Hi,
I have a cracked screen, so I bought a bricked S2 off gumtree. I'm having a go at getting it to run again. So far all I know is that the previous owner was in the middle of flashing Odin, it said that the flash failed, and then he was unable to boot the phone any more. No powerup, no vol+home+power. No nothing.
The guy seems straight-up, I've no reason to suspect any more damage than reported. I've been in contact with him after the sale, and gave him a guilt-free opportunity to fess up in case he had done anything else.
I made a microUSB jig, and had a go with that, but no luck.
Is there anything else I can try?
--------
Secondary question (if I can't get the new phone up and running) - changing over the screens: would I dismantle both phones and move the screen from the new brick to my phone? or would I move the motherboard from the old/cracked to the new?
are you sure that you made e good JIG
if not, buy one
if it doesn't help and doesn't boot at all....it's dead
Related
Hello,
I reciently rooted my samsung galaxy s2. I tried a few roms so i could get used to the system or restoring etc. However i encountered a problem whilst having a peek at an alpha jellybean rom, where i noticed that my CWM app on the phone had vanished? I attempted the restore using the 3 button combo and found that i kept recieveing E: can't mount/ E: can't cache messages whilst on the restore screen. i could find my latest restore on my sd card however it wouldnt restore. I believe the CWM was removed from my phone which caused it to not work. I was then stuck in a bootloop. no matter what i done, boot to a stock rom via odin, try the different CF roms i and try to put CWM back on to the phone? I read a post on here from someone who had the same problem, who was told it looked as though there is a problem with the partitions. i followed a tutorial and used odin to put Latona 20110114.pit on the phone. it said i would get a blank screen once this has done and i needed to remove then place the battery back in the phone then put it into download again. This didnt happen!! I done as instructed and now my phone wont go into recovery mode, download mode or even boot loop. I fear i have completely bricked my phone so i am trying to use oneclick heimdall to sort it however my PC keeps saying i need admin rights to install it which i have.
Can someone please help me out. I am new to this so please go easy on me.
many thanks
If you have no signs of life from the phone, it's probably cactus.
You might as well try a jig (but unlikely to work; still try one tho). Only option is service centre & hope they can't tell/don't care you've been messing with it & fix it under warranty or JTAG repair by a 3rd party repairer, at your cost obviously; will be cheaper than having Samsung/an authorised repairer fix it if they refuse warranty service which they're quite within their rights to do.
edinsam said:
i followed a tutorial and used odin to put Latona 20110114.pit on the phone.
Click to expand...
Click to collapse
First result of searching suggests that's meant for the I9003. Good job.
HA
Hello,
Awe well then. never mind eh, whats done is done! Its totally bricked so i thought i would chance my luck by sending it back to O2 for repair. I was reading the only other way to get the phone running again was to take it to bits and hook it up for some stock flashing. so heres hopping they sort it!
lesson learnt!!!
Ok, so Monday I had my Galaxy set up with Dorimanx kernel 7.22 dual booting 4.1.2 RR (1st ROM) and SalmanROM V4.2.(2nd ROM). I decided to remove the 2nd ROM and went to dual boot options in Recovery mode to remove it, however the phone got stuck while formatting data. I Restarted the phone in Recovery and was able to do a backup but when trying to access the internal SD card I got the error can't mount emmc/.
After reading a bit here: [GUIDE] Fix an unflashable or soft bricked GSII (I9100G/M/P/T VERSION INCLUDED!) I found that my phone was soft bricked and had NAND rw corruption. I followed the steps but was not able to flash the recovery files or the kernel alone, I was only able to succesfully flash the bootloader but once I did that I tried the kernel again and had no luck. I decided to do it again and flashed the bootloader, Odin displayed it was completed and the phone rebooted, only that this time it didn't turn on.
Now my phone is basically dead, it doesn't turn on, it is not recognized by PC/Odin. I ordered a USB Jig which is supposed to arrive next week to see if that can revive it but looking around the web I'm seeing a guy selling an S2 for basically $100 dlls., the phone turns on you can hear the music when booting, rings when you call, only that the screen stays black. Seeing that my S2 might have a damaged motherboard this could help me fix it for less than what Samsung might charge me (I got the phone used so it doesn't have warranty)
My question is, should I wait for the jig to try and revive the phone? What chances do I have ? or should I get the spare one and replace the motherboard?
Thanks for helping!
USB Jig did not work, I will need a JTAG. Can anyone recommend me a good one? I've seen this one http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-ii-jtag-brick-repair/ seems reliable but I want a second opinion.
I have a SGH-I747M 4.1.1 Galaxy S3.
I used the Unified Toolkit and rooted/installed CWM, backuped and ready for a new ROM.
As I was installing this custom ROM (Pardus HD), and error popped up and it was aborted, (still in the CWM main menu)
but having only the said custom ROM zip file in the internal memory,
I figured I just shut down and download a fresh copy of the ROM.
and put it in an external SD card then power on the phone back into recovery.
Only thing is it wont power on anymore, the screen is just black, plugging in USB and computer just makes connected/disconnected noise.
(Devices say its "Qualcomm HS-USB DQLoader 9008")
Also tried taking out putting in the battery.
(I know my mistake is I never re-installed the backup) I've run out of ideas, please help.
I have a very similar problem. I had my battery checked thinking that could be the problem. My battery shows that is no good. I tried a new one and still nothing. I can't help but think if it were a missing program it would still come on at least. Lucky for me its covered under insurance. I'd still like to know what happened and if I could fix it.
I'd like to know too if I could fix it myself, other than ''the jig'' or a repair service. currenty trying to revive it still
edit: currently trying this Heimdall thing, goodluck to me...
Have you checked the battery? If I wasn't sending mine back on an insurance claim I would take it apart. I have a Motorola that has a fuse next to the battery under the back of the case. Seems dumb, I know but how could changing the rom "short" out my battery. Dumb again I always thought bricking was only being able to bring up recovery.
I think the battery is fine, as CWM was still running after the error.
That's pretty much what happened to me. Maybe we got to the same problem 2 different ways. Hope you get it figured out.
THIS IS GT-I9300 SECTION..
c'mon there was an stickie on top of this section for you..
HERE.. http://forum.xda-developers.com/forumdisplay.php?f=1705
Your problem is that you flashed a rom for gt-i9300 (International) and you have some U.S. variant of s3. That in most cases bricks the phone.
Probably time for a service center visit.
Hey guys
1) Restarted my phone today using CM10.1 from a very recent nightly (within the past week).
2) On restart, phone froze and got kernel panic.
3) Restarted into CWM and tried to do a restore to an earlier backup I had made.
4) Half-way through the restore, I got ANOTHER kernel panic (never had that before)...
5) Only things I could do with the phone after that was enter download mode...nothing else...couldn't enter recovery mode anymore.
6) Went into download mode and flashed this CWM-Recovery (http://forum.xda-developers.com/showthread.php?t=1118693) and followed the instructions to the letter.
7) Odin 3.07 hung on NAND Write Start
8) Tried using Odin 1.3, and it seemed to flash correctly. It says completed no errors.
Phone will now not even start and is completely unresponsive...pressing any combination of buttons will not start the phone, and the phone is not recognized in Odin anymore...did I just hard brick it? Any other ideas?
Thanks,
Elliott
Service centre. Although if you can have someone who does JTAG's have a look at it to determine whether it can be JTAG'd without you giving them any money up front (I.E you only pay them if it can be JTAG'd), try that first.
Thanks that's what I thought.
Also, try a jig if you can get one. In all likelihood won't work, but stranger things have happened & you have nothing to lose.
Yeah thanks that's what I plan on doing. Any idea what I did wrong, though? I don't want it to happen again if I get it working with a jig.
Impossible to say. Not sure why you flashed that nondescript kernel/recovery in that situation tho given it probably wouldn't have worked even if the flash had been successful (You would probably have ended up with bootloop given recovery was obviously 'broken'). I would have flashed stock with Odin (And that's certainly what I tell people in your situation on here to do because it normally works).
But flashing recovery rather than a stock rom probably didn't break your phone, put it that way, so you didn't do anything 'wrong' per se. Just remember if you get into a similar situation again, go back to stock via Odin & start again (re-root your phone/restore a backup, flash your custom rom/kernel again, etc).
If the jig works (and don't get your hopes up or anything, we're talking a 1 in 10,000 chance, and that's probably being generous), flash stock with Odin (you wont have much choice).
Well...brought it to a JTAG specialist today and he couldn't fix it either...says it's very rare and he's had 5 out of 80 S2's like this happen without being able to fix them...
Bummer. Motherboard replacement in that case. If the phone's under warranty, take it to a service centre & say as little as possible. You might blag it for a warranty fix. No warranty ? You can still have a new motherboard put in by a service centre (more expensive option usually), or you can source a 2nd hand MB from a 'donor' phone (one with a broken screen that's otherwise OK, etc) & either swap it in yourself or pay a local mobile repair shop to do it (usually cheaper option).
@ OP By following what you flashed I noticed the date, we're talking about a 2 years old thread, a lot have changed since.
Not sure that was what bricked your device but I get that panic mode.
The other thing that it comes to mind is nand corruption, which has been quite common these days with people running custom.
I'm with bungle there, the best recovery package is going back to stock and start fresh.
I, on the other hand, wouldn't accept the situation you are on, I would spend a whole week trying to get that phone to boot again, whether a second opinion on a jtag, a new jig, another battery or any other thread on here at xda.
If the device gets hot near the rear camera and it won't even charge nor get warm around that area dismiss what I just said and proceed with the mobo replacement bungle suggested.
And of course, if you did something else to your device and didn't share it please, come clean so others don't freak out by reading this.
Sent from...this is not even my S2
Hey
Nothing else was done to the device...just what I stated exactly.
I caved today and bought a BNIB S3 because I couldn't go without a phone anymore...
Thanks for the help, guys
Elliott
Hello,
I have a Samsung Galaxy S2.
After reading this post http://forum.xda-developers.com/showthread.php?t=2382579 I decided to root my phone.
So I went ahead and started with this step http://forum.xda-developers.com/showthread.php?t=1118693 because I was unsure if I had a kernel with the MMC-SUPERBRICK-BUG.
After I flashed CWM-SuperSU-v0.97.zip using Odin version 1.85 and after the phone rebooted it was stuck at the "triangle screen" for a few seconds then the display went black and I couldn't do anything further.
Up to this point the phone was still accessible in download mode (volume up, power and center button). I believe this is called "download mode". Sorry but I am a complete noob with rooting phones, etc...
So I panicked and took the phone to a repair shop (big mistake). The guy ran it in download mode then tried to flash something onto the phone (I think he used all 4 fields: Bootloader, PDA, Phone and CSC.
Then, in the middle of the operation, Odin froze when writing "setting up connection". Then the phone died ! pressing the 3 famous buttons does nothing and the phone just stays dead.
I had to leave the phone there as the guy said they will try to bypass stuff and try to connect to the CPU directly (sorry again if this sounds noobish). I did update my modem firmware and my computer BIOS in the past... but I guess this one was more complicated.
At the shop, they asked me to check again in 3 days. I am lost here. I don't know what to do anymore.
Is the phone hard bricked ? Should they bear all expenses for what they did ? I would bring back my phone and try something like this http://forum.xda-developers.com/showthread.php?t=1878255 or even a stock flash but I am afraid I cannot do that as the phone isn't even powering up anymore after they tried to repair it at the shop.
Any advice is appreciated.
Nope. You borked it. You tried to flash custom firmware to the phone & obviously failed spectacularly at it. Instead of trying to flash it yourself via download mode (which you could easily have done unless the NAND was borked), you paid them to do it. Sometimes flashes go bad. Sounds like that's what happened in this case.
Reading between the lines they sound like they're going to try & JTAG it (or have someone else do it). And if that fails I presume they'll change motherboards. You could always get the phone back & take it to someone who does JTAGs if that shop doesn't themselves.
MistahBungle said:
Nope. You borked it. You tried to flash custom firmware to the phone & obviously failed spectacularly at it. Instead of trying to flash it yourself via download mode (which you could easily have done unless the NAND was borked), you paid them to do it. Sometimes flashes go bad. Sounds like that's what happened in this case.
Reading between the lines they sound like they're going to try & JTAG it (or have someone else do it). And if that fails I presume they'll change motherboards. You could always get the phone back & take it to someone who does JTAGs if that shop doesn't themselves.
Click to expand...
Click to collapse
Yes I know I failed at it
Or maybe the shop technician is the one who broke it. At least when I had the phone with me I was still able to boot in Odin mode.
Do you think I could have recovered my phone if I had kept it with me and it was booting in download mode ?
I feel so pissed that I took it to that shop. I just wish I hadn't panicked and I had tried, instead, to fix it at home by asking for more help.
Anyway I still haven't paid them anything so far.
We agreed that they will pay for the motherboard because I brought in a working phone (that would power up at least). The owner of the shop was nice enough to agree that he would only charge me fees for installing new software on the phone (even if they have to change the motherboard) because he knows the phone was booting in Odin mode when I came in to the shop and his technician flashed the wrong firmware.
I also wrote down the board serial number so I can be sure they changed it (if they say they did that). So you are telling me the phone can still be fixed ? What does JTAG mean ?
Even if it is fixed I think I will be too scared to try and root it again. Unless I can understand in advance, step by step, what I need to do and what file version(s) I need to use.
Ok, I got my phone today in good working condition.
According to the shop, they had to replace an IC (I don't know what damaged the IC, I am assuming this happened when they tried to electrically jolt the phone) then JTAG it to get it to work again. They charged me a small fee (and they did end up bearing more than 50% of the expenses) because I brought in a phone that was booting in download mode and they take responsibility for what happened after that (flashing wrong files which caused the phone to completely stop booting).
Anyway, long story short, this was my first attempt to root a mobile phone and I learned my lesson.
I am running the following:
Model Number: GT-I9100
Android Version: 4.0.3 (which I will need to upgrade to 4.1.2 of course)
Baseband Version: I9100XXLPW
I know you will say read the sticky posts or the guides but the truth is, that's exactly what I did (you can see the links to the guide I tried to follow in my original post) and I still ended up failing at rooting/installing cyanogen on my phone right after installing Clockwork Mod.
The truth is I am scared to try again and mess up the phone. So this time I would rather be safe than sorry.
What can I do, this time, to safely root it and install a mod like Cyanogen.
Detailed steps are appreciated:
- Do I need to upgrade to 4.1.2 before rooting as 4.0.3 might have the superbrick bug ?
- How to backup the phone.
- Odin version to use, ClockWork Mod version to use, Cyanogen version to use
- How to connect the phone, how to reboot in download mode and all the necessary actions to avoid bricking my phone.
No spoon feeding aloud on XDA.better to read and learn how to do this and that but before you flash anything after learning how to do that learn how to fix it if it doesn't work. :thumbup:
andrewwright said:
No spoon feeding aloud on XDA.better to read and learn how to do this and that but before you flash anything after learning how to do that learn how to fix it if it doesn't work. :thumbup:
Click to expand...
Click to collapse
Fair enough, I figured I'd get that reply from someone and it's normal to be honest.
I decided not to try anything on my phone before I re-read the guides and be sure I know what I am doing.
I will also keep the phone running on stock firmware (after upgrading to JB 4.1.2) to check the battery consumption behavior which, I hope, will be fine since someone tampered with my phone's electronic components at the shop.