So what did I mess up this time?
Edit: And does this mean that the phone isn't water resistant anymore? Can I stuff a bit of black silicone glue (the type used in bathroooms) in there with the pointy tool to make it water resistant again?
Edit 2: Oh, please drop the idiot jokes. I know it! Googling I have seen that I am far from the only one that has done that, I just would like to know exactly what it is on this phone, and if I should plug the hole to keep i waterproof. That's rather important for me, because I am an avid hobby crawfish and crab fisher and will probably get water splashing over this.
Click to expand...
Click to collapse
Aren't there barometer measuring apps for that ?
I read that by checking on pressure you can find out if your phone is still water resistant
Mastiff said:
Thanks, I thought so. Is it only for recording, or for noise reduction too? Recording I don't care about. Also, should I plug it with glue?
Click to expand...
Click to collapse
How about fixing it?
LG V30 Microphone Replacement
https://www.ifixit.com/Guide/LG+V30+Microphone+Replacement/104093
If you don't want to tackle it, cell phone repair shop can.
That top mic is probably used for noise reduction during phone calls (since it's the top mic and you would speak into the bottom one), but used for recording stereo when actually recording? I'm sort of guessing on this.
If someone who is audio has better answer, jump in.
zacharias.maladroit, I have also read that. But I have read that it doesn't work as well, since the holes "breathe", they are mes of goretex or similar material. But I'll try anyway, thanks.
ChazzMatt, Interesting, thanks! Looking at that video at around 4:55 it may seem like the pin must have penetrated to the side of the microphone! I think I see the pinhole to the right of where the actual microphone is. As for fixing it, I am far to clumsy. But using a shop is of course an option, the only thing is that the phone is brand new and I'm guessing I'll loose the warranty for that. But I think I will first of all find out if the microphone isn't damaged, and then I will see what happens when I cover the hole. If it doesn't change the call qualty I will probably choose (at least for now) to glue shut that pinhole. If it is a problem for call quality I can maybe live with that using a silicone case and a piece of electrical tape over the pinhole when I go out to fish.
ChazzMatt said:
How about fixing it?
LG V30 Microphone Replacement
https://www.ifixit.com/Guide/LG+V30+Microphone+Replacement/104093
If you don't want to tackle it, cell phone repair shop can.
That top mic is probably used for noise reduction during phone calls (since it's the top mic and you would speak into the bottom one), but used for recording stereo when actually recording? I'm sort of guessing on this.
If someone who is audio has better answer, jump in.
Click to expand...
Click to collapse
Mastiff said:
ChazzMatt, Interesting, thanks! Looking at that video at around 4:55 it may seem like the pin must have penetrated to the side of the microphone!
think I see the pinhole to the right of where the actual microphone is. As for fixing it, I am far to clumsy. But using a shop is of course an option, the only thing is that the phone is brand new and I'm guessing I'll loose the warranty for that. But I think I will first of all find out if the microphone isn't damaged, and then I will see what happens when I cover the hole. If it doesn't change the call qualty I will probably choose (at least for now) to glue shut that pinhole. If it is a problem for call quality I can maybe live with that using a silicone case and a piece of electrical tape over the pinhole when I go out to fish.
Click to expand...
Click to collapse
Yeah, 4:55 - 5:30 on that video shows taking out the old mic and putting in the new, for anyone else who needs to do it.
I thought it was the portal through which the Little Green men inVariably came out 30 times each night to hide your car keys, TV remote, and generally turn your life into a living hell?
Thread Owner request.
THREAD CLOSED

Categories

Resources