Hello,
I have a problem unrooting/unbricking my Galaxy S4 for Verizon. I followed step-by-step processes and it seems to not work properly for me. I downloaded "Odin3 v.1.85" and the stock firmware, "GalaxyS4/SCH-i545/VRUAMDK_NoWipe.tar.zip" and "SCH-I545_MDK_562219_Stock_Restore.tar.md5" for Verizon. I put my phone into the Download Mode and began the process of unrooting using Odin. I made sure that my device was connected. I clicked PDA and chose the stock firmware for my phone. I clicked Start and it begins. As soon is it begins, it says it is not responding, but I wait a few seconds and it responds. After that, it continues where it left off for the unrooting process. The process turned out to be a fail. Here's the message:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It has failed and when I attempt to reboot my phone, it gives me a message that says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." I attempted the Kies process, and it would not connect my device to Kies. Please help. I feel as if I were the only user with this problem. Thank you.
sounds like you were already on v7 baseband try getting that stock image and go through odin.
because you cant go back to the original baseband (which is the md5 you listed) but I had similiar issues.
goosedaddy said:
sounds like you were already on v7 baseband try getting that stock image and go through odin.
because you cant go back to the original baseband (which is the md5 you listed) but I had similiar issues.
Click to expand...
Click to collapse
Seems like it's tough luck for me. What do you suggest I do? Did you resolve any of your similar issues?
yep. I only wanted to make sure you did install the update or otherwise some of the 32gb s4 come with it preinstalled.
just saying this because updating to me7 is irreversible you wont be able to flash roms right now only apply a root
download the me7 md5 this time and do all the same steps I followed this guide
http://forum.xda-developers.com/showthread.php?t=2301259
hope this helps
goosedaddy said:
yep. I only wanted to make sure you did install the update or otherwise some of the 32gb s4 come with it preinstalled.
just saying this because updating to me7 is irreversible you wont be able to flash roms right now only apply a root
download the me7 md5 this time and do all the same steps I followed this guide
http://forum.xda-developers.com/showthread.php?t=2301259
hope this helps
Click to expand...
Click to collapse
Alright. I'll follow these steps and I'll get back to here and let you know. Thank you.
I'm in the process of downloading the ME7 you told me about, but isn't this rooting my phone? I want to reformat my phone and have everything wiped out.
MattLife said:
I'm in the process of downloading the ME7 you told me about, but isn't this rooting my phone? I want to reformat my phone and have everything wiped out.
Click to expand...
Click to collapse
nope its a stock image so everything will be like when you first got it. not sure if some data will be there but you will not be rooted.
the root process is here http://forum.xda-developers.com/showthread.php?t=2381382
goosedaddy said:
nope its a stock image so everything will be like when you first got it. not sure if some data will be there but you will not be rooted.
the root process is here http://forum.xda-developers.com/showthread.php?t=2381382
Click to expand...
Click to collapse
This really helped me! Thank you so much! It's been fixed.
MattLife said:
This really helped me! Thank you so much! It's been fixed.
Click to expand...
Click to collapse
Awesome! Glad it all worked out.
help
Trying to unroot and revert to stock and I have soft bricked my galaxy s4! The charging port is gone so I cannot use a computer to fix this...I have searched everywhere for help and am stuck! Anyone have any suggestions???
gregorykbrownjr said:
Trying to unroot and revert to stock and I have soft bricked my galaxy s4! The charging port is gone so I cannot use a computer to fix this...I have searched everywhere for help and am stuck! Anyone have any suggestions???
Click to expand...
Click to collapse
if you can't get the usb port (charging port) to work with communicating to your computer then there really isn't much you can do. Have you tried cleaning the contacts off inside the port? Are you sure its NOT the cable?
This has been talked about somewhere else here in this forum
Same problem
goosedaddy said:
sounds like you were already on v7 baseband try getting that stock image and go through odin.
because you cant go back to the original baseband (which is the md5 you listed) but I had similiar issues.
Click to expand...
Click to collapse
Hey I have the exact same issue but with the international LTE galaxy s4 do you have any idea what i can do i have put the GPE rom on this and i found that flashing TWRP when it gave me the kies error bought me back to my GPE rom i'm going to sell this phone and i need to return to stock firmware should i try a new computer or something else please help me i've been really scared, i would appreciate it if you can help me in any way.
Related
I have the Bell GSIII (i747) and I bricked it while playing around with the Toolkit. I downloaded the stock firmware from here, but whenever I flash it, Odin says this:
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
and by phone says: "SECURE CHECK FAIL: aboot"
aboot.mbn is a file inside the tar.
I can access Recovery and Download mode easily, but the problem is that when my phone boots, It flashes SAMSUNG, and then Samsung Galaxy S III, but then the screen goes black. To reboot it again, I have to pull the battery.
Any help would be greatly appreciated, thanks!
--Jeremy
http://forum.xda-developers.com/showthread.php?t=1727443
You can try that thread there. The same thing you are experiencing has happened before I Hard Bricked my phone.
Just be careful when you are messing around with the S3 it can be so confusing with all the S3 Variants out there.
Hopefully this will workout for ya
Fuzz21 said:
http://forum.xda-developers.com/showthread.php?t=1727443
You can try that thread there. The same thing you are experiencing has happened before I Hard Bricked my phone.
Just be careful when you are messing around with the S3 it can be so confusing with all the S3 Variants out there.
Hopefully this will workout for ya
Click to expand...
Click to collapse
Yeah, I'm reading this now. I just did what it said, but still no dice.
JibbsIsMe said:
I have the Bell GSIII (i747) and I bricked it while playing around with the Toolkit. I downloaded the stock firmware from here, but whenever I flash it, Odin says this:
and by phone says: "SECURE CHECK FAIL: aboot"
aboot.mbn is a file inside the tar.
I can access Recovery and Download mode easily, but the problem is that when my phone boots, It flashes SAMSUNG, and then Samsung Galaxy S III, but then the screen goes black. To reboot it again, I have to pull the battery.
Any help would be greatly appreciated, thanks!
--Jeremy
Click to expand...
Click to collapse
Can you flash a rom in recovery? Also do you have Odin set to the correct settings?
I had a problem with mine where Odin wasn't doing anything at all. It would start but never finished. I changed the USB port and was good after that. Weird because my sgs2 and sgs3 international were fine using the one USB port. Just a thought to try a different port if it stops or fails
Sent from my SGH-I747M using xda app-developers app
brfield said:
Can you flash a rom in recovery? Also do you have Odin set to the correct settings?
Click to expand...
Click to collapse
I can't flash ROMs, since I can't seem to figure out how to get things onto my SD card or my External SD Card.
Problem solved!
JibbsIsMe said:
I can't flash ROMs, since I can't seem to figure out how to get things onto my SD card or my External SD Card.
Click to expand...
Click to collapse
OK, I got it. First, I followed this: http://www.epiccm.org/2012/06/cwm-recovery-on-all-sgs3-lte-variants.html
I stopped right after step 8. I then put my Ext SD into my old phone, formatted it, and put on this: http://forum.xda-developers.com/showthread.php?t=1732191
Then I went into recovery, and flashed that ROM. Then rebooted, and I'm fine now! YAY!
I almost wasted $730....
--Jeremy
Awesome stuff !!
Mine is still a 500$ paper weight, LOL hopefully I can fix it :S
Good luck, I would hate to lose my phone on it's first day...
JibbsIsMe said:
Good luck, I would hate to lose my phone on it's first day...
Click to expand...
Click to collapse
Thanks budd
I really hope I can resurrect it from the Dead.
JibbsIsMe said:
I have the Bell GSIII (i747) and I bricked it while playing around with the Toolkit. I downloaded the stock firmware from here, but whenever I flash it, Odin says this:
and by phone says: "SECURE CHECK FAIL: aboot"
aboot.mbn is a file inside the tar.
I can access Recovery and Download mode easily, but the problem is that when my phone boots, It flashes SAMSUNG, and then Samsung Galaxy S III, but then the screen goes black. To reboot it again, I have to pull the battery.
Any help would be greatly appreciated, thanks!
--Jeremy
Click to expand...
Click to collapse
I hate to threadjack, but this is the only thread I can find mention of this error with the sgs3 with.
mine did the same thing last night, thought I bricked.. but it didnt brick, used the phone all day today with no problems, tried to root again today with at&t method with odin, and I keep getting the same error. Its a bell i747m using odin 3.0.7
Any ideas?
Edit: Also I have tried several usb ports and a couple different cables.
Hi i've had CM9 in my phone for a half year now without any issues, however two days ago i woke up and went to check my phone, it froze and after that i haven't been able to boot it up, it just hungs at the samsung logo with the triangle and all that, so i've been trying to sort out this for two days straight now and i'm getting really sick of this, what i've done so far is:
* tried to flash alot of rom's and such with no success, stucks at: NAND Write Start!!
* tried to flash on a different computer
* tried to flash with different usb ports
Oh and i can't get into the recovery mode, only the download mode.
This is the files i've tried to flash and such to get my phone working again:
Kernel_I9100XXLPH
I9100XXLPQ_I9100HTSLP3_HTS
I9100XWLPG_I9100XXLPX_I9100NEELP4_NEE
I9100XWLPG_I9100XXLPX_I9100NEELP4_HOME.tar
I9100XWLPG_I9100NEELP4_NEE
GT-I9100_Kernel_Gingerbread-supercurio-3
GT-I9100_ICS_ClockworkMod-Recovery_5.5.0.4
cm-10-20120927-EXPERIMENTAL-i9100-jb_mali-changmin
cm-10-20120926-NIGHTLY-i9100
cm-9-20120330-ODIN-galaxys2.tar
CF-Root-SGS2_XW_NEE_LPG-v5.5-CWM5
CF-Root-SGS2_XX_OXA_KP8-v5.2-CWM5
GT-I9100_NEE_I9100XWLPD_I9100XXLPW_I9100NEELP4
Please, can anyone try to help me? I can't explain how tired i am of this, i really need and want my phone to work again! Thanks
Emperia said:
Hi i've had CM9 in my phone for a half year now without any issues, however two days ago i woke up and went to check my phone, it froze and after that i haven't been able to boot it up, it just hungs at the samsung logo with the triangle and all that, so i've been trying to sort out this for two days straight now and i'm getting really sick of this, what i've done so far is:
* tried to flash alot of rom's and such with no success, stucks at: NAND Write Start!!
* tried to flash on a different computer
* tried to flash with different usb ports
Oh and i can't get into the recovery mode, only the download mode.
This is the files i've tried to flash and such to get my phone working again:
Kernel_I9100XXLPH
I9100XXLPQ_I9100HTSLP3_HTS
I9100XWLPG_I9100XXLPX_I9100NEELP4_NEE
I9100XWLPG_I9100XXLPX_I9100NEELP4_HOME.tar
I9100XWLPG_I9100NEELP4_NEE
GT-I9100_Kernel_Gingerbread-supercurio-3
GT-I9100_ICS_ClockworkMod-Recovery_5.5.0.4
cm-10-20120927-EXPERIMENTAL-i9100-jb_mali-changmin
cm-10-20120926-NIGHTLY-i9100
cm-9-20120330-ODIN-galaxys2.tar
CF-Root-SGS2_XW_NEE_LPG-v5.5-CWM5
CF-Root-SGS2_XX_OXA_KP8-v5.2-CWM5
GT-I9100_NEE_I9100XWLPD_I9100XXLPW_I9100NEELP4
Please, can anyone try to help me? I can't explain how tired i am of this, i really need and want my phone to work again! Thanks
Click to expand...
Click to collapse
try flashing a stockfirmware which comes with a .pit file and see
Sun90 said:
try flashing a stockfirmware which comes with a .pit file and see
Click to expand...
Click to collapse
Could you please help me out, i'm not really sure where i can find that.
Edit: I live in Sweden, Europe so i need a nordic firmware.
Emperia said:
Could you please help me out, i'm not really sure where i can find that.
Edit: I live in Sweden, Europe so i need a nordic firmware.
Click to expand...
Click to collapse
check the link below read the main post(#1) of that thread and proceed carefully to revive back ur phone
http://forum.xda-developers.com/showthread.php?t=1457458
Sun90 said:
check the link below read the main post(#1) of that thread and proceed carefully to revive back ur phone
http://forum.xda-developers.com/showthread.php?t=1457458
Click to expand...
Click to collapse
Thanks, i've read that guide earlier and tried a few steps with no luck.
Is this what i should do?
"WARNING : FLASHING A BOOTLOADER IS DANGEROUS. FLASH WITH EXTREME CAUTION.
8) Download the Bootloader. Flash it as PDA or Bootloader in ODIN. Without ticking Re-Partitioning
9) Flash the Kernel, as in step 5
10) Flash the recovery package, like in steps 1-4 And that will fix any of your issues "
Emperia said:
Thanks, i've read that guide earlier and tried a few steps with no luck.
Is this what i should do?
"WARNING : FLASHING A BOOTLOADER IS DANGEROUS. FLASH WITH EXTREME CAUTION.
8) Download the Bootloader. Flash it as PDA or Bootloader in ODIN. Without ticking Re-Partitioning
9) Flash the Kernel, as in step 5
10) Flash the recovery package, like in steps 1-4 And that will fix any of your issues "
Click to expand...
Click to collapse
no dont mess with that 'Bootloader' one ma8, there is one on how to use pit file look into that
look for this in that thread
Recovering a soft bricked phone
1) Grab the Recovery Package, and you'll see a bunch of .tar files. Take a look at the names. You'll see CODE, MODEM, CSC and .PIT. Put each one in its place.
2) Turn off your phone. Enter Download mode by presing Volume Down + Home + Power button.
3) Plug in your phone. It will show you, in a yellow box in ODIN, ID:COMx (x being the number displayed, sometimes displays 7, sometimes displays 9)
Now here, take a breath
First try flashing WITHOUT the .PIT and re-partition. And only if it DOESN'T WORK OR FIX then you flash with the .PIT and Re-Partition ticked.
4) Once ready and done all your prayers, press Start. Wait patiently. It usually takes 5 minutes to flash.
Have you done everything correctly until now? Then...
Congratulations on recovering your phone!
Sun90 said:
no dont mess with that 'Bootloader' one ma8, there is one on how to use pit file look into that
Click to expand...
Click to collapse
Hmm, well the only files i got when i downloaded the recovery package via that thread is:
MODEM_I9100XXLPH_REV_02_CL1104396.tar
I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar
I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar
GT-I9100-MULTI-CSC-OXALPH.tar
thanks for trying to help me, it's appreciated!
Emperia said:
Hmm, well the only files i got when i downloaded the recovery package via that thread is:
MODEM_I9100XXLPH_REV_02_CL1104396.tar
I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar
I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar
GT-I9100-MULTI-CSC-OXALPH.tar
thanks for trying to help me, it's appreciated!
Click to expand...
Click to collapse
did u dwnld'd that file under Gingerbread or ICS?
Sun90 said:
did u dwnld'd that file under Gingerbread or ICS?
Click to expand...
Click to collapse
The ICS one, is that wrong?
Emperia said:
The ICS one, is that wrong?
Click to expand...
Click to collapse
yes its correct, The ICS one is the right one for u
now follow the instruction over that thread for where to put those files in ODIN and flash the same
Sun90 said:
yes its correct, The ICS one is the right one for u
now follow the instruction over that thread for where to put those files in ODIN and flash the same
Click to expand...
Click to collapse
Alright, we'll see what happens, there is no pit file thought, correct?
Emperia said:
Alright, we'll see what happens, there is no pit file thought, correct?
Click to expand...
Click to collapse
its only needed in the worst case scenerio
Sun90 said:
its only needed in the worst case scenerio
Click to expand...
Click to collapse
Ah alright, so i should put all those files even the bootloader in odin and try to flash? Just making sure!
Emperia said:
Ah alright, so i should put all those files even the bootloader in odin and try to flash? Just making sure!
Click to expand...
Click to collapse
yes
ps- and remember that u r doing all this thing at ur own risk, do not complain in the Future if something goes wrong there
Sun90 said:
yes
Click to expand...
Click to collapse
This is what happens:
Code:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
Emperia said:
This is what happens:
Code:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.bin
<ID:0/006> NAND Write Start!!
Click to expand...
Click to collapse
do u see a red 'fail' message in the big rectangle box in odin
Sun90 said:
do u see a red 'fail' message in the big rectangle box in odin
Click to expand...
Click to collapse
Nope, it just seems like it's stuck, this is what always happens, i never get fail messages or such.
Emperia said:
Nope, it just seems like it's stuck, this is what always happens, i never get fail messages or such.
Click to expand...
Click to collapse
which version of windows ur using is it XP or 7
Sun90 said:
which version of windows ur using is it XP or 7
Click to expand...
Click to collapse
Windows 7, i've tried to flash on windows xp as well, and it gets stuck too, no fail error.
Emperia said:
Windows 7, i've tried to flash on windows xp as well, and it gets stuck too, no fail error.
Click to expand...
Click to collapse
try to reflash using the PIT file att below, extract the file put it in the pit section on odin along with the other files in there respective section also check the re-partition and see
I'm interested in rooting my new Galaxy S4 but I also would like the original stock rom in case if I ever need to go back to it. Would anyone by any chance have the original stock ROM?
Model: SCH-I545
Android Version: 4.2.2
*If any other details are needed, let me know.
This is a Verizon phone fyi.
Also, could someone please link me to a tutorial/guide for rooting the S4 and some other links that have ROMs that are a "must-get".
Thanks,
Hydra
Read the development forums. The stock image is ready enough to find, as are step by step root instructions. As to your last question, that is the type of thing that gets a thread locked. Read the dev forums, pick a few roms that pique your interest, and give them a test drive.
Sent from my Nexus 7 using Tapatalk HD
najaboy said:
Read the development forums. The stock image is ready enough to find, as are step by step root instructions. As to your last question, that is the type of thing that gets a thread locked. Read the dev forums, pick a few roms that pique your interest, and give them a test drive.
Sent from my Nexus 7 using Tapatalk HD
Click to expand...
Click to collapse
I'm new here so tried my best to find the correct section, and did search for guides.
I'm currently using this guide, http://forum.xda-developers.com/showthread.php?t=2290798 , but upon flashing the prerelease kernal, it failed.
http://i.imgur.com/MjbRPrK.png
Also, in case of anything, how can I leave ODIN mode on the phone? Do I just power it off and reboot?
CM10.1 has been treating me pretty well. Haven't had any crashes or anything and runs fast and stable.
The only issue I noticed is you can't get a GPS lock while Network & Wireless location is on. Once you disable it GPS locks right in.
Sent from my SCH-I545 using Tapatalk 2
I now have a huge problem. I'm at the screen: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Need to resolve this as soon as possible.
HydraS4 said:
I now have a huge problem. I'm at the screen: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Need to resolve this as soon as possible.
Click to expand...
Click to collapse
Go to this guide and download the .tar image to be used in Odin http://forum.xda-developers.com/showthread.php?t=2301259. Boot into Odin mode following this guide http://forum.xda-developers.com/showthread.php?t=2290771. Follow all the instructions exactly and ask questions here if you have any.
Ryno77 said:
Go to this guide and download the .tar image to be used in Odin http://forum.xda-developers.com/showthread.php?t=2301259. Boot into Odin mode following this guide http://forum.xda-developers.com/showthread.php?t=2290771. Follow all the instructions exactly and ask questions here if you have any.
Click to expand...
Click to collapse
The tar file is 1.8 Gbs, is this the only method? I have horrible download speed and going to take 3 hours to download it.
Btw, can someone educate me on what just happened? Did I brick my phone? Will I lose any data?
Thanks,
Hydra
HydraS4 said:
The tar file is 1.8 Gbs, is this the only method? I have horrible download speed and going to take 3 hours to download it.
Btw, can someone educate me on what just happened? Did I brick my phone? Will I lose any data?
Thanks,
Hydra
Click to expand...
Click to collapse
Can you get into regular android recovery?
Ryno77 said:
Can you get into regular android recovery?
Click to expand...
Click to collapse
Nope, I'm working on trying Samsung Kies, maybe that will do it but I tried to get into recovery mode thru the phone but takes me to that same window.
I'm also downloading the stock firmware.
Did you try just flashing the stock kernel back using Odin? Everything you've done is listed in this thread, right? Technically if you tried to flash the pre release kernel and it failed nothing should have happened.
Ryno77 said:
Did you try just flashing the stock kernel back using Odin? Everything you've done is listed in this thread, right?
Click to expand...
Click to collapse
No, I haven't. Is that the one in the guide? If so, I'll do it soon. I have to go out, and now without a phone so going to be a problem for me.
Thanks for the quick support btw, appreciate it.
HydraS4 said:
No, I haven't. Is that the one in the guide? If so, I'll do it soon. I have to go out, and now without a phone so going to be a problem for me.
Thanks for the quick support btw, appreciate it.
Click to expand...
Click to collapse
I don't know if it will work but it's worth trying. The stock Odin should definitely fix your problem though. Yes it's in the thread.
Ryno77 said:
I don't know if it will work but it's worth trying. The stock Odin should definitely fix your problem though. Yes it's in the thread.
Click to expand...
Click to collapse
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Kernel.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Is what I get upon flashing kernel to the stock kernel. I am downloading the stock ROM as I type this. 1 Hour left to download it. Btw, does it matter what type of ROM I download?
Is there a difference from, http://www.rwilco12.com/downloads.p...Galaxy S4 (Verizon) (SCH-I545)/Stock ROMs/TAR and http://forum.xda-developers.com/showthread.php?t=2301259 ?
I'm guessing it's the No Wipe feature?
And what's the worst case scenario with rooting the phone? Anything permanent? If this stock ROM fixes the current problem, then I'll attempt to root once more.
Thanks,
Hydra
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Removed!!
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
What is the PIT partition? Is that my internal storage?
Are you using the factory charging cable to connect to the computer? I don't know why everything keeps failing.... Odin has never failed for me. Do you have another computer you can try this on? Stock charging cable, different usb port or another computer are the things I would try next. I don't know anything about pit files.
Sent from my SCH-I545 using xda premium
Ryno77 said:
Are you using the factory charging cable to connect to the computer? I don't know why everything keeps failing.... Odin has never failed for me. Do you have another computer you can try this on? Stock charging cable, different usb port or another computer are the things I would try next. I don't know anything about pit files.
Sent from my SCH-I545 using xda premium
Click to expand...
Click to collapse
Tried two types of cables, a generic one and factory/original one. I tried two different computers with 2 different OS. Tried 3 different ports per computer.
Don't know what else I can do.
Since you're able to boot into Odin mode I think this can be fixed but it may require a pit file. Since I know nothing about pit files or why Odin kept failing for you I'm going to let someone else try and help you. I do not think your phone is beyond hope at this point. Good luck.... I hope someone chimes in with the help you need.
Sent from my SCH-I545 using xda premium
Ryno77 said:
Since you're able to boot into Odin mode I think this can be fixed but it may require a pit file. Since I know nothing about pit files or why Odin kept failing for you I'm going to let someone else try and help you. I do not think your phone is beyond hope at this point. Good luck.... I hope someone chimes in with the help you need.
Sent from my SCH-I545 using xda premium
Click to expand...
Click to collapse
Alright, I appreciate all the help. Thanks!
Hopefully someone can help me out before I head over to Verizon later today.
HydraS4 said:
Alright, I appreciate all the help. Thanks!
Hopefully someone can help me out before I head over to Verizon later today.
Click to expand...
Click to collapse
Yeah, no problem. I'm sorry nothing worked for you.
Sent from my SCH-I545 using xda premium
Does anyone know if Verizon will replace it if it isn't my fault? There is no proof of rooting just a messed up system.
Hey guys. I've run into an issue with my GT-i9300 International version just yesterday at it's racking my brains up.
Here's the lowdown about the device
It's the international GTi9300 (3G version)
It runs ArchiDroid v2.1.4 ROM
This rom was installed a year ago and gave no issues what so ever.
Just yesterday the device did not boot up. i Managed to get it into philz recovery to see whats the problem. i get the error message that it couldnt mount /data, /system & etc.
I have posted the screenshots. I've tried backing up, mounting and even factory wiping but it does not work
I have a feeling the eMMC flash storage has failed and therefore i have a hardware failure :crying:
I hope this is not the case since i have lots of important data on this phone (it's my secondary phone)
Have a look at the screens. lemme know the fate of my S3, whether it is possible to recover this device or not
p.s: I've checked all over the net. i've only come across the /efs not mounting issue. not what im going through
Naweed Reza said:
Hey guys. I've run into an issue with my GT-i9300 International version just yesterday at it's racking my brains up.
Here's the lowdown about the device
It's the international GTi9300 (3G version)
It runs ArchiDroid v2.1.4 ROM
This rom was installed a year ago and gave no issues what so ever.
Just yesterday the device did not boot up. i Managed to get it into philz recovery to see whats the problem. i get the error message that it couldnt mount /data, /system & etc.
I have posted the screenshots. I've tried backing up, mounting and even factory wiping but it does not work
I have a feeling the eMMC flash storage has failed and therefore i have a hardware failure :crying:
I hope this is not the case since i have lots of important data on this phone (it's my secondary phone)
Have a look at the screens. lemme know the fate of my S3, whether it is possible to recover this device or not
p.s: I've checked all over the net. i've only come across the /efs not mounting issue. not what im going through
Click to expand...
Click to collapse
Have you flashed stock firmware with Odin yet? This is the first thing you need to do to see if Odin works or gives errors....don't forget to factory reset after flashing. I'm afraid you may have to live with losing your data if you can't back it up in recovery.
tallman43 said:
Have you flashed stock firmware with Odin yet? This is the first thing you need to do to see if Odin works or gives errors....don't forget to factory reset after flashing. I'm afraid you may have to live with losing your data if you can't back it up in recovery.
Click to expand...
Click to collapse
i'll try flashing the stock rom via odin
Yeah, now i gave up on caring about the data. i really need the phone to work tho
i'll get back on the progress
@tallman43
Status report.
I tried flashing a stock rom which is on 4.3
It says NAND write failure. screenshot uploaded.
So i'm guessing my eMMC is corrupt or has failed :crying:
I did more research and found out that i could repartition it using a .pit file
This thread shows the relevant pit files
http://forum.xda-developers.com/showthread.php?p=30547929#post30547929
GT-I9300_mx_20120220.pit is for the 16 gb s3.
i'll flash with with the ROM
Lemme know if this is alright :good:
Naweed Reza said:
@tallman43
Status report.
I tried flashing a stock rom which is on 4.3
It says NAND write failure. screenshot uploaded.
So i'm guessing my eMMC is corrupt or has failed :crying:
I did more research and found out that i could repartition it using a .pit file
This thread shows the relevant pit files
http://forum.xda-developers.com/showthread.php?p=30547929#post30547929
GT-I9300_mx_20120220.pit is for the 16 gb s3.
i'll flash with with the ROM
Lemme know if this is alright :good:
Click to expand...
Click to collapse
Be careful the thread is for verizon you can't flash any pit files from there be 100% sure the pit file is for S3 international try looking here this is the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << there is a pit file in the 4.1.2 download but you need to flash the 4.3 in the link to stop efs issues. But to be honest it doesn't look too good if this fails I recommend a service repair.
tallman43 said:
Have you flashed stock firmware with Odin yet? This is the first thing you need to do to see if Odin works or gives errors....don't forget to factory reset after flashing. I'm afraid you may have to live with losing your data if you can't back it up in recovery.
Click to expand...
Click to collapse
Tried flashing the pit. I got the following error messages on odin
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMK6_I9300OXAGMK6_I9300XXUGMK6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
tallman43 said:
Be careful the thread is for verizon you can't flash any pit files from there be 100% sure the pit file is for S3 international try looking here this is the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6 << there is a pit file in the 4.1.2 download but you need to flash the 4.3 in the link to stop efs issues. But to be honest it doesn't look too good if this fails I recommend a service repair.
Click to expand...
Click to collapse
I had downloaded the pit from another site. it was the international one
But i'll try your link. i just saw your reply
I'm downloading the 4.3 GT-I9300XXUGMJ9_KOR_MULTI_FACTORY package
Naweed Reza said:
Tried flashing the pit. I got the following error messages on odin
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMK6_I9300OXAGMK6_I9300XXUGMK6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
You need to flash everything at once pit file and rom look at the link I sent you but it looks like you need a new motherboard:crying:
tallman43 said:
You need to flash everything at once pit file and rom look at the link I sent you but it looks like you need a new motherboard:crying:
Click to expand...
Click to collapse
Oh maan
Last resort is the link you gave. i'm downloading the 4.3 package. will put everything and flash at once. if this doest work. rip i guess :/
I never did anything. I installed the custom rom a year ago and let the phone be. didnt bother tweaking or adding to the custom rom
Then all of a sudden it doesnt boot
Naweed Reza said:
@tallman43
Status report.
I tried flashing a stock rom which is on 4.3
It says NAND write failure. screenshot uploaded.
So i'm guessing my eMMC is corrupt or has failed :crying:
I did more research and found out that i could repartition it using a .pit file
This thread shows the relevant pit files
http://forum.xda-developers.com/showthread.php?p=30547929#post30547929
GT-I9300_mx_20120220.pit is for the 16 gb s3.
i'll flash with with the ROM
Lemme know if this is alright :good:
Click to expand...
Click to collapse
I have a feeling the eMMC flash storage has failed and therefore i have a hardware failure
This is true
So flashing all 4 stock files (including pit) via odin turned out to be a Fail
I guess the eMMC is not functional resulting in a hardware failure
Thanks for the help @tallman43
If anyone else has suggestions, feel free to post them here
Dz-Horse said:
I have a feeling the eMMC flash storage has failed and therefore i have a hardware failure
This is true
Click to expand...
Click to collapse
Has this happened to your S3?
I havent tinkered with anything and this happens
I just installed a ROm and left it for a year
Oh well
Yes it happened to me same problem
Looks like the rollout today came in 2 updates. I downloaded the first and installed with no problem but the 2nd which actually puts in lolipop can't install. It says error 402, google/the Verizon forums doesn't have any info on it.
I have the same issue. I have tried Wifi and the Verizon Software Assistant download, and neither works. I am on the hunt for any suggestions as to how to get past this. Since I have just Factory Reset my phone, I will try pretty much anything.
I had 402 error. I downloaded I545VRUFNK1_I545VZWFNK1_I545VRUFNK1_HOME.tar from here:
http://forum.xda-developers.com/gal...-to-root-i545vrufnk1-4-4-2-12-1-2014-t2959613
Extract the .tar file
Install with Odin v3.09+ (put the .tar file in AP slot) and put phone in download mode
It will keep all data.
After reboot install both updates again.
do_9999 said:
I had 402 error. I downloaded I545VRUFNK1_I545VZWFNK1_I545VRUFNK1_HOME.tar from here:
http://forum.xda-developers.com/gal...-to-root-i545vrufnk1-4-4-2-12-1-2014-t2959613
Extract the .tar file
Install with Odin v3.09+ (put the .tar file in AP slot) and put phone in download mode
It will keep all data.
After reboot install both updates again.
Click to expand...
Click to collapse
were you able to root after the updates?
meazz1 said:
were you able to root after the updates?
Click to expand...
Click to collapse
Negative. But I knew that before.
If you're having trouble with the Odin portion of this, check to see if you're using USB 2.0 or USB 3.0 port. My issues seemed to be directly related to using 3.0. No idea why, or whether or not this is a known thing but I'm Odin-ing successfully right now. I'm leaving the "struggle" report in case it might help somebody who has gone through the same process unsuccessfully. Cheers
Followed the Odin instructions. Get a Fail. Using original cable. Here's the log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I545VRUFNK1_I545VZWFNK1_I545VRUFNK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
I made it to NK4 on the OTAs so maybe flashing NK1 won't work? Gonna try the NG6 and NK1 FULL WIPE Odin file. (found here: https://www.androidfilehost.com/?fid=95916177934540736)
The good news is that I can still get into download mode after a battery pull so I'm just going to try and find another Odin file.
Tried using a Pit file given there's no partition. Didn't work. Looks like I've got a morning of thread crawling to look forward to.
As crazy as this might sound, I found the answer for me on Verizon's actual forums from a Verizon customer service rep! That NEVER happens. I almost entirely dismissed it. He told someone asking about this problem, "If that doesn't work, the manufacturer has another way to install the update." I thought that sounding interesting. The link took me to Samsung Kies (an app for the PC) and there you have a choice to install either Kies or Kies3. For some reason it suggests we need Kies, but Kies3 is actually what we need as our S4's have been updated beyond when this site was created.
After installing that, the app TRIES to suggest that we're better off with Smart-something or other, but that's just for transferring contacts and such between two phones. Ignore that and just connect your phone via cable to the PC and Kies will see it and tell you there's an update. It then installed the update without a hitch!
What's amazing is that I also own a Samsung Galaxy Note Pro (the 12.2 inch tablet) that had some issues. However, it would never say there was any sort of update and I could never find one mentioned online. Kies said there was one and installed it. Now the tablet's snappier and better than ever. What a surprise find....
Agrajag27 - OMG, thank you very much! That worked, simple update, and I am on lollipop! Great find!