Hello...
Sorry if my Thread have been suggested before i did not find one suggest over here
so my question is ... anyone did flash JB modem on ICS stock rom?
if yes and worked , can some one throw a link for JB modem for G.N SGH-I717 .. my single keep down almost the time :crying:
There is a search button and I've done it ..........
my addiction:Flashing.
thank you shy
i got lost in searching ... so please could you help me out !!?
Just type for modems .......im on mobile and working so i can't link you at the moment .... Try looking for ucmb4 modem for our i717
my addiction:Flashing.
I know what they say about assuming, so hopefully it only takes place on your part here, but if you're assuming newer = better, you're very wrong. If you're on ICS, you aren't going to net any improvement by going to a JB modem. I know, without a doubt, ICS modems on stock JB cause major problems, so they really are software dependent. On top of that, if you're going it hoping to increase data with another (not AT&T) provider, you're picking a horrible modem to try that with. UCMB4 is the crowned ICS king of reception & data, and the blaze modems are a close second.
Modems are independent of versions so flash any modem you want.
rangercaptain said:
Modems are independent of versions so flash any modem you want.
Click to expand...
Click to collapse
This is someone who's run an ICS modem on stock jellybean for months. Trust him.
Anthony820 said:
This is someone who's run an ICS modem on stock jellybean for months. Trust him.
Click to expand...
Click to collapse
Running a Bell JB modem file over JB Sandwich rom (ICS based) and it runs fine so far
Related
hi
i flashed the latest stock I9100XILA2 (Italy),just flashed the csc for my country instead of italy.
I saw that the modem shipped with this latest rom (januar 2012) , XWKI1 is older then the one that came with my rom xxkk2 from november 2011,which is xwki4.
is it recommended to stick with the modem that came with the rom?like are there optimizations in that rom for that specific modem,so it works best with that rom?
Or doesnt it matter what modem one uses?
i tested both (flashed with odin),but no way to judge on the performance,because of heavy fluctuations on the local net,which gives very different results after each test run,with both modems.
Apreciate any information on this.
Thanks.
Try out a bunch of modems and use whichever gives you the best performance. You might need to test each in different locations/different times of the day & so on to get a good guide. That's what I did before I settled on the modem I've been using for the last month and half.
No need to stick to a modem that was packaged with a particular rom
thanks for your answer
which modem do you use now,or do you think is the best for you?
cheers
egalwaat said:
thanks for your answer
which modem do you use now,or do you think is the best for you?
cheers
Click to expand...
Click to collapse
use LP1 or KL1 you can find them in the sticky thread in the original development thread...i am currently using LP1 and getting good signal
Like the topic says, I have an AT&T note, but T Mobile service. I recently (last night) found the wonderful work by several XDA members of which they supply us with a flashable zip that contains a radio that will give T Mo 4G data speeds.
I forget which one I finally used (there's the SGH-T989 KID radio, VKL1 radio and one called blaze). There is also a build.prop file that completely rendered my device useless (requiring an OS re-install).
I also have a few ICS modems, again the "KID" or is it "K1D" Im not sure... that, the "Blaze" version and one from the carrier "Telus". I also saw a Rodgers version floating around somewhere. I think that was really for the Galaxy S2 but it works with our Note
Anyway I am really missing ICS, I have 2.3.6 now. I need to know what is a good modem radio to flash if Im going ICS. Also whats a good ICS rom (keeping in mind the flashing of the T Mo radio)...
thanks
Roms and modems are interchangeable, meaning you can use whichever modem you want, on whichever Rom you want.
The blaze modem is what you want to use for t-mobile
Also the apn settings for t-mobile would probably be beneficial
studacris said:
Roms and modems are interchangeable, meaning you can use whichever modem you want, on whichever Rom you want.
Click to expand...
Click to collapse
So it doesn't matter if the Rom is gingerbread based but the modem is from an ICS build? And Vise/Versa...?
Nope
hi , i flashed the REMICS jelly bean rom and i lost data and network. i made a reasearch to this problem and the solution was to flash i new modem. I have flashed lots of modems but none every worked. Can someone please tell me the right one to flash because i am getting tired of flashing different modems. Thank you very much.
kwartey said:
hi , i flashed the REMICS jelly bean rom and i lost data and network. i made a reasearch to this problem and the solution was to flash i new modem. I have flashed lots of modems but none every worked. Can someone please tell me the right one to flash because i am getting tired of flashing different modems. Thank you very much.
Click to expand...
Click to collapse
u dont install remics jb till it gets updated ,,,,,,it has plenty of bugs....it is going to get an updated within 2 weeks wait till then.......modems no one can say whichone is good because u have to flash diffrent modems and see which is proper for ur area.....i cant say much....:laugh:...........see this http://forum.xda-developers.com/showthread.php?t=959088
HIT THANKS IF I HAVE HELPED
kwartey said:
hi , i flashed the REMICS jelly bean rom and i lost data and network. i made a reasearch to this problem and the solution was to flash i new modem. I have flashed lots of modems but none every worked. Can someone please tell me the right one to flash because i am getting tired of flashing different modems. Thank you very much.
Click to expand...
Click to collapse
^^;; The RemICS JB is currently being fixed. The current version is known to give no data or network as a result from a kernel issue...flashing any modems will not give you signal.....You really must read as much of the thread to the rom you plan to flash as you can before actually committing, otherwise things like this are bound to happen my friend ^^ If you did a nandroid I'd suggest reflashing that, or going to another JB or ICS rom until REM is updated.
Good luck!
Thanks to u all
Sent from my SGH-T959 using xda premium
Uuuuuuugggggghhhhhhh.........
Really???????
Sent from my SGH-T959 using xda premium
hello fellow xdas
while back i had gotten my hands dirty with the CM10 project as i just couldn't wait for the official update! i learned quickly that i had serious problems with antenna/reception. i tried carious base bands (as recommended on forums) using GetRil/flash.Odin. this didnt seem to help, even though i would get better reception, my signal was unstable. In the process i tried other roms like JellyBam and had the same issue.
As this is my main phone and i do actually need to call with it, i went back to the stock rom i downloaded. but surprisingly i still have the same issue! GetRil also shows that i have incompatible RIL/baseband. this is what it shows:
RIL: I9100NELP2; I9100XXKI4
Baseband: I9100XXLPQ
FYI: i am located in the Netherlands and use T-mobile network.
so have i installed the wrong ROM or done something wrong in the process... ? does anyone have any experience with this? i much rather have CM10 but only if i can get to call normally once again?
thanks
ozeeo said:
hello fellow xdas
while back i had gotten my hands dirty with the CM10 project as i just couldn't wait for the official update! i learned quickly that i had serious problems with antenna/reception. i tried carious base bands (as recommended on forums) using GetRil/flash.Odin. this didnt seem to help, even though i would get better reception, my signal was unstable. In the process i tried other roms like JellyBam and had the same issue.
As this is my main phone and i do actually need to call with it, i went back to the stock rom i downloaded. but surprisingly i still have the same issue! GetRil also shows that i have incompatible RIL/baseband. this is what it shows:
RIL: I9100NELP2; I9100XXKI4
Baseband: I9100XXLPQ
FYI: i am located in the Netherlands and use T-mobile network.
so have i installed the wrong ROM or done something wrong in the process... ? does anyone have any experience with this? i much rather have CM10 but only if i can get to call normally once again?
thanks
Click to expand...
Click to collapse
Use either of the 2 links below to download either the NELP2 modem of the XXKI4 modem, and them flash them onto your phone via Recovery Mode. That should resolved your incompatible RIL issue.
[REF] Modem+RIL CWM Installers
[REF] Galaxy S 2 Shipped Modem Collection
---------- Post added at 11:55 AM ---------- Previous post was at 11:46 AM ----------
OR .... use the link below to find and reflash the entire correct firmware for your region, which should flash the correct modem and RIL along with it.
[ROM+Guide] Official i9100 Firmwares LPE/Q/7/2/F/S/4/7/G/9/W/D/F Download
zee54 said:
Use either of the 2 links below to download either the NELP2 modem of the XXKI4 modem, and them flash them onto your phone via Recovery Mode. That should resolved your incompatible RIL issue.
[REF] Modem+RIL CWM Installers
[REF] Galaxy S 2 Shipped Modem Collection
---------- Post added at 11:55 AM ---------- Previous post was at 11:46 AM ----------
OR .... use the link below to find and reflash the entire correct firmware for your region, which should flash the correct modem and RIL along with it.
[ROM+Guide] Official i9100 Firmwares LPE/Q/7/2/F/S/4/7/G/9/W/D/F Download
Click to expand...
Click to collapse
thanks a lot zee54,
can i just go back to my CM10 or JellyBam, install the above mentioned radios and get everything working? or does it depend on the RIL which that ROM is running! I have tried a number of modems when i had CM10, but dont know if i tried those... i did try BVLP7 for sure
Based on this forum right here i need to have the I9100BOLPD ROM as stock for Netherlands T Mobile!
ozeeo said:
thanks a lot zee54,
can i just go back to my CM10 or JellyBam, install the above mentioned radios and get everything working? or does it depend on the RIL which that ROM is running! I have tried a number of modems when i had CM10, but dont know if i tried those... i did try BVLP7 for sure
Based on this forum right here i need to have the I9100BOLPD ROM as stock for Netherlands T Mobile!
Click to expand...
Click to collapse
The modem is independent of the ROM, mate. So it wont make much of a difference whether you install the radio on stock firmware or on CM10. You could try using the modems mentioned by zee54 with CM10 and seeing if it helps. Also, give it about a day or so..since the phone tends to take a while to get 'used' to a new modem.
ozeeo said:
thanks a lot zee54,
can i just go back to my CM10 or JellyBam, install the above mentioned radios and get everything working? or does it depend on the RIL which that ROM is running! I have tried a number of modems when i had CM10, but dont know if i tried those... i did try BVLP7 for sure
Based on this forum right here i need to have the I9100BOLPD ROM as stock for Netherlands T Mobile!
Click to expand...
Click to collapse
The unstable signal or "RIL Crash" as it it called isn't actually caused by having an incompatible RIL and Baseband (modem). It is a more complicated issue which I don't fully understand myself. But what I do know is that it currently affects all customs roms that are based on CM10 and use the CM Kernel. So switching modems might help recude the frequency of the problem but probably won't irradicate it completely.
You should not experiencing this problem if you go back to stock samsung firmware. If you experience problems you might want to do a full wipe (Data, Cache, Dalvic-cache) before reflashing and fix permissions afterwards.
On a more positive note, I have found that using the Siyah Kernel with your custom rom does seem to eliminate this problem, or at least reduce it occurance to such that I have not noticed it happening.
So personally i would suggest that if you wish to go back to CM10 or JellyBam ROMs, then do so but also install the latest Siyah Kernel for the S2 from here http://www.gokhanmoral.com/
(Here's the XDA Thread for the Siyah Kernel - [KERNEL] SiyahKernel v4.1.5 (v5.0a2))
I am currently running CM10 with the Siyah Kernel v5.0b2 and it is working very nicely
great stuff guys... 2x thanks for both of you!
Zeey54, i just had Siyah v5 Kernal installed, installing the latest JellyBam right now! so lets see what happens. i was suspecting that beside the RIL/baseband there were other factors as i did not see any significant difference between them. but then again i dont trust my judgement on such issues as my knowledge is quite limited.
will send an update with the result after installation in a few min.
ozeeo said:
great stuff guys... 2x thanks for both of you!
Zeey54, i just had Siyah v5 Kernal installed, installing the latest JellyBam right now! so lets see what happens. i was suspecting that beside the RIL/baseband there were other factors as i did not see any significant difference between them. but then again i dont trust my judgement on such issues as my knowledge is quite limited.
will send an update with the result after installation in a few min.
Click to expand...
Click to collapse
Good luck mate. I hope it all goes well
zee54 said:
Good luck mate. I hope it all goes well
Click to expand...
Click to collapse
installed the BOLP7 modem, overall reception is much better! data connectivity is also better and faster. but i still have some periods which my receptions drops and goes back up, seems like radio/modem crash (if im right). dont know if that is due to the kernel or modem or ...?
the reason i went for BOLP7 modem was because the latest official stock rom from t-mobile Netherlands was I9100BOLPM_I9100TNLLP8_I9100BOLP7, so i thought that would be the best one to try!
will wait a little more to see if this improves as the modem settles.
4th official ROM too much coverage you please make a review ?
need modem
First of all, thank you mate for your hardwork and awesome utility.
I have a Samsung galaxy S2 I9100G , recently flashed jelly bam custom rom. I am based in Saudi Arabia, the reception is not clear and people complain that it is switched off or out of network. I tried calling with another mobile and i got a response that my mobile is switched off, at the same time i checked my S2 mobile , it shows the full signal of the network in status bar.
what should i do? Which modem should i flash. the getRIL shows RIL/baseband is matching (I9100GDDLP5).
cheers
Rizwan
Hey guys,
I've been running various JB ROMS for a while, mainly Omega but now on Fox Hound. Ever since I went to a JB ROM my signal strength when using auto or WCDMA only network mode has been really bad. I only get good signal when using GSM only. Problem is data is pretty slow on GSM.
It seems that JB modems could be the problem so I've tried flashing various other JB modems and even some ICS versions, all have had very little effect.
Has anyone else experienced this problem with low signal, I'm tempted to flash back to an ICS rom
syztemlord said:
Hey guys,
I've been running various JB ROMS for a while, mainly Omega but now on Fox Hound. Ever since I went to a JB ROM my signal strength when using auto or WCDMA only network mode has been really bad. I only get good signal when using GSM only. Problem is data is pretty slow on GSM.
It seems that JB modems could be the problem so I've tried flashing various other JB modems and even some ICS versions, all have had very little effect.
Has anyone else experienced this problem with low signal, I'm tempted to flash back to an ICS rom
Click to expand...
Click to collapse
did u try flashing a modem that was meant for ur region?
rebairo said:
did u try flashing a modem that was meant for ur region?
Click to expand...
Click to collapse
Yes, all the versions I tried where UK modems.
try to flash other kernel...
Dont flash a kernel check the RIL thread but my guess would be network problem .
jje
JJEgan said:
Dont flash a kernel check the RIL thread but my guess would be network problem .
jje
Click to expand...
Click to collapse
Thanks JJ, I'll check the thread out. I'm not sure it's a network issue though as it seemed to work fine when I was on an ICS ROM.
Just tried a few files from the thread but still not very good. Think I'll try an ICS ROM.