Related
When I try to reinstall the firmware it will not work. I get a message update failed: (1). This is done in the recovery section. I have put the latest firmware in, but nothing happens other then the error message. When I turn on the Archos it just goes straight to the Archos A70S Recovery screen. I have totally reformatted the device several times. Any thoughts on this board? Thanks.
Aaron
Try to format the device and then install the firmware, also, make sure to have the right firmware so the archos stock .aos file and not the SDE firmware .aos file
have you tried redownloading the archos firmware again? maybe the download got corrupted?
Also try running the repair tools under recovery: specifically Check Disk?
do you have a (1) at the end of the aos file? "sdqsqdfkqsdomij(1).aos" like Firefox do, i had the same error like that
Thanks...but I think I have tried it all...no luck
Try using a different browser, like IE to download it.
I've got the same thing going on. Was trying to re-partition the app space and something didn't work for the 4th time. So I removed Android and the SDE and now I can't get it to boot. My problem is that I was running windows, not sure what you were using, and I changed the recovery location's format. So every time I go to load the file the archos will format the partition then windows says it will not read and formats the partition... I move the file and try to start the reload only to fail.
I'm going to run ADB hopefully tomorrow. I hardly know what I'm doing, but don't really care if I break it! Just playing around but if anyone has any ideas let me know!
If you removed sde and android, there is nothing to boot from.
You then have to go into the recovery, format the device from there and then restore the orginal Android by transfering the aos file from arcos.
Yeah, I might have done that 10 times. That is when the archos reformats itself to something and then windows can't read the drive.
After you have transfered the AOS File to the device and it installs the Archos Android
it reformats the device to something?
I think that the archos is formatting to ext3 but windows can't read it, so windows then formats to whatever and I move the file, then hit ok on archos and you get failed message.
I know that AOS files work because I have already used them once.
If any of you guys give up on trying to get life into your bricked gen8 devices, then shoot me a message... I might be interested in buying the device from you.
Have you tried tried to fully charge it before installing? I had that same problem and it got fixed by fully charging the device first.
Full charge and plugged in as we speak.
You now have 133 posts on xda and still are not able to post a complete detailed description of what you are doing and what is happening?
How should we help?
My suggestion if you get an Error, tell us what error exactly, as my crystal ball is on repair atm.
Ha! 393 posts and your only kind of a ****? Thanks!
All kidding aside It's not easy to describe whats going on, and I wasn't trying to hijack this thread but I think the original poster is way gone. I was only trying to say I had the same problem and was going to try a few things to get it working again, but this was only yesterday and I have not had luck. I never really even asked for help but appreciate everyones input.
So... Let me start again!
Archos 101.
Long ago I had Urik Droid 1.0 installed but it had since been removed. Before I messed everything up i had the latest Archos update and rooted. I was trying to create a large partition for apps and had just edited the init.rc and rebooted. Somewhere here I messed up! Boot loops start and I'm into recovery.
Recovery shows everything normal, but I'm unable to update archos via AOS file. So I totally reformat and remove SDE in an attempt to just start fresh. This is not the case and I figured it wouldn't be.
As I described before, using windows, in archos recovery this is what is displayed.
Archos A101IT Recovery
Would you like to recover system?
NO
REBOOT
UPDATE FIRMWARE
REPAIR SYSTEM
FORMAT SYSTEM
If you select updated firmware the archos will reformat to ext3. It then says USB connection: Press OK to disconnect. Windows then says that it is unable to use the disk and asks to re-format. I did, because I don't think I can do anything else, moved the AOS file over and hit ok. Update failed (1).
So today I installed linux in an attempt to move ext3 to ext3. I did get the file transfered and my archos even said plug into dc power. I did and waited... Update Failed (206). Not sure what this one is!
And that's really all I know. I can't even get the last thing I described to come up again. But I have all week on vacation.
And lastly I would like to thank you for the help
And I just got the AOS to install! Formated repair to Vfat, used repair option and moved AOS into archos. For whatever reason this time it worked. Rebooted and android just started up. Don't know if everything works yet but we will see!
Funny, you do the mistake and call others names.
fzelle said:
You now have 133 posts on xda and still are not able to post a complete detailed description of what you are doing and what is happening?
How should we help?
My suggestion if you get an Error, tell us what error exactly, as my crystal ball is on repair atm.
Click to expand...
Click to collapse
Let me make this clear...
I was kidding. Take a deep breath, relax and please try to help someone else if that is what you are on here to do.
I'm pretty sure what you said to me was worst then my little joke. It was hardly clever and I'm ok with it as it did make me laugh a little.
I didn't ask for your help.
I didn't need your help
You didn't help.
And I'm ok with it even if you are not.
I'm going fishing now. Good day everyone.
No, it was exactly what you needed, as before my message you didn't tell us what was happening on your side.
Please read what you have posted before and check yourself if you would be able to get any sence from that.
It is funny how some people handle kritik.
I've got the Telstra RHOD110 and I've tried to install every Android build since about the first stable Froyo release. Every single one of them hangs during the Linux boot sequence.
It seems to be memory related, but past that I've got no clue - I'm an IT professional, but I'm in operations, not development so I'm a little out of my depth with this stuff.
I have NOT done HardSPL yet, but I was under the impression this wasn't necessary for the SD card method (which I wanted to test out before potentially bricking a ~$1000 phone). In theory it's just the standard Telstra WinMo 6.5 ROM...
It's getting a bit frustrating after years of trying this and seeing everyone else talking about how easy it is. I'm using F22's rootfs and TotalCommander isn't showing up any *.csv files in the \windows directory, so I can't even try the GBX0C (2.3.7) test build. Anyone know why my phone seems to be different?
Hi Nukkels lets focus on getting GBX0C running since
Nukkels said:
I have NOT done HardSPL yet,
Click to expand...
Click to collapse
First things first: Format the MicroSD you plan to use using the HP USB Disk Storage Format Tool. Just use google to find it. I use version 2.1.8. Perform a FULL format, FAT32.
Now download the package from here: http://files.xdandroid.com/GBX0C_Full_Bundle_2012.04.24.zip and extract all of the files to the root of your SD card
Nukkels said:
I've got the Telstra RHOD110
Click to expand...
Click to collapse
This device is identical to the RHOD100_UK so pull the startup.txt out of the STARTUPS\RHOD\RHOD100\ and place it on the root of your storage card.
Nukkels said:
I'm using F22's rootfs
Click to expand...
Click to collapse
I think I understand why you are trying to use that rootfs since it has some stuff tailor made for Rhod110/Telstra but I don't think it is necessary. Just leave the existing rootfs.img from the GBX0C package, it should work for you.
Nukkels said:
TotalCommander isn't showing up any *.csv files in the \windows directory
Click to expand...
Click to collapse
I haven't used TotalCommander for a while, but it seems to me that there is an option like "Hide Files in ROM" or "Show Hidden Files" or something like that which is probably preventing you from seeing the .csv's in /Windows/. So find that option and find those files and copy them to the root of your storage card.
If you can't find them I think that GBX0C should still boot as I have booted without any .csv's, there was just no sound in the build. But at least you can see that it is working. In case you absolutely cannot find them, here are my .csv's from rhod100uk: View attachment RHOD100_CSV.zip, unzip to your storage card, which hopefully will get you going.
Okay, now all you need is a touch screen calibration file. If you do not have one here is mine:View attachment ts-calibration.zip
Unzip it to the storage card.
Now you have everything in place on the card, please at this point do not try to edit the startup.txt or anything in /conf/. Lets just get this baby working.
Before you run anything I would set WM to airplane mode, set your backlight control to any level but auto (ie low), and make sure that you are not overclocking your processor in WM.
Now run HaRET.exe from the root of the storage card and cross your fingers mate!
Be patient, first boot can take ~10 minutes sometimes.
EDIT: Also there is a fairly good chance that your thread will get moved to the Android section... if it does and you aren't able to post in it anymore you can PM me.
I just wrote up a huge post and lost it all :crying:
Basically I followed your sintructions step by step and it worked!
I'd never done a FULL format before - that takes hours! I'm guessing this might have been the main issue.
I'll play around over the next few days with F22s rootfs and rhod110 startup parameter, Airplane mode turned on, etc to see if any of that had an impact. I never thought to set backlight to manual or use Airplane mode.
Hopefully I can help find the crucial step I missed, so it can be included in the installation instructions (or at the very least someone might stumble on this thread).
Anyway thanks a tonne for your help, it got me up and running!:good:
Thread moved to the appropriate section.
I genuinely hope you didn't pay ~$1000 for this phone... wow.
Caldair said:
Hi Nukkels lets focus on getting GBX0C running since
First things first: Format the MicroSD you plan to use using the HP USB Disk Storage Format Tool. Just use google to find it. I use version 2.1.8. Perform a FULL format, FAT32.
Now download the package from here: http://files.xdandroid.com/GBX0C_Full_Bundle_2012.04.24.zip and extract all of the files to the root of your SD card
This device is identical to the RHOD100_UK so pull the startup.txt out of the STARTUPS\RHOD\RHOD100\ and place it on the root of your storage card.
I think I understand why you are trying to use that rootfs since it has some stuff tailor made for Rhod110/Telstra but I don't think it is necessary. Just leave the existing rootfs.img from the GBX0C package, it should work for you.
I haven't used TotalCommander for a while, but it seems to me that there is an option like "Hide Files in ROM" or "Show Hidden Files" or something like that which is probably preventing you from seeing the .csv's in /Windows/. So find that option and find those files and copy them to the root of your storage card.
If you can't find them I think that GBX0C should still boot as I have booted without any .csv's, there was just no sound in the build. But at least you can see that it is working. In case you absolutely cannot find them, here are my .csv's from rhod100uk: View attachment 1184798, unzip to your storage card, which hopefully will get you going.
Okay, now all you need is a touch screen calibration file. If you do not have one here is mine:View attachment 1184808
Unzip it to the storage card.
Now you have everything in place on the card, please at this point do not try to edit the startup.txt or anything in /conf/. Lets just get this baby working.
Before you run anything I would set WM to airplane mode, set your backlight control to any level but auto (ie low), and make sure that you are not overclocking your processor in WM.
Now run HaRET.exe from the root of the storage card and cross your fingers mate!
Be patient, first boot can take ~10 minutes sometimes.
EDIT: Also there is a fairly good chance that your thread will get moved to the Android section... if it does and you aren't able to post in it anymore you can PM me.
Click to expand...
Click to collapse
I tired this on my TILT 2 it wouldnt work...
tru209 said:
I tired this on my TILT 2 it wouldnt work...
Click to expand...
Click to collapse
So... what's broken with it? Where does it stop?
Edit - basically, you've gotta give us more to go on. We can't help you with "wouldn't work" - it's simply not enough info. Provide as much as you can - what did you try, what happens when it boots, did anything semi-work, etc etc. Details!
tru209 said:
I tired this on my TILT 2 it wouldnt work...
Click to expand...
Click to collapse
Did you bite your tounge just right while dancing backwards to the wizard of OZ soundtrack? That always does it for me when it 'wouldnt work'.
My experience was that the full format using the HP tool is a crucial step. I did a full format using other tools but I had no joy until I did it with the HP tool.
Need some help with the "AdamOutlerUbuntuTotalReFlash" method. I am missing or overlooking something but, can't figure out what. I have installed the Ubuntu 12.0.4 on an older laptop in an effort to 1) learn but 2) mostly to restore my 16GB NT. Currently the Nook will only boot to CWM. I have tried a few different methods and images but, can't seem to get anything to load. Do I need to repartition and can anyony help with that, I am at apoint wher maybe I have tried to learn or do to many new things at once and am frustrated and confused. I don"t believ all is lost but could sure use a little more help/direction. I have followed all of Adam Outler's steps but, seem to run into trouble with having success writing the image to the SD card.
Is this what you are trying?: http://forum.xda-developers.com/showthread.php?t=1470910
If so, you do not need to have Ubuntu on your computer, nor know anything about it!
Scroll down to "WIndows" instructions and go!
1. Download - extract - rename Adams file
2. Open your disk imager and load the img you "created" in step 1.
3. Burn the image to your sd card
4. Boot into the card created in step 3 and follow the instructions below the picture. starting with "Theory of..."
thanks
asawi said:
Is this what you are trying?: http://forum.xda-developers.com/showthread.php?t=1470910
If so, you do not need to have Ubuntu on your computer, nor know anything about it!
Scroll down to "WIndows" instructions and go!
1. Download - extract - rename Adams file
2. Open your disk imager and load the img you "created" in step 1.
3. Burn the image to your sd card
4. Boot into the card created in step 3 and follow the instructions below the picture. starting with "Theory of..."
Click to expand...
Click to collapse
I would like to say thank you for the help and appreciate the support. I will give this a shot. this evening. a few Questions 1) when renaming the AdamOutlerUbuntuTotalReFlash.tar.gz file do i delete the .tar.gz extensions and replace them with the .img extension? or do i do i leave them so that the extension is now .tar.gz.img ? 2) when powering on the device do I power on with the power button on the NT or use the USB cable and let the device power itself on and does it matter if the device is plugged into the charger or the PC? Any specific instructions or specific utilities for formatting the SD Card?
Thanks Again!
I haven't done this recovery myself, so I really don't know anything about it. I would suggest you to read through that topic and see if the answers are there.
The instructions do say "extract" and THEN "rename"
Some general things I can say though:
When burning an image to sd card the card doesn't need to be formatted before doing it.
To get the NT to boot from sd crad is individual from device to device. Many say they only get theirs to do it by inserting charging cable to power adapter.
The three that have passed through my hands have booted to sd either by themselves when turning on power. If they haven't done so right away I hold down the "n" and that's it.
1_ton said:
Need some help with the "AdamOutlerUbuntuTotalReFlash" method. I am missing or overlooking something but, can't figure out what. I have installed the Ubuntu 12.0.4 on an older laptop in an effort to 1) learn but 2) mostly to restore my 16GB NT. Currently the Nook will only boot to CWM. I have tried a few different methods and images but, can't seem to get anything to load. Do I need to repartition and can anyony help with that, I am at apoint wher maybe I have tried to learn or do to many new things at once and am frustrated and confused. I don"t believ all is lost but could sure use a little more help/direction. I have followed all of Adam Outler's steps but, seem to run into trouble with having success writing the image to the SD card.
Click to expand...
Click to collapse
You should read this post before trying out any "unbricking" method and end up permanently bricking your NT.
asawi said:
I haven't done this recovery myself, so I really don't know anything about it. I would suggest you to read through that topic and see if the answers are there.
The instructions do say "extract" and THEN "rename"
Some general things I can say though:
When burning an image to sd card the card doesn't need to be formatted before doing it.
To get the NT to boot from sd crad is individual from device to device. Many say they only get theirs to do it by inserting charging cable to power adapter.
The three that have passed through my hands have booted to sd either by themselves when turning on power. If they haven't done so right away I hold down the "n" and that's it.
Click to expand...
Click to collapse
o.k. so i have downloaded the image, extracted it using winrar but, when i use the win32diskimager to write the image i can find the file but, the win 32 diskimager does not recognize the sd card or doesn't even let me open the little file foled at all for that matter as far as where to chose to write it to?
Hi all,
I tried Adams' method along with a few days worth of other methods. I've been unable to get past the writing MLO portion in Adams' method. Has anyone been able to get past this?
p.s. I'm a semi-n00b, this is my first tablet If it was a phone I'd be fine lol
Nvmd, I think I was using an old file, got it working now. Large thanks and respect to Adam!
Sent from my DROID RAZR using xda app-developers app
Here it is
http://forum.xda-developers.com/showthread.php?t=2179403
I hope someone can help me. I have a 16gb nook tablet that I rooted using the method described here http://liliputing.com/2012/03/how-to-dual-boot-cyanogenmod-7-nook-tablet-os-with-a-microsd-card.html over a year ago and I've never had an issue until last weekend. My daughter was playing a game and the nook started acting up. The touch screen became unresponsive and the screen started to flash. I let the Nook charge overnight and when I turned it on the next day the screen became stuck at the white Nook welcome screen. After 20 minutes I tried the holding down power and N button to see if I could get it to restart, but unfortunately that may have made it worse. Now my Nook won't start at all. I've read many many threads here on how to fix it, but I am not tech savvy in the slightest. The first thing I tried was Rays method http://raywaldo.com/2012/06/how-to-un-brick-a-nook-tablet-8gb-or-16gb/ but instead of getting the green checkmark I got the red X and the "nook is shutting down" message. I tried so many things that I cannot remember them all but I do know that one of the methods I tried I got this message.
E:Can’t mount / cache/recovery/command/
E:Can’t mount / cache/recovery/log/
E:Can’t open / cache/recovery/log/
E:Can’t mount / cache/recovery/last_log/
E:Can’t open / cache/recovery/last_log
After that I tried to use the method described here http://forum.xda-developers.com/showpost.php?p=24995518&postcount=1 and I did make the booktable cwm-sd and I went to lavero.burgos' thread to download the mmcblk files, but they weren't there.
Also I don't understand what adb is but I'm desperate, when I found the thread that explained it and tried to download the ADB + Fastboot + Drivers.zip that was in said thread (I'm sorry I can't remember which thread it was) the zip file didn't work.
I'm really sorry for posting yet another, "please help my nook is borked" thread but after all the reading I've done this past week the only thing I've become is very confused and frustrated. Thank you in advance to anyone who can help.
Notice on the link you posted
Ray Waldo; said:
If this procedure fails, try one of these:
Celtic has a possible solution on XDA here: http://forum.xda-developers.com/showthread.php?t=1513583
Succulent has more info on his Github page: https://github.com/succulent/acclaim_recovery_sdcard.
Click to expand...
Click to collapse
I can see how you got lost. There aren’t really any detailed instructions there.
I got the following zip from 2nd link
Flash the zip with CWM then try the bn_142_factory_recovery.zip SD card again and you should get a green checkmark this time.
udownwitopp said:
Notice on the link you posted
I can see how you got lost. There aren’t really any detailed instructions there.
I got the following zip from 2nd link
Flash the zip with CWM then try the bn_142_factory_recovery.zip SD card again and you should get a green checkmark this time.
Click to expand...
Click to collapse
Thank you for your reply. I will try this tonight and hopefully it will work.
Well I tried, and I hate asking but how exactly does someone add a zip file to an sd card after an image has been flashed to it? I've tried numerous times with sd cards of various sizes and I'm pretty sure I should have been able to do this with a 16gb card, but every time I try to drag and drop the flashstock zip over onto the card it says that there is no room available. Now I have been doing a lot of reading on here and I'm pretty sure I did not set the card up right, I did format it correctly with the sdformatter program, but I'm guessing I have to do something with the partitions on the card. I am not familiar with the programs because I've never had cause to use them before so I am not entirely sure how to do that. I tried following the directions found here http://forum.xda-developers.com/showpost.php?p=24995518&postcount=1 but I couldn't figure out how to enable boot, and lba flags. I realize that this has probably all been answered already, but again, there programs are so foreign to me that I'm not even sure what to look up first. Thank you again for any help that any one can give me.
evm22 said:
Well I tried, and I hate asking but how exactly does someone add a zip file to an sd card after an image has been flashed to it? I've tried numerous times with sd cards of various sizes and I'm pretty sure I should have been able to do this with a 16gb card, but every time I try to drag and drop the flashstock zip over onto the card it says that there is no room available. Now I have been doing a lot of reading on here and I'm pretty sure I did not set the card up right, I did format it correctly with the sdformatter program, but I'm guessing I have to do something with the partitions on the card. I am not familiar with the programs because I've never had cause to use them before so I am not entirely sure how to do that. I tried following the directions found here http://forum.xda-developers.com/showpost.php?p=24995518&postcount=1 but I couldn't figure out how to enable boot, and lba flags. I realize that this has probably all been answered already, but again, there programs are so foreign to me that I'm not even sure what to look up first. Thank you again for any help that any one can give me.
Click to expand...
Click to collapse
I'll try to explain the process for you. "The Red X" is a very common issue that people have with their devices. It's usually caused by digging into something that you don't fully understand. It's VERY important to understand the process of flashing custom ROMs because it could screw up your tablet, delete ROM partitions and such.
The first issue you need to attend to is "The Red X." First download the bn_142_factory_recovery.zip from the ray waldo site found here:
http://raywaldo.com/2012/06/how-to-un-brick-a-nook-tablet-8gb-or-16gb/
Unzip the zip file and you should have a repart.img. Use win32diskimager to write this to an SD card. Once it's done writing, put the SD card in your device and it should boot from SD card and flash stock B&N 1.4.2 to your nook (if you have problems booting from SD card plug in the USB to your computer).
If you still get "The Red X" during this process please use the following method:
http://forum.xda-developers.com/showthread.php?t=1513583
If you have further problems please post or PM me. Once you have the issue fixed I HIGHLY recommend using the SDC version. It's a lot easier than the Internal Version and will prevent mistakes from happening.
Thank you for responding. I retried the method described on Ray's site, but sadly it's still a no go. I have downloaded the parted binary and I know how to get it onto the sd card, but what I don't know is how to ADB into my device. I'm not even sure I understand what ADB is.
evm22 said:
Thank you for responding. I retried the method described on Ray's site, but sadly it's still a no go. I have downloaded the parted binary and I know how to get it onto the sd card, but what I don't know is how to ADB into my device. I'm not even sure I understand what ADB is.
Click to expand...
Click to collapse
I'm not extremely knowledgeable with the ADB tool, but it's setting up your computer so you can write commands into your command prompt that will execute actions on your device. The link for setting it up is here:
http://forum.xda-developers.com/showthread.php?t=1474956
Once you get it set up just follow the rest of the directions in the parted binary post.
datallboy said:
I'm not extremely knowledgeable with the ADB tool, but it's setting up your computer so you can write commands into your command prompt that will execute actions on your device. The link for setting it up is here:
http://forum.xda-developers.com/showthread.php?t=1474956
Once you get it set up just follow the rest of the directions in the parted binary post.
Click to expand...
Click to collapse
Thank you for a link to the post with a working zip file for adb, I've downloaded and I've tried to follow the video, but unfortunately my laptop will not read my nook at all. Every time I connect it with a usb my device manager tries to find it, but it blinks, makes an error sound and I see
OMAP4330 under other devices. I' did a search for that error and came across this thread, but again the instructions call for installing an apk on the nook and since I can't get mine to turn on, it's a no go
evm22 said:
Thank you for a link to the post with a working zip file for adb, I've downloaded and I've tried to follow the video, but unfortunately my laptop will not read my nook at all. Every time I connect it with a usb my device manager tries to find it, but it blinks, makes an error sound and I see
OMAP4330 under other devices. I' did a search for that error and came across this thread, but again the instructions call for installing an apk on the nook and since I can't get mine to turn on, it's a no go
Click to expand...
Click to collapse
There is a possibility you could have deleted some partitions important to the nook then. Have you tried making an sdc version of cm10 to see if it could boot at all? You could see if you still have the device information to backup, recreate the partitions and flash back to stock.
Use this to make a bootable cm10 card:
http://iamafanof.wordpress.com/2012/11/18/cm10-0-jellybean-sdcard-img-for-nook-tablet/
Just write the image file to an SD card and put it in your nook. It will boot into cm10. Once there go into your file manager and turn on root access. Go to your root drive/ROM/devconf to access all your device information. Make a backup of all them. There is a picture of my devices root drive. If you do not have the various partitions you will have to recreate them. There is a method on the Nook General Thread for doing this named "Unbrick Internal Partitions On NT" or something similar. You can use that recreate the internal partitions essential for your nook.
If you deleted the ROM partition with the Nook's product information you may be out of luck. The serial number and Mac address are the most essential, and can be found on your device hardware. The SN is under the SD slot (if readable) and Mac address is located inside your device. Not sure where I've never opened my nook to look, but probably on the WiFi chip.
Slight chance you may be able to fix it with this information and the rest of the device information you can use from a different nook since it doesn't have to do with internet and registration. There may be a way to fix that, but I don't know of any.
Best of luck. If you have problems just post a reply or send me an email.
I can get the Nook to turn on with the bootable cm10 card in it. I get the cyanoboot screen and see the boot menu, but honestly I don't know where to go from there. I think it's time for me to try and find someone who understands all of the programs involved in trying to fix this because I know I'm going to end up making things worse, if that's even possible. Thank you for trying to help me though. I do appreciate it
evm22 said:
I can get the Nook to turn on with the bootable cm10 card in it. I get the cyanoboot screen and see the boot menu, but honestly I don't know where to go from there. I think it's time for me to try and find someone who understands all of the programs involved in trying to fix this because I know I'm going to end up making things worse, if that's even possible. Thank you for trying to help me though. I do appreciate it
Click to expand...
Click to collapse
Hello! Did you ever figure out how to resurrect your Nook? I had trouble signing in Gmail and wanted to just unbrick and have the plain Nook again. I've been struggling getting the device to boot from the sd card with the repart imaged. I'm trying to get back to the ClockworkMod recovery screen but I can't at that moment. Someone suggested that I "flash" the B&N zip to the card but I'm trying to figure out how to do that.
Would love help!
Hey! I am trying to get Cyanogenmod 12.1 on my stock Nook Tablet. I no longer use the Nook Tablet as often and would like to give it a new life by making it an Android. After reading a ton of articles and forums, I have tried a ton of them, but none of them seem to work successfully. One of them I tried was, Install CM for acclaim on the wiki.cyanogenmod.org website , the process went successfully until I rebooted and it continued to boot me to the regular Nook setup. I think it is because the Clockworkmod Recovery is outdated. I also see that Cyanogenmod's latest recovery is also available, but how do I put it on my SD card successfully. Please provide a step to step guide for me. Thank you!
BornReady_ said:
Hey! I am trying to get Cyanogenmod 12.1 on my stock Nook Tablet. I no longer use the Nook Tablet as often and would like to give it a new life by making it an Android. After reading a ton of articles and forums, I have tried a ton of them, but none of them seem to work successfully. One of them I tried was, Install CM for acclaim on the wiki.cyanogenmod.org website , the process went successfully until I rebooted and it continued to boot me to the regular Nook setup. I think it is because the Clockworkmod Recovery is outdated. I also see that Cyanogenmod's latest recovery is also available, but how do I put it on my SD card successfully. Please provide a step to step guide for me. Thank you!
Click to expand...
Click to collapse
I just did this about a week ago (finally) and there are no better instructions for getting started than those provided by digixmax here. Just ignore the statements about CM 11 and forge ahead. Later in that thread there are a variety of recommendations for file substitutions in the method if you are aiming for CM 12 instead of 11. I followed the ones here. These also work.
My own discovery was that you should ignore the TWRP error messages about being unable to mount '/bootdata'. I finally came across that somewhere and it proved to be true for me.
Take it slow. Gather together all the files you will need first. Then prep the SD card (don't forget to set the flag). Then copy the files over in the order specified. It matters. Then go for it! (don't neglect to backup the stock system before wiping things--you may be glad you did).
My start-up with CM 12.1 was really rough and I thought I might abandon it but after a few days and quite a number of reboots things settled down. Maybe that has something to do with coming from CM 10.2.1, maybe not. Anyway, the system is no worse than CM 10.2.1 and I don't have trouble with cold or warm boots hanging like I used to with CM 10.2.1.
My pet peeves are listed here and/or here but may be idiosynchratic to my device or particular flash.
nmyshkin said:
I just did this about a week ago (finally) and there are no better instructions for getting started than those provided by digixmax here. Just ignore the statements about CM 11 and forge ahead. Later in that thread there are a variety of recommendations for file substitutions in the method if you are aiming for CM 12 instead of 11. I followed the ones here. These also work.
My own discovery was that you should ignore the TWRP error messages about being unable to mount '/bootdata'. I finally came across that somewhere and it proved to be true for me.
Take it slow. Gather together all the files you will need first. Then prep the SD card (don't forget to set the flag). Then copy the files over in the order specified. It matters. Then go for it! (don't neglect to backup the stock system before wiping things--you may be glad you did).
My start-up with CM 12.1 was really rough and I thought I might abandon it but after a few days and quite a number of reboots things settled down. Maybe that has something to do with coming from CM 10.2.1, maybe not. Anyway, the system is no worse than CM 10.2.1 and I don't have trouble with cold or warm boots hanging like I used to with CM 10.2.1.
My pet peeves are listed here and/or here but may be idiosynchratic to my device or particular flash.
Click to expand...
Click to collapse
I literally just finished sending a message to digixmax when you posted this. I remember seeing you in the other forum, trying to get CM12.1 to install. I did all this instructions over and over for hours, but I keep getting stuck at the CyanoBoot section. I get the Boot Menu, but then the SDC Recovery option isn't available, I see it, but it isn't clickable.
BornReady_ said:
I literally just finished sending a message to digixmax when you posted this. I remember seeing you in the other forum, trying to get CM12.1 to install. I did all this instructions over and over for hours, but I keep getting stuck at the CyanoBoot section. I get the Boot Menu, but then the SDC Recovery option isn't available, I see it, but it isn't clickable.
Click to expand...
Click to collapse
OK, so as soon as the cyanoboot screen appears you hold down the N button, right?
Also, did you boot with the power cable connected?
nmyshkin said:
OK, so as soon as the cyanoboot screen appears you hold down the N button, right?
Also, did you boot with the power cable connected?
Click to expand...
Click to collapse
Yes, I booted with the power cable connected, I tried on being connected to the laptop and power wall as well. I also held down the N button, which is why I got to the Boot Menu.
Bear with me
Are you sure you got the SD card version of TWRP?
Yes, 100% sure.
BornReady_ said:
Yes, 100% sure.
Click to expand...
Click to collapse
Well that was interesting! We're "live" apparently
I want to help but I'm not digixmax... I'll bet he has an idea. Wait for him to get back to you while I rummage around.
Lol, thanks for the help anyways though. I will have to wait for digixmax.
Wow, everytime you mention digixmax, he replies. He just privated messaged me in return.
If you can get to the CyanoBoot menu but its menu entry for "SDC recovery" is greyed out then it's because CyanoBoot (flashing_boot.img) cannot find a recovery.img file on your bootable SDcard.
Which version of SD-based recovery did you download and use?
You might want to wait for and check against the answer to my inquiry post at http://forum.xda-developers.com/showpost.php?p=65016892&postcount=41 (I no longer have a NT and as such cannot vouch for any specific recent recovery versions).
I'm sorry, I should have been more precise. I don't know if it will help, but this is the TWRP recovery image I used successfully when I tried this process. That's v. 2.8.6.0
digixmax said:
If you can get to the CyanoBoot menu but its menu entry for "SDC recovery" is greyed out then it's because CyanoBoot (flashing_boot.img) cannot find a recovery.img file on your bootable SDcard.
Which version of SD-based recovery did you download and use?
You might want to wait for and check against the answer to my inquiry post at http://forum.xda-developers.com/showpost.php?p=65016892&postcount=41 (I no longer have a NT and as such cannot vouch for any specific recent recovery versions).
Click to expand...
Click to collapse
I have seen everyone else's folders and they seem to include "flashing_boot.img" However, the file I downloaded from your page only has "flashing_boot" When I try to rename the file, the Nook Tablet won't even turn on anymore at all. Matter of fact, I can't even get to the Boot Menu now, it keeps having that red line that states, "booti: bad boot image magic (in memory)" I'm losing hope...
BornReady_ said:
I have seen everyone else's folders and they seem to include "flashing_boot.img" However, the file I downloaded from your page only has "flashing_boot" When I try to rename the file, the Nook Tablet won't even turn on anymore at all. Matter of fact, I can't even get to the Boot Menu now, it keeps having that red line that states, "booti: bad boot image magic (in memory)" I'm losing hope...
Click to expand...
Click to collapse
Don't give up. If you're using a Windows machine to prepare the card then whether the .IMG is displayed or not depends on your settings. It does not show on mine but a look at the file properties shows it is an .IMG file.
So that's the wrong tree. SDCards have been known to be problematic so if you have another around you might want to give it a try. You also might do a slow (complete) format on it before preparing it from scratch.
The other thing, of course, is the integrity of the individual files. Checking the MD5 values is a pain but sometimes reveals a bad download.
nmyshkin said:
Don't give up. If you're using a Windows machine to prepare the card then whether the .IMG is displayed or not depends on your settings. It does not show on mine but a look at the file properties shows it is an .IMG file.
So that's the wrong tree. SDCards have been known to be problematic so if you have another around you might want to give it a try. You also might do a slow (complete) format on it before preparing it from scratch.
The other thing, of course, is the integrity of the individual files. Checking the MD5 values is a pain but sometimes reveals a bad download.
Click to expand...
Click to collapse
I have tried everything. It doesn't seem to work. I'm also sure there aren't issues with downloading because I have redownloaded the files over 7 times. Is there a way I can download the folder of files that you used to install cyanogenmod?
BornReady_ said:
I have tried everything. It doesn't seem to work. I'm also sure there aren't issues with downloading because I have redownloaded the files over 7 times. Is there a way I can download the folder of files that you used to install cyanogenmod?
Click to expand...
Click to collapse
I've already shut down my computer for the night. I'll have a look at the size that an image of the card would be. Maybe that's the easiest way if there's room in my dropbox. If you've read through the CM11/12 thread you know I ran into problems and if you were to look at the CM10 thread you'd find me floundering around there also, so I know how frustrating it can be. And then suddenly it just works.
I'll let you know tomorrow.
BornReady_ said:
I have seen everyone else's folders and they seem to include "flashing_boot.img" However, the file I downloaded from your page only has "flashing_boot" When I try to rename the file, the Nook Tablet won't even turn on anymore at all. Matter of fact, I can't even get to the Boot Menu now, it keeps having that red line that states, "booti: bad boot image magic (in memory)" I'm losing hope...
Click to expand...
Click to collapse
As @nmyshkin pointed out, it's most likely because your Windows Explorer is configured not to display the file-name extension, so when you try to rename "flashing_boot" to "flashing_boot.img" you in effect end up with a file with name "flashing_boot.img.img".
This is likely also the root cause of your original problem: if you now just rename the TWRP recovery file you had downloaded (which already has the hidden .img extension) to "recovery" (and not "recovery.img" lest you end up with a file named "recovery.img.img") then CyanoBoot will see the recovery file.
For avoidance of doubt, just set your Windows Explorer to display file-name extension.
digixmax said:
As @nmyshkin pointed out, it's most likely because your Windows Explorer is configured not to display the file-name extension, so when you try to rename "flashing_boot" to "flashing_boot.img" you in effect end up with a file with name "flashing_boot.img.img".
This is likely also the root cause of your original problem: if you now just rename the TWRP recovery file you had downloaded (which already has the hidden .img extension) to "recovery" (and not "recovery.img" lest you end up with a file named "recovery.img.img") then CyanoBoot will see the recovery file.
For avoidance of doubt, just set your Windows Explorer to display file-name extension.
Click to expand...
Click to collapse
You are totally correct. I enabled Windows Explorer to display file-name extension and the TWRP recovery file turned out as "recovery.img.img" I am going to try it out now and reply with if it works or not.
Alright, I have been trying and following the instructions clearly, but it keeps giving me the red line stating, "booti: bad boot image magic (in memory)" now. I have gotten to the Boot Menu before, but now it won't even let me get there. What does this message mean?
BornReady_ said:
Alright, I have been trying and following the instructions clearly, but it keeps giving me the red line stating, "booti: bad boot image magic (in memory)" now. I have gotten to the Boot Menu before, but now it won't even let me get there. What does this message mean?
Click to expand...
Click to collapse
Is flashing_boot file on your SD card correctly named "flashing_boot.img", and not "flashing_boot.img.img"?