Related
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
keithgrobertson said:
Hi there,
I searched before posting this, but couldn't find anything for the Atrix...
Just wondering if anyone has seen/made a guide to replace the Glass/digitizer for the Motorola Atrix?
As to why I'm asking:
(If the image links don't work, you can find them as attachments to this post)
I've damaged the plastic around the glass (basically the housing, near the usb port) but I need to remove it from the digitizer...
I bought this: http://forum.xda-developers.com/attachment.php?attachmentid=572442&stc=1&d=1303199913
But as the ifixit teardown guide shows...
(http://forum.xda-developers.com/attachment.php?attachmentid=572441&stc=1&d=1303199913),
...When you take the phone apart, the glass is one with the housing.. Has anyone done this replacement of the digitizer or housing, if so, can you offer any suggestions, and what you used as adhesive to reattach the digitizer?
I've repaired the iPhone 3Gs and iPhone 4 before, both ranking higher in difficulty on ifixit's site, so I'm guessing the ATRIX should be a lot easier...
Anyways, any helpful tips or any guides would be greatly appreciated. I've already checked Google but no luck...
Click to expand...
Click to collapse
Try this http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/1
Or, this http://www.youtube.com/watch?v=TbR56jSplRs
Broke my digitizer and did the job myself using the youtube guide above. Just used straight up superglue to glue digitizer to frame. I put a bunch on the top and bottom and very little on the sides.
Amazingly the phone worked when i put it back together... for a while until I screwed up one of the ribbons by opening it a bunch more times. Be extra careful with these, especially the volume/camera ribbon. You can bend it pretty easily trying to slide it back into its slot.
Good luck.
NB: Theres places that will do it for as little as $90 in case you don't want to take the risk.
http://www.ubreakifix.com/
Thanks for posting the youtube link. I can't even quote the post because it involves an external link. The video was vague on details and the quality is crap but it did the trick.
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from amazon and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Metacat said:
My Arix got under the tires of a car (please dont ask how ) and only the digitizer broke, then i replace it with an OEM digitizer from ebay and now the proximity sensor is malfunctioning (Turns off the screen when im not near it or doesnt turns off when im near it), and there is a line of the screen that doesn't respond to tact. could it be the digitizer that came defective, or maybe it was the installation? oh, the other digitizer was broken and all but the light sensor was working fine and also the other thing. Sorry for my bad grammar.
Click to expand...
Click to collapse
I replaced my digitizer, and had the EXACT same thing happen (not the light sensor but the line in the screen that doesnt respond to touch).
Get a new digitizer, but get it from someone else.
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Metacat said:
That's what i feared, did you changed it back again afther that, and did it worked? and thanks.
Click to expand...
Click to collapse
No. I sold it and let someone else deal with it. Didn't have the time to replace the digitizer again. Too much of a hassle.
I just replaced a digitizer on an atrix... i didnt put any adhesive on it because there was what i thought was adhesive strips on the digitizer... but there's strips on the screen that doesnt respond, i heated it n tried reattaching the digitizer a few times n sometimes the home and back button will work, sometimes they wont... any suggestions? could the lack of adhesive cause this?
Menu buttons problem
if menu buttons is freeze till I block and then unblock my phone is it digitizer problem ?
what do you mean by " block/unblock" ?
Sent from my HTC Desire CDMA using XDA
He means lock/unlock.
Go the ifixit route!
Just went through 3 digitizers in my repair, and wanted to share my experience/caveats
I bought one digitizer from All4Cellular for $25, and the others with a 20% discount a few days later, for $20.
I installed
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Got the idea to move the LCD screen from another RepairUniverse YouTube video and a previous post here, and tried installing the digitizer from the front face of the phone. It was still a delicate matter to bend the flex cable so that it fit through the slot, and then re-position the LCD and align the sticky strips of the digitizer on the LCD and casing. Part of the digitizer worked this time - a 1cm vertical strip on the left fowled any attempt to touch icons or use a keyboard, so I thought I had damaged things again (doh!).
Hoping third time was the charm, I completely disassembled the phone using the guide in the 'ifixit' link, since a digitizer/case assembly was suggested in another thread. The rear camera just needs to be raised above the casing so the thin plate can move upward, and the LCD pops out easily if the sides of the casing are delicately pulled. The digitizer can be positioned easily and with minimal bending/twisting of the flex cables.
When reconnecting everything the third time, I noticed that pressing down on the front camera / digitizer connection *with the rubber boot in place* didn't pass when pulling the connected assembly upward. So I pulled the rubber boot out of the way and snapped the camera / digitizer connection firmly, then re-inserted the boot. A loose connection might have been the culprit for the nonfunctioning part of the digitizer in the second test.
@MrSaba - I had the same issue with capacitive buttons - perhaps because the screen senses touch and disables those buttons. Replacing the digitizer solved the issue
trouble
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
drZeT said:
Hello friends,
Here's my story - broke a screen, as usual slipped from my pocket. though broken, digitizer worked fine. after replacement with new one (digitizer only) - no luck it didn't work. bought a new one, this time with a plastic part around it to avoid damage to it's cable. after careful repair no luck once again - does not work at all. downloaded a testing app (i was able to remote control the phone with a piece of soft called androidscreencast), everything is ok, except digitizer. checked and rechecked all ribbons and connectors 10 times, nothing seems to be broken or twisted.
what's your opinion, is it worth buying third one ? what part of my repair went wrong ?
thanks
Click to expand...
Click to collapse
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
jjwatmyself said:
Not all digitizers are created equal. The ones that ship with the red stripe on the backing are junk. Spend more money and yes buying with a frame is key. Did you try reinstalling the original screen or did that ship sail already?
Sent from my MB860 using Tapatalk 2
Click to expand...
Click to collapse
The first one was with the red stripe indeed, from china. The one with a frame came from UK, "used but tested OK". original screen is gone - tore off flex cable while removing.
Well, update...
2 screens bought on eBay were BAD. Had to wait full month for authorised motorola service to change the digitizer. Must say though that both merchants on ebay refunded, no questions asked. Lessons learned - pay more, wait longer, never give up
DrJCFitz said:
the first using the RepairUniverse Youtube 'how-to' method, and had a heck of a time threading the flex cables through the slot. Bent/twisted it too much, and nothing responded on the touchscreen, so I read some forum posts on how fragile they were, and regarded that as user error.
Click to expand...
Click to collapse
What I noticed on their video was that their folded digitizer connector magically unseats itself during the disassembly transition. I had to pry mine off based purely on guesswork and think I might have broken the flip-chip that is stuck onto the frame with double-sided tape. Like yours, my touchscreen doesn't respond at all, despite there being no cable tears. I'm going to try and re-heat that flip chip and maybe get the connections to work again (doubtful).
To anyone else out there attempting this... when you go to remove the touchscreen, HEAT THE CONNECTOR so that you can gently pry it out!
Bad screen I got 3 before it worked its fine now if old one partially works new one doesn't screen is junk took mine apart several times to figure out screens were junk...guess they felt sorry for me give me my money back plus free working screen.from amazon
Also that lock clamp u mentioned first video I watched didn't show unlocking that I just pulled it out and pushed back in it was the 2 screen that I figured out it needed to be pryed loose by the white clamp but guess I didn't damage it..
Sent from my HTC One X+ using xda premium
I have just put in my second digitiser. The first was one had a red stripe, which was junk, the second on I bought had the plastic round the edge and the digitiser.
I put it in and it worked fine no dead spots at all. Then 12 hours in it started to stop working intermittently. Then 24 hours after that while on charge its dead again. I reflashed notattrix and still nothing. I've confirmed all the ribbon connectors are firmly in place and everything looks right.
Any ideas whats wrong?
thanks
Jonnym
I can't find any info on this, but it looks like it could be tricky to replace. I cracked my glass by dropping it onto stone, still works OK. You can pick up digitisers pretty cheap on ebay (£20 UK) but does anyone know how to replace? I read that they can be glued to the LCD?
Thanks
Google for the fixit website, if someone has done it there will be a tutorial, or you could follow the guide on here to upgrade your sd card....only because you have to take the phone fully apart. You need to check if the lcd is glued or like the iphone 4 resin. If they are a sealed unit you'd be better off getting the lcd/digitizer combo on ebay. trying to separate an lcd from the digitizer is asking for trouble imho.
I have ordered a digitiser, really hope the digitiser is not glued to the LCD, there is a big price difference. I'll let you know how I get on.
I bought a Mozart with wrecked digitizer and also want to repair it. The digitizer is on its way, so in a week i could tell you how difficult or maybe easy it is.
If you are faster, please post your experience.
I found this thread on xda.cn, and it seems that the lcd isnt glued on the digitizer, so lets hope so
hxxp://xxx.xda.cn/newshow.php?snid=2167
EDIT: sorry cantpost links, so must change the x's to t's and w's
I have got my digitiser now, looks brand new. Just need to find the time to replace, might upgrade the SD card at the same time.
Done
I did this with Andy's guide to help: http://lifeinthefastlaneok.wordpres...-7-mozart-sd-card-memory-upgrade/#comment-225
I used this guide to replace my digitiser (the glass) which I smashed. The good news is that the digitiser is not stuck to the LCD at all. I just bought a grade A digitiser off ebay for £20 which was pretty much perfect - glass was perfect with a couple of small marks on the back case, but basically like new.
There were a couple of differences to this guide:
- Had to replace a speaker type thing at the top of the digitiser that was not present on the new one. Came off quite easily, just stuck in.
- Had to remove the USB port of the old case back (if you are replacing that too) but that was just a couple of screws
- You dont have to split the PCB off if doing this, you just take off the black clips to take it apart and then remove the orange ribbon cable, it is a little tricky to get the new one in but OK.
I now have a phone as good as new, I didn't replace the SD at the same time but probably will do at some point when I can stand loosing all my data.
Found time today to replace the digitizer. I also used Andy's videos for instruction. And it's really not that hard. Pretty easy for someones first mobile phone repair.
Well done, I would add for anyone else needing to do this, be very careful not to touch the inside of the digitiser or the LCD when you have it apart! Also have a glasses cloth handy for removing any dust particles just before you put it back together.
I do have one strange thing however - before I had intermittent issues where I could not slide the screen up when locked for 10 seconds or so. No I have a slightly different issue when unlocking - it doesn't always let me press on the right hand 3 numbers on the PIN screen! So it seems the unlocking issue some people have is due to a hardware issue. My digitiser was second hand so I might ask for a replacement, but I can change my pin so that it is not an issue.
My Mozart touch-screen hardly works at all plus my wife's Mozart has a cracked digitizer glass (still working fine).
So silly me I took the plunge and ordered three cheap replacement digitizers via eBay (from Hong Hong). They arrived today and all are s**t useless.
When I opened the box I smelt the rat when I spied the HTC logo on each was blanked out on the outside of the plastic zip-lock bags (with what looked like black felt pen), plus each glass has minor blemishes/scratches. Comparing each with the digitizers I removed from my and my wife's phones, they have a different design of ribbon cable conductor layout plus there are indications the plastic moulding isn't as well finished in a couple of places. Either these are factory rejects or knock-off copies. Lesson learnt :-(
Anyway, I now need to buy genuine HTC parts.
Any pointers toward reliable sources appreciated, thanks.
KJ
I have bought some off ebay. The problem is that these are almost always from returned Mozart's which may well have been returned due to non responsive screens, which seems to be a very common problem.
I have had 2 off the same chap now, one is OK but not perfect, the other one didnt work at all.
I would just keep returning them until you get one that works.
Sometimes you will find new combined digitiser/LCD's on ebay too, these would be a better bet but cost more.
Can someone who as changed a screen on this phone using Andys guide, please tell me how easy or hard it was, and how long does it take??
And would be grateful if someone could give me a link to the correct digitizer for this phone....
I am in the UK and have been qouted 50 pounds at a phone shop for the to supply and fit screen...
Did you see my post?
There were a couple of differences to this (Andy's) guide:
- Had to replace a speaker type thing at the top of the digitiser that was not present on the new one. Came off quite easily, just stuck in.
- Had to remove the USB port of the old case back (if you are replacing that too) but that was just a couple of screws
- You dont have to split the PCB off if doing this, you just take off the black clips to take it apart and then remove the orange ribbon cable, it is a little tricky to get the new one in but OK.
The most tricky thing for me was getting all the dust off the LCD and the digitsier, as soon as you get it apart things start sticking to it like crazy. Have a clean glasses cloth around.
It takes about an hour on your first go. The main thing is to get the orange ribbon cablle in fully, it can be tricky - you need to get a good grip on it (fold it a little) and push it home quite hard, otherwise you get it all back together and find it doesn't work.
I have had 2 dodgy screens off ebay, £50 sounds OK if it is a brand new original HTC screen.
Or just search for 'htc mozart digitiser' on ebayt there are loads.
hsclater said:
I have bought some off ebay. The problem is that these are almost always from returned Mozart's which may well have been returned due to non responsive screens, which seems to be a very common problem.
I have had 2 off the same chap now, one is OK but not perfect, the other one didnt work at all.
I would just keep returning them until you get one that works.
Sometimes you will find new combined digitiser/LCD's on ebay too, these would be a better bet but cost more.
Click to expand...
Click to collapse
Thank you for that. A close look at the ones I bought from china I'm sure now are removed from phones with faulty digitizers, then repackaged as new. One of the three had significant dust and dirt on the inside of the digitiser screen. I've requested a refund via PalPal disputes.
I've ordered some digitizers from ecell in the UK. I'm led to believe by them that these are genuine HTC factory supplied spares.
KJ
I just replaced my 4th screen (1 broke, 2 dodgy).
This one is perfect - as new condition and works perfectly, my last one was not responsive in some situations e.g. lock screen.
This is the one I got (UK)
http://www.ebay.co.uk/itm/130498971267?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
Of course, your mileage may vary - some are probably good, some not. Replace it, if it doesn't work ask for another, etc.
My new digitizers arrived today from the uk. Horray they are genuine HTC spare parts properly packaged. The downside is they don't include the frame the glass sit in and is adhered to.
So I watched the official HTC Mozart disassembly video on youtube to see how to remove the existing digitizer glass from the frame - got it apart ok after heating the unit to soften the adhesives but it didn't come away entirely cleanly i.e some of the adhesive foam broke away and was left on the underside of the glass.
So... check on eBay and found sellers selling refurbished screen frames ready for a new glass to be attached.
Will update on progress once they arrive.
KJ
just ordered my digitiser today... wish me luck...lol
poolielad said:
just ordered my digitiser today... wish me luck...lol
Click to expand...
Click to collapse
Well I am now buzzing... have just changed my screen at it works perfect.....
£50 they wanted at the shop...it cost me £13....
Just to let you know how easy this is to do........If I can do it, anyone can..
Did anyone find a reliable supply in the end? I just cracked my digitiser so looking to replace it...
--edit--
Also, how much have others paid? Don't want to be ripped off for some sub-standard part.
Hello everybody,
I m trying to replace the digitiser of a HTC Mozart too.
It is really easy to do, even the part where you have to take off the digitiser from the plastic frame.
But I have an issue, it is the second digitiser I am using ( from the same ebay shop ) and the digitiser is working inverted vertically! Really strange but it is like that.
As the mobile phone is started up, when I push on a left buton, it push on a right button ! On the key board, when I press on "P" it press on "A" ( i m using an Azerty layout, I assume it should be "Q" on your layout ).
It is really anyoing of course.
It is the second screen I received from the Ebay shop and same issue, I don't think the problem come from my side, but I just want to ask to you all if somebody have an idea or the same issue once.
fx.lagwagon said:
Hello everybody,
I m trying to replace the digitiser of a HTC Mozart too.
It is really easy to do, even the part where you have to take off the digitiser from the plastic frame.
But I have an issue, it is the second digitiser I am using ( from the same ebay shop ) and the digitiser is working inverted vertically! Really strange but it is like that.
As the mobile phone is started up, when I push on a left buton, it push on a right button ! On the key board, when I press on "P" it press on "A" ( i m using an Azerty layout, I assume it should be "Q" on your layout ).
It is really anyoing of course.
It is the second screen I received from the Ebay shop and same issue, I don't think the problem come from my side, but I just want to ask to you all if somebody have an idea or the same issue once.
Click to expand...
Click to collapse
Mate, I had the same problem. However it seems no one was able to help me either.
I also purchased a digitizer from Ebay for my Mozart - the exact same inverted issue occurred with me. I wasn't able to find a solution.
I'm in Australia with a T8697 model. The digitizer I received from Ebay had a circle around the windows button at the bottom - This was not on my original screen.
In the end, I purchased a digitizer from an Australian business. Cost double the Ebay digitizer did, so I hope it works... Haven't received it yet, but I'll let you know when I put it in.
What model Mozart do you own?
Anyone done this? My 800 fell onto concrete and the screen is shattered. It still works perfectly but obviously the screen is shattered.
They sell the glass on ebay for £10, or the full screen for about £70.
I asked in my local market stall and they said £40 for the repair. Not sure I trust them though, Another said £120 but for the full screen.
Is there somewhere I can send it to? I'm pretty clumsy so I don't really want to try and repair myself...
Glass and lcd are glued together and you can't change them sepparately. Safest way is to buy lcd+glass module together. You can change it by yourself, its easy. There is one perfect video on youtube (i think le55ons made it), so you can give a try.
I have done both, there's a number of instruction videos on Youtube. I'd replace the whole screen, takes 5 minutes and is very easy to do.
Just be very careful, it's relatively easy to mark the borders of the case in the process.
Sent from my Lumia 800 using XDA Windows Phone 7 App
Mine was broken too, went to Shenzhen to buy a new one for RMB150 (US$ 20 or so).
Change according to this video was easy: http://www.youtube.com/watch?v=xCU2PWiq0Kc
One problem was that my phone was totally discharged, so it was difficult to check whether the screen worked. But the shop had an open Nokia N9 which uses the same screen. So far so good.
A few hours later when I was back home of course then glass came of the white plastic frame and was hanging loose. I fixed that with double sided tape. Seems to work just fine, so no further action for that issue.
The screen seem to have dead spots. Sometimes. Sometimes not. Would be good to have paint App to check exactly where.
Yesterday at one stage the screen flickered like mad for a moment. But today no issue at all.
I have ONE question: What is the 2nd, small, flex cable for? In the shop they told me it's no use. But must be there for some reasons.
PS: a screen image I just took. I used a paint app to find the dead spot. I wonder if the LCD is defect or if this is an connection issue. I highly recommend to get a paint app to try that when you do a LCD replacement.
Update: after one more disassembly and reassembly the LCD has no dead spots and works fine. I am not sure what the smaller flex cable is for, I presume it's the light sensor.
Update of of the update: the dead spot is back. I presume the flex cable has a broken track that was temporarily connected last time. Seems that's hard to fix. Need a new LCD then.
Hello,
My phone has fallen today from my hand, and ever since the touch screen is unresponsive. It fell on the back, no visible damage to the screen. until then I had no problems with it so I doubt this is a digitizer problem. The phone had a hard case (always falling apart when I drop it) and a screen protector. All of my hard keys are working, but the soft ones (at the bottom of the screen) are not.
When I press "power", the menu seems to be stuck on the sound/silent options,with no ability to go to recovery, for example.
I tried removing the screen protector and playing with the battery but nothing is changing.
I am studying abroad now so I have no extra money to buy a new phone or any knowledge of a proper place to check my phone. A lab I contacted offered me a new touch screen for 200 pounds and wouldn't offer anything else.
I am lost, please help me.
I got an atrix to dropped on living room carpet done the same thing it created a dead spot in digitizer there is one ribbon connection to the touch screen digitizer so if part of ur screen works it's still most likely connected to the ribbon new screen is 40 bucks or so Google atrix4g digitizer tear down replace. touchscreen they sell the part to.on youtube here USA 100 us they fix it I fixed mine if u want I can find the link to it..
http://www.youtube.com/watch?v=grqz-3LdIEk&feature=youtube_gdata_player
Sent from my HTC One X+ using xda premium
Hello,
I'm desperate for some help. My girlfriends Lumia 920 got a cracked glass the other day, so I ordered a brand new OEM digitizer and adhesive and fitted it yesterday. All seemed well. Anyway last night we noticed that the soft keys don't light up anymore.
I assumed they scavenged light from the LCD screen but maybe they don't? Are they on a connector? Are they LED's? Has anyone else made this mistake before and knows how to rectify it, or is it a defective digitizer
Any help?
same issue
I have the same problem , mine worked fine then after replacing the glass/digitizer the touch and the lights at the bottom don't work. with the first one I thought it was bad , so they sent a second one. it does the exact same thing . so either the phone got messed up or maybe the replacements use a new chipset that does not jive well with the phone .if anyone needs parts for their phone I will part this one out. I got a new one from a pawn shop for $150 so it was not worth replacing the whole chaise to fix it ($99 online) . the digitizer/glass is brand new , maybe it will work for someone else and the battery, camera and lcd work fine as do all the buttons and charge ports.