Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Try to hard reset. Hold down the power button for at least 30 seconds. On devices that support it, the screen will turn off and the device should begin to cold reboot. A cold boot is where a device starts up from a power-off state. If that doesn't work you might have to test just how "nonremovable" their battery is and disassemble your device. If there aren't wires coming from the battery that are soldered to the phone's circuit board then it should be removable.
Hello to everyone,
I have the same GO phone. Do not try to open it (with purpose to take off the battery). To connect that phone in preloader mode just press volume up and then connect it in your pc. If you have the correct usb drivers, SP flash will find your phone.
I have done it and it worked for me. I have rooted my GO N1-y and I have used SP flash to unbrick my phone (I faced a problem with SP flash v.5.1352.01 and as a result I bricked my phone) using the official ROM. I did it with SP flash v.3.1320.0.174.
So, please give any feedback in case you find a custom rom for N1-Y.
Be good!!
thanasisvas said:
Hello to everyone,
I have the same GO phone. Do not try to open it (with purpose to take off the battery). To connect that phone in preloader mode just press volume up and then connect it in your pc. If you have the correct usb drivers, SP flash will find your phone.
I have done it and it worked for me. I have rooted my GO N1-y and I have used SP flash to unbrick my phone (I faced a problem with SP flash v.5.1352.01 and as a result I bricked my phone) using the official ROM. I did it with SP flash v.3.1320.0.174.
So, please give any feedback in case you find a custom rom for N1-Y.
Be good!!
Click to expand...
Click to collapse
I'm on my phone but I have another thread where I've discussed my many rom uses on the N1-Y
I've just found what I think is the best rom.
It's actually made for the Xolo Q1000s (the q1000s plus is pretty much a rebranded go n1y)
http://www.xolo.in/xolocare/software-update?page=3
If your try to Flash it via cwm it'll give an error.
I used 7 zip to view the archive and I edited it so that it never checked build.prop.
Flashed fine and is working great.
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Im not sure about your device, but i believe if your battery is not removeable, there will be a way to turn off your phone.
try pressing volume up and power until it vibrates 3 times, if its sony then this will work, try other button combination too
Try this : press volume up + volume down + Power
it work
MrMaddTraxx said:
Try this : press volume up + volume down + Power
Click to expand...
Click to collapse
I have mtk a device with a non-removable battery and I tried SEVERAL thing nothing works the dvice wase break dead then i tray these
prese up volume + down volum + power buttons and hold down and
i clique download in spflash tool
HaniAnis said:
I have mtk a device with a non-removable battery and I tried SEVERAL thing nothing works the dvice wase break dead then i tray these
prese up volume + down volum + power buttons and hold down and
i clique download in spflash tool
Click to expand...
Click to collapse
Well if you read the previous reply you should've noticed it was that combination to turn the device off.
I don't know what kind of problem you have so I have no idea how I could help you unless you say so
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Listen
your phone is rebooting but not showing on the screen
so what you need to do is
just try various combination like
vol up and vol down
vol up and power
vol down and power
and try this combination and keep pressing the button
and connect device to pc
and you will get the error that device power up too early
and the reason for the error is
reboot of device but no display on screen
so just try and try until your pc detect device and flashing starts
and believe me this the correct method
because i have repaired my phone with same method and i am sure because it worked for me three times
so keep trying the combination and at a moment your flashing tool
will start the flashing?
:fingers-crossed::fingers-crossed:
Give a LIKE :good::good:
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Hope my solution will help
i have an old phone hesens HE-F4 i insert sim card (GSM) and it displays no UIM card currently all the relevant apps of messaging internet and calls cannot be accessed how do i make it work
Hello everybody!
Searched all the threads but none seems to cover all my problems. I'm newbie here so i'd need detailed help.
So, what do I have? I have P768, came to me like this for 20 euros with problem that on every boot it says "Security Error". I know that this one is not strange to you. I've installed Mobile Support Tool and LGMobileDriver_WHQL_Ver_4.0.3. When I go to Options > Upgrade Recovery (of course i switch phone to S/W upgrade mode - VolUP + Power button when inserting USB), but phone not seems to be detected. Also, it is not showing up when connected via USB in device manager. I had antivirus, tried (known to me) everything - but no luck. So, I am thinking about restoring phone to it's stock firmware.
Any help, suggestion, link to other thread would be welcome!
This is my first post.
Best wishes from Serbia!
nebojsha89 said:
Hello everybody!
Searched all the threads but none seems to cover all my problems. I'm newbie here so i'd need detailed help.
So, what do I have? I have P768, came to me like this for 20 euros with problem that on every boot it says "Security Error". I know that this one is not strange to you. I've installed Mobile Support Tool and LGMobileDriver_WHQL_Ver_4.0.3. When I go to Options > Upgrade Recovery (of course i switch phone to S/W upgrade mode - VolUP + Power button when inserting USB), but phone not seems to be detected. Also, it is not showing up when connected via USB in device manager. I had antivirus, tried (known to me) everything - but no luck. So, I am thinking about restoring phone to it's stock firmware.
Any help, suggestion, link to other thread would be welcome!
This is my first post.
Best wishes from Serbia!
Click to expand...
Click to collapse
first install fastboot drivers using this thread
http://forum.xda-developers.com/showthread.php?t=2119090
then search fastboot script by lelus ,
best way to recover soft brick phone
http://forum.xda-developers.com/showthread.php?t=2292828
Install stock jelly boot img , recovery img from fastboot for p760.
best of luck
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.
Hello!
My phone, Acer Liquid Z630s, recently had a problem and ended up shutting off as soon as it boots up. I turn it on, the Acer powered by Android white screen shows up then immediately shuts off. What was the problem here?
I couldn't access recovery mode either because it would also show up the same thing above then shut off immediately before it can even reach the recovery mode menu. But I could plug it in directly into download mode through SP Flash Tools because the phone vibrates when I hold down the volume up + power buttons (aka the recovery mode combination which was I think also the download mode combination). I downloaded the correct stock ROM off the Acer website (MT6753) and flashed it. The ROM was successfully flashed. But when I turned it on the screen lit up but it was just a blank black screen. It was lit up, but it was just dark black. I tried to wipe the system and flash the ROM again and at the end of the process, an error message appeared and I looked up the error code and this was exactly it:
"Error 6104
Message: BROM ERROR: S_SECURITY_SECURE_USB_DL_DA_RETURN_INVALID_TYPE (6104), MSP ERROR CODE : 0X00
Meaning: Wrong flash settings or firmware
Solution:
Ensure you set the correct Download-Agent in SP flash tool and are using a firmware for your exact model
Go to Options > Option > Connection > USB Speed > Full Speed
Go to Options > Option > Download > Untick DA DL All with Checksum"
I did what the solution told me, and as I tried to flash the ROM again, but I couldn't turn on my phone anymore. The volume up + power button combination no longer produces a vibration, and when I plug it into my computer it gets detected as a MediaTek USB Port (COM6) but SP Flash Tools no longer detects my phone and gives off this error:
"Error 0x13BE
Message: S_DL_GET_DRAM_SETTING_FAIL (0x13BE)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash"
I don't know what to do at this point. Is it beyond salvation? But my phone still gets detected by my computer and it still produces the sound when you connect a device through the USB ports. Help me please.
Thank you in advance.
Hi , flash this firmware and in Sp Flash Tool set to Download only !!! When you Do Format + Download you lose your imei !
https://drive.google.com/uc?id=12CdmQaP8wi52RZO4jvjSikTWi2l4I1ZN&export=download
Teddy Lo said:
Hi , flash this firmware and in Sp Flash Tool set to Download only !!! When you Do Format + Download you lose your imei !
https://drive.google.com/uc?id=12CdmQaP8wi52RZO4jvjSikTWi2l4I1ZN&export=download
Click to expand...
Click to collapse
Hi there Teddy. Maybe you could help me. I was actually trying to make use of the same thing. SPFT. i flashed the stock rom. i tried rebooting it. seems that it has been bricked. I am using Starmobile Up Prime.
lexpizarro said:
Hi there Teddy. Maybe you could help me. I was actually trying to make use of the same thing. SPFT. i flashed the stock rom. i tried rebooting it. seems that it has been bricked. I am using Starmobile Up Prime.
Click to expand...
Click to collapse
Hi, If you flashed right stock firmware for your device correctly, your device it should not be bricked so I thing your flash file are not good.
Explain me what did you tried and which file you flashed?
Please help, a few days ago my phone decided to stop working for no reason, so I thought it was a ROM problem(I was running Android Pie AOSP Extended). So I reset it, after resetting it the phone was stuck at the LeEco logo, so I decided to use the 9008 mode flashing it, but no matter what I do it always come up with the error Download Fail:Sahara Fail:QSaharaServer Failrocess fail
So I don't know what to do, please help.
Did you tried flashing Twrp first in instead of qsahara sometime they give error
They show error also when partitions are messed up so may be u changed partition settings
So try installing Twrp and rewriting partitions then use a pendrive and mount it in Twrp and install a simple room for example AEX and try to boot otherwise try side loading the rom
If u r possible to boot into twrp format device and install any ROM zip through pendrive
I cannot even exit 9008 mode, the phone is completely dead with no respond when pressing any button combination, but it shows up as Qualcomm HS-USB QDLoader 9008 when I plugged in to my PC, and it also doesn't show up when using the ADB devices command. And thanks for replying
Can you add photos of what error it is showing when trying to boot into fastboot mode
https://drive.google.com/file/d/12jmHM0f50WFMMXeeZWxLq9LkdAg6magp/view?usp=sharing
This is the error it is giving me while trying to unbrick it, and the phone seems to be charging since my charging block is heating up.
MrNotJeff said:
https://drive.google.com/file/d/12jmHM0f50WFMMXeeZWxLq9LkdAg6magp/view?usp=sharing
This is the error it is giving me while trying to unbrick it, and the phone seems to be charging since my charging block is heating up.
Click to expand...
Click to collapse
Ok, first, dont give up, 2nd have you put phone into qfil mode as program told you? 3rd check if inside this zip is not 2nd zip, some packages are "double zipped".
MrNotJeff said:
https://drive.google.com/file/d/12jmHM0f50WFMMXeeZWxLq9LkdAg6magp/view?usp=sharing
This is the error it is giving me while trying to unbrick it, and the phone seems to be charging since my charging block is heating up.
Click to expand...
Click to collapse
I had a practically the same problem with Xiaomi Redmi Note 5 Pro (Chinese model)
Inside the zip file there is a file (or two of them) responsible for uploading the ROM. It first sends one of those files and the Qualcomm loader puts it in RAM and boots that file.
If successful, the upload continues, but if that file is wrong, it will not boot it and will not load. So the zip file you have may not be for the exact model of your phone. Try to find another one, maybe a different version...
Hope this helps.
Sent from my GM1900 using Tapatalk