Hi everyone,
My S3 stucks on boot logo ,and when i connect it to the charger i have just the grey battery with cirle inside it , no grenn battery after 3 hours.I'd tried several usb cable chargers but nothing. I tried to flash it with odin throught Download mode it always fail after NAND Write Start!! .Even with stock roms or custom ones .and i can't go in recovery mode.
In Odin mode appear like :
PRODUCT NAME :GT-I9300
CUSTOM BINARY DOWNLOAD :YES (7 COUNTS)
SYSTEM STATUT: Custom
Any suggestions Please: tnx:good:
Sounds like nand damage, you can try a rescue firmware & pit:
http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
But I wouldn't hold out too much hope.
Thank you very much, for your reply..
I'll try this night..
Regards
I followed all the instructions and always the same result No Pit partition ,here is the log :
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXDLJ4_368423_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXDLID_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_BTU_I9300OXADLJ4_368423_MULTI_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Any others suggestions PLZ
ID:0/005> There is no PIT partition.
Destroyed PIT requires a service centre paid for repair .
jje
If you added the pit file and ticked repartition then as jje says it needs a new motherboard, sorry.
Related
Hello i need some help recovering a Samsung galaxy S 2 GT-i9100
it is stuck in Boot mode (showing Only the Samsung galaxy s2 logo) soft bricked?
i tryed to fiddel with http://forum.xda-developers.com/showthread.php?t=1449771
but i am unabel to boot into "Download mode " the green dude is only showing for a moment and then it return to the SG logo....
Please advise
You won't be fixing it unless you get into download mode. Keep trying.
Emort said:
Hello i need some help recovering a Samsung galaxy S 2 GT-i9100
it is stuck in Boot mode (showing Only the Samsung galaxy s2 logo) soft bricked?
i tryed to fiddel with http://forum.xda-developers.com/showthread.php?t=1449771
but i am unabel to boot into "Download mode " the green dude is only showing for a moment and then it return to the SG logo....
Please advise
Click to expand...
Click to collapse
go to recovery and do full wipe and then check.
Now in Download mode but..
In odin i keep reciving
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100-CSC-MULTI-OXAKI3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_NEW_BOOTLOADER.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> Sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> zImage
[B]<ID:0/005> Complete(Write) operation failed.[/B]
<OSM> All threads completed. (succeed 0 / failed 1)
Odin Picture:
emort.dk/odin3.png
all usb ports tried on 2 different PC's
3 different cables tried
any ideas?
Find Hopper8's 'Odin troubleshooting' thread & try the stuff in that thread/keep trying. In many cases these things are fixed by perseverance I.E the first 7 flashes dont work but the 8th works for whatever reason. Unless you'd rather take it to a Samsung service centre & explain how you broke it (and pay to have it fixed) ?
Emort said:
In odin i keep reciving
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100-CSC-MULTI-OXAKI3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_NEW_BOOTLOADER.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> Sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> zImage
[B]<ID:0/005> Complete(Write) operation failed.[/B]
<OSM> All threads completed. (succeed 0 / failed 1)
Odin Picture:
emort.dk/odin3.png
all usb ports tried on 2 different PC's
3 different cables tried
any ideas?
Click to expand...
Click to collapse
The same thing happened to me on My Galaxy s1.
Un-install all samsung drivers
Install Samsung KIES
and update drivers in download mode
make sure to kill all kies task from Task manager
Try different Odin version
Try to flash older Version firmware like Ginger bread
...which is exactly what Hopper's thread says (among other things) & was the whole point of him putting that info together - so these things don't have to be regurgitated time & time again for every n00b who gets stuck/asks.
MistahBungle said:
...which is exactly what Hopper's thread says (among other things) & was the whole point of him putting that info together - so these things don't have to be regurgitated time & time again for every n00b who gets stuck/asks.
Click to expand...
Click to collapse
well tried all the possible soluton no luck.
Hi guys!
My i9300 does not boot and instead keeps displaying the samsung logo. It doesn't enter the recovery mode either, but does enter the download mode. So I tried flashing 2 different official ROMs but I'm getting the error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I downloaded the ROM here:
<tried posting a link but was not allowed>
Could you please help me with this problem?
Thanks in advance!
Try another version of odin, different lead, port or pc. Ensure kies is not running. Follow the guide on flashing to the letter.
Download the rom from sammobile and check the md5.
Sent from my GT-I9300 using Tapatalk
wicccked said:
Hi guys!
My i9300 does not boot and instead keeps displaying the samsung logo. It doesn't enter the recovery mode either, but does enter the download mode. So I tried flashing 2 different official ROMs but I'm getting the error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I downloaded the ROM here:
<tried posting a link but was not allowed>
Could you please help me with this problem?
Thanks in advance!
Click to expand...
Click to collapse
I had a similar issue a while ago but it turned out to be an issue with the Kernel not being compatable with the Rom I flashed. I thought I had bricked it, until I flashed a stock kernal first then the stock ROM and it fixed it for me and it really does sound like you have the same issue, As for the rom not flashing its most likely a bad download try sammobile! let me know if it was the kernal!
jaggythistle said:
I had a similar issue a while ago but it turned out to be an issue with the Kernel not being compatable with the Rom I flashed. I thought I had bricked it, until I flashed a stock kernal first then the stock ROM and it fixed it for me and it really does sound like you have the same issue, As for the rom not flashing its most likely a bad download try sammobile! let me know if it was the kernal!
Click to expand...
Click to collapse
jaggythistle, thank you for the answer.
I downloaded the stock kernel, successfully flashed it, downloaded the matching ROM (1-file this time), but now when trying to flash I'm getting the following error:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300UBEMH3_I9300UBEMH1_I9300ECOEMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
What can I do?
boomboomer, Thanks for the reply. I have checked it all, now I'm getting the above error.
If you've tried all the connection issues then it appears your recovery positron is corrupt and can't be written. A rescue firmware, including pit might help but otherwise you'll need a new motherboard.
Search in general forum for the rescue firmware thread, follow the instructions.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
If you've tried all the connection issues then it appears your recovery positron is corrupt and can't be written. A rescue firmware, including pit might help but otherwise you'll need a new motherboard.
Search in general forum for the rescue firmware thread, follow the instructions.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
I have tried the rescue firmware and got the following error:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_I9300OXEEMH1_SER_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
PIT damaged new motherboard .
You can search for this thread where a claim was made to fix pit .
(SOLVED) PIT/Bricked/Dead problem on GT-I9300 international
Worth trying before buying a new motherboard as you have no warranty .
JJEgan said:
PIT damaged new motherboard .
You can search for this thread where a claim was made to fix pit .
(SOLVED) PIT/Bricked/Dead problem on GT-I9300 international
Worth trying before buying a new motherboard as you have no warranty .
Click to expand...
Click to collapse
Tried it, Odin was hanging at the "Erase..." step for ~5-10 mins, then I got the error:
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Erase...
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
hi guys. my i9300 is bricked. I tried to flash roms with odin.
it stucked at samsung gt-i9300 galaxy s3 text. no samsung logo.
Also I can't get in to recovery mode.
When i try to flash any rom (included stock rom) i get this error
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CheckROM_V4_LG8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried many of PIT files. Still the same error.
Sorry for my english
This belongs in q/a
Sent from my GT-I9300 using Tapatalk
Hello,
My wife has this phone and the phone accidentaly turned off and after that he was not able to boot. It was stucked on samsung logo. I tryied recovery mode and wipe phone, but it not helped. After that phone started stucking on galaxy S2 logo (before samsung logo). I was able only to go into download mode. I tried to follow this guide: wccftech.com/install-latest-android-412-jelly-bean-galaxy-s2-i9100-official-firmware but in odin (v3.07) it failed after some time (while progress bar is not moving from beginning, I see only one px of it). And now phone is showing message: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.". Please can you help me how can I recover phone back? thanks a lot for any help
it is czech version bought in samsung shop. So I downloaded XEZ-I9100XWLSD-20130301125313 (but I am not totaly sure about version, this should be for czech)
On load PDA
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLSD_I9100XXLS8_I9100XEZLS1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
After press Start
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> cache.img
After some time
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
dawee said:
Hello,
My wife has this phone and the phone accidentaly turned off and after that he was not able to boot. It was stucked on samsung logo. I tryied recovery mode and wipe phone, but it not helped. After that phone started stucking on galaxy S2 logo (before samsung logo). I was able only to go into download mode. I tried to follow this guide: wccftech.com/install-latest-android-412-jelly-bean-galaxy-s2-i9100-official-firmware but in odin (v3.07) it failed after some time (while progress bar is not moving from beginning, I see only one px of it). And now phone is showing message: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.". Please can you help me how can I recover phone back? thanks a lot for any help
it is czech version bought in samsung shop. So I downloaded XEZ-I9100XWLSD-20130301125313 (but I am not totaly sure about version, this should be for czech)
On load PDA
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XWLSD_I9100XXLS8_I9100XEZLS1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
After press Start
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> boot.bin
<ID:0/009> NAND Write Start!!
<ID:0/009> cache.img
After some time
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Seems like you have brick bug but I have no idea how to fix it.
Next I have tried to follow this guide: http://forum.xda-developers.com/galaxy-s2/help/guide-fix-unflashable-soft-bricked-gsii-t1457458
I am not totaly sure about kernel version, but because this phone was pursached on his release, I have downloaded GINGERBREAD VERSION. I have tried to flash it but without success too. Green progress bar is moving to the end and after some time it writes "fail"
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Kernel_I9100XXKI3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> zImage
<ID:0/010> NAND Write Start!!
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm currently having "Kernel is not Seandroid enforcing" error message.
First, I rooted my phone, then preparing into flashing a custom ROM and kernel.
I downloaded Extended battery (v 2.91.45) - N910C/H for Kernel and Nemesis for ROM.
Wipe cache and etc then flash the kernel via TWRP first while I was downloading the Custom ROM.
Rebooted after I flashed the Kernel (maybe I screwed up here because I don't have any ROM installed yet?)
Phone couldn't go anywhere past the boot screen which shown "Kernel is not Seandroid enforcing" error message.
After searching the internet, people suggested to flash the stock ROM via ODIN, but then I have these errors on Odin 3 v3.04
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910GDTU1COJ5_N910GOLB1COJ1_N910GDTU1COJ4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
And no response on Odin3 v3.12
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1205)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
I'm flashing with the latest stock ROM in my Country.
Tried different USB ports
Tried different USB cables.
Tried factory reset/ manual wipes
OS : 6.0.1
Model : SM-N910C - Samsung Note 4
What else can I do on my end before sending it to shops ?