Related
Hi, It's only been a day since I got my new i9100 and I've already managed to stuff it up and get out of my depth. I'd be grateful for any help or advice. I've done many searches and not found anyone with a similar problem.
Basically my problem is that my phone has corrupted firmware and whenever I connect the phone to power it goes into the mode with the little symbols showing a phone connected to a computer (I'll call that emergency mode). I know I can recover it from that mode with Kies, Odin, or Heimdall, but unfortunately it turns off whenever I disconnect it from power (apparently both my computers' USB power isn't enough to keep it on). I've left it connected to power overnight to charge (in emergency mode) but the same thing happens. I don't know of a way of connecting power without it entering emergency mode, in case that might help the battery to charge (assuming that's the problem). I am fairly sure the battery is flat, because if I put the contacts on my tongue I do not feel any tingling sensation as I usually do with a charged battery.
At this point my only idea is to splice 2 USB cables so that I can use mains power and connect it to a computer at the same time. I'd obviously prefer not to resort to that. Any Ideas?
What I did before, details:
I have an unbranded version of the i9100 sold by mobicity in Australia, no network locks or anything. First thing I did was to install Samsung Kies on my computer and check for firmware updates (It was originally running Android 2.3.3, I don't remember the build numbers). Kies told me that an update was available, so I told it do do its thing.
On the first attempt the phone rebooted into download mode and then Kies stopped responding at 0% and eventually said the update had failed. I eventually pulled the battery and when I put it back in the phone booted back into its stock firmware - no damage, but no update.
On the second attempt it booted into download mode got to 8% and stayed there for about half an hour. At this point I had to leave it, and when I got back the bar was on 12% and it said it had failed. After power cycling it was in emergency mode, which is as far as I got.
My previous phone is a Blade and I've flashed it to oblivion and recovered from all sorts of problems, but I've never had one like this before. Apologies if this information is already somewhere else, I did make an effort to find it.
What was your battery percentage before the flash, a full update usually takes about 5 to 6 minutes, if your battery is too low, it may not go through. Also you should get rid of Kies or at least make sure it is not running at all while you are using Odin, Odin should show a yellow block once it has detected your device in download mode, but Kies running at the same time can cause issues
Also, you should try to charge that battery if you are of the opinion that it is running low on juice, I don't have the expertise, but a simple test is to charge the device while it is powered off as I do not think the phone charges in Download mode, once it is charging, you should see a large battery icon with some dots above it that indicates it is charging, if you don't see that, it probably isn't charging, maybe because the firmware flash failed, I really don't have the expertise to say for sure, if the battery isn't charging, then you should buy an external charger, unless you believe yourself competent enough to do it by splicing wires.....
Also, you should read this thread HERE there is guide on flashing official firmwares among other things, have a read, charge your battery and all should be well
This thread HERE may also help
There was plenty to do the flash (about 50%). I managed to solve the problem by borrowing a charged battery from my rather amused friend who also has an s2 and following the instructions in that thread for recovering from a soft-brick (My battery was indeed flat). I guess now I won't have any illusions that using Kies is safer than anything else...
Thanks for your advice anyway.
Hi!
I know that are simillar threads about this, but none of them have the answer to my problem. I read them all.
As many others, my Galaxy S 2 started to give that error after the upgrade to ICS (in my case, I did it because my phone sent me the "alert" directly, not because I tried to upgrade it through Odin or similar).
My problem now is that the phone is not even detected by my computer in Download Mode, If I remove the battery for 10 minutes and add it again, it does show like if the battery ran out of charge and does not start, if I plug it to the wall charger then show as charging and then can start it, but the "charging suspended voltage too high" message show every 20 seconds.
I tried to clean the usb with a toothbrush, tried also with the "knife method" but nothing of that helps. I would like to even downgrade the OS to a 3.x version, but can't make the computer recognize the phone in Download Mode. Any help would be appreciated.
I drove myself mad chasing this one a couple of weeks ago, it does indeed seem to be a problem with the connection between the USB plug and the phones mainboard.
I did find a post by a Samsung engineer in which he claimed it was a common problem and that he was seeing 3 or 4 a day.
I was lucky in that mine was solved by gently pushing the male internal connector gently forwards (upwards if the phone is on its back)
If you think logically, a usb/mainboard connection problem does make sense, in as much as there are so many differing symptoms and the claimed successes by cleaning, I would guess in these instances, the cleaning has in fact, simply moved the connector back into position.
This is a pretty poor show for Sammy, there seem to be more and more S2's failing in this way as time goes on, my own phone has only ever been charged in the Samsung dock, and still fell foul of it!
I would give repositioning the connector another try, pull the battery and use a wooden toothpick or similar, I used a fruit knife, but wouldn't recommend it. If you cant get it back in shape, I'm afraid you will have to send it back to Samsung
R
JorgeC said:
Hi!
I know that are simillar threads about this, but none of them have the answer to my problem. I read them all.
As many others, my Galaxy S 2 started to give that error after the upgrade to ICS (in my case, I did it because my phone sent me the "alert" directly, not because I tried to upgrade it through Odin or similar).
My problem now is that the phone is not even detected by my computer in Download Mode, If I remove the battery for 10 minutes and add it again, it does show like if the battery ran out of charge and does not start, if I plug it to the wall charger then show as charging and then can start it, but the "charging suspended voltage too high" message show every 20 seconds.
I tried to clean the usb with a toothbrush, tried also with the "knife method" but nothing of that helps. I would like to even downgrade the OS to a 3.x version, but can't make the computer recognize the phone in Download Mode. Any help would be appreciated.
Click to expand...
Click to collapse
1. if you have warranty and not used odin, better take it to the samsung service center.
or
2. try to get a full charge battery from your friend and finish your job in dwnl mode using odin
or
3. try usb jig method to reset and start your mobile in recovery/dwnl mode.. you can search the forum on this and there are lots of posts reg this.
explains the randomness
If the connector moves its presumably broken connection with motherboard. Wonder if a teeny drop of superglue.....
Its odd how its become a feature after ICS but I suppose if its an age/ wear and tear thing that works too. Mine is drvibg me nuts too
Not solved with Stock ROM
Im also having the same problem . Not able to fix it. But if u want to connect to PC , just connect ur phone to PC and restart the phone. Then the drivers will installed and it will detected . Now u can flash it using ODIN . I tried updaing through the Kies with latest version of ICS patch , now the warning mesasge is not coming , but the battery icon blinks every second and if i check the status it shows NOT CHARGING instead of DISCHARGING
I know, I know, another bootloop thread. I've been reading dozens of them and I can't find my problem, please forgive me.
My wife's phone was stolen, and so we bought a used one from a stranger after seeing a listing on a local sales site (gumtree). Bad call - they demo'd it for us, but we didn't power it off and on before buying. After parting with cash, we find the phone won't boot unless it's plugged in to AC power (and not USB). All it does is loop grey/green battery logos over and over. Sometimes vibrating, sometimes not, but it would never break the loop, except to enter download mode, unless I connected it to AC power.
If I did boot it, I couldn't do some stuff, like enable USB debugging - it flat out wouldn't allow me to check that box. So I checked the kernel, and it seemed to have a weird kernel installed, so I thought it was time to just re-flash with the official firmware.
Well, first I wanted to try SlimROM, but I couldn't get to CWM Recovery (which was already installed) reliably, and on the rare instance where I could get it to come up, I couldn't navigate to extSD where the slim files were, nor mount USB storage (the PC wouldn't recognize it).
So I decided to try and re-flash to stock, using ODIN and the official samsung FW that worked well on my own GS2. This worked, after a fashion - I could get it to boot if I applied AC power, but things were badly broken. It'd reboot a minute or two after the setup began, and so I was forced to suspect either hardware failure or something that survived a complete wipe and flash.
So I thought kernel. The only one I had lying around that I knew worked was an old jeboo kernel. I flashed it with ODIN, and presto - it worked! The thing booted and stayed stable.
But I still have that accursed battery loop when the phone's off, the battery needs to be yanked to keep it actually powered down. And there are other bugs, like the screen comes on after you turn it off with the power button. Just once, but now it can't be powered down and ignored - you turn the screen off and wait to see if it comes back on and do it again.
And it's confused about charging - this morning it reported the AC adaptor was a USB charger, and this evening it thinks both USB and the AC adaptor are both AC (in the battery info settings screen).
And the only way to get it to boot reliably now is to remove the battery and plug it back in, at which point it boots as normal.
So, after all that long winded four-hours-of-tears-and-anger story, my question is this: What's the battery boot loop all about? Why does the screen flicker constantly when it's charging via AC? Why does it take -twenty seconds- to recognize it has been plugged in to power?
I can't install CWM, it won't enter recovery or boot successfully (no loop, just hangs on the yellow triangle screen). Before I start randomly applying new ROMs via odin, I'd like to find out more about my problem.
Please, can anyone shed light on this? I thought I knew what I was doing but I'm coming up empty here.
Sounds like the USB board/port (tho it might be worse than that; this is what I'd replace first). Relatively cheap/easy to replace; but you do need to check which board is currently in the phone & ensure you get the exact same as a replacement - there's 4 different boards, get the wrong one & you won't fix the problem/waste time & money.
Search for similar threads, there have been detailed threads in Q&A over the past few mths, those threads should have the info you need.
There's also a chance it might be as simple as the battery on the fritz, if you're able, try another one.
But definitely sounds like the USB board (hopefully for you) to me
Thanks for the suggestion. Certainly the flickering while charging issue and the delay to recognize the charger being plugged in point towards a USB board issue, but what I can't figure is the reluctance of the unit to boot without changing the kernel. Wouldn't the stock ROM via ODIN have included the stock kernel? Why does CWM cause the unit to lock up during boot?
Last night the thing stopped flickering on AC and recognized the charger cable instantly - is this a self-calibrating feature? (My research of a thousand similar threads seems to suggest a lot of battery issues correct themselves). For the record, the phone did come with a second 3rd-party battery, but neither it nor my own original GS2 battery make any difference.
So... Yeah, I'm still not sure if this is a hardware problem, software problem, or both.
Also last night I followed a suggestion from another thread and loaded up touchwiz, changed the screen timeout and switched back to apex launcher, and the screen started shutting off as desired. This morning it doesn't work anymore, and the phone is frequently found with the screen turned on. =/
Ok so by flashing full stock rom that practically eliminates the software side of things. Now do what mistahbungle said. My money is also on the usb board. I had to replace mine recently. Click the link on my signature, from there you can get onto a guide by keithross39 on how to DIY if you choose.
Sent from a galaxy far, far away
'practically eliminates' indeed. I still can't work out why I had to flash a new kernel to get it to boot. =/
NFGman said:
'practically eliminates' indeed. I still can't work out why I had to flash a new kernel to get it to boot. =/
Click to expand...
Click to collapse
Do you want help, or do you want to continue doing what you think will fix the problem? If you're having the same issues on full stock, it indicates hardware issue. The software won't work unless the hardware is functioning correctly. Let me think, what did MistahBungle say was the problem? Oh that's right. The USB board. Hardware.
Oh, sorry, I thought we were having a conversation. Should I not talk until I get the replacement part?
I'm not disagreeing, I'm fully prepared to accept the USB board is part or all of the problem, but I still wonder why etc etc.
OK....so....firstly, flashing a standard single file firmware won't fully wipe the previous software.....all it does is overwrite what it needs to (leaving who knows what untouched). The easiest way to regain a 'clean slate' is to flash a 3 part test firmware which DOES complete a full wipe during the flash..... @Hopper8 s guide provides a link to this test firmware and full instructions as to how to install it.
Secondly.....hardware faults can/do cause unexpected operational issues......some of the issues you describe were appearing on my wife's S2 before I replaced the USB board on her phone (they disappeared afterwards). As @Hopper8 has mentioned, his guide includes a link to my guide concerning the replacement of this part. I personally would hold off doing any more Odin flashes until you have replaced the board......if the USB port fails during a flash (because of a faulty board) you'll end up in a 'whole world of hurt' that will be infinitely worse than it is now.......
Sent from my GT-I9100 using xda app-developers app
Thanks to both of you for the responses. I've taken the phone to a repair shop and they swapped out the USB board to no avail. =/
Given what you've already spent on it (cost of phone + replace USB board), if I were in your situaton, I'd be cutting my losses & put it down to experience rather than replacing the motherboard (with a 2nd hand board from a 'donor' phone), whilst that's nowhere near as expensive as paying a service centre to put a new board in, it's still likely to cost you >AUD$100. If you can get one for a lot cheaper than that, maybe it would be worthwhile.
NFGman said:
Thanks to both of you for the responses. I've taken the phone to a repair shop and they swapped out the USB board to no avail. =/
Click to expand...
Click to collapse
Or...as first measurement, you clean the pins briefly and bend the holder slightly back to the center.
Tapatalked from my Galaxy SII
By 'holder' do you mean the USB port, or the connection inside the phone between the USB board and main board?
It's not a physical problem, at least in the USB port... I mean, we put a new one in it and nothing changed.
NFGman said:
By 'holder' do you mean the USB port, or the connection inside the phone between the USB board and main board?
It's not a physical problem, at least in the USB port... I mean, we put a new one in it and nothing changed.
Click to expand...
Click to collapse
Ah the usb board had already been replaced? Okay then forget about my proposal, sorry.
Tapatalked from my Galaxy SII
So the next step is either a motheboard replacement or the bin.
I realise this isn't what you want to hear, but think logically about it...You bought a 2nd hand phone from someone you don't know/had no idea what they'd put the phone through before you bought it, it crapped itself shortly after, giving no indications whatsoever the problems are firmware/software related, and showing a number of symptoms which indicate something major is wrong hardware-wise.
You tried the cheap/obvious & that didn't work, one way or another you need to bite the bullet (both options involve you spending a not insignificant amount of money in all likelihood, unless you can score a donor phone cheap).
MistahBungle said:
So the next step is either a motheboard replacement or the bin.
Click to expand...
Click to collapse
Way ahead of you. Ordered a new (NEW this time) phone. Will be selling the S2 to the next guy, along with the caveat "Sometimes the screen comes on." Will lose a few bucks, but it'll go into the old logbook of lessons well and truly learned. ^_^
Thanks for your help.
Hey Guys, ive scoured google for 2 days now trying to find a way to fix my phone.
two days ago i was doing some work and i left my phone on the table, and later i found out that the battery was low and it had shut off. But when i looked at it, it was just flashing the "samsung galaxy s2 gt-i9100" text logo. (and not the animation circle logo.)
I tried turning it off, didnt work so i thought it had frozen which happens, so i took out the battery and put it back in again.
Then i tried to plug it into my recharger, and it was showing a grey battery icon and was frozen on that screen always, the screen doesnt turn off, the battery icon isn't showing that its charging. doesnt change, just shows the same empty battery grey icon with the refresh circle-arrow in the middle.
I tried taking the battery out leaving it out for 5 minutes, draining the battery from the phone by holding the power button for 10 seconds, then trying to charge the phone. Same issue, only showing the grey battery icon when trying to charge and it never changes or goes away.
SO i tried to boot up the phone, but it wont go past the samsung text logo.
I tried entering recovery, but it just freezes on the samsung text logo.
I can enter Odin download mode, and ive tried installing several different both stock, original and CMW roms, and nothing changes. (except if i use gingerbread, then the grey battery icon just keeps flashing off and on in 5 second intervals when plugged into the charger.)
Ive tried taking the battery out for 8 hours and try booting it, no change.
Ive tried changing the battery, no change (think it has low bat as well maybe).
Ive tried leaving it plugged in overnight, but that only drained whatever power i had left over in one of the batteries.
Ive tried some of the siyah and doriman kernels, and they add a loading bar which gets full on the samsung text screen,
but then freezes after that.
Im losing my mind here, ive tried almost everything i can think of. And would really appreciate any help on this.
UPDATE
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ok so to keep this post updated for people experiencing the same issues.
IT seems there is a hardware failure in progress.
BUT i managed to get a temporary fix, it seems that by having the ear plugs connected into the earphone jack in the phone, the phone becomes somewhat usable. I was able to get into recovery, and able to flash a new stock, and its up and running, but as i said this is only a temporary solution as the real issue is that the phone is not conducting the electricity in a proper way that allowed me to recharge my batteries until i had added the earphones...
The phone becomes unusable for me when i remove the earphones again, as i believe its failing to conduct the electricity from the battery properly through the motherboard without something connected into the earphone jack..
SO for people having issues with their phones, it might be a possible way to get your phone temporarily operational again.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Search for Hopper8's 'Odin troubleshooting' thread, download the 3 part stock firmware linked in the thread, flash it with Odin (only if you absolutely have an I9100/I9100T though).
Edit - Doesn't sound promising though, cross your fingers doing that works.
yeah i tried hoppers guide, didnt help me.
Still stuck on the samsung screen.
Whats wierd is, if ive got the phone on charging, it wont boot to the samsung screen even, it just turns itself off
and returns to the grey battery icon again.
Hang on....Did you try flashing the 3 part firmware like I mentioned ? If you haven't, do it. If you have, it's a service centre/local mobile repair shop job.
MistahBungle said:
Hang on....Did you try flashing the 3 part firmware like I mentioned ? If you haven't, do it. If you have, it's a service centre/local mobile repair shop job.
Click to expand...
Click to collapse
Yeah, tried 3 part, even another packages with pit files bootloader and repartitioning from another guide.
still no change, still freezes at samsung text screen.
I dont want to take it to a service center, as there is none around here as far as i know. Norway.
If i can just get it into recovery mode i can prob fix it, but i cant fracking enter recovery. Its driving me insane.
Given what you've tried, no chance of fixing it yourself by the usual methods.
Either take it to a local mobile repair shop & ask them to source a 2nd hand motherboard for you & put it in, or you source one (from a 'donor' phone; a phone with a broken screen that is otherwise OK for example, search online) & either replace it yourself or pay the local mobile repair shop to do it if you're not confident enough.
have you ever flashed a rom on that before..... or is this a stock ROM phone we are talking about???
if it was a stock ROM phone....then did it receive updates over carrier network and started to install itself???
if yes then you should have not stopped it...... i have some problem with phone 3 days ago.... i downloaded latest XWMS1 released for nordic region....... phone is fixed and i am back to neatrom 5.3.1
i suggest you download XWMS1 ...and try flashing it via Odin..... might start......
keep fingers crossed
Roshan707 said:
have you ever flashed a rom on that before..... or is this a stock ROM phone we are talking about???
if it was a stock ROM phone....then did it receive updates over carrier network and started to install itself???
if yes then you should have not stopped it...... i have some problem with phone 3 days ago.... i downloaded latest XWMS1 released for nordic region....... phone is fixed and i am back to neatrom 5.3.1
i suggest you download XWMS1 ...and try flashing it via Odin..... might start......
keep fingers crossed
Click to expand...
Click to collapse
It wasn't any update or anything, it was related to the battery i think as the batt was low.
And instead of recharging the battery, it went into bootloop and started draining the battery more when it was plugged into the charger.
ive downloaded xwms1, still stuck in bootloop.
Ive even opened it up to see if it was a hardware issue, i see no flaws, all buttons work and nothing is stuck.
the phone just keeps going to the samsung logo, and wont go into recovery mode.
It can easily go into download mode, but recovery mode is just not happening.
at this point i just ordered the Xperia Z1 instead, but i still want to fix this phone and give it to my dad or something.
desidarko said:
Hey Guys, ive scoured google for 2 days now trying to find a way to fix my phone.
two days ago i was doing some work and i left my phone on the table, and later i found out that the battery was low and it had shut off. But when i looked at it, it was just flashing the "samsung galaxy s2 gt-i9100" text logo. (and not the animation circle logo.)
I tried turning it off, didnt work so i thought it had frozen which happens, so i took out the battery and put it back in again.
Then i tried to plug it into my recharger, and it was showing a grey battery icon and was frozen on that screen always, the screen doesnt turn off, the battery icon isn't showing that its charging. doesnt change, just shows the same empty battery grey icon with the refresh circle-arrow in the middle.
I tried taking the battery out leaving it out for 5 minutes, draining the battery from the phone by holding the power button for 10 seconds, then trying to charge the phone. Same issue, only showing the grey battery icon when trying to charge and it never changes or goes away.
SO i tried to boot up the phone, but it wont go past the samsung text logo.
I tried entering recovery, but it just freezes on the samsung text logo.
I can enter Odin download mode, and ive tried installing several different both stock, original and CMW roms, and nothing changes. (except if i use gingerbread, then the grey battery icon just keeps flashing off and on in 5 second intervals when plugged into the charger.)
Ive tried taking the battery out for 8 hours and try booting it, no change.
Ive tried changing the battery, no change (think it has low bat as well maybe).
Ive tried leaving it plugged in overnight, but that only drained whatever power i had left over in one of the batteries.
Ive tried some of the siyah and doriman kernels, and they add a loading bar which gets full on the samsung text screen,
but then freezes after that.
Im losing my mind here, ive tried almost everything i can think of. And would really appreciate any help on this.
Click to expand...
Click to collapse
errrrm - just a thought (and it's a real long shot) I had some strange battery drain (bootloop) issues with a brand new i9100 and it turned out that the micro sd card I was using was corrupt, took it out and it worked. Might be worth a try but like I said its a long shot. If that does not work I agree with mistahbungle and looks like you wil need to replace the mb.
Jimsilver73 said:
errrrm - just a thought (and it's a real long shot) I had some strange battery drain (bootloop) issues with a brand new i9100 and it turned out that the micro sd card I was using was corrupt, took it out and it worked. Might be worth a try but like I said its a long shot. If that does not work I agree with mistahbungle and looks like you wil need to replace the mb.
Click to expand...
Click to collapse
Yeah ive already taken out the micro sd card and sim card, didnt change anything.
Just so weird the phone is less than 2 years old. Sucks that its already llike this.
desidarko said:
Yeah ive already taken out the micro sd card and sim card, didnt change anything.
Just so weird the phone is less than 2 years old. Sucks that its already llike this.
Click to expand...
Click to collapse
I've went through this on my Hercules, T-Mobile S2. I had Android tweaker pro, removed all of the tweaks, and rebooted. It took me quite a while but I was able to get into recovery by the normal button mashing.
DO NOT HAVE THE PHONE PLUGGED INTO THE CHARGER.
PRESS THE VOLUME BUTTONS THEN THE POWER BUTTON WHILE STILL HOLDING THE VOLUME BUTTONS.
AS SOON AS YOU FEEL THE FIRST VIBRATION, LET GO OF ONLY THE POWER BUTTON!
CONTINUE TO HOLD THE VOLUME BUTTONS UNTIL YOUR RECOVERY LOADS.
THAT IS WHAT HAS WORKED FOR ME.
Sent from my Skinny Hercules
Ok so to keep this post updated for people experiencing the same issues.
IT seems there is a hardware failure in progress.
BUT i managed to get a temporary fix, it seems that by having the ear plugs connected into the earphone jack in the phone, the phone becomes somewhat usable. I was able to get into recovery, and able to flash a new stock, and its up and running, but as i said this is only a temporary solution as the real issue is that the phone is not conducting the electricity in a proper way that allowed me to recharge my batteries until i had added the earphones...
The phone becomes unusable for me when i remove the earphones again, as i believe its failing to conduct the electricity from the battery properly through the motherboard without something connected into the earphone jack..
SO for people having issues with their phones, it might be a possible way to get your phone temporarily operational again.
Please Help !!
i kinda cloned my ROM , it happened by mistake while trying to flash my kernel , now that my phone is stuck in samsung start up logo , . tried to reboot still the same result. . . :crying:
No recovery ? If that's the case, stock rom from Samfirmware, flash with Odin to get a 'clean slate' (How ? Thread stickied near top of Q&A has instructions) & re-try whatever it was you wanted to do. If you do have recovery, try a factory reset in the first instance, if that doesn't work or if you have recovery but can't do one for whatever reason, proceed with the stock flash via Odin.
Thanks
thanks a lot mate , my fone back in action. successfully flashed, now running on JB 4.3.1 on Paranoidandroid 3.99-RC2 , so far so good .:victory:
being a newbei in this field hoping for all the support
EDIT : any suggestion how to remove warning symbol (yellow triangle) while booting .
Possibly triangle away.Search to get the free version.
desidarko said:
Ok so to keep this post updated for people experiencing the same issues.
IT seems there is a hardware failure in progress.
BUT i managed to get a temporary fix, it seems that by having the ear plugs connected into the earphone jack in the phone, the phone becomes somewhat usable. I was able to get into recovery, and able to flash a new stock, and its up and running, but as i said this is only a temporary solution as the real issue is that the phone is not conducting the electricity in a proper way that allowed me to recharge my batteries until i had added the earphones...
The phone becomes unusable for me when i remove the earphones again, as i believe its failing to conduct the electricity from the battery properly through the motherboard without something connected into the earphone jack..
SO for people having issues with their phones, it might be a possible way to get your phone temporarily operational again.
Click to expand...
Click to collapse
Okay so I have managed to get it to this point after day's of grief, now please tell me I don't have to walk around with the earplugs in for ever !
RustyNail99 said:
Okay so I have managed to get it to this point after day's of grief, now please tell me I don't have to walk around with the earplugs in for ever !
Click to expand...
Click to collapse
A friend of mine had am Android phone that had a similar problem. It always showed the headphones on the status bar and Could not be heard. If you will take your phone apart then you can look for bridges in the solder points. These happen from poor construction and over heating. Fix the bridges and you should be good to go.
Sent from my Skinny Hercules
fathertomany said:
A friend of mine had am Android phone that had a similar problem. It always showed the headphones on the status bar and Could not be heard. If you will take your phone apart then you can look for bridges in the solder points. These happen from poor construction and over heating. Fix the bridges and you should be good to go.
Sent from my Skinny Hercules
Click to expand...
Click to collapse
I did take it apart and had a quick look, all seems ok. However I was not ready to junk the phone so I improvised a little, its not pretty but it works.
I had an old headphone jack which I cut down so as it would just fit into the jack point, installed Soundabout Pro app which forces the calls to come out the earpiece and not headphones voila it works. In the end it cost me a lot of time surfing countless forums, anger management control and some joy at getting it to work. Still without the help people give on this and other forums it would be a useless phone :fingers-crossed:
sweetben747 said:
thanks a lot mate , my fone back in action. successfully flashed, now running on JB 4.3.1 on Paranoidandroid 3.99-RC2 , so far so good .:victory:
being a newbei in this field hoping for all the support
EDIT : any suggestion how to remove warning symbol (yellow triangle) while booting .
Click to expand...
Click to collapse
i was also searching for the same...... since triangle did not hurt but i wanted to know if i could get rid of it......
thanks to our wonderful Dev name Phliz i could do it... i had to reflash to stock for it ofcourse but then whole effort was worthwhile .....
http://forum.xda-developers.com/showthread.php?t=1877270
this is the link.... please go through... and best of luck to remove the triangle.....
My phone wouldn't power on so I got it repaired at a phone repairs shop. The guy there thought there was a software error because he saw the error triangle on bootup. He was mucking around with it in download mode when I got there, I said not to worry about it, paid for the repairs and left.
The phone will not boot, and will not go into recovery or download modes with the respective key combinations
UNLESS
I have it plugged into a power source, in which case I can enter download/recovery mode, but when I try to boot the phone I just get the empty battery picture with the loading circle appearing periodically.
--- Possible solution: bad battery
I have flashed CWM onto the phone using odin in download mode and have flashed .zip roms that were previously working before this debacle, but again the phone won't boot onto the newly installed rom.
I have tried flashing the correct stock rom using odin but the phone won't boot this way either.
When I take the battery out and connect the phone to a power source it is non-responsive.
Apart from a batter problem (which I will be able to test tomorrow), what could be the cause of this problem, and how might I be able to fix it?
Sounds like a JTAG (but don't get your hopes up) or a motherboard replacement job (more likely) to me. If the phone won't boot at all/shows no signs of life, something is majorly wrong. As to what that is, nobody here could tell you that with certainty because we don't have the phone in front of us, but if it's not booting at all either the NAND is buggered or something else on the MB has crapped itself.
Cross your fingers it's just a simple battery issue, but it doesn't sound like it.
MistahBungle said:
If the phone won't boot at all/shows no signs of life
Click to expand...
Click to collapse
What does being able to access recovery mode/download mode contribute to this? The phone works to a degree, it seems, it just won't boot to an OS.
How might I go about troubleshooting the hardware?
(Might as well use this as a learning experience)
Right. Sorry. Just re-read your OP. Still sounds like the NAND is stuffed, which explains why you've tried flashing flashing stock/CWM & phone still won't boot normally. One thing you could try is search for Hopper8's 'Odin troubleshooting' thread, and flash the 3 part firmware linked in that thread. If the phone still won't boot normally after that, it's pretty much a certainty that you'll need to replace the MB at least, which leads to the next paragraph...
Also, if you find the 'booting when plugged into charger but not with battery' thing is still happening even with a new battery, that suggests whatever circuitry is responsible for taking zzz's from the battery & powering the device is (also) faulty/damaged. You could also try the obvious & clean the battery contacts with some isopropyl alcohol. The most common charging/power type problems we see here is the USB board/port dying. But if the phone is slightly functional whilst on charger, it probably isn't that, still might be worth replacing though given how quick/cheap/easy it is to do. There could be a short/whatever causing at least some of the problems, and it wouldn't be the first time a faulty USB board has caused that/manifested itself in less obvious ways than what we normally see (I.E causing the problems you're seeing rather than causing intermittent charging problems or phone rebooting randomly on its own or whatever).
In that case, try the service manuals for the device; these have been posted here before & can also be found with a Google search. They have detailed schematics/parts lists/walk throughs of the most common repairs w/pics, and might help if you want to have a go at fixing it yourself.
Thanks for the response.
I'm in the process of downloading the three part firmware to test later in the night.
Providing that fails, I'll look into part supplies and start researching how I can, if at all, repair this myself.
On the topic of faulty USB boards- I had my phone serviced a few months ago for just that, and it worked fine, but in the weeks leading up to this event my phone HAD been rebooting itself semi-regularly, although I put this down to a software issue rather than a hardware issue. I'll get my hands on the service manual for the I9100 and start reading up.
In the meantime I can just get a cheap burner Nokia that won't play up on me for the next 20 years.
Interesting. In that case, given the other alternatives are more expensive (assuming the 3 part firmware & new battery doesn't fix things), it may just be a case of another dodgy USB board & you might want to start there.
If you can't find the manuals anywhere, let me know & I'll see if I can dig them up from an external drive I have stashed away somewhere (don't have it handy now, but will dig it up tomorrow for you if necessary).
Yep, unlike current technology, old phones like that just seem to work no matter what you throw at them
The three part firmware flashing has moved things along slightly- after it finished the stock SGS2 boot screen appeared for a second or so and while leaving it on the charger it will cycle between showing the grey loading battery and an android with a loading bar underneath, which is progress from before. It is still unresponsive when disconnected from the power- I have procured the service manual and will look into disassembly/diagnostics when I have some small enough tools. I'll still try using a different battery when I can, but it probably isn't the issue.
Clean the battery contacts hard with a pin
Sent from my GT-I9100 using xda premium