hello
i just buy my z ultra and when i boot it up for the first time
this problem just came out every time that i press the power button to unlock the screen
i have to press the power button so many times to unlock it
the power button is not the problem cuz i try to take a screen shot and it works very well
+ i did factory data reset
but still the same
any help please ?
Up
magic moon said:
Up
Click to expand...
Click to collapse
send it back... i have the same issue too
http://www.youtube.com/watch?v=-GwSVfSO4Vw
magic moon said:
hello
i just buy my z ultra and when i boot it up for the first time
this problem just came out every time that i press the power button to unlock the screen
i have to press the power button so many times to unlock it
the power button is not the problem cuz i try to take a screen shot and it works very well
+ i did factory data reset
but still the same
any help please ?
Click to expand...
Click to collapse
please update firmware to 14.1.B.0.475 and it should be resolved, and make sure you fully charge to 100%
gromblelord said:
please update firmware to 14.1.B.0.475 and it should be resolved, and make sure you fully charge to 100%
Click to expand...
Click to collapse
+ after update factory reset with wipe !
gromblelord said:
please update firmware to 14.1.B.0.475 and it should be resolved, and make sure you fully charge to 100%
Click to expand...
Click to collapse
yeesss it works:victory:
Related
Here's how to 'hard reset' your TG01!
- Power off device
- Hold down 'volume up' and 'camera' buttons
- Press power button
- Follow on screen prompts
Sorted!
Original thread: Modaco forum
Thank you for the advice.
Thanks for help
Thanks for help
I've followed your instructions and succeeded 100%
Best Regards,
Bassam
how long will the toshiba logo stay?
edit:
ok after hard reset i have to do the short pin method
thanks anyway
fantomel said:
Here's how to 'hard reset' your TG01!
- Power off device
- Hold down 'volume up' and 'camera' buttons
- Press power button
- Follow on screen prompts
Sorted!
Original thread: Modaco forum
Click to expand...
Click to collapse
elder T said:
Thank you for the advice.
Click to expand...
Click to collapse
bassam777 said:
Thanks for help
I've followed your instructions and succeeded 100%
Best Regards,
Bassam
Click to expand...
Click to collapse
DeeJay05 said:
how long will the toshiba logo stay?
edit:
ok after hard reset i have to do the short pin method
thanks anyway
Click to expand...
Click to collapse
What about 'Master Reset' option in settings where you enter you pin i.e. 1234, press 'reset' and it hard resets the phone? :s
drupad2drupad said:
What about 'Master Reset' option in settings where you enter you pin i.e. 1234, press 'reset' and it hard resets the phone? :s
Click to expand...
Click to collapse
This is if you have a unbootable phone that cant get into windows. the only option is to use this method
hi
emergency PLEASE help me
i lost my tg01 boot i cant hard reset and pin flash
olyloh6696 said:
This is if you have a unbootable phone that cant get into windows. the only option is to use this method
Click to expand...
Click to collapse
yea it erase the nand flash like a format and the the drive is real clean and only toshiba logo is displayed
shahryarkh said:
hi
emergency PLEASE help me
i lost my tg01 boot i cant hard reset and pin flash
Click to expand...
Click to collapse
read this:
tg01 two brick variants how to unbrick
and do this:
2 Short-Pin unbrick method
1. Copy a functional ROM on SD Card. PRG folder
2. Rename to TG01WP_00.enc
3. Put the battery in and plug Power- Kable. Charging LED flash RED *
4. short pin 1 and 3 (back side under sim card, remove black plastic) Hold the short and RESET. Hold short pin 1 and 3 for 10 sec. Display go on and ROM flash beginn
* if red led not flash- use TG Downloader unbrick method with user manual in german (pls translate with google translator for other languanges)
contains: TG01 Downloader TG01 Driver TGTool
guys .. need a little help ... i installed tf 3d and when i restarted .. the phone just stands at "starting windows" .. any advice?
edit:
so i tryed to enter boodloader but no success what so ever .. eventually i used short pin method .. oh.. and i must say it was a breath taker ... now the phone works ok ...
warcaller said:
guys .. need a little help ... i installed tf 3d and when i restarted .. the phone just stands at "starting windows" .. any advice?
Click to expand...
Click to collapse
If a soft reset doesn't work then hard reset, hopefully you installed from a fresh rom flash/hard reset anyway?
warcaller said:
guys .. need a little help ... i installed tf 3d and when i restarted .. the phone just stands at "starting windows" .. any advice?
edit:
so i tryed to enter boodloader but no success what so ever .. eventually i used short pin method .. oh.. and i must say it was a breath taker ... now the phone works ok ...
Click to expand...
Click to collapse
tf3d never causes me any of these problems, what ROM were you on?
Thank you
... this saved my Day.
I wasn't able to do a Master Reset after Flashing.
OK, so after trying out the last android build from Markinus, winmo is now saving text messages to the SIM.
If I do a 'hard' reset, what will I lose on my phone? (contacts/texts/email setup etc??). Please explain the downside of hard reseting. Thanks! (or basically.. will I need to save/backup anything before hard resetting?)
Also: Will it remove the 'unlock' that I have applied to my phone?
Update: Well I did it anyway. Saved my contacts, but that's about it lol. Hopefully this will get my messages to saving back into memory rather than onto the sim.
Hello,
Sorry for my bad English, I have a problem with my samsung sII, by mistake I wanted to install a ROM s1 galaxy I did not see that this is the S1 and not S2 Rom
Fortunately, the ROM is not installed and the phone got stuck in the download menu, after 15 minutes I turned off my phone and he wants to turn on , I try to start it in normal mode and download mode but nothing happens
it mean that my phone is dead or it There's a solution?
Thank you in advance
From what i have heard you hard brick your phone if you try to flash i sgs1 rom on a sgs2 phone.
JTAG service should fix it.
I can really recommend this service, very helpful personel:
http://www.mobiletechvideos.com/blog/
Can you get it into download mode with a jig?
Sent from my GT-I9100 using XDA Premium App
I will see that, tnx for your answers gays
bouighil said:
I will see that, tnx for your answers gays
Click to expand...
Click to collapse
HAHAHAHAHA you just made my day. learn english dude you could get in some bad situations
bouighil said:
I will see that, tnx for your answers gays
Click to expand...
Click to collapse
LMAO
I think if you flash a SG1 rom your phone will die.
bouighil said:
I will see that, tnx for your answers gays
Click to expand...
Click to collapse
It's guys not gays
Sent from my GT-I9100 using xda premium
Here we go... Another SGS1 flash on S2.
Bricked.
GG.
Send it back to sammy and tell them u plugged it to ur wall charger and it died.
As mentioned if you flash an SGS 1 ROM w/ Pit to the phone, it will brick it and require JTAG if it won't power up:
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-ii-jtag-brick-repair/
Thanks for the reference guys...I mean gays...
loooool, sorry guys, and tnx for your answers, i hope that JTAG will repair my phone, i miss my Samsung
Try This:
If you think your phone may be bricked and wont turn on, try a soft reset (possibly followed by a hard reset)
1. Take out the battery, then press and hold the ON button for about 10 seconds or so. Replace the battery, then press ON button to try to switch on. This is a soft reset, and wipes the temporary memory and empties all remaining power in the circuits.
2. If this does not work, do as above but after inserting the battery, press and hold the ON+HOME buttons at the same time for 10 seconds or so again. This is a hard reset, and works best if done after a soft reset, so always try the soft reset first.
extract1 said:
Try This:
If you think your phone may be bricked and wont turn on, try a soft reset (possibly followed by a hard reset)
1. Take out the battery, then press and hold the ON button for about 10 seconds or so. Replace the battery, then press ON button to try to switch on. This is a soft reset, and wipes the temporary memory and empties all remaining power in the circuits.
2. If this does not work, do as above but after inserting the battery, press and hold the ON+HOME buttons at the same time for 10 seconds or so again. This is a hard reset, and works best if done after a soft reset, so always try the soft reset first.
Click to expand...
Click to collapse
It doesn't work
bouighil said:
I will see that, tnx for your answers gays
Click to expand...
Click to collapse
Funniest post ever!!!~
s2d4 said:
Funniest post ever!!!~
Click to expand...
Click to collapse
cant stop laughing...poor gay(guy hehe
Sir, please help me with my problem. Have anyone experienced after flashing a rom then the home button long press isn't working? another one is when you are in an app then if you press home button it jist don't get you back to home screen? please help me with this. thank you!
ybrek said:
Sir, please help me with my problem. Have anyone experienced after flashing a rom then the home button long press isn't working? another one is when you are in an app then if you press home button it jist don't get you back to home screen? please help me with this. thank you!
Click to expand...
Click to collapse
Must be the rom with the broken home button...
Which rom are you on? When does this problem occur? Some more info could be helpfull if you want people to help you with your specific problem
Sent from the Matrix
Donnie Sins said:
Must be the rom with the broken home button...
Which rom are you on? When does this problem occur? Some more info could be helpfull if you want people to help you with your specific problem
Sent from the Matrix
Click to expand...
Click to collapse
i'm sorry sir. The rom I used was WanamLite 12.8. After upgrading from 12.7 to 12.8 this problem just appeared. It was just after flashing sir. And another thing ive noticed is that when you long press power button, only shutdown and reboot are present and no flight mode and data connection etc is shown.
ybrek said:
i'm sorry sir. The rom I used was WanamLite 12.8. After upgrading from 12.7 to 12.8 this problem just appeared. It was just after flashing sir. And another thing ive noticed is that when you long press power button, only shutdown and reboot are present and no flight mode and data connection etc is shown.
Click to expand...
Click to collapse
Actually I've never had this problems... I did try both WanamLite versions, but I always do a full wipe so I never face any troubles. Maybe try that after a Nandroid backup?
Sent from the Matrix
Hello All,
I have a problem, a continuous reboot, I make a full format of the device and re-flashing the official rom for many times and the problem still not solved ..
I took it to the agent and told me that matherboard is the problem ..
Then I took it to a phone repair shop, told me that the problem is not in matherboard but I can solve it in another way by flashing rom without Odin or kies ..
Is there another device that specializes in the installation of devices to Roms..
Please help me to solve the problems,
almuhajir said:
Hello All,
I have a problem, a continuous reboot, I make a full format of the device and re-flashing the official rom for many times and the problem still not solved ..
I took it to the agent and told me that matherboard is the problem ..
Then I took it to a phone repair shop, told me that the problem is not in matherboard but I can solve it in another way by flashing rom without Odin or kies ..
Is there another device that specializes in the installation of devices to Roms..
Please help me to solve the problems,
Click to expand...
Click to collapse
maybe it's problem Power button, but do not you think I have seen several cases of restarts and happens to be the powe button, even to me happened, and I thought it was problem of the rom, but I realized that ra Power button . check that, try to clean small espacion and testing.
mojonx0droid said:
maybe it's problem Power button, but do not you think I have seen several cases of restarts and happens to be the powe button, even to me happened, and I thought it was problem of the rom, but I realized that ra Power button . check that, try to clean small espacion and testing.
Click to expand...
Click to collapse
Thanx bro,
I format phone as new clean every thing just only official rom i install with out any applications
almuhajir said:
Thanx bro,
I format phone as new clean every thing just only official rom i install with out any applications
Click to expand...
Click to collapse
ok, but I'm talking about the physical power button, no app
mojonx0droid said:
ok, but I'm talking about the physical power button, no app
Click to expand...
Click to collapse
do you mean i have to change it
almuhajir said:
do you mean i have to change it
Click to expand...
Click to collapse
He is asking u to clean the power button. The interiors of the phone.
Sent from my GT-I9300.
Give a thank if i helped you.
JellyYogurt said:
He is asking u to clean the power button. The interiors of the phone.
Sent from my GT-I9300.
Give a thank if i helped you.
Click to expand...
Click to collapse
Sorry bro,
how can i do it
almuhajir said:
Sorry bro,
how can i do it
Click to expand...
Click to collapse
Dismantle the phone
Sent from my GT-I9300.
Give a thank if i helped you.
hi every one i have problem with my xperia go cm12 5.0.1
some time my phone stuck or freeze and i must make reboot v+ with power button
and when i use whatsapp or some apk at take long time to enter
some time when i wont to open my lock screen nothing showing when i presse power button
so please help me and if some one have idea to speed my xperia go
thx for all
babyshark1983 said:
hi every one i have problem with my xperia go cm12 5.0.1
some time my phone stuck or freeze and i must make reboot v+ with power button
and when i use whatsapp or some apk at take long time to enter
some time when i wont to open my lock screen nothing showing when i presse power button
so please help me and if some one have idea to speed my xperia go
thx for all
Click to expand...
Click to collapse
To know for sure, what exactly is the cause for this all you should look at common problems /bugs in CM development. Secondly posting these questions in specific CM thread in Q/A section can be of more help.
Quote me back if you expect a reply.
Good Luck