[Q] Mount internal or ext SD card from Recovery - Galaxy S III Q&A, Help & Troubleshooting

Hi guys,
I basically wiped my phone and completely forgot to copy the ROM I wanted to flash into my ext SD card. Now, the phone has no ROM to boot into and I need to be able to mount it onto Windows from within the recovery to be able to do it. I'm running CWM 6.0.2.7
Has anyone ever done this? What should I do?
Thanks

Wipe data doesn't mean format (like PC) it's just a factory reset
you can flash any official FW for your device by Odin

So it isn't possible for Windows to detect the phone in any way so I can copy the ROM into it?

It's possible by using ADB and push it
but why you don't boot up your device and copy it?

Use adb to push the file onto the card. Or remove ext. SD card and use a reader to copy it over.

Here is a good adb interface, it has easy push/pull where you just supply the two file paths and hit go,
http://forum.xda-developers.com/showthread.php?t=2097848
[TOOL] ADB Command Center [Alpha]

Thanks for the prompt replies everyone.
I just re-flashed an original FW through Odin, rooted it back, re-installed CWM Recovery and now tried to flash a new rom, in this case, Foxhound and after it tries to reboot it comes back into CWM always... it never boots into the ROM..
Anyone has any clue why this would be happening?

Sptz said:
Thanks for the prompt replies everyone.
I just re-flashed an original FW through Odin, rooted it back, re-installed CWM Recovery and now tried to flash a new rom, in this case, Foxhound and after it tries to reboot it comes back into CWM always... it never boots into the ROM..
Anyone has any clue why this would be happening?
Click to expand...
Click to collapse
Try reinstall it
Sent from my GT-I9300 using xda premium

qtwrk said:
Try reinstall it
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
The ROM? Just did and the same thing happens, boots up to Samsun Galaxy logo, then that "eye" logo then reboots again into CWM. At all times.
I just installed Omega just to try it out and it works, boots into the ROM, with Foxhound it doesn't even reach the Foxhound Logo, it reboots and goes back to CWM... Any ideas? I can't post in the Foxhound thread due to lack of posts

Flash stock Rom, and allow it to boot up properly before you do anything else....did you do that?

slaphead20 said:
Flash stock Rom, and allow it to boot up properly before you do anything else....did you do that?
Click to expand...
Click to collapse
Yes, two times already. Then rooted, then flashed CWM Recovery then wiped data etc, flashed foxhound and same thing happens. Tried Omega and it boots into it, it's only Foxhound and I really wanted to try it...
I'm sorry this thread has derailed into another issue but thought it wasn't worth cluttering with yet another thread.

Is it possible to shut down the phone from CWM Recovery aside from doing a battery pull?

Could be a bad download. Try downloading again.

Related

[Q] Have I softbricked

Ok, I made a schoolboy error and think I have softbricked my phone.
I just got it this morning and have rooted it through ODIN. I was going to install a ROM but when in recovery I went and used the Superwipe app and then rebooted (don't ask) and it is now stuck on the Samsung logo screen. I can boot into recovery but of course no backup as its been wiped.
I am downloading a Stock Official and going to install through ODIN. I assume this is the right way to getting back to stock and starting again to unsoftbrick my SIII?
Its the first time I have ever arsed up. Its not nice lol
Haizum74 said:
Ok, I made a schoolboy error and think I have softbricked my phone.
I just got it this morning and have rooted it through ODIN. I was going to install a ROM but when in recovery I went and used the Superwipe app and then rebooted (don't ask) and it is now stuck on the Samsung logo screen. I can boot into recovery but of course no backup as its been wiped.
I am downloading a Stock Official and going to install through ODIN. I assume this is the right way to getting back to stock and starting again to unsoftbrick my SIII?
Its the first time I have ever arsed up. Its not nice lol
Click to expand...
Click to collapse
Yup, as long as you can get to download mode, you can use odin and flash back to stock.
Haizum74 said:
Ok, I made a schoolboy error and think I have softbricked my phone.
I just got it this morning and have rooted it through ODIN. I was going to install a ROM but when in recovery I went and used the Superwipe app and then rebooted (don't ask) and it is now stuck on the Samsung logo screen. I can boot into recovery but of course no backup as its been wiped.
I am downloading a Stock Official and going to install through ODIN. I assume this is the right way to getting back to stock and starting again to unsoftbrick my SIII?
Its the first time I have ever arsed up. Its not nice lol
Click to expand...
Click to collapse
Yup enter in to download mode and flash it using ODIN everythin wil b fine I hav experienced the same problem so many times
Phew, I was panicking there. Thanks guys. Do I also need to download the seperate kernel and modem? Im coming from a Nexus S and didnt have these options
Haizum74 said:
Ok, I made a schoolboy error and think I have softbricked my phone.
I just got it this morning and have rooted it through ODIN. I was going to install a ROM but when in recovery I went and used the Superwipe app and then rebooted (don't ask) and it is now stuck on the Samsung logo screen. I can boot into recovery but of course no backup as its been wiped.
I am downloading a Stock Official and going to install through ODIN. I assume this is the right way to getting back to stock and starting again to unsoftbrick my SIII?
Its the first time I have ever arsed up. Its not nice lol
Click to expand...
Click to collapse
I have the exact problem as you,but I couldn't flash the stock rom for my country..via Odin
Don't bother with superwipe, just wipe data/factory reset in cwm and of you really feel the need you can format system under mounts and storage in cwm.
Just make sure you have something to flash already on your phone before you do, and don't reboot after formatting system.
Flashing stock via Odin will fix your problem now.
Sent from my GT-I9300 using xda premium
nodstuff said:
Don't bother with superwipe, just wipe data/factory reset in cwm and of you really feel the need you can format system under mounts and storage in cwm.
Just make sure you have something to flash already on your phone before you do, and don't reboot after formatting system.
Flashing stock via Odin will fix your problem now.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Thanks. I dont usually format and have no idea why I thought it was a good idea to do it this time. I was going to mount internal storage through CWM and put the ROM on it but there was no option to mount it.
EDIT - All sorted. Thanks for the info
If you know how to use adb you could put the ROM on your sdcard through cwm.
Sent from my GT-I9300 using xda premium
Or if you're not comfortable with adb and got an external SD, put the external SD in your PC and transfer the cwm rom to that and flash it from external SD on your phone
if i helped-hit thanx

PLEASE REPLY Stuck in recovery!!!!

OK so Im on AOKP milestone 6 with the devil kernel and i went in to recovery to wipe cache and dalvik cache and when i pressed reboot system it goes back to recovery!!!! please help as I really don't want to reflash everything!!! Thanks.
I had this same problem until I flashed TWRP. When I rebooted, it instead loaded the OS, but it still had Devil Recovery. WTF?
Have you tried re-flashing the rom without wiping data?
Sent from my SCH-I500 using xda premium
I can't flash anything because i can't put anything on the sd card because i cant get out of recovery!
ThePlasticBling said:
I can't flash anything because i can't put anything on the sd card because i cant get out of recovery!
Click to expand...
Click to collapse
i have the same problem i cant get out of recovery, cause the rom i flashed is all screwed up
android_noob01 said:
i have the same problem i cant get out of recovery, cause the rom i flashed is all screwed up
Click to expand...
Click to collapse
Try flashing CWM recovery again using Heimdall or Odin. Once it boots into recovery, flash TWRP or another recovery of your choice, then reboot and hopefully you will see your boot animation. That's what I did to get AOKP build 40 to boot again (though strangely enough, it's stuck with Devil recovery even after flashing TWRP). Hope this helps you guys out. And be sure to make backups!
UndeadSquirrel said:
Try flashing CWM recovery again using Heimdall or Odin. Once it boots into recovery, flash TWRP or another recovery of your choice, then reboot and hopefully you will see your boot animation. That's what I did to get AOKP build 40 to boot again (though strangely enough, it's stuck with Devil recovery even after flashing TWRP). Hope this helps you guys out. And be sure to make backups!
Click to expand...
Click to collapse
Again, how can i put twrp on my sd card if i'm stuck in recovery? Is there a link for an odin version of twrp
You should be able to mount your SD card in recovery anyway. If not, take it out and insert it into an adapter to plug into your computer. I don't know if there's an Odin version of TWRP, I flashed it in CWM recovery.
I would read droid styles guide first if you have not yet as it has all the answers you will need. You just need to read through it and following the directions.
Sent from my SCH-R530U
how do i mount my sd card and open it on my pc in recovery?
If you're using CWM, it's under Advanced or Mounts and Storage. Plug in the USB cable like you normally would.
UndeadSquirrel said:
If you're using CWM, it's under Advanced or Mounts and Storage. Plug in the USB cable like you normally would.
Click to expand...
Click to collapse
I try to install twrp but it says installation aborted. I'm really starting to get sick of this phone and its stability issues.
You got the zip, right? It's in the Fascinate development section of the forums.
There is nothing wrong with the phone. I don't understand why you can't just Odin back to stock and start over. With the amount of time you have been stuck in recovery you could have fixed it by now. It you could follow droid styles guide to get out of the recovery loop without going back to stock. Something tells me you really just want a new phone...am I close???
Sent from my SCH-R530U
shelby04861 said:
There is nothing wrong with the phone. I don't understand why you can't just Odin back to stock and start over. With the amount of time you have been stuck in recovery you could have fixed it by now. It you could follow droid styles guide to get out of the recovery loop without going back to stock. Something tells me you really just want a new phone...am I close???
Sent from my SCH-R530U
Click to expand...
Click to collapse
Sent from my SCH-R530U
Don't you belong in a different section?
Anyway, sorry for getting snippy, I was just really tired and frustrated. I did use the .zip from the forums.
If you've already tried Heimdall-flashing CWM again, and that didn't work, then I suggest you Odin back to stock as shelby suggested. If you haven't made a nandroid already, do so, then revert back to stock and start from scratch. You can try restoring your nandroid once you're no longer stuck in recovery.
ThePlasticBling said:
Sent from my SCH-R530U
Don't you belong in a different section?
Anyway, sorry for getting snippy, I was just really tired and frustrated. I did use the .zip from the forums.
Click to expand...
Click to collapse
I have a mez and I just got the sgs3 a little while ago. You need to check out section 8 or 9 I think of the guide. It tells you exactly how to get out of your situation.
Sent from my SCH-I500 using Tapatalk 2
There's also a topic about the "three-finger recovery boot loop" fix. You could try that.

[Q] SGS2 Bricked on ROM 1 after downgrading from JB 4.1.1

Hi,
This is my first post so i apologise if its in the wrong place. I have been running ICS 4.0.3 for quite some time and decided it was time to try a different ROM. I installed AOKP 4.1.1, gapps_jb_signed with Siyah kernel S2.4.1.5 ( i think). After a few days it kept hanging etc and switching off as i would expect a build in development to do. Anyway i flashed a new kernal to change the look (dark demonoid or something like that) and then rebooted. My phone was now properly bricked like i'd never seen before and would'nt even go into recovery mode. After a day or two of trying everything I could to get it to at least boot i flashed Siyah kernel knowing that it had a dual boot option. Low and behold it worked but only in the 2nd ROM mode where i was able to restore my old ICS 4.0.3 from Nandroid backup. The problem I have now is that when i try to do a factory restore/data wipe from within CWM it gets stuck at the data wipe point and eventually shuts down.
I have tried mounting and unmounting emmc,eft,system, data etc and wiping clean everything but to no avail.
When i try to restore the nandroid backup onto the 1st ROM partition it hangs when installing data and I have also tried reformating the data from within the dual boot options of siyah kernel. Nothing seems to work. Have i fried the chip or something? or am i just missing a procedure. My phone works but only if i keep it on siyah kernel and boot into the 2nd ROM option where i have ICS installed..
Any help would be appreciated.
Hi,<br />
This is my first post so i apologise if its in the wrong place. I have been running ICS 4.0.3 for quite some time and decided it was time to try a different ROM. I installed AOKP 4.1.1, gapps_jb_signed with Siyah kernel S2.4.1.5 ( i think). After a few days it kept hanging etc and switching off as i would expect a build in development to do. Anyway i flashed a new kernal to change the look (dark demonoid or something like that) and then rebooted. My phone was now properly bricked like i'd never seen before and would'nt even go into recovery mode. After a day or two of trying everything I could to get it to at least boot i flashed Siyah kernel knowing that it had a dual boot option. Low and behold it worked but only in the 2nd ROM mode where i was able to restore my old ICS 4.0.3 from Nandroid backup. The problem I have now is that when i try to do a factory restore/data wipe from within CWM it gets stuck at the data wipe point and eventually shuts down.<br />
<br />
I have tried mounting and unmounting emmc,eft,system, data etc and wiping clean everything but to no avail.<br />
<br />
When i try to restore the nandroid backup onto the 1st ROM partition it hangs when installing data and I have also tried reformating the data from within the dual boot options of siyah kernel. Nothing seems to work. Have i fried the chip or something? or am i just missing a procedure. My phone works but only if i keep it on siyah kernel and boot into the 2nd ROM option where i have ICS installed..<br />
<br />
Any help would be appreciated.
Click to expand...
Click to collapse
hi mate.can you please mention which roms you were using in dual boot?well yo be honest dual boot ain't a good idea.if you would ha e asked me.i would have recommented you not to do dual boot itch.anyways,coming to the issue.how did you try to flash rom while you got brick?which kernel you had?
Sent from my GT-I9100 using xda app-developers app
You were trying to change the look by flashing a kernel? I'm sorry, but that doesn't make sense. Also you really need to know which ROMs and kernel version you're on. There are ROMs compatible with siyah 4.1.5 and ROMs which are not.
Mention all (correct) details of your roms used and the kernel you're on. Maybe there's a solution there and someone will be able to point out if you've been doing something wrong. Dual boot is perfectly safe. I've been using siyah+ dual boot ever since the day I first rooted my phone and never had a problem.
Sent from my GT-I9100 using xda app-developers app
SGS2 Bricked on ROM 1 after downgrading from JB 4.1.1
Hi,
Sorry if i'm using the wrong terminology. If you hadn't guessed im pretty new to rooting etc and thought that changing the kernel also changed the theme/appearance. Anyway im currently running the following:See attachment.This only boots up on the 2nd ROM option. I cannot boot anything on the default 1st ROM and cannot even do a factory data wipe reset of the 1st ROM as CWM just hangs.
I Am Phooka said:
Hi,
Sorry if i'm using the wrong terminology. If you hadn't guessed im pretty new to rooting etc and thought that changing the kernel also changed the theme/appearance. Anyway im currently running the following:See attachment.This only boots up on the 2nd ROM option. I cannot boot anything on the default 1st ROM and cannot even do a factory data wipe reset of the 1st ROM as CWM just hangs.
Click to expand...
Click to collapse
My advice to you would be this:
1. Boot into recovery.
2. FORMAT cache, system, data and internal storage.
3. Boot into Download mode.
4. Flash an "all in one" OFFICIAL 4.0.3 firmware package using Odin. Place this in the PDA section and do not touch anything else.
5. Once it's finished flashing your device should restart and you should be good to go. With a clean, stock firmware.
Let me know if you have trouble
SGS" Bricked on ROM 1 after downgrade from JB 4.1.1.
Obagleyfreer said:
My advice to you would be this:
1. Boot into recovery.
2. FORMAT cache, system, data and internal storage.
3. Boot into Download mode.
4. Flash an "all in one" OFFICIAL 4.0.3 firmware package using Odin. Place this in the PDA section and do not touch anything else.
5. Once it's finished flashing your device should restart and you should be good to go. With a clean, stock firmware.
Let me know if you have trouble
Click to expand...
Click to collapse
Hi, Thanks for your help. I tried the above but when formating data it just hung and then eventually rebooted. I flashed the stock ROM anyway and now it just hangs at the Galaxy SII start screen, i even tried flashing it twice but that didn't help. I have also tried doing a factory data wipe from within the stock recovery after the flash but this still hangs and never completes. Is there a way of formating the data on the phone from within windows using a terminal emulator or something like that?. I have ROM Toolbox Pro on the device which has a terminal emulator as well if thats any good. For now i'll have to restore my nandroid backup I made this morning. mick
I Am Phooka said:
Hi, Thanks for your help. I tried the above but when formating data it just hung and then eventually rebooted. I flashed the stock ROM anyway and now it just hangs at the Galaxy SII start screen, i even tried flashing it twice but that didn't help. I have also tried doing a factory data wipe from within the stock recovery after the flash but this still hangs and never completes. Is there a way of formating the data on the phone from within windows using a terminal emulator or something like that?. I have ROM Toolbox Pro on the device which has a terminal emulator as well if thats any good. For now i'll have to restore my nandroid backup I made this morning. mick
Click to expand...
Click to collapse
he is saying go to stock rom by odin.i will give you a link where u can learn how to do it.i am from mobile right now.
Sent from my GT-I9100 using xda app-developers app
Tried stock rom. still wont boot
adilliano said:
he is saying go to stock rom by odin.i will give you a link where u can learn how to do it.i am from mobile right now.
Sent from my GT-I9100 using xda app-developers app
Click to expand...
Click to collapse
Hi, Sorry for the delay in answering i have been away for a couple of days. I flashed a stock rom with odin and it flashed OK and I got a green pass but when my android reboots it gets stuck half way through the install and then crashes and then never gets past the galaxy logo boot screen. I think the kernel must install OK though as after flashing the stock ROM i lost my dual boot option and the phone was bricked again. The only way i can get it working again is to enter stock recovery and install CWM zip, then install superroot & busy box and then flash siyah. This then gives me the dual boot option in CWM recovery where I can restore from nandroid and reboot into the 2nd rom. The problem only happens when i am trying to install a rom in ROM 1 slot (default) on siyah. Whatever ROM it is it never gets past the data part of the install.

[Q] Phone won't boot, can access download and recovery mode.

Ok there, guys.
Before I start, yes I'm an idiot, yes I'm a huge noob, no I don't know what I'm doing.
Basically, I have a SGS2 and I was trying to install Cyanogenmod 10.1.
I used Heimdall to (flash?) install ClockworkMod Recovery and it worked.
I realised that I hadn't put the Cyanogenmod .zip on my phone before I installed CWM.
I got up to rebooting my phone so I could transfer the zip but after the Galaxy splash screen nothing happened.
The screen just stays black and doesn't do anything.
I can access Download and Recovery mode so that's good.
I only have access to a Mac at the moment so I have to use the Heimdall command line.
If anybody could help it would be great, thanks!
jubsticles said:
Ok there, guys.
Before I start, yes I'm an idiot, yes I'm a huge noob, no I don't know what I'm doing.
Basically, I have a SGS2 and I was trying to install Cyanogenmod 10.1.
I used Heimdall to (flash?) install ClockworkMod Recovery and it worked.
I realised that I hadn't put the Cyanogenmod .zip on my phone before I installed CWM.
I got up to rebooting my phone so I could transfer the zip but after the Galaxy splash screen nothing happened.
The screen just stays black and doesn't do anything.
I can access Download and Recovery mode so that's good.
I only have access to a Mac at the moment so I have to use the Heimdall command line.
If anybody could help it would be great, thanks!
Click to expand...
Click to collapse
Put your forgotten .zip on an sd card put it in your phone. Boot to recovery and install. Then do full wipe and you should be good to go.
LSD Powered Time Machine.
gaosphappy said:
Put your forgotten .zip on an sd card put it in your phone. Boot to recovery and install. Then do full wipe and you should be good to go.
LSD Powered Time Machine.
Click to expand...
Click to collapse
How can I access my phone's storage through recovery/download mode?
Thanks for the reply, by the way.
Edit: Oops, sorry. Didn't read your reply correctly. Unfortunately I don't have a SD card. Is there a way I can restore my phone COMPLETELY to stock?
jubsticles said:
How can I access my phone's storage through recovery/download mode?
Thanks for the reply, by the way.
Edit: Oops, sorry. Didn't read your reply correctly. Unfortunately I don't have a SD card. Is there a way I can restore my phone COMPLETELY to stock?
Click to expand...
Click to collapse
Flash a stock rom and start from scratch. Get stock rom file from xda or sammobile (NOT A 4.0.4 ics rom tho.) flash via odin/Heimdall in download mode. it will boot up when done turn it off and reboot to recovery and do full wipe. redo your flash with missing .zip.
good luck
gaosphappy said:
Flash a stock rom and start from scratch. Get stock rom file from xda or (NOT A 4.0.4 ics rom tho.) flash via odin/Heimdall in download mode. it will boot up when done turn it off and reboot to recovery and do full wipe. redo your flash with missing .zip.
good luck
Click to expand...
Click to collapse
I flashed a 4.1.2 stock rom onto my phone but it still doesn't work.
I flashed the phone, it automatically rebooted, when the Samsung logo came up I took out the battery, went to recovery mode, wiped cache and full wipe, hit reboot and now it just stays on the Samsung logo, pulsing blue and what not.
I also did the same thing and instead of taking out the battery I just left it in there after the first reboot and the same thing happened.
How can I fix this?
Hum....I9100?
flash lsj (only phone, code abd csc).
Sent from the little guy

[Q] Bricked! Help!

Hey all
My phone was working great, everything smooth and awesome, but then i turned it off, and boot loop.
I tried reflashing my ROM, (ARHD) But that didn't work
Help!!
Have you tried looking at any of the solutions listed in any of the other hundreds of "Bricked" threads?
Obligatory "search" is your friend statement. If you can get into fastboot, if you can get into recovery, you're not bricked. Restore from your NAND backup, or flash your ROM again.
Like unremarked said, your best weapon is the search box
So you have:
1. Booted to recovery successfully?
2. Already tried flashing your ROM via TWRP/CWM?
seamarshall said:
Like unremarked said, your best weapon is the search box
So you have:
1. Booted to recovery successfully?
2. Already tried flashing your ROM via TWRP/CWM?
Click to expand...
Click to collapse
I can boot into cwm, but i can't mount the sd card for some reason.
xquantums said:
I can boot into cwm, but i can't mount the sd card for some reason.
Click to expand...
Click to collapse
As long as you get something anything on your screen, it can be fixed.
Maybe try flashing a recovery from fastboot
Sent from my HTC One using xda app-developers app

Categories

Resources