[Q] Phone freezes on HTC boot screen after restore - HTC EVO 3D

Hey guys
I've only just got into this stuff so please forgive my ignorance, but I need a hand understanding what might have gone wrong. I've got a GSM Evo 3D which I've unlocked through htcdev, phone is still S-ON, hboot 1.53.007. I flashed CWM recovery but have since switched to 4ext.
I downloaded Viper3D, ran a backup using 4ext recovery so I could go back to stock when I feel like it, then flashed the new ROM to test it out (mainly just testing the process). The phone booted fine - no problem. On that success, I went to restore the backup I made before flashing Viper3D. The restore completed successfully from 4ext recovery, but on trying to boot my phone it just hangs on the first HTC boot screen.
Tried rebooting a few times, tried restoring a second time, did wipe/factory reset first, tried clearing cache and dalvik cache, still just hangs on that HTC boot screen. I probably left it for about 20 minutes on that screen but it didn't go anywhere.
I flashed Viper3D again, and it worked again and my phone boots up fine. So the question is, what's going wrong when I try to restore my original backup? I haven't upgraded hboot or changed the kernel.
Would appreciate if someone could shed some light on this, cheers.

Ok so I think I've figured it out but could still do with a little clarification from someone.
I've read around and found that people have fixed the HTC screen hang by flashing the boot.img with fastboot from the PC, so I decided to give it a go. I copied the boot.img from my original backup to my PC, then booted the phone up into 4ext recovery and restored the backup. After restoring had completed, I rebooted into fastboot and hooked up to my PC, then flashed the boot.img from there. Once that was done, disconnected the phone from the PC and rebooted and the phone booted up fine into my stock ROM.
One thing I noticed when flashing Viper3D is that immediately after flashing, the phone would boot to the HTC screen, then reboot a second time by itself. I now understand this is where 4ext is flashing the boot.img with Smartflash, and it didn't reboot this second time when I was trying to restore my backup so I'm guessing that's where the problem lies.
So it looks to me like 4ext/Smartflash is not doing the whole process for some reason, perhaps a bug? Smartflash is enabled permanently on my phone, so I can't think of another reason why it didn't work except that it's bugged.
Can anyone confirm this issue or have any other comments? Cheers.

zaphodalive said:
So it looks to me like 4ext/Smartflash is not doing the whole process for some reason, perhaps a bug? Smartflash is enabled permanently on my phone, so I can't think of another reason why it didn't work except that it's bugged.
Can anyone confirm this issue or have any other comments? Cheers.
Click to expand...
Click to collapse
Read the requirements for the SmartFlash feature to work on the OP of the 4EXT Recovery thread, and in particular the limitations section. My guess is that you didn't have a bootable kernel when trying to use the SmartFlash option.
An easier way to re-flash the ROM in that situation is to start recovery with this fastboot command:
fastboot boot recovery.img (where recovery.img is the name of your 4EXT recovery file)
Click to expand...
Click to collapse
That command will boot any custom recovery in a mode that will let it flash the entire ROM from recovery, but for 4EXT you have to make sure that the SmartFlash/S-ON option is disabled in the tools menu and then flash the ROM zip file.
ramjet73

Ok thanks, just to clarify - by doing fastboot boot recovery.img, that would reboot the phone into 4ext recovery and allow it to flash both boot.img and recovery.img when flashing the ZIP? What exactly is the fastboot command doing that allows this?
Cheers

zaphodalive said:
Ok thanks, just to clarify - by doing fastboot boot recovery.img, that would reboot the phone into 4ext recovery and allow it to flash both boot.img and recovery.img when flashing the ZIP? What exactly is the fastboot command doing that allows this?
Cheers
Click to expand...
Click to collapse
The "fastboot boot" command starts the recovery as an OS image and just like Android it has the ability to flash the boot partition (kernel) when loaded that way. When started in the "recovery" mode it is not able to flash the boot partition when the phone is S-ON.
SmartFlash uses the same principle to flash the boot partition after the existing kernel is booted, but if the current kernel is not bootable SmartFlash doesn't work.
ramjet73

Ok, I kinda understand (without quite understanding)... can the same command be used for flashing ROMs in a ZIP? e.g. fastboot boot yourromhere.zip
Thanks

zaphodalive said:
Ok, I kinda understand (without quite understanding)... can the same command be used for flashing ROMs in a ZIP? e.g. fastboot boot yourromhere.zip
Thanks
Click to expand...
Click to collapse
No. The "fastboot boot" command only works with bootable images and not zip files.
ramjet73

Thanks very much for your help. A couple of final questions...
How can you flash a custom ROM in a ZIP with fastboot? e.g. the Viper3D ZIP didn't have a recovery.img, only a boot.img
Also, I'm downloading Cool ICS and CoolZ kernel, and this is my first time flashing a kernel. Checked the CoolZ ZIP file and there's no boot.img which I was expecting, so I'm hoping that 4ext won't have any problems flashing it..? Also not sure whether to flash CoolZ or Cool ICS first.
Cheers

The fastboot commands are part of the bootloader (hboot) and custom ROM's are flashed by recovery.
There are guides in the general forum that cover ROM flashing procedures including this one by mpgrimm2.
ramjet73

Thanks, getting stuck installing the CoolZ kernel. I rebooted into 4ext with fastboot boot recovery.img, disabled Smartflash, tried flashing the ZIP, and after extracting files I got the error message:
assert failed: write_raw_image(" /tmp/newboot.img", "boot")
I assume this means it failed writing to the boot partition... any thoughts why?

zaphodalive said:
assert failed: write_raw_image(" /tmp/newboot.img", "boot")
I assume this means it failed writing to the boot partition... any thoughts why?
Click to expand...
Click to collapse
If the assert fails that usually means you are trying to flash something that's not intended for your device. Make sure you are flashing the correct version since there are CoolZ kernels for both the CDMA and GSM Evo 3D models.
Edit: I just checked and it looks like the CoolZ v4.5 kernel has one installation file for both Evo 3D models.
Make sure you can boot into the ROM you flashed before you try to flash the kernel.
ramjet73

Ok, a little weird...
I tried installing the CoolZ kernel, that failed (as mentioned before), then I installed the v14 ROM and v14b update. Booted up the phone, had no WIFI (just said error). So I flashed the boot.img from the v14b ZIP after that to see if I'd get WIFI back, got a couple of bootloops on the splash screen, and it then booted up with WIFI working and the CoolZ kernel installed.
I originally downloaded the CoolZ kernel separately from the Cool ICS ROM, but it appears that the kernel is part of the ROM package so I didn't need to do that.
Anywho, seems to be working now so I'll have a fiddle around. Thanks very much for your help.

Related

I might have messed up

Guys,
I followed this guide to unlock my phone and gain superuser access step by step:
http://forum.xda-developers.com/showthread.php?t=1239821
I then installed Rom Manager, and restarted in Recovery.
I placed this zip: http://forum.xda-developers.com/showthread.php?t=1421065 onto my SD Card, and did not rename it. Once in recovery I installed that ROM. It installed with no errors however now the phone gets stuck at the htc logo screen.
Any thoughts?
What was contained that .zip file you flashed, and did you make a backup of your system before you flashed?
Sent from my Droid Razr Maxx
Did you wipe data cache and dalvik? If not wipe again. If it bootloops again try pushing the kernel with fastboot.
Sent from my PG86100 using Tapatalk
The .zip contains the following files:
data
devices
kernel
META-INF
sdcard
system
CHANGELOG
check_data_app
mike, can you tell me how to push the update with fastboot, I'm kind of new to all of this telephone wizardry
I can get into FASTBOOT/HBOOT/RECOVERY, however nothing I do seems to help me get past the HTC Logo. Any thoughts? Maybe I'm not waiting long enough? Can someone please tell me exactly what I need to do (if I can even do something). I might just be approaching this whole process the wrong way.
Do I install a ROM from ZIP from Recovery? Do I need to fastboot an .img file first?
Sounds like your hboot 1.5 and your phone is hanging due to you need to place a copy of your recovery in your adb folder...
The while in Hboot
Using adb with phone plugged in and debug turned on
fastboot boot recovery.img
Then wipe and flash the rom you were trying to flash...
You can't just flash a rom with recovery since your s-on
Two methods
One is fastboot boot recovery.img which is easy
Other is boot.img pain in the ass
I tried booting directly into recovery like you just said. I am using TWRP recovery.img file.
Can this be caused by the type of ROM that I am trying to install?
Everything works fine, the .zip gets applied and seems to install correctly, but it still hangs at the htc logo.
I also forgot to mention that originally I used Clockwork Recovery Mod, which i got from the market, and selected the option to boot into recovery. I don't know if that makes any difference.
You should Google shooter ruu. Get back to stock. Retry this with another shot at reading the instructions.
You must plug your phone into pc while in fastboot and give it a command to boot recovery recovery.img .
Then reflash a rom.
Read more I'm hboot 1.4 and I can still flash a 1.5 hboot correctly cause I've read how to.
Sent from my PG86100 using Tapatalk
If u haven't figured it out yet, see if this helps:
[Guide] My Hboot 1.50 HTC Unlock/recovery/rom/kernel flashing notes http://forum.xda-developers.com/show....php?t=1495358
If u have updated your phone to the newest radio in the 2.17.651.5 update you may have problems if the Rom is based on an earlier kernel/radio like I think Warm is, but I could be wrong.
You may have flashed the Rom incorrectly & not had the kernel get flashed causing the boot loop.
Sent from my "Up all night, sleep all day" Evo3D via Tapatalk.

HTC DUMLOCK - Flash boot from recovery without fastboot! (Updated 2012-02-28 v2)

HTC Dumlock
HTC Dumlock is a workaround for devices with HTC's unlock that cannot flash boot from recovery. Put simply, we make backups of recovery and boot, then we flash the backup of recovery to boot. When you reboot normally, you'll be in your recovery, but since your recovery is flashed to boot, you can make changes to boot. Head on over to our website for download links and instructions.
New v2 version scans / compares the backups of boot and recovery to help ensure that you don't run it twice and wipe out your backup of boot.
Hooray for Team Win! Here's my contribution:
http://rootzwiki.com/_/articles/rec...unlock-and-flashes-kernels-from-recovery-r432
Awesome work guys!
Sent from my Clean and MeanROM 3D
Can we flash custom roms with unlocked phone and hboot 1.5 with s-on directly from recovery now?
Edit: Nevermind the answer is yes. you guys are awesome.
this is awesome if i ever get hboot 1.5 again. Wish this was out a week ago i wouldn't of sold my phone so i could buy one with hboot 1.4
Kernels ok, but are we able to flash radios and such with this method?
I just htc unlocked, flashed the updated twrp via fastboot, then backed up, flashed su, installed HTC DumLock. When I try to use the app it finishes within a minute but does not reboot, rebooting to system reboots doesn't boot into TWRP. I gave the app root permissions, what else should I try?
Real cool news
This is awesome! Kudos! I'm a little squeamish to try it yet (I'm still android noobish ;-) ); I'll wait a bit until the more seasoned folk work the kinks out, but I'm extremely encouraged.
Edit: Changed notification
i tried twice to flash a kernel and i get is the progress bar sits there, i let it go for 10 minutes each time but it never flashed the zip
UPDATE: I got it i had to restore the backup
Everything went fine for me until i try to boot to system from recovery,it just reboots back to recovery
I even tried powering down and do a normal start and it go's into recovery
Can the recovery be made to recognize when it is booted using dumlock app and restore original boot automatically? Something like this,
Run dumlock app, writes recovery to boot but also sets a flag in your config file on the sdcard,
reboot to recovery in boot partition,
recovery sees flag in config file, then before allowing any interaction flashes your boot partition back to original and then allows you to flash away and reboot normal afterwards.
This to me would seem to make it a seemless process. I would think a modification could even be made to CM9 code that would execute the same type of commands to rewrite recovery to boot whenever you select "reboot to recovery" from the reboot menu by holding the power button to make this 100% seemless, no?
can I flash a radio with 1.50?
benny3 said:
UPDATE: I got it i had to restore the backup
Everything went fine for me until i try to boot to system from recovery,it just reboots back to recovery
I even tried powering down and do a normal start and it go's into recovery
Click to expand...
Click to collapse
re-read the instructions paying particular attention to steps 13-18.... then repeat step 18 like 9 times or so
gotojanoo said:
can I flash a radio with 1.50?
Click to expand...
Click to collapse
no...you are still s-off
alvintimothyjr said:
no...you are still s-off
Click to expand...
Click to collapse
actually am s-on with 1.50
Holy smokes, such an elegant solution. Doing this when I'm off work.
If u cant use fast boot to get to recovery how do u flash straigh to recovery?
Sent from my ADR6400L using Tapatalk
Anyone got this successfully working?
gotojanoo said:
actually am s-on with 1.50
Click to expand...
Click to collapse
Yeah that's what I meant...my bad
Interesting.
Is it basically copying the recovery image to the boot partition to get full access for flashing kernels/roms, then copying the recovery back afterwards?
I was wondering if someone would come up with something like this. Specifically, I had been wondering if there was a way to run fastboot from sdcard vs Pc to enter recovery.

[Q] Frozen at HTC screen and can't recover

Hi,
Let me start off by saying that I have viewed other threads but have not been able to find one that has this same exact problem. Can someone please help?
I have an HTC Evo 3D unlocked with the HTC method, S-On.
I put a new rom on my SD card, I was using InfectedRom but it had some issues. I loaded into bootloader and used revolutionary to flash the rom. I didn't do a wipe or anything else, thinking that it would just flash the rom and I would be good to go.
The phone gets stuck on the HTC splash screen when I go to boot it. I have tried everything from restoring from a back up, to wiping the phone to wiping the cache and am at a loss.
Can someone please offer me some advice? I really need to get this phone back up and running.
Thanks in advance.
Did you flash the boot.img for the ROM?
How can I do that?
Jep4444 said:
Did you flash the boot.img for the ROM?
Click to expand...
Click to collapse
Thanks for the quick response. How can I go about doing that?
thealist said:
Thanks for the quick response. How can I go about doing that?
Click to expand...
Click to collapse
Considering you're S-ON, how did you install a custom ROM in the first place without doing so?
thealist said:
Thanks for the quick response. How can I go about doing that?
Click to expand...
Click to collapse
You can do that by using fastboot to boot your recovery image.
Code:
fastboot boot [NAMEOFRECOVERY].img
Just running your recovery normally won't allow flashing to certain partitions.
From there, you shouldn't have any problems flashing the full image. The second option would be to use 4EXT recovery (There's a CDMA/GSM version, but don't know off the top of my head), or joeykrim's FlashImageGUI to assist in flashing to specific partitions from the phone.
Edit: CDMA and GSM correction.
Jep4444 said:
Considering you're S-ON, how did you install a custom ROM in the first place without doing so?
Click to expand...
Click to collapse
thealist took the HTCDev unlock which doesn't give S-OFF, but does allow the user to flash custom ROMs.
~co~
closeone said:
You can do that by using fastboot to boot your recovery image.
Code:
fastboot boot [NAMEOFRECOVERY].img
Just running your recovery normally won't allow flashing to certain partitions.
From there, you shouldn't have any problems flashing the full image. The second option would be to use 4EXT recovery (There's a CDMA/GSM version, but don't know off the top of my head), or joeykrim's FlashImageGUI to assist in flashing to specific partitions from the phone.
Edit: CDMA and GSM correction.
thealist took the HTCDev unlock which doesn't give S-OFF, but does allow the user to flash custom ROMs.
~co~
Click to expand...
Click to collapse
Don't S-ON roms still need the boot.img to be flashed to install any ROM?
closeone said:
You can do that by using fastboot to boot your recovery image.
Code:
fastboot boot [NAMEOFRECOVERY].img
Where do I find my recovery image?
Just running your recovery normally won't allow flashing to certain partitions.
From there, you shouldn't have any problems flashing the full image. The second option would be to use 4EXT recovery (There's a CDMA/GSM version, but don't know off the top of my head), or joeykrim's FlashImageGUI to assist in flashing to specific partitions from the phone.
Edit: CDMA and GSM correction.
Thanks. Where would I find this and do I put that into the root sd card portion of my phone and then run through the bootloader? Sorry, I am relatively new to this process. Thanks for your patience.
thealist took the HTCDev unlock which doesn't give S-OFF, but does allow the user to flash custom ROMs.
That's exactly what I did.
~co~
Click to expand...
Click to collapse
Thanks for all the help. It's very much appreciated.
closeone said:
You can do that by using fastboot to boot your recovery image.
Code:
fastboot boot [NAMEOFRECOVERY].img
Just running your recovery normally won't allow flashing to certain partitions.
From there, you shouldn't have any problems flashing the full image. The second option would be to use 4EXT recovery (There's a CDMA/GSM version, but don't know off the top of my head), or joeykrim's FlashImageGUI to assist in flashing to specific partitions from the phone.
Edit: CDMA and GSM correction.
thealist took the HTCDev unlock which doesn't give S-OFF, but does allow the user to flash custom ROMs.
~co~
Click to expand...
Click to collapse
Sorry, my last post did not quote correctly.
How do I find my recovery image?
Once I get FlashImageGUI, do I put that into the root of my SD card by plugging it into my mac?
Jep4444 said:
Don't S-ON roms still need the boot.img to be flashed to install any ROM?
Click to expand...
Click to collapse
Well, all ROMs will need to have a boot.img flashed to boot, but since they are included in the ZIP file containing the ROM, they are normally flashed along with the ROM. If you use FlashImageGUI, you can flash from a boot.img or from a kernel zip file. By running the fastboot boot command, this allows the user to flash to partitions that are locked when booted into recovery from the bootloader.
thealist said:
Sorry, my last post did not quote correctly.
How do I find my recovery image?
Once I get FlashImageGUI, do I put that into the root of my SD card by plugging it into my mac?
Click to expand...
Click to collapse
These are two different methods for accomplishing the same task.
Have you loaded a custom recovery (like ClockworkMod Recovery, TWRP, or 4EXT) before? If you've kept the recovery image on your computer, you can just use that one. Instead of flashing it to your recovery partition (fastboot flash recovery [NAMEOFRECOVERY].img), you would boot to it instead (fastboot boot [NAMEOFRECOVERY].img).
If you use want to use FlashImageGUI, you would copy it to your SD card, install it on the phone, and run the app. Make sure that you've got the ROM you want to flash on the SDCard. If I remember correctly, FlashImageGUI will pull the boot.img out of the ZIP and flash it. Then you will have to boot into your custom recovery to flash the rest of the image. Flashing just the boot image will most likely leave you with a phone that won't boot (until you flash the rest of the ROM).
~co~
closeone said:
Well, all ROMs will need to have a boot.img flashed to boot, but since they are included in the ZIP file containing the ROM, they are normally flashed along with the ROM. If you use FlashImageGUI, you can flash from a boot.img or from a kernel zip file. By running the fastboot boot command, this allows the user to flash to partitions that are locked when booted into recovery from the bootloader.
These are two different methods for accomplishing the same task.
Have you loaded a custom recovery (like ClockworkMod Recovery, TWRP, or 4EXT) before? If you've kept the recovery image on your computer, you can just use that one. Instead of flashing it to your recovery partition (fastboot flash recovery [NAMEOFRECOVERY].img), you would boot to it instead (fastboot boot [NAMEOFRECOVERY].img).
If you use want to use FlashImageGUI, you would copy it to your SD card, install it on the phone, and run the app. Make sure that you've got the ROM you want to flash on the SDCard. If I remember correctly, FlashImageGUI will pull the boot.img out of the ZIP and flash it. Then you will have to boot into your custom recovery to flash the rest of the image. Flashing just the boot image will most likely leave you with a phone that won't boot (until you flash the rest of the ROM).
~co~
Click to expand...
Click to collapse
I have never loaded ClockworkMod Recovery, TWRP, or 4EXT to my phone. Is that something I can download online and then transfer to my phone using the bootloader? I have Revolutionary which allows me to mount the SD card. Same thing goes for FlasImageGUI. I can't get past the HTC load screen so is that something I can just transfer and use Bootloader with?
thealist said:
I have never loaded ClockworkMod Recovery, TWRP, or 4EXT to my phone. Is that something I can download online and then transfer to my phone using the bootloader? I have Revolutionary which allows me to mount the SD card. Same thing goes for FlasImageGUI. I can't get past the HTC load screen so is that something I can just transfer and use Bootloader with?
Click to expand...
Click to collapse
What is this 'Revolutionary' that you're talking about? I realize that multiple pieces of software can be called the same thing though. How did you load on the ROM that you're currently on? Also, before I link you anywhere (because I don't want you loading the wrong recovery on your phone), is your phone on Sprint, or another carrier? You'd use Recovery to load ROMs, back them up, and so on.
What exactly was it that you were trying to do? Or rather, how did the phone get to a state where it's frozen on the HTC logo? Do you have a custom ROM loaded, or the stock ROM?
Sorry for all the questions, and hopefully this response doesn't come off rude (I don't mean it to ). I'm just trying to figure out what's going on before I suggest anything.
If you are on Sprint, you can run this recovery from Fastboot USB mode.
Code:
fastboot boot cwm-4.0.1.4-shooter.img
~co~
closeone said:
What is this 'Revolutionary' that you're talking about? I realize that multiple pieces of software can be called the same thing though. How did you load on the ROM that you're currently on? Also, before I link you anywhere (because I don't want you loading the wrong recovery on your phone), is your phone on Sprint, or another carrier? You'd use Recovery to load ROMs, back them up, and so on.
What exactly was it that you were trying to do? Or rather, how did the phone get to a state where it's frozen on the HTC logo? Do you have a custom ROM loaded, or the stock ROM?
Sorry for all the questions, and hopefully this response doesn't come off rude (I don't mean it to ). I'm just trying to figure out what's going on before I suggest anything.
If you are on Sprint, you can run this recovery from Fastboot USB mode.
Code:
fastboot boot cwm-4.0.1.4-shooter.img
~co~
Click to expand...
Click to collapse
Your questions are really appreciated. Sorry I haven't been more clear.I really appreciate the help as I've gotten myself in trouble here.
I went on htcevohack and found how to flash the synergy infectedrom. The rom has some bugs in it so I downloaded a new rom and placed in the root folder of my SD card. Revolutionary is a program that allows me to wipe data, install from zip card, mount storage so and so forth. I tried to flash the zip from the new rom using this program and this is where I have had the problem. I have the Sprint Evo 3D. I am relatively new to this and just want a stable rom that has wifi tether on it. Thanks again for the help and for the patience.
thealist said:
Your questions are really appreciated. Sorry I haven't been more clear.I really appreciate the help as I've gotten myself in trouble here.
I went on htcevohack and found how to flash the synergy infectedrom. The rom has some bugs in it so I downloaded a new rom and placed in the root folder of my SD card. Revolutionary is a program that allows me to wipe data, install from zip card, mount storage so and so forth. I tried to flash the zip from the new rom using this program and this is where I have had the problem. I have the Sprint Evo 3D. I am relatively new to this and just want a stable rom that has wifi tether on it. Thanks again for the help and for the patience.
Click to expand...
Click to collapse
Oh! Now I know what your talking about. Max from HTCEVOHacks put the Revolutionary branded version of ClockworkMod Recovery in that archive. I know that for a fact (I downloaded it). It's actually the same version of ClockworkMod Recovery that I linked you to.
Okay. Here's my suggestion to start out with. Flash the recovery.img he included (CWM) onto your phone by booting it up into the bootloader, connecting it to your computer making sure that the phone is in FASTBOOT USB mode. Instead of running the command:
Code:
fastboot boot recovery.img
Run the command:
Code:
fastboot flash recovery recovery.img
That will put a copy of ClockworkMod Recovery on your phone. It's accessible by selecting Recovery from the HBOOT menu.
Now, because HTC's Unlock method doesn't unlock enough to flash most images to your phone, you'll still have to run the 'fastboot boot recovery.img' command each time you want to flash different image. That's the classic way we have used to get around HTC's restrictions.
From there, you can flash another image. Make sure to wipe data before flashing.
The reason I told you to also flash the recovery image to your phone is because, you can still create NANDroid backups without connecting to a computer. However, to restore those backups, you'll have to 'fastboot boot ...' the recovery image.
Now, his archive is quite dated. I'd personally recommend after you flash a new ROM, that you take a look at the 4EXT recovery thread in the EVO 3D CDMA development forum. It's really very good (I also like TWRP as well).
Now, there probably wasn't a problem with the ROM. I've used it myself, and have found it to be quite stable. If you flash a ROM onto the phone without wiping data first, you'll probably run into problems booting the ROM. If you liked InfectedRom Eternity, you can always try it again.
This is where NANDroid backups are important. If anything gets messed up, you can easily restore from one in your custom recovery (CWM/4EXT/TWRP).
I hope I didn't throw too much out there. Hopefully this gets you off the ground.
~co~
closeone said:
Oh! Now I know what your talking about. Max from HTCEVOHacks put the Revolutionary branded version of ClockworkMod Recovery in that archive. I know that for a fact (I downloaded it). It's actually the same version of ClockworkMod Recovery that I linked you to.
Okay. Here's my suggestion to start out with. Flash the recovery.img he included (CWM) onto your phone by booting it up into the bootloader, connecting it to your computer making sure that the phone is in FASTBOOT USB mode. Instead of running the command:
Code:
fastboot boot recovery.img
Run the command:
Code:
fastboot flash recovery recovery.img
That will put a copy of ClockworkMod Recovery on your phone. It's accessible by selecting Recovery from the HBOOT menu.
Now, because HTC's Unlock method doesn't unlock enough to flash most images to your phone, you'll still have to run the 'fastboot boot recovery.img' command each time you want to flash different image. That's the classic way we have used to get around HTC's restrictions.
From there, you can flash another image. Make sure to wipe data before flashing.
The reason I told you to also flash the recovery image to your phone is because, you can still create NANDroid backups without connecting to a computer. However, to restore those backups, you'll have to 'fastboot boot ...' the recovery image.
Now, his archive is quite dated. I'd personally recommend after you flash a new ROM, that you take a look at the 4EXT recovery thread in the EVO 3D CDMA development forum. It's really very good (I also like TWRP as well).
Now, there probably wasn't a problem with the ROM. I've used it myself, and have found it to be quite stable. If you flash a ROM onto the phone without wiping data first, you'll probably run into problems booting the ROM. If you liked InfectedRom Eternity, you can always try it again.
This is where NANDroid backups are important. If anything gets messed up, you can easily restore from one in your custom recovery (CWM/4EXT/TWRP).
I hope I didn't throw too much out there. Hopefully this gets you off the ground.
~co~
Click to expand...
Click to collapse
Thanks a lot! I am going to try this right now. I have a mac so I am assuming that I need to use terminal which is what I originally used. Do you know if the extension you provided were also for a mac?

HTC evo 4g LTE can't load system again

Hi people facing a problem with my Phone. The problem is it won't reboot to system anymore even when i select system after going into reboot menu in Team Win Recovery Project v2.2.1 ...What happens is when i select system in the reboot menu, it boots to my Teamwin recovery instead of system but when i select power off or recovery or bootloader it goes into those fine. I even tried factory reset from bootloader and from Teamwin recovery but it still reboots to Teamwin recovery. I just want it to be able to get to my system again so i can have everything working..
This is what i did before it became like this. I was on HTCevohacks on the HTC evo 4g lte roms page trying to install CM10 ROM for Rooted HTC Evo 4G LTE! [Android 4.1.2][STABLE]. i downloaded CM10 Rom zip file and Gapps 4.1.2 zip file. i put both on my external storage then tried to install them and fail but before that i made a backup of my System, Data and Boot on my external storage. When it failed i factory reset from recovery without restoring backups and it started up perfectly, i even set up my phone interface again linking my google mail and wifi connections. next i went back to recovery and restore my backups from my external storage and that's when i couldn't get back to system. I still have my backup files. They are boot.emmc.win, boot.emmc.win.md5, data.ext4.win.md5, system.ext4.win and system.ext4.win.md5...
this is my HTC evo 4g lte specs..
Flashed to boostmobile
unlocked
Jewel put ship s-on RL
Hboot-1.15.0000
Radio-1.05.11.0606
OpenDSP-v25.1.0.32.0405
eMMc-boot
PLEASE HELP ANYWAY HOW!!just want to go back into system again
You'll need to flash the boot.img through fastboot if you have s-on
xHausx said:
You'll need to flash the boot.img through fastboot if you have s-on
Click to expand...
Click to collapse
I don't have a boot.img to flash that i know off so where do i get my boot.img so i can flash it and have my system running again?
Pull the boot img from the rom your flashing. You should probably read the "don't panic " thread stickied in q&a. All your answers are there
Sent from my EVO using xda premium
If booting system is loading twrp then you have flashed twrp as a kernel, flash a Rom with kernel installer or fastboot kernel
om4 said:
If booting system is loading twrp then you have flashed twrp as a kernel, flash a Rom with kernel installer or fastboot kernel
Click to expand...
Click to collapse
Yes, that makes a lot more sense, i think i flashed twrp as a kernel without knowing it that's why booting system boots to twrp..bout bro i'm still new to this whole thing so please explain step by step how i can flash a Rom with kernel installer or fastboot kernel or provide a link to a guide..please my phone is off nd i'm missing out on calls, i really need to put it back to normal nd not miss with it anymore..i appreciate your first help..
You need to find a ROM that is son friendly, like meanrom. It will flash the whole ROM including the boot.IMG just like you would if you were s-off. It doesnt need anything extra done on your part. Or you need to extract the boot.img from your cm zip and fastboot flash that. In order to fastboot flash the kernel you need to set up adb. Google how to set up adb on windows or Mac or Linux or whatever os your computer is.
thedecider said:
Yes, that makes a lot more sense, i think i flashed twrp as a kernel without knowing it that's why booting system boots to twrp..bout bro i'm still new to this whole thing so please explain step by step how i can flash a Rom with kernel installer or fastboot kernel or provide a link to a guide..please my phone is off nd i'm missing out on calls, i really need to put it back to normal nd not miss with it anymore..i appreciate your first help..
Click to expand...
Click to collapse
Meanrom has a kernel installer, just leave it alone for 5-10 minutes to install. Or to flash kernel manually, when you are ready to flash a Rom extract the boot.img from the Rom zip and use uniflash, bootimg flasher, or fastboot to flash it. ADB Tools and HTC drivers are all you need to flash the kernel through fastboot. Just extract folder and place boot image inside. In windows you can hold shift and right click, select open command window here for the terminal. Then connect phone I'm fastboot (bootloader/fastboot) and type fastboot devices to make sure the pc sees it. Type fastboot flash boot boot.img and then boot recovery and flash rom

HELP! Soft Bricked HTC One S!

I'm not new to flashing custom roms and rooting Android devices, so I don't think I'm a noob at this. I decided to help my friend unleash the power in his HTC One S by rooting it and giving it a custom recovery, I went through the right processes, Unlocked the phone's bootloader, and flashed the superuser zip and the twrp image, as it didn't seem like a clockworkmod image was compatible with the phone.
I then booted into recovery, wiped/factory reset and then flashed the latest CM11 nightly and got an error in TWRP recovery about the bootloader not been interoperable something like "
Code:
2.15==2.13"
in the error message , fine, I rebooted back into fastboot and checked the HBOOT Version and found out the phone was on HBOOT 1.13 and I think CM11 requires the most recent HBOOT version to work on HTC devices. The phone has got S-Off though.
Now I'm stuck in a bootloop cause I already wiped the OS in TWRP, I have everything in place, the right drivers and all that, I also tried re-installing the stock rom by downloading an HTC One S's RUU file but the device wasn't recognized at all by the RUU installer, I also tried to flash a stock 4.0.x rom as a zip file, no Joy. Now the phone is stuck at the point where it doesn't have an OS to boot into at all.
I'll really appreciate the community's support helping me fix this issue.
geek-x said:
I'm not new to flashing custom roms and rooting Android devices, so I don't think I'm a noob at this. I decided to help my friend unleash the power in his HTC One S by rooting it and giving it a custom recovery, I went through the right processes, Unlocked the phone's bootloader, and flashed the superuser zip and the twrp image, as it didn't seem like a clockworkmod image was compatible with the phone.
I then booted into recovery, wiped/factory reset and then flashed the latest CM11 nightly and got an error in TWRP recovery about the bootloader not been interoperable something like "
Code:
2.15==2.13"
in the error message , fine, I rebooted back into fastboot and checked the HBOOT Version and found out the phone was on HBOOT 1.13 and I think CM11 requires the most recent HBOOT version to work on HTC devices. The phone has got S-Off though.
Now I'm stuck in a bootloop cause I already wiped the OS in TWRP, I have everything in place, the right drivers and all that, I also tried re-installing the stock rom by downloading an HTC One S's RUU file but the device wasn't recognized at all by the RUU installer, I also tried to flash a stock 4.0.x rom as a zip file, no Joy. Now the phone is stuck at the point where it doesn't have an OS to boot into at all.
I'll really appreciate the community's support helping me fix this issue.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2322755
You need that. Luckily you're already S-Off, so shouldn't be terrible to get going again. Just update the firmware, reinstall TWRP and re-flash CM11. Should be good to go afterwards.
es0tericcha0s said:
http://forum.xda-developers.com/showthread.php?t=2322755
You need that. Luckily you're already S-Off, so shouldn't be terrible to get going again. Just update the firmware, reinstall TWRP and re-flash CM11. Should be good to go afterwards.
Click to expand...
Click to collapse
Thank you so much for the reply, does it matter that I don't have an OS to boot into as I already wiped and factory reset the phone for installation of a new rom.?
geek-x said:
Thank you so much for the reply, does it matter that I don't have an OS to boot into as I already wiped and factory reset the phone for installation of a new rom.?
Click to expand...
Click to collapse
Nah, shouldn't. The firmware we're referring to here is independent of the OS.
es0tericcha0s said:
Nah, shouldn't. The firmware we're referring to here is independent of the OS.
Click to expand...
Click to collapse
At the end of the guide, should help fix the issue, there's a part where I'm supposed to install the new CM kernel from the CM .zip package, how do I flash a kernel from Fastboot?
geek-x said:
At the end of the guide, should help fix the issue, there's a part where I'm supposed to install the new CM kernel from the CM .zip package, how do I flash a kernel from Fastboot?
Click to expand...
Click to collapse
Since you are S-Off, needing fastboot to install the boot.img is not necessary. It will install through recovery.
But, for future reference, you would boot to the bootloader screen, select fastboot, then assuming you have fastboot set up on the PC and the boot.img in the directory of said fastboot, you would use this command:
fastboot flash boot boot.img
then
fastboot reboot
es0tericcha0s said:
Since you are S-Off, needing fastboot to install the boot.img is not necessary. It will install through recovery.
But, for future reference, you would boot to the bootloader screen, select fastboot, then assuming you have fastboot set up on the PC and the boot.img in the directory of said fastboot, you would use this command:
fastboot flash boot boot.img
then
fastboot reboot
Click to expand...
Click to collapse
I tried flashing the firmware.zip file from the thread but I got a FAILED: (remote: not allowed) error in command prompt at the end of the process, what did I do wrong?
UPDATE: I was able to update the bootloader version successfully, as I forgot the part where I was to boot into RUU mode with fastboot oem rebootRUU and worked perfectly the second time.
I rebooted and found out the boot loader was updated to HBoot 2.15, and I also updated twrp to the latest S4 version but now in recovery I get errors about twrp been unable to mount the /data partition. Do I flash another recovery image?
UPDATE:
Thank you so much es0tericcha0s, I really appreciate the support, I got the /data mount issue fixed finally. I just had to flash an older twrp recovery image and then reflashed the new one in fastboot and I could then flash CM successfully.
I can't believe I finally unbricked this phone, its been bricked since Sunday. Once again, es0tericcha0s, Thank you!
geek-x said:
UPDATE: I was able to update the bootloader version successfully, as I forgot the part where I was to boot into RUU mode with fastboot oem rebootRUU and worked perfectly the second time.
I rebooted and found out the boot loader was updated to HBoot 2.15, and I also updated twrp to the latest S4 version but now in recovery I get errors about twrp been unable to mount the /data partition. Do I flash another recovery image?
Click to expand...
Click to collapse
You might need to RUU back then. If you have issues with the RUU exe, then you can extract the rom.zip and install it like you did the firmware. There are quite a few tutorials on how to extract it, or there might already be a version floating around for your phone.

Categories

Resources