Related
HELP!
I recently replaced my x10 mini pros cracked screen and when i put the top section back on the screen goes from being ok "showing the slide to unlock" to a blank screen with faint horizontal lines on it!!! and when i remove the top section of the phone it works again? the cable is attached fine and the new screen is working, what is going on please i spent alot of money on thios phone i need help
Thanks alot if you can help, i can take pictures of it if you need to see.
Hello,
When I look straight to the screen of the S2 it looks ok
When I look over the screen when I hold it 20 degrees backwards it has a green glow over the screen
Is this normal or is there a problem with the screen?
Yes it is a question .
jje
Please use the Q&A Forum for questions Thanks
Moving to Q&A
This is probably a dumb question. My number 4 phone button is suddenly not working. I ran the calibration in HTC sense keypad, but that's the one that has you type a sentence. Is there one to calibrate phone pad?
jeffrimerman said:
This is probably a dumb question. My number 4 phone button is suddenly not working. I ran the calibration in HTC sense keypad, but that's the one that has you type a sentence. Is there one to calibrate phone pad?
Click to expand...
Click to collapse
I don't think that there is a specific process to calibrate the number pad. Does that area of the screen work for other things, like pressing a link?
Also, for future questions, please post them in the Q&A section.
You are now in the Q&A. Here you may receive a better/ more through response :good:
FattySparks said:
I don't think that there is a specific process to calibrate the number pad. Does that area of the screen work for other things, like pressing a link?
Also, for future questions, please post them in the Q&A section.
Click to expand...
Click to collapse
Ok I'll post over there. I think it's the screen itself and not so much the calibration of it. It was that whole section of the screen that was acting funky. When I went to an empty home page and dragged an icon it would force drop it at that point as if I we lifting my finger up. And now this morning it's fine. Maybe knocking it around over night helped
jeffrimerman said:
Ok I'll post over there. I think it's the screen itself and not so much the calibration of it. It was that whole section of the screen that was acting funky. When I went to an empty home page and dragged an icon it would force drop it at that point as if I we lifting my finger up. And now this morning it's fine. Maybe knocking it around over night helped
Click to expand...
Click to collapse
The thread has already been moved, so don't worry about it.
Hi guys, I have been having an issue with my i9305 where a touch point seems to stick and my phone won't respond properly to other touch Input, sometimes looks like it's having a bit of a fit, it's as if I'm holding a finger down on one point. I have broken the screen a couple of times and replaced it but most of the time it works flawlessly, it seems a lot like a software or driver issue, happens exactly the same across all roms, long pressing seems to set it off the most, stays stuck unti I Switch my screen off and on and unlock it's fine again, can happen every few seconds or might not happen all day, any thoughts?
You say you have broken and replaced your screen twice, which is very unusual, so are you sure you didn't drop your phone since the last screen replacement? Also, did you take the phone to an authorised service center or did you replace the screen yourself, with parts that you acquired? Maybe you have a faulty screen that needs replacement once again.
iR¡[email protected]!* ? from i9300 via Tapatalk 2
The screen has been cracked slightly in my pocket twice, only ever a crack, not smashed or anything, don't know what happened the first time but the second time I tried to pick something up and it leaned against my phone in my pocket and cracked the screen, I have replaced the glass myself twice, only light heat and gentle separation, replaced with glass and adhesive membrane like original, the digitiser seems completely untouched. It probably is something to do with the digitiser or screen, I just wanted to see if it is happening to anyone else before I fork out for a new digitiser, would be more cost effective to just buy a new phone. Just seems like a software or firmware thing by the way it acts and is fine after a quick on off of the screen, as if there is some cache for the touch control that gets cleared when I Switch the screen of, dunno.
[READ THlS FlRST] POST QUESTIONS IN THE Q&A SECTION AND NOT HERE!!!!
I9305 Q&A
jje
I dropped my gs6 and the screen cracked but the screen doesnt turn on.
The led indicator and soft button turns on but there is no life on the screen itself.
So does this mean that i only need to replace the screen or is there some internal damage?
Thanks!
Edit: Posted this on wrong thread, I was talking about galaxy s6, not the edge version. So if the mod could delete this post, i would appreciate that
fibito said:
I dropped my gs6 and the screen cracked but the screen doesnt turn on.
The led indicator and soft button turns on but there is no life on the screen itself.
So does this mean that i only need to replace the screen or is there some internal damage?
Thanks!
Edit: Posted this on wrong thread, I was talking about galaxy s6, not the edge version. So if the mod could delete this post, i would appreciate that
Click to expand...
Click to collapse
Should be just screen nothing internal.