Hey guys,
i think i bricked my phone.
i must admit it may be my own fault as i didnt really know what i was doing anyways ill talk you through what happened....
i was trying to get cwn recovery onto my phone and as said i was unsure of what i was doing (i know im Stupid) i had already sucessfully rooted the phone and i opened mtkdroid tools and clicked backup and recovery the box on the right started to spit out text as my phone became detached from the data cable.
Now when i try to power up the phone the backlight lights up for 3-4 seconds then nothing if i hold
volume + and power with no data cable i get the same backlight for 3-4 seconds
volume + and power with data cable i get a dead droid with a red ! in a triangle in its belly ?
the phone displays a battry bar in blue if i do nothing
the pc seems to recognise phone as universal serial bus
mtkdroidtools does not regognise the phone at all
the phone did say android preloader driver not found but ive installed this and this has now disapeared?
anyone help even if its just to tell me to give up (hopefully not ive had the phone about 2 hours EPIC FAIL)
bump
Over 90 views and no-one even attempted to help...
Short and sweet , hopefully this will get you up and running again.
Download these 2 files
http://pan.baidu.com/share/link?uk=3055194073&shareid=4221153774[/URL
[URL="http://d-h.st/KyK"]http://d-h.st/KyK
Basically this is the default rom, along with spflashtools.
Unzip both to your harddrive somewhere.
Open the location you have extracted spflashtools and click on Flash_tool.exe , then, click scatter-loading on the right hand side, and point it to where you have extracted the rom.
Now, with your phone unplugged from PC/Laptop click the Download button in SPFlashtool. Click ok to anything that pops up.
Now, take the battery out of your phone, and insert the usb cable into the laptop, WITH BATTERY UNPLUGGED . Keep the battery unplugged untill the flash is complete, a little box with a circle saying OK will show after few minutes.
Try this, hopefully this will put you back to stock and you can try again
Cheers pal ill give this a try tomorrow. You're a legend!
And to the 90 views I don't mind as said its my own fault and can't blame the people who had ideas bet they get this all the time usually from noobs who require babysitting through the process ...
Anyways fingers crossed
Ok so its not working im getting the error in the following picture if anyone can help......
firstly sp flash tools just searches for the com port / usb when the battery is not installed ive tried various build of sp flash with the same results.
when i insert the battery it finds com 5 or 6 and goes to 100% of the red progress bar then i recieve the following error
heres a screenshot (icant post links yet)
imageshack.us/photo/my-images/268/lrid.jpg/
many thanks
Garry
BIGG1985 said:
imageshack.us/photo/my-images/268/lrid.jpg/
Click to expand...
Click to collapse
Have you a link to where you bought your phone ?
Looks like a dual core version ?
If you can point me to where you purchased your model i should be able to get you the correct ROM to load
unfortunatly the phone was bought from a guy in england looks like he ripped me off.... it appears to be the same phone as
dhgate.com/product/air-gesture-real-5-0-inch-s4-1-1-i9500-7/139991313.html#s1-2-1|3289411982
what about it only working with the battery in too is this a big problem i make sure the phone is still not powered on but it just wont download with the battery out....
many thanks
Garry
soft brick
BIGG1985 said:
Hey guys,
i think i bricked my phone.
i must admit it may be my own fault as i didnt really know what i was doing anyways ill talk you through what happened....
i was trying to get cwn recovery onto my phone and as said i was unsure of what i was doing (i know im Stupid) i had already sucessfully rooted the phone and i opened mtkdroid tools and clicked backup and recovery the box on the right started to spit out text as my phone became detached from the data cable.
Now when i try to power up the phone the backlight lights up for 3-4 seconds then nothing if i hold
volume + and power with no data cable i get the same backlight for 3-4 seconds
volume + and power with data cable i get a dead droid with a red ! in a triangle in its belly ?
the phone displays a battry bar in blue if i do nothing
the pc seems to recognise phone as universal serial bus
mtkdroidtools does not regognise the phone at all
the phone did say android preloader driver not found but ive installed this and this has now disapeared?
anyone help even if its just to tell me to give up (hopefully not ive had the phone about 2 hours EPIC FAIL)
Click to expand...
Click to collapse
it is soft brick you should flash with boot image!!
BIGG1985 said:
unfortunatly the phone was bought from a guy in england looks like he ripped me off.... it appears to be the same phone as
dhgate.com/product/air-gesture-real-5-0-inch-s4-1-1-i9500-7/139991313.html#s1-2-1|3289411982
what about it only working with the battery in too is this a big problem i make sure the phone is still not powered on but it just wont download with the battery out....
many thanks
Garry
Click to expand...
Click to collapse
ok
Try downloading this rom
http://www.needrom.com/wp-content/uploads/2013/08/S4-6577_AIRGESTURE_I950X_V101En20130627.rar
You may to need to register with needrom
That ROM is the default MTK6577 Rom with air gestures
Do as i instructed earlier, extract the rom from zip, this time rename the folder as it contains special characters which may throw of SP Tools
i.e rename folder S4จาง6577_AIRGESTURE_I950X_V101En20130627 to mtk6577 or something.
Then load the scatter file, hit download and insert cable again with no battery , see if that runs now
also , here are the MTK6577 drivers if required
http://androidurdu.com/download/MT6577%20USB%20VCOM%20drivers.rar
Ok so.......
again nothing without the battery installed just keeps searching and nothing.
witht the battery in it flashed got the green circle and everything.
but when i power up the phone i get a white display with black lines down centre.... occasional color bit
same screen when i try to enter recovery
meh not got my hopes up aswell
thnaks for the help guys really appreciate
is it worth trying to flash anything else or should i give up.....
OK don't panic.
First you should know there's plenty of S4 clones out there (HDC Galaxy S4, HDC Spark, Meso S4, unidentified Dual SIM S4 clone, etc., etc.).
Second you have to be 100% sure your system is properly set up.
If you or a friend of you has another MTK (better if MTK6589) smartphone check if everything works properly (drivers, flashing, etc.).
If not install everything properly and in a clean Windows partition without 300 USB drivers and devices.
Once you are done with what written above come back and we will see.
In the meantime upload a pic of the backside without cover and battery, but please be sure to hide the printed IMEI number.
Sent from my Samsung Galaxy Note with Tapatalk 2
Thanks i will have to look into creating a windows partition not something i have ever done.. i will also get a picture of the phone uploaded asap thanks for your help.i dont have a friend with a similar phone but i do have an mtk6589 s4 coming from china (dhgate) its a replacement for one that was broke on arrival just takes forever i bought this to put me on..
Hey guys here are the pictures on the phone
imageshack.us/a/img20/8845/kss4.jpg
imageshack.us/a/img829/25/yskl.jpg
imageshack.us/a/img12/5650/jgij.jpg
imageshack.us/a/img823/1478/7b2o.jpg
i also took a screen shot from USB Deview to show what drivers are being used during a flash not sure if its useful or not tho.
thanks again
Garry
So youvr bought a take s4 and fvcked it... good one you n0000b
Sent from my GT-I9300 using xda premium
cheadabudas - yes i maybe a n00b but at least im not someone who has nothing better to do than troll through xda commenting on posts with no relevance L0S3R :laugh:
After speaking to the original owner i believe this is the phone.....
dhgate.com/product/new-arrive-1-1-gt-i9500-i9500-feiteng-h9500/164699915.html#s1-2-1|2177543576
it also has the same black block near the speaker jack which i havent noticed on any other model
anyone have a rom ?
Bump
ok so finally found the required rom for anyone else having the same problem
http://www.filedropper.com/1to1s4softwareandtool
broken link
BIGG1985 said:
ok so finally found the required rom for anyone else having the same problem
your link does not work anymore can you send a working link, thanks.
Click to expand...
Click to collapse
Trojan found in USB driver from package in the androidurdu.net
wilsey said:
ok
Try downloading this rom
needrom.com/wp-content/uploads/2013/08/S4-6577_AIRGESTURE_I950X_V101En20130627.rar
You may to need to register with needrom
That ROM is the default MTK6577 Rom with air gestures
Do as i instructed earlier, extract the rom from zip, this time rename the folder as it contains special characters which may throw of SP Tools
i.e rename folder S4จาง6577_AIRGESTURE_I950X_V101En20130627 to mtk6577 or something.
Then load the scatter file, hit download and insert cable again with no battery , see if that runs now
also , here are the MTK6577 drivers if required
androidurdu.com/download/MT6577%20USB%20VCOM%20drivers.rar
Click to expand...
Click to collapse
Beware of Win.Trojan.Slugin-283
was deteced by antivirus from this site.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Related
I upgraded my Neo to 2.3.4 from pccompanion for test it, then downgraded to 2.3.2 to enable root and my battery shows 0% charge. It refuses to charge showing always a red light on led. Reflashing to 2.3.4 doesn't resolve problem. Reflashing 2.3.2 and rooting to delete batterystats.bin doesn't resolve the problem.
I tried everything, remove battery, cleaning it, charging via pc usb, via wall socket all night...
I see in Arc forums more people with this problem.
First rule of safety. Don't trust some ftf(or any software for that matter) files put up from china. There are more expert hackers there than you can imagine. Anything might have some little "bonus" code along the normal stuff(doing nothing in your interest), which may break some normal functioning as well. Blind faith and trust will get your stuff broken sooner or later. IF the ftf is in any way tampered it will not work well with your locked bootloader, things can and will break. Use Wotanserver, it's safer but even then... you're not 100% safe.
You tried relocking bootloader and repairing via SEUS?
Get 2.3.3 via Wotanserver before if necessary.
remove the battery from phone and reconnect.
My bootloader is locked. I always used wotanserver to downgrade, so no chinese ftf used. And tried upgrading, downgrading and repairing via SEUS and problem persists.
I removed battery and reconnected dozens of times.
Seems that in Arc forum are more people with same problem.
Ok do you know that you can start phone without battery? I can't immediately find the thread here in XDA. One method was in Motorola Defy forums, using spare USB cable to connect it to phone - and + battery connectors. For other you need some battery juice to get to second bootimage.
Had my defy go into similar state after USB connection failed during upgrade to official froyo... It was deader than dead. Sent it back to shop for repairs.
If you can get another battery you could try if your phone is discovered in SETool and if not then on this thread you can find help to fix bootloader http://forum.xda-developers.com/showthread.php?t=1254409.
To use it you still need a charged battery, so get yours charged or get new.
Did you watch btw how much battery you had left before flashing? Flashing may fail in mid process if it goes below 40%.
Hi Elessar, I suggest you to send your phone to SE if you still have your warranty. I had the same problem and SE replaced a new motherboard for my NEO. I saw this issue on a couple of forums and there is no solution yet.
And Raoa, I do understand your concerns, but I think you have worried too much. Most ftf files that I can find on Chinese forums are mirrored from XDA as well as flashing tools, etc. If the Chinese really want your phone hacked, it has already been hacked anyways, because your phone is probably made in China or part of some part of your phone is made in China.
flash any stock FTF
DO NOT power on device
now directly connect to charger (usb or wall charger) for a few hours [make sure that the offline-charging "animation" is seen on screen]
the battery stats will get refreshed
DooMLoRD said:
flash any stock FTF
DO NOT power on device
now directly connect to charger (usb or wall charger) for a few hours [make sure that the offline-charging "animation" is seen on screen]
the battery stats will get refreshed
Click to expand...
Click to collapse
flashed the stock ROM
did not power on the device.
directly connected to the wall charger....
but the device powered on automatically and the battery still at 0%..
PLEASE HELP!!!!!! I DONT EVEN HAVE THE WARRANTY NOW....
Your logic is incomplete yunle. It's the other way around, a very eager ftf providing comes from China, and these files get mirrored on US/EU servers not the opposite way. Official phone making is not the same as "enthusiastic" providing of unofficial flashing files. 3rdly, trust or not, but always check what is what. Worry and think whatever, thinking can always be wrong. I rather trust an European who puts the source of SE files up along with user made ftf file. Saying anything else is suggesting to "flash away and don't think, all will be fine, nothing bad will happen".
Anyone with this battery problem have you tried relocking bootloader and fixing via SEUS? Try it, if you haven't. It worked for someone in a simliar situation.
My bootloader is locked by Vodafone and tried to refix with SEUS 3 times, no luck.
DooMLoRD said:
flash any stock FTF
DO NOT power on device
now directly connect to charger (usb or wall charger) for a few hours [make sure that the offline-charging "animation" is seen on screen]
the battery stats will get refreshed
Click to expand...
Click to collapse
Can anybody confirm that this works, I tried it but as soon as I connect to wall charger the phone auto start!!
Please DooMLoRD Help...
No, phone autostarts for me too.
My arc got this problem too.can anyone tell me which way to get it back normal???
I tried,doesn't work。 Plug in the charger and phone starts
Can someone try this modification of DooMLoRD's advice:
1. flash any stock FTF
2. DO NOT power on device
3. now press back button without release it and directly connect to charger (usb or wall charger) for a few hours [make sure that the offline-charging "animation" is seen on screen] and test if led is green or orange. If it's red, it doesn't work.
4. If it's not red, you can release back button and wait a few hours charging and reboot your phone.
regards
my arc show green
heidality said:
my arc show green
Click to expand...
Click to collapse
Really?
My Neo don't show green LED....
Same issue happened with me also
Hey man,,
I do have same problem after flashing 2.3.2 kernel from wotanserver for rooting my Xperia Neo mobile.
I tried everything all night charging... and reflashing latest update from SE PC suite.
Same issue persists..
Tomorrow I am going to contact SE service people.
Regards,
Bhanu Chaitanya
Hyderabad,
India
Hello, sorry for my english.
Can you guys try this method:
There is a simple reset button at the back of the phone.
Firstly remove the hull, then see that images:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
remove the plastic mask
Then press the button.
I hope that could help you
NeoJeo said:
Hello, sorry for my english.
Can you guys try this method:
There is a simple reset button at the back of the phone.
Firstly remove the hull, then see that images:
remove the plastic mask
Then press the button.
I hope that could help you
Click to expand...
Click to collapse
Are you sure it is BUTTON, not plug for ANTENNA....?
alright..
i've read possibly 5 or 6 threads from start to end, post by post last week..
some people faced similiar problems but none of them faced exactly the same..
only one guy did, but i don't know if he could solve it or not..
i'm trying to install Wolf's gingerbread ROM but i have a problem on flashing..
i've downloaded all the files in this topic and followed all the directions there correctly..
i have installed SEMC Flash Drivers..
tried different USB ports..
but i keep receiving this error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
anyone faced the same problem before or can help about solving it?
*
edit:
here is a similiar thread but i get the error sooner..
**
edit:
this either didn't work..
the green led never turn on, until i put the battery back in..
***
edit:
can this be the problem:
in the tutorial's pictures "Firmware Content" frame shows the included .sin file
****
edit:
I solved the problem with a very wierd way.
Hope it helps when you try.
After you've extracted and installed Flashtool;
go to your computer's Control Panel.
Open "Clock, Language and Region".
Click "Region and Language".
Choose format as English (United Kingdom); and location as United States.
Click ok and close control panel.
Now you shold be able to see loader.sin and kernel.sin files inside "Firmware Content" frame when you open Flashtool.
Same error to me...I try everything, every tool that I found for X10 but nothing help it...I also try wotan server with several different firmwares but always same error...ERROR: file header write failed!
I think that is imposible to repair without some dongle like setool...
i try to help...
1.first root ur stock rom n install xrecovery....
2.backup stock rom using xrecovery..
3.wipe data, wipe cache, n wipe dalvik cache using xrecovery...
4. install wolfbreak rom using "XRECOVERY".. When finish, put out the battery
5.lastly install the 2.3.3 n .71 baseband using flashtool....
phobias1903 said:
edit:
can this be the problem:
in the tutorial's pictures "Firmware Content" frame shows the included .sin file
Click to expand...
Click to collapse
wtf dude, you are missing some files there!??! "loader.sin & kernel.sin" ... try re-downloading the flashtool from that thread (http://forum.xda-developers.com/showthread.php?t=1196808)
cikgu senaman said:
1.first root ur stock rom n install xrecovery....
Click to expand...
Click to collapse
man, thats the point where we have problem..
slikk76 said:
wtf dude, you are missing some files there!??! "loader.sin & kernel.sin" ... try re-downloading the flashtool from that thread (http://forum.xda-developers.com/showthread.php?t=1196808)
Click to expand...
Click to collapse
i have downloaded them but i'll try again..
Hey I've had the same exact problem for about 3 months now I've tried everything i can think of.
i even made a battery charger from a usb cord to make sure it wasn't the battery being dead...
D:
any news?
I was having the EXACT same issue that led me to this thread. I had a custom kernal loaded so not sure if that was why I was getting "error flash aborted". Anyhow as someone mentioned here, I held down the back button until the entire flash was completed. That finally worked. Thanks!
One2many said:
I was having the EXACT same issue that led me to this thread. I had a custom kernal loaded so not sure if that was why I was getting "error flash aborted". Anyhow as someone mentioned here, I held down the back button until the entire flash was completed. That finally worked. Thanks!
Click to expand...
Click to collapse
I've had this issue for about a month, I'll try your method when i get home
I had come to the conclusion it was some kind of NAND deterioration
AusX10 said:
I've had this issue for about a month, I'll try your method when i get home
I had come to the conclusion it was some kind of NAND deterioration
Click to expand...
Click to collapse
hi! have you somehow restored your x10 back to life?
if it is NAND problem, have someone found a way to repair/replace it?
necrohades said:
hi! have you somehow restored your x10 back to life?
if it is NAND problem, have someone found a way to repair/replace it?
Click to expand...
Click to collapse
Nope sorry mate I have two devices, that's why i assume its hardware failure because they were both flashed the same way and my primary one is fine (running FXP45)
The bricked X10 is actually from a much newer batch which is odd, you would think the first one to die would be the one i have been flashing roms on since i debranded my 1.6 rom!
The phone is beyond my help now i think because its not even getting into flash mode and neither SEUS or flashtool can see it. It slowly got worse and worse until it wouldn't do anything at all.
I have been using Wolf's tweaked GB ROM for ten days.
I solved the problem with a very wierd way.
Hope it helps when you try.
After you've extracted and installed Flashtool;
go to your computer's Control Panel.
Open "Clock, Language and Region".
Click "Region and Language".
Choose format as English (United Kingdom); and location as United States.
Click ok and close control panel.
Now you shold be able to see loader.sin and kernel.sin files inside "Firmware Content" frame when you open Flashtool.
X10 failure in flashing ROM
I experienced a very hard situation after an unsuccessful ROM flashing onto my x10. Flashing procession was nearly finished but error message was happened and then aborted! Since that my device was permanently unbootable at all, when press the switch button to turn it on, there was no vibration nor SE boot up logo, just a red light brinked up for a few seconds. It seemed to be permanently dead. I tried many ways to reflash ROM onto the device via SE PC Companion, SESU, FlashTool but the program couldn't detect the device nor wiring on flash mode.
The device could not be accessed at all. Is there any experts who can solve this problems, please show me and the other owners how to fix X10 in this matter upon the software; programs, and the obvious procession. That would be greatly appreciated.
tommyboy_bkk said:
I experienced a very hard situation after an unsuccessful ROM flashing onto my x10. Flashing procession was nearly finished but error message was happened and then aborted! Since that my device was permanently unbootable at all, when press the switch button to turn it on, there was no vibration nor SE boot up logo, just a red light brinked up for a few seconds. It seemed to be permanently dead. I tried many ways to reflash ROM onto the device via SE PC Companion, SESU, FlashTool but the program couldn't detect the device nor wiring on flash mode.
The device could not be accessed at all. Is there any experts who can solve this problems, please show me and the other owners how to fix X10 in this matter upon the software; programs, and the obvious procession. That would be greatly appreciated.
Click to expand...
Click to collapse
blinking red you say?
try to charge your battery first, probably using a desktop charger, or another fully charged battery, and re-do flashing through either SEUS or repair thru PCCompanion.
blinking red led indicates battery power too low to boot.
if that fails, i'm afraid you have to try and see a tech
phobias1903 said:
After you've extracted and installed Flashtool;
go to your computer's Control Panel.
Open "Clock, Language and Region".
Click "Region and Language".
Choose format as English (United Kingdom); and location as United States.
Click ok and close control panel.
Click to expand...
Click to collapse
I was able to flash back to stock generic firmware 2.0.A.0.504 using this, not sure if this was the fix or coincidental. Using X10 Flash tool 0.5.3.0.
From there I have flashed the correct BB, Doom kernel for unlocked and recovery yadda yadda. The phone lives (for now...)
Im new to rooting and such, I was trying to gingerbread using odin and it said failed. The phone froze up and I had to pop the battery and now it is dead. is there a way to fix this and get the phone back on? will not go into recover or download modes.
thank you
bump for help thanks
oAnthonYo said:
bump for help thanks
Click to expand...
Click to collapse
Lol...don't expect to get an immediate response from someone. What you need to do is quite being lazy and do some quick research in the the Q & A section.
http://forum.xda-developers.com/showthread.php?t=849028
Now what exactly was it you were flashing? What GB rom did you flash? and was it a .tar file that you flashed along with the 512.pit file?
You should try removing your battery/simcard/sdcard and then try getting into download mode. Don't worry if the yellow android dude doesnt appear. As long as the screen shows some kind of error with a picture of a phone with an (!) mark well then you are good to go. Your PC should still be able to recognize your device. Try different USB ports. Just flash back to stock 2.1 using the guide above if you are able to get into download mode.
thank you, i did some reading and i think i need a jig to get back into dl mode. have tried a lot of different ways to get into dl mode before posting this. thanks for your advice. appreciated.
oAnthonYo said:
thank you, i did some reading and i think i need a jig to get back into dl mode. have tried a lot of different ways to get into dl mode before posting this. thanks for your advice. appreciated.
Click to expand...
Click to collapse
Here is the guide i meant to post. This guide will probably get your phone to boot.
http://forum.xda-developers.com/showthread.php?t=848737
Do you get any power at all? If so then that is a good sign.
Pull your battery and plug in your USB to your computer and open Odin. Do not have your phone attached to the USB yet. Now with Odin open and your battery pulled, (this part is tricky) Hold the Volume +/- and put your battery in and plug your phone in. You do not need to see the Android with the shovel to be in download mode. What you need to see is that yellow COM box in Odin. Once you see that then you are good to go.***See below
Few things:
It may take you a few tries to do this.
If you are not getting any power at all, you may have corrupted your bootloader when you prematurely stopped the install the first time. If this is the case, then sorry to say, but you are screwed and have hard bricked your phone.
Merio- Take it easy on the guy, he is in full blown panic mode and we have all been there. Remember when you got the Encryption Bug?
This is fromN00b_IN_N33D's MIUI guide but it'll serve our purposes here.
"SOFT" BRICKED WHILE USING ODIN?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you are getting a "Phone.. ! ..Computer" image (seen above) when booting phone, yes, you are bricked but it is reversible! Just follow these steps...
Make sure you have ODIN OPEN with admin privileges!
1.) Take off your back cover, remove your sim & mirco sd card.
2.) Remove your battery.
Make sure you have the USB plugged into your PC but NOT your phone!
3.) Hold the volume buttons.
4.) Put the battery in.
5.) Put the USB in.
You don't necessarily need the download mode image to be present. As long as you are getting the COM ID to light up yellow in ODIN, just flash back to stock like normal.
Click to expand...
Click to collapse
Woodrube said:
Do you get any power at all? If so then that is a good sign.
Pull your battery and plug in your USB to your computer and open Odin. Do not have your phone attached to the USB yet. Now with Odin open and your battery pulled, (this part is tricky) Hold the Volume +/- and put your battery in and plug your phone in. You do not need to see the Android with the shovel to be in download mode. What you need to see is that yellow COM box in Odin. Once you see that then you are good to go.***See below
Few things:
It may take you a few tries to do this.
If you are not getting any power at all, you may have corrupted your bootloader when you prematurely stopped the install the first time. If this is the case, then sorry to say, but you are screwed and have hard bricked your phone.
Merio- Take it easy on the guy, he is in full blown panic mode and we have all been there. Remember when you got the Encryption Bug?
This is fromN00b_IN_N33D's MIUI guide but it'll serve our purposes here.
Click to expand...
Click to collapse
Lol, man have I seen that a few times as long aa you can sew something I've always been able to vet it back
Sent from my SGH-T959 using xda premium
I have not been able to get any power as of yet. Think it is hard bricked with what I have read. Thank you ,I will try these things when I get home from work today.
Tried this when I had gotten home and still nothing. It must be hard bricked, can it be fixed with a jig or something else or do I sell it on ebay and buy another one?
oAnthonYo said:
I have not been able to get any power as of yet. Think it is hard bricked with what I have read. Thank you ,I will try these things when I get home from work today.
Tried this when I had gotten home and still nothing. It must be hard bricked, can it be fixed with a jig or something else or do I sell it on ebay and buy another one?
Click to expand...
Click to collapse
Thanks for the help.
You could try to Jtag it (mobilcity something-use the search in Q&A or General and it shoudl pop up). Not sure about selling it on Ebay as you'll have to disclose it as bricked. Once you get a new one, come'on back and we'll take care of you.
Woodrube said:
You could try to Jtag it (mobilcity something-use the search in Q&A or General and it shoudl pop up). Not sure about selling it on Ebay as you'll have to disclose it as bricked. Once you get a new one, come'on back and we'll take care of you.
Click to expand...
Click to collapse
Thank you, I will be around on here. Not going anywhere. Appreciate the advice.
OP I was in your same boat last week. I sent mine to josh at mobile videos.com and for $80 has my phone working again and my custom ROM and kernel installed..I would definitely recommend this because it's a lot cheaper than buying another vibrant online and it takes a week
cpg1987 said:
OP I was in your same boat last week. I sent mine to josh at mobile videos.com and for $80 has my phone working again and my custom ROM and kernel installed..I would definitely recommend this because it's a lot cheaper than buying another vibrant online and it takes a week
Click to expand...
Click to collapse
Thanks Brother,
I was researching places last night and found this same site. I will be shipping it off this weekend to be jtaged. I am glad that they fixed yours.
I was also looking on ebay for galaxy s and sII. I found a listing that a guy had just posted for a sII. He wanted $280 for it which I thought was a steal, I went to take a shower and think about it and when I came back 10 minutes later it was sold. AI missed it.
I recently rooted my phone. Was going good until I softbricked it by editing 1 build prop setting. WARNING: Sprint users, I highly recommend you not modify build prop settings after rooting. Anyway I can get into download, recovery, and factory reset, but none of it works. I have tried almost everything, lg flashtool 1.8 works till 93%, phone reboots, Flashtool then says usb open port fail. factory reset fails. Can't try newer flashtool 2014, because of no kdz file. If there is away to convert .tot to kdz any help would be greatly appreciated. Attached is the blue screen that comes up.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
joeyhdownsouth said:
I recently rooted my phone. Was going good until I softbricked it by editing 1 build prop setting. WARNING: Sprint users, I highly recommend you not modify build prop settings after rooting. Anyway I can get into download, recovery, and factory reset, but none of it works. I have tried almost everything, lg flashtool 1.8 works till 93%, phone reboots, Flashtool then says usb open port fail. factory reset fails. Can't try newer flashtool 2014, because of no kdz file. If there is away to convert .tot to kdz any help would be greatly appreciated. Attached is the blue screen that comes up.View attachment 2902177
Click to expand...
Click to collapse
Damn.. I have been messing with a lot of setting. I better watch out.. Hope u find a solution soon
garynsa said:
Damn.. I have been messing with a lot of setting. I better watch out.. Hope u find a solution soon
Click to expand...
Click to collapse
Yeah it sucks, back to my trusty gs3. Till I can figure how to convert a tot file for use in flashtool 2014, or send it off I assume.[emoji24]
joeyhdownsouth said:
Yeah it sucks, back to my trusty gs3. Till I can figure how to convert a tot file for use in flashtool 2014, or send it off I assume.[emoji24]
Click to expand...
Click to collapse
See if this guy can help
http://forum.xda-developers.com/showpost.php?p=54893808&postcount=74
also u can try this (PLEASE OD THESE AT OWN RISK AS I AM NOT A DEV AND NOT TRIED THIS BEFORE)
http://www.lg-phones.org/how-to-convert-lg-firmware-from-bin-tot-to-kdz.html
garynsa said:
See if this guy can help
http://forum.xda-developers.com/showpost.php?p=54893808&postcount=74
also u can try this (PLEASE OD THESE AT OWN RISK AS I AM NOT A DEV AND NOT TRIED THIS BEFORE)
http://www.lg-phones.org/how-to-convert-lg-firmware-from-bin-tot-to-kdz.html
Click to expand...
Click to collapse
thanks, haven't looked in other variant threads, just contacted him.
gonna see if my Flashtool is the most up to date version after work today. I would like to solve this issue, seems to be in almost every G3 forum. Haven't tried LG suite either.
I think I have the solution, gonna test it out after work today before I mark this thread solved. Will post solution also.
Great
---------- Post added at 10:00 PM ---------- Previous post was at 09:59 PM ----------
I can then try to play eith some settings
garynsa said:
Great
---------- Post added at 10:00 PM ---------- Previous post was at 09:59 PM ----------
I can then try to play eith some settings
Click to expand...
Click to collapse
I know what I did. forgot to set permissions. [emoji35] Guess I'm too used to Samsung.
Set permissions to what?
Yes I did. in LG Flash Tool use Board DL not the other. It worked perfect it boots into normal MiniOS and then you hold Power and push Normal Boot on the screen.
garynsa said:
Set permissions to what?
Click to expand...
Click to collapse
After I rooted I went and changed build prop line for all apps in multiwindow, didnt fix any permissions. When I rebooted phone, got the error. Just fixed it with flashtool finally.
blmvxer said:
Yes I did. in LG Flash Tool use Board DL not the other. It worked perfect it boots into normal MiniOS and then you hold Power and push Normal Boot on the screen.
Click to expand...
Click to collapse
The guide I was following said nothing about changing action to board dl. I wasted 6 hours last night thinking it was never gonna happen. I got it back up.
the resolution to flashtool hanging at 93%, then rebooting to same blue "factory reset status 2" screen is in the attached picture in the left bottom corner. Make sure you change action mode to board DL, this caused me alot of headaches last night. Thanks to user thinh182009 for pointing out this minor lil troublemaker and allowing me to use his image.
joeyhdownsouth said:
the resolution to flashtool hanging at 93%, then rebooting to same blue "factory reset status 2" screen is in the attached picture in the left bottom corner. Make sure you change action mode to board DL, this caused me alot of headaches last night. Thanks to user thinh182009 for pointing out this minor lil troublemaker and allowing me to use his image.
Click to expand...
Click to collapse
PLEASE HELP: i got the same problem and checking board dl didnt work for me im still stuck on 94% and on the red giant number 2
BeamBurrito said:
PLEASE HELP: i got the same problem and checking board dl didnt work for me im still stuck on 94% and on the red giant number 2
Click to expand...
Click to collapse
It took a few times of trying, before it actually worked. A few things to try, redownload .tot file, try different usb cables, or even a different computer. Where did you get .tot from?
Also read THIS guide, very well written.
sent from my LG G3
Don't know if this works for everyone but it worked for me. Ok well i kept getting the blue screen and it wouldnt let me enter recovery mode or do anything it seemed like my phone was over heated the whole time and wouldnt cool down so i stuck my lg g3 without the battery in the fridge for like 15 minutes took it out then put the battery in and it worked!! but it only works for a certain amount of time until it starts to heat back up but maybe that will give you enough time, like it did me, to download all your files onto an sd card or maybe just to your computer and factory reset it. Hope this helps! It worked for me
SOLVED
I had the blue blue screen problem two weeks after the replacement of my broken screen in a LG G3 D855.
It get hot and the battery went down very quick.
I saw this video
ube com/watch?v=6IVFA_224Aw&t=236s
and realiced that the motherboard didn't seat perfectly in its place, so the conectors could make a shor circuit.
putting plastic and paper over de connectors and PROBLEM SOLVED. No blue screen, battery and phone working perfectly.
Regards.
Hi guys, so yesterday i was trying to re-root my Galaxy S3 after applying the firmware update from Kies (4.2.2 to 4.3), so i opened odin 3.10.6 that i downloaded with the root file, opened it, clicked on AP and gave it "CF-Auto-Root-d2att-d2uc-samsungsghi747.tar.md5" then hit start, i think it was installing till it got to like 25% and then got stuck, i ket it there and went to see other videos, so i thought probably i installed it on the wrong way, nothing happened yet on odin so i closed it, and this is how everything started, after about 10hours of trying to fix this, i eventually used Kies to apply "Firmware upgrade and initialization", everything went fine, but after the auto-reboot, the phone gave me this error:
E:failed to mount /system (Invalid argument) can't mount '/system '(Invalid argument)
a long list of it, it couldn't mount like anything at all, i tried to boot the phone and nothing happens, eventuually i learned that the only way to get a response from the phone is by plugging it into the computer and going to Download mode (if it's not plugged nothing happens no matter what i do)
I tried rebooting using the download mode and pressing volume down to reboot, and it actually tries to reboot, and shows the samsung s3 logo followed by an android robot like it's applying some updates but shuts down when it reaches like 40% of the process. here's what happens and please note that it only works if the phones is plugged to the computer, if not, i won't get any response from it no matter what buttons i press, and even when it's plugged that's the only way to get a response.
and by the way, i think it can be a battery problem but i have two battries and the samething happened with both of them, and i kept the phone plugged on the charger the whole night hoping it can be charged but nothing happened, (even while plugging it the red right didn't turn on and the phone didn't respond at all)
so, basically, what i "think" i need now is an appropriate list of all Odin files for samsung s3 so i can revive it ( bootloader, PDA, Phone, CSC, and even UMS if necessary) please if anyone can provide me with these files i'd be very grateful. thanks
If you have access to dowload mode, I suggest you to try part 4 of this guide : http://forum.xda-developers.com/galaxy-s3/general/fix-s3-to-factory-unroot-stock-recovery-t2323847
olimar7184 said:
If you have access to dowload mode, I suggest you to try part 4 of this guide : http://forum.xda-developers.com/galaxy-s3/general/fix-s3-to-factory-unroot-stock-recovery-t2323847
Click to expand...
Click to collapse
thanks for the reply, i did already, but i guess i'll go ahead and try it again.
#update: Yup, the same problem, the little Android robot appears to finish the installation and then the phone shuts down again.
chafik94 said:
thanks for the reply, i did already, but i guess i'll go ahead and try it again.
#update: Yup, the same problem, the little Android robot appears to finish the installation and then the phone shuts down again.
Click to expand...
Click to collapse
Then I recommend you to try that instruction http://forum.xda-developers.com/galaxy-s3/help/recovery-twrp-flashing-using-odin-gt-t2680354
If it success you will have access to a custom recovery, this will allow you to flash any rom and unbrick your device
I missed with the bootloader section so probably that's what caused everything, and i couldn't find a proper bootloader for my S3, which is why i thought it'd be better to ask people with better knowledge in this field, i actually found one yesterday which is "ICS_Bootloader_I9300XXALEF.tar" but it failed. so i thought maybe it's not compatible with my firmware or something and in order to get things right i have to reinstall everything as i mentioned earlier, but that's based on mere guessing, I really need people with better knowledge to tell me what to do, i mean as long as odin is getting my phone and writing to it, i believe it can be fixed.
olimar7184 said:
Then I recommend you to try that instruction http://forum.xda-developers.com/galaxy-s3/help/recovery-twrp-flashing-using-odin-gt-t2680354
If it success you will have access to a custom recovery, this will allow you to flash any rom and unbrick your device
Click to expand...
Click to collapse
thanks allot for your help, I tried this and it succeeded but I still can't turn the phone on nor go to recovery mode
If you really can't boot in recovery mode (vol up + home + power) I don't know what to do sorry...
Last possibility that i can think about : Just make sure you are using a I9300 s3, because there are other versions, and the file that you used to root your phone "CF-Auto-Root-d2att-d2uc-samsungsghi747.tar.md5" (at the beginning of your first post) is for d2att, and I747 not for I9300. + you say latter that you flashed I9300 bootloader "ICS_Bootloader_I9300XXALEF.tar"
The d2att and I747 use qualcomm processor, they are very different from the I9300 with exynos processor.
So check behind the battery witch version do you have.
olimar7184 said:
Just make sure you are using a I9300
Click to expand...
Click to collapse
it is I9300 but i wasn't sure about the auto-root file so that's what brought me here I didn't double check everything before trying the root
here's what the back of the phone says
Model: GT-I9300
FCC ID: A3LGTI9300A
SNN: -I9300GSMH
chafik94 said:
it is I9300 but i wasn't sure about the auto-root file so that's what brought me here I didn't double check everything before trying the root
here's what the back of the phone says
Model: GT-I9300
FCC ID: A3LGTI9300A
SNN: -I9300GSMH
Click to expand...
Click to collapse
to go to recovery :
You tried vol up + home + power ? (when unplugged)
Or just vol up + home when you cancel download mode ? (when plugged)
Because if I understood correctly, when your device is not plugged you can do anything at all ?
And when you plug in your computer it goes in download mode ? Is this also happening when you plug on a wall charger ?
olimar7184 said:
to go to recovery :
You tried vol up + home + power ? (when unplugged)
Or just vol up + home when you cancel download mode ? (when plugged)
Because if I understood correctly, when your device is not plugged you can do anything at all ?
And when you plug in your computer it goes in download mode ? Is this also happening when you plug on a wall charger ?
Click to expand...
Click to collapse
yup, that's exactly what happens, and yes it happen when on the wall charger as well, but the phone doesn't give any sign that it's being charged, and when I unplug it while it's on it turns off immediately. i tried the other method you mentioned about recovery mode, and still nothing happens, the phone shows Samsung galaxy SIII logo and turns off again.
chafik94 said:
yup, that's exactly what happens, and yes it happen when on the wall charger as well, but the phone doesn't give any sign that it's being charged, and when I unplug it while it's on it turns off immediately. i tried the other method you mentioned about recovery mode, and still nothing happens, the phone shows Samsung galaxy SIII logo and turns off again.
Click to expand...
Click to collapse
It's probably an hardware problem, because you said you tried 2 different batteries, and even soft-bricked, the phone should stay on when unplugged
And I have no others ideas how to try to fix it, i am very sorry
olimar7184 said:
It's probably an hardware problem, because you said you tried 2 different batteries, and even soft-bricked, the phone should stay on when unplugged
And I have no others ideas how to try to fix it, i am very sorry
Click to expand...
Click to collapse
Thanks allot for your time, i really appreciate your help, i'll wait if someone else has a solution
olimar7184 said:
It's probably an hardware problem, because you said you tried 2 different batteries, and even soft-bricked, the phone should stay on when unplugged
And I have no others ideas how to try to fix it, i am very sorry
Click to expand...
Click to collapse
I managed to repair my phone today, apparently it was a faulty battery, i used a naked charger to revive it (took off old charger's phone side as shown in the picture, stuck the Black wire to the metal above the positive sign, and the green wire to the one above the negative sign, placed the battery on the phone with the charger in between them and plugged it on the wall for a few seconds, and the phone turned on just fine),
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i re-applied the firmware and this time the android robot where the phone used to shutdown while installing, now completed it's job and the phone rebooted normally, I noticed a yellow text overlaying on the screen, done some more research and found out it is called "Factory mode" (I am a noob you know) so I had to Root the phone to get rid of this problem and this time, thank the Lord, I succeeded in rooting it because I double checked everything lol.
BUT..., Lol when you screw something up, you just have to keep patching it, you fix something here, an other problem appears over there hahaha.
anyways, the problem now is the network, I do have signal and it changes when i put the phone in different places with different signal strengths, and the clock is perfectly updated, but i use the phone as a phone and call people, it gives me this message:
I tried allot of things trying to fix it, nothing seemed to help, and then it came to my mind that probably what I did wrong was download my Service Provider's firmware, maybe the phone Had the international firmware i can't remember and i didn't check it before, the friend i bought it from just told me he brought it brand new but not from a service provider which means it had an international firmware, so now I am downloading a firmware from sammobile that had Unknown in Country, and here's its full title "I9300XXUGNJ2_I9300MSTGNJ1_MST.zip".
My question now, if my theory was wrong and i did somehow apply the right firmware at the first time, will it damage the phone if I applied a different firmware from other Service providers, and i mean this firmware that i am currently downloading?
PS: when the phone turned on the first time the battery had above 70% of charge, i'd like to know what caused the battery to go faulty all of a sudden even while having enough power!
chafik94 said:
I managed to repair my phone today, apparently it was a faulty battery, i used a naked charger to revive it (took off old charger's phone side as shown in the picture, stuck the Black wire to the metal above the positive sign, and the green wire to the one above the negative sign, placed the battery on the phone with the charger in between them and plugged it on the wall for a few seconds, and the phone turned on just fine),
i re-applied the firmware and this time the android robot where the phone used to shutdown while installing, now completed it's job and the phone rebooted normally, I noticed a yellow text overlaying on the screen, done some more research and found out it is called "Factory mode" (I am a noob you know) so I had to Root the phone to get rid of this problem and this time, thank the Lord, I succeeded in rooting it because I double checked everything lol.
BUT..., Lol when you screw something up, you just have to keep patching it, you fix something here, an other problem appears over there hahaha.
anyways, the problem now is the network, I do have signal and it changes when i put the phone in different places with different signal strengths, and the clock is perfectly updated, but i use the phone as a phone and call people, it gives me this message:
I tried allot of things trying to fix it, nothing seemed to help, and then it came to my mind that probably what I did wrong was download my Service Provider's firmware, maybe the phone Had the international firmware i can't remember and i didn't check it before, the friend i bought it from just told me he brought it brand new but not from a service provider which means it had an international firmware, so now I am downloading a firmware from sammobile that had Unknown in Country, and here's its full title "I9300XXUGNJ2_I9300MSTGNJ1_MST.zip".
My question now, if my theory was wrong and i did somehow apply the right firmware at the first time, will it damage the phone if I applied a different firmware from other Service providers, and i mean this firmware that i am currently downloading?
PS: when the phone turned on the first time the battery had above 70% of charge, i'd like to know what caused the battery to go faulty all of a sudden even while having enough power!
Click to expand...
Click to collapse
I don't it will damage your phone, you can try to flash. But instead of taking "unknown" in country, just take your own country.
And check your imei in the setting> about phone > status.
About the battery i really don't know, because i never had this problem with my own s3 before.
olimar7184 said:
I don't it will damage your phone, you can try to flash. But instead of taking "unknown" in country, just take your own country.
And check your imei in the setting> about phone > status.
About the battery i really don't know, because i never had this problem with my own s3 before.
Click to expand...
Click to collapse
I've been trying to fix the IMEI the whole day yesterday, I have the 0049 IMEI i googled it and allot of people had the same problem and the same IMEI, it is not the same as the IMEI behind the battery, one weird thing, when I tried Samsung tool pro to unlock the device, the software said that I had a firmware from Ghana , and I am very sure I was using the Moroccan firmware, now that i installed the unknown firmware it says Belgium, but it shows the same problems, wrong IMEI, wrong Serial Number, and the same error "zTool not found for selected model"
Operation: Unlock
Selected model: GT-I9300
Software version: 24.3
Waiting ADB device... OK
Reading phone info...
Model: GT-I9300
Android version: 4.3
Product code: Not Active
Phone version: I9300BUUGNF1
PDA version: I9300XXUGNJ2
CSC version: I9300MSTGNJ1
CSC country code: Belgium
CSC sales code: MST
HW version: REV__
Phone S/N: 00000000000
Modem board:
RF cal date: none
IMEI: 004999010640000
Checking Super user right... true
Reading nv data... OK
Checking magic... OK
zTool not found for selected model
Done with Samsung Tool PRO v.24.3
i'm really stuck here, been trying everything yet can't find a solution yet
oh, i think that "Ghana" thing happened because i was trying some modem patches like "Modem_I9300_NF1.tar.md5" to unlock the device but they didn't help and i totally forgot about them. lol
chafik94 said:
oh, i think that "Ghana" thing happened because i was trying some modem patches like "Modem_I9300_NF1.tar.md5" to unlock the device but they didn't help and i totally forgot about them. lol
Click to expand...
Click to collapse
Flash the firmware of your country.
And this http://forum.xda-developers.com/galaxy-s3/general/ref-imei-efs-stuff-i9300-including-t2393289 may help you if flashing the firmware of you country don't work