Related
I am trying to un-softbrick my Galaxy S Vibrant. I attempted (Following the guide to a damn T) to install http://forum.xda-developers.com/showthread.php?t=1192438 the RevolutionRom on a stock (factor reset, stock firmware) phone.
Odin rebooted the phone, the Bullet installer voice played various messages. On one of the reboots the voice now just repeats "Convert data partition, not enough space on partition".
What I have tried:
Cannot access Download mode. (holding +/- on usb plugin just shows the battery level and the voice plays the message during)
Cannot load into recovery mode (boots back into Bullet screen, replays message).
How do I get this phone back to normal? I underestimated the "simple noob" directions posted on that thread, apparently it's not a 100% term.
Edit: I feel like this is the point where I need to invest in a hardware jig. The phone will only go into the charging screen or the bullet loading screen and the annoying voice. Recovery mode and/or download mode are inaccessible. i have tried every method posting and 3 button combo, no luck on download mode.
Does this sound like a hardware lock? I am really hoping this is recoverable. Thanks.
Some additional info (steps I took to get to this point)
Phone was previously in "stock" condition i.e. still had Avatar on the screen.
1.) Factory Reset (allow phone to boot)
2.) Power Off
3.) Vol +/Vol + usb cable (Download mode)
4.) Fire up Odin3_v1.0
5.) unplug and replug usb (odin reports com3 open)
6.) download RevolutionJVQFinalUpdate2OdinWITHBOOTLOADERS.tar.md5
7.) click "PDA" navigate to the above download
8.) leave all other buttons checked as default in Odin (Auto Reboot, F Reset Time)
9.) hit start, wait
10.) Odin did the md5 check, uploaded some files, and rebooted the phone, after that the phone played a message similar to "creating partition, please wait 2 minutes"
11.) after 1-2 restarts, the phone started looping, saying "convert partition, not enough space on partition".
12.) above post is post issue diagnostic
I am more curious as to what I did "wrong" than anything else. I see if this is a hardware issue a jig can be used to access download mode. Just not sure why the three button salute puts me in this weird charging + "convert partition, not enough space" combo. It doesn't seem like the phone is super bricked, but it doesn't match any searched for symptoms I have seen with HWL phones either.
Expert advice appreciated!
got it!.
Wow.
So the revolutionrom is apparently european based. I had to use VOL+ and USB cable to enter download mode. Worked on the first try. Time to odin back to stock and find a new rom.
Hope this helps someone.
I believe that means you are using the Gingerbread bootloaders. Power or USB + Volume Up is Download Mode, and Power or USB + Volume Down is Recovery Mode.
Ahh that explains it.
I just used odin to reflash the stock PIT and tmobile T959UVjI6 rom to it, and it still shows this behavior (vol + to recover, and the sim card won't read now).
I can get a rom to boot now at least
Do I need to check "re-partition"? I assumed the PIT file forced a re format.
NM got it. Froyo bootloader installed, all back to stock, SIM recognized.
Now I am just gonna use cyanogenmod's installation process ha.
Thanks for the tip, pointed me in the perfect direction.
I normally do. But I would also grab the stock JFD odin tar and use that instead of JI6.
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Jokesy said:
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Click to expand...
Click to collapse
It Is a GT-I9100
mcguirestick said:
It Is a GT-I9100
Click to expand...
Click to collapse
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Jokesy said:
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Click to expand...
Click to collapse
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Poroto said:
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Click to expand...
Click to collapse
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Jokesy said:
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Click to expand...
Click to collapse
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
mcguirestick said:
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
Click to expand...
Click to collapse
can you enter recovery now?
Jokesy said:
can you enter recovery now?
Click to expand...
Click to collapse
Hi, Nope still can only get to boot load not recovery
mcguirestick said:
Hi, Nope still can only get to boot load not recovery
Click to expand...
Click to collapse
I think your data partition is corrupt, but you can still get it solved.
You need to special .pit file. I'll post you the link (for the .pit file and instructions) very soon
Try this it worked for me
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
ScottsDesk said:
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
Click to expand...
Click to collapse
Hi Tried it again no luck
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Jokesy said:
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Click to expand...
Click to collapse
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
marceloasr said:
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
Click to expand...
Click to collapse
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
TRY THIS!
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Try this I did and it worked to get mine booting after a bad update.
I messed around with it using several methods of getting it to boot into download mode until I finally got it to do it. I think I left it plugged into the USB, powered it down until I saw the charging screen, then I proceeded to play with the different ways to hold the buttons to get it to download mode. If you are persistent enough and read a little on booting methods to get bricked phone into download mode you will succed if not then your not for the world of trial and error... the main thing is do the first steps I said before until it works
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
or try
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
any how try try try until it works
Once in download mode
Get your files together for your phone, and use Odin 1.85.
Plug into Odin and make sure it shows yellow and its added!
1. Now if your files have like 3 files and the exact .pit file for your phone if available.
I found mine here (Find yous stock firmware for your phone)
CLICK HERE
2. Click the PIT button and browse to your exact .pit file for your phone *It should now have added a check in the re-partition box under the options area of the Odin window. If not CHECK IT!
***If you don't have your .pit don't worry about this unless you suspect, or have a bad partition
3. If you have just 1 file just click the PDA button and load the file. If you have 3 then you will load the PDA file in PDA, the Modem file into PHONE, and the CSC file into CSC, there are way too many phones to link all the files so get you stuff together!
4. Now hit start.
5. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
6. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
7. As soon as the phone shows the first sign of starting up IE Logo or whatever let go of all buttons and using the Vol Up down Choose the Clear Cache option and go through and make sure you factory reset it if you can just for good measure.
8. Reboot
9. Now when the phone shows the first sign of starting up IE Logo or whatever take out battery again to power off
10. Now put it back in and start it in Download mode by pressing Vol Down, Home at the same time then the Power button.
11. Once in download mode Hook up to Odin again and flash it with a root kernel for your phone. Do not ask me just find it. I did it took time but I got all the files together over several days of reading and collecting the correct ones.
12. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
13. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
14. In most roots you will now have a advanced or mounting options and more options to use.
15. I cleared the Cache again, Cleared the Davilik Cache, Went into a option and actually mounted the cache formatted the Cache.
16. Use the option now to restart the phone...
And mine started up installed the apps and I am up and running, nice and smooth and no issues so far
I hope this helps out someone whos just about to go off the deep end, as I was there and patience and trial and error came up with this step by step way to recover mine. Thank me by hitting the little thumbs up THANKS button below this post.
And if your so happy your phone is up show your appreciation by buying me a Pepsi
Jokesy said:
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
Click to expand...
Click to collapse
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
mcguirestick said:
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
Click to expand...
Click to collapse
Sorry for your luck! Cheers!
So, I was off attempting to root my phone with CF-Auto-Root. I have an S6 Edge from T-mobile, and so I selected the one for the SM-G925T, which was my phone's model number. On using Odin, following all the steps from the youtube video titled "How to Root Galaxy S6 or S6 Edge!" by Max Lee at High on Android (Sorry I can't post a link, I'm too new) Anyway, once I got to the part where I was rooting, upon restart, my phone seems to be locked in the startup screen. In the upper right corner in red, it says "Recovery is not seandroid enforcing" other than that, the screen is black with some white text that says "Samsung / Galaxy / S6 Edge / Powered By / Android" With each "/" representing a line break.
When I hold down the power button, nothing happens. Did I just ruin this phone, or is there something I can do to fix it? (I fear I may have unplugged it too early... I waited ~5 minutes before I figured it was totally frozen and that I would need to do something. Hopefully that didn't ruin the root...)
Thanks for any help!
Disclaimer, I'm no expert.
First, take a couple of deep breaths, your phone is not lost to the world.
Sounds like your stock firmware is kicking up a fuss about being booted from a non-samsung recovery.
There are several threads about this particular error already, but the general gist seems to be to get your phone back into Download Mode (power button + volume down + menu button) and flash your stock firmware back in.
That will probably remove root and clear your data though.
Do a Google for "Recovery seandroid enforcing s6" if you havn't already
Sent from my SM-G925I using Tapatalk
This is quite normal. The same thing happened to me.
If you've got as far as flashing TWRP via Odin then it should just be a matter of booting into recovery. As you're in a place where your phone will keep trying to boot even if you power off, it's just a matter of timing.
To shut the phone down you need to hold Power and Vol Down for about 10 seconds. What you'll find though is the phone will boot up again straight away and show you the annoying Seandroid screen so what you need to do is power off the phone then as soon as the screen goes black hit Vol Up, Home and Power. Keep holding them and instead of booting to Seandroid it should boot to TWRP. If you get Seandroid just try again. You need to get those buttons pressed as soon as the phone starts to boot-cycle though.
Once you're in TWRP you can install root, and then install the kernel which will allow the phone to boot normally again.
Good luck!
Mischala said:
Disclaimer, I'm no expert.
First, take a couple of deep breaths, your phone is not lost to the world.
Sounds like your stock firmware is kicking up a fuss about being booted from a non-samsung recovery.
There are several threads about this particular error already, but the general gist seems to be to get your phone back into Download Mode (power button + volume down + menu button) and flash your stock firmware back in.
That will probably remove root and clear your data though.
Do a Google for "Recovery seandroid enforcing s6" if you havn't already
Sent from my SM-G925I using Tapatalk
Click to expand...
Click to collapse
Yeah, I was just googling around to see if anyone had more luck. I'm currently downloading 5.1.1 (I didn't know that Samsung changed the bootloader, so I'll have to wait for that root to come out. Oh well...) Hopefully it goes well I'll update with results once it's done downloading!
The s6 is weird. This is the first Samsung phone that when using cf-auto root it soft-bricks my phone. You have to flash recovery through odin, then root through recovery for it to work. Dont forget the no sleep fix while you're there.
Here are the steps and links:
1. Download ODIN v 3.10.6 from http://forum.xda-developers.com/show....php?t=2711451 and extract it to a folder.
2. Download TWRP v2 by eousphoros (Odin Flashable Version) from https://mega.co.nz/#!aQhTnQRR!k-M-j9...swZO3CWYi0mMtI
3. Download the latest SuperSu Beta from http://forum.xda-developers.com/apps...v2-05-t2868133 and transfer it to your internal storage on the phone.
4. Download Deep-Sleep flashable fix from http://forum.xda-developers.com/show...7&postcount=56 and transfer it ot your internal storage on the phone.
5. Put your phone into Download Mode. Power Off, then hold Power+Home+VolDown. At the warning press VolUp to continue.
6. Connect your phone to your computer via the USB cable.
7. Launch ODIN.
8. You will see the text Added! in the status panel (left side).
9. Checkmark the box beside AP and then click on AP.
10. Browse to the TWRP tar.md5 file you downloaded earlier and select it.
11. Wait a few seconds for MD5 check to finish successfully.
12. Press Start. You will see the progress bar at the top and when it's complete status window will have message "All Threads Complete (Succeed 1, Failed 0)".
13. Boot into TWRP (Button combination Power+Home+VolUp) and then flash/sideload SuperSu beta zip and then the deep sleep fix zip that you have on internal storage.
14. Reboot to system. Congratulations, your phone is now rooted.
Click to expand...
Click to collapse
H00pyFr00d said:
This is quite normal. The same thing happened to me.
If you've got as far as flashing TWRP via Odin then it should just be a matter of booting into recovery. As you're in a place where your phone will keep trying to boot even if you power off, it's just a matter of timing.
To shut the phone down you need to hold Power and Vol Down for about 10 seconds. What you'll find though is the phone will boot up again straight away and show you the annoying Seandroid screen so what you need to do is power off the phone then as soon as the screen goes black hit Vol Up, Home and Power. Keep holding them and instead of booting to Seandroid it should boot to TWRP. If you get Seandroid just try again. You need to get those buttons pressed as soon as the phone starts to boot-cycle though.
Once you're in TWRP you can install root, and then install the kernel which will allow the phone to boot normally again.
Good luck!
Click to expand...
Click to collapse
I'm confused... When I use the Vol Down + home + power button, it boots into the normal (as far as I can tell) samsung bootloader thing (at least, the one from 5.1.1) So I don't think I have TWRP installed even. Anyway, it shows up in Odin, so how do I start loading everything? In the Files [Download] section in Odin, I see boxes that say BL, AP, CP, and CSC. Which of those do I select to load up the full backup that I got? (It's about 4GB of data with an .iso, if that makes a difference)
Edit: Basically, I have no MD5 files in the download. (I got it off high off android)
KaminKevCrew said:
I'm confused... When I use the Vol Down + home + power button, it boots into the normal (as far as I can tell) samsung bootloader thing (at least, the one from 5.1.1) So I don't think I have TWRP installed even. Anyway, it shows up in Odin, so how do I start loading everything? In the Files [Download] section in Odin, I see boxes that say BL, AP, CP, and CSC. Which of those do I select to load up the full backup that I got? (It's about 4GB of data with an .iso, if that makes a difference)
Edit: Basically, I have no MD5 files in the download. (I got it off high off android)
Click to expand...
Click to collapse
You will not be able to flash anything in odin if youre not in download mode. If you have trouble getting in download mode, you're doing it wrong. Turn off phone, then press Vol down + power + home and dont release any of those until you see something unusual, such as an android robot. While using odin, NEVER EVER load anything in any other option than AP. As far as backup goes, I don't know what backup you made but you don't restore it though odin thats for sure, you will hardbrick your phone.
polish_pat said:
You will not be able to flash anything in odin if youre not in download mode. If you have trouble getting in download mode, you're doing it wrong. Turn off phone, then press Vol down + power + home and dont release any of those until you see something unusual, such as an android robot. While using odin, NEVER EVER load anything in any other option than AP. As far as backup goes, I don't know what backup you made but you don't restore it though odin thats for sure, you will hardbrick your phone.
Click to expand...
Click to collapse
I can get into the stock Samsung download mode (light blue screen, it says downloading on it..) On the links posted in post number five, none of them worked for me... The thing is, I was trying to load TWRP while my phone was updated to 5.1.1 if that makes any difference... Anyway, it appears that the stock download mode is working, so what do I do now? (From what I've read, I can't really put TWRP on it??)
Alright, I got it working! (Hopefully this will help others get redirected to the right thread, since it took me a while to find this!) Depending on whether or not I am allowed to post links at this point, I may need to post repeatedly here, and I apologize for that, but it's all with the best intents in mind!!!
Anyway, if you do what I did, which is this:
No backup, attempt to root GS6 Edge (SM-G925T from T-mobile) with the 5.0.2 CF auto root, while your phone has already been updated to 5.1.1. It puts you in a boot loop, which really isn't fun, because it doesn't appear that you can fix it... Anyway, I went to the thread, which you can find here: http://forum.xda-developers.com/tmo...recovery-twrp2-8-6-0-g925t-5-1-1-of6-t3143002 . Anyway, what you need to do is boot into download mode (which you can still do when you are in the boot loop, just hold the volume down + home + power buttons until the device boots into the downloader screen. At that point, you use Odin, and install the file called "OF6 Stock Recovery". That should fix it! Anyway, go to the thread above, it helped me a TON!!!
This isn't really rocket science. Yes, there are different root options for 5.0.1 and 5.1.1 but this is clear in the OP when you decide which root to use.
The only things you need to consider are, if you flash a custom recovery (not the 'download mode' that you use for Odin) then the stock rom won't boot. It's not bricked but you just need a custom kernel. Therefore the steps are:
Download and copy the custom kernel and root to the phone
Boot into Download mode -Vol down, home, power - and flash recovery (TWRP etc) via Odin
Boot into TWRP custom recovery - Vol up, home, power - and flash kernel and root
Reboot
Profit
It really is just a matter of reading the steps carefully and doing exactly what they tell you.
This is NOT my work (Ianmacd) and guide is written by Mr Pickles all credits to him for his install method.
Also this is just a copy and paste but the guide is well written and TWRP should cause less issues.
I'm sure Gieti94 is just perhaps busy with other commitments, credit also to him for his fantastic efforts.
Just a new space for the currently working TWRP so all don't get in a pickle.
----------------------------
Download link (Maintained by pickles) best to have all in a tidy and convenient place (Thanks Pickles)
http://bit.ly/2VlcqYd
Install Guide (Draughted by Pickles) very well written.
---------------------------
- NOT A SINGLE STEP IS UNNESSECARY
- DO THEM _ALL_ EXACTLY!
- ALL YOUR DATA WILL BE GONE - BACKUP!
---------------------------------------
DO NOT INSTALL MODPACK FROM SOLDIER - IT BREAKS TWRP!
---------------------------------------
If you have any problems - contact @PiCkLeS or on Telegram by PiCkLeS or @rp4k
---------------------------------------
All development is by @ianmacd (Ian Macdonald).
---------------------------------------
0 - No matter what you have today, no root or Magisk-only solution or TWRP with Magisk-solution, do ALL the steps..
1 - Make sure you copy the "Magisk_Manager_Ian_install.apk" file and "Multidisabler-g97x_by_Ian.zip" file to your sd-card before you start!
2 - Download latest firmware via Samfirm or Frija or in any way you can, and unpack.
3 - Boot your phone to Download mode (Power+Bixby+VolDown) and remember to have the USB connected to your computer, it won't boot to DL-mode otherwise
4 - Keep autoboot etc in Odin settings, put each file in its place (AP, BL, CSC etc) and _dont_ use HOME_CSC, use CSC-only-file.
5 - After Odin is done, your phone will reboot automatically - let it! It can feel like forever, but let it do its restarts and stuff until you are in system-setup
6 - Do the setup as per usual, CONNECT TO WIFI but you can safely just say Skip on sign in and other stuff
7 - When setup says its all finished and you get to the standard launcher - go into Settings and enable Developer settings
8 - This step IS necessary.. If you don't do this step, you might get in pre-normal rrm state and you will have wait 7 days to try again: Enter Developer settings and look for the "OEM Unlock" switch - if you are rooting for the first time, Enable it. If you already have root since before or unlocked your bootloiader before, just confirm that its Enabled and graded out.
9 - If you already have an unlocked bootloader, skip to step 12. If not, continue with step 10.
10 - IF you never have unlocked your bootloader before, Power off the phone and boot into download mode again. You will see the long press volUp option for unlock bl, do that.
11 - IF you never have unlocked OEM before, boot the phone again, do the setup without signing in etc but connect to wifi, enable dev settings, go into dev settings and check that OEM now is enabled and grayed out.
12 - Reboot the phone in recovery mode (Power+Bixby+VolUp and keep holding until you are in stock recovery. Choose and do a factory reset.
13 - Reboot to bootloader with option in Recovery.
14 - Flash the tar you got (S10x-TWRP+Magisk_fixed_by_Ian.tar I Odin in the AP-slot. DISABLE auto reboot in Odin first!
15 - When the tar has flashed - Do as instructed on the phone, hold Power+VolDown for a few seconds and AS SOON AS THE SCREEN GOES BLACK -> quickly press power+bixby+volUp for a _long_ time, and I mean it can feel as if its a full minute! After a while you will see TWRP starting with its start screen, you can now let go and enter TWRP.
16 - FORMAT data, then WIPE data AND Cache. DO NOT LET IT REBOOT
17 - Flash "Multidisabler-g97x_by_Ian.zip" from SD card
18 - Go back to start screen of TWRP, Choose Reboot, Choose Recovery - YOU MUST ALWAYS CHOOSE REBOOT TO RECOVERY and _NOT_ system!
19 - Let the phone reboot into system, it will do some reboots it self, and again it will feel like it takes FOREVER - Just let it do its thing and DO NOT PRESS ANY KEYS!
20 - When your phone is finally done booting, just do the normal setup/signing for real this time.
21 - When you are done and in system/launcher, install "Magisk_Manager_Ian_install.apk" from SD card and verify that you now have Magisk Manager installed.
22 - Start Magisk Manager and say YES to what it says, it will do some stuff and then say "Rebooting in 5 seconds" - LET IT BOOT AND DO NOT TOUCH ANY KEYS this time either..
23 - Now when booted to system, start Magisk Manager and see that you have all green and its installed.
24 - Now you have root.
** Every time you reboot manually, be prepared to hold Power+Bixby+VolUP until you see the Samsung S10x-logo, then release and let it reboot, you will have root.
** Every time you power off the phone, when you power ON again, hold Power+Bixby+VolUP until you see the Samsung S10x-logo, then release and it will boot with root.
** Every time you want to enter TWRP-recovery, do as above but KEEP HOLDING THE KEYS UNTIL TWRP-start screen shows then release. Remember to choose reboot to recovery afterwards and you will boot with root.
** IF you screw up and forget or miss the key combo, just let it boot to system, immediately when system is up - reboot again and do the key combo and all is fine again.
This is me just trying to get an emergency first aid space, nothing more, I'm NOT trying to take any credits or dismiss Gieti94.
Thanks All
Thanks for this, have been away for a few days and that thread got crowded pretty quickly and I had no idea what was happening. Thank you!
Note the download link. Never use another one, like someone that adds a megalink or alike. The link I have is maintained and only a couple of hours ago for example Ian's updated multidisabler zip was updated. And it might be om copied content to another site.
/P
Good work all, I've been using this method since Saturday thanks to a PM from PiCkLeS and it now works as it should have from the start, no more accidentally trashing my phone ? Thanks to Ian for his work on this, it's greatly appreciated
No custom rom??
Player04 said:
No custom rom??
Click to expand...
Click to collapse
There is none of yet but I heard there may be 1 around the corner.
The multi disabler doesn't work for G975N, the Korean version
Still didn't bought my s10+ but does this new twrp method means we can flash custom roms and kernels when they will start rolling?
You have to press on the 3 buttons on any reboot of the phone even if magisk is installed?
Ok, so i cannot now do anything with my device. Only galaxy s10e screen with yellow triangle. Flashed TWRP then i got into TWRP. Tried to reboot to recovery but it only did reboot to TWRP. Now i cannot get into download mode! Once i keep power, vol down and bixby button, it does nothing. After screen "galaxy s10e" screen the screen goes blank. What to do?
ratosluaf said:
Ok, so i cannot now do anything with my device. Only galaxy s10e screen with yellow triangle. Flashed TWRP then i got into TWRP. Tried to reboot to recovery but it only did reboot to TWRP. Now i cannot get into download mode! Once i keep power, vol down and bixby button, it does nothing. After screen "galaxy s10e" screen the screen goes blank. What to do?
Click to expand...
Click to collapse
Connect usb, press power and volume down until phone reboots and then directly press bixby and volume down to enter download mode. Open odin and flash BL/AP/CP and CSC
NisseGurra said:
Connect usb, press power and volume down until phone reboots and then directly press bixby and volume down to enter download mode. Open odin and flash BL/AP/CP and CSC
Click to expand...
Click to collapse
Btw did you suceed in booting GSI rom? I will get my S10e soon and i am very thrilled for GSI.
sir-harlekin said:
Btw did you suceed in booting GSI rom? I will get my S10e soon and i am very thrilled for GSI.
Click to expand...
Click to collapse
Bit offtopic but check here: https://forum.xda-developers.com/showpost.php?p=79393913&postcount=2
thank you to everyone who got this done!
Unfortunately I got stuck in pre-normal rrm state.
Can I do anything to get out apart from wait 7 days?
shorza said:
Unfortunately I got stuck in pre-normal rrm state.
Can I do anything to get out apart from wait 7 days?
Click to expand...
Click to collapse
Set your date 7 days into the future like the 11th of may for example.
Sent from my SM-G975F using Tapatalk
MRDOCA said:
Set your date 7 days into the future like the 11th of may for example.
Sent from my SM-G975F using Tapatalk
Click to expand...
Click to collapse
I can't believe it was that easy! Thank you.
shorza said:
Unfortunately I got stuck in pre-normal rrm state.
Can I do anything to get out apart from wait 7 days?
Click to expand...
Click to collapse
This thread is a bit outdated. I referr you to this one:
https://forum.xda-developers.com/ga...covery-twrp-3-3-0-galaxy-s10-exynos-t3924856/
If you want new revised instructions, see post #9 in that thread.
/P
PiCkLeS said:
This thread is a bit outdated. I referr you to this one:
https://forum.xda-developers.com/ga...covery-twrp-3-3-0-galaxy-s10-exynos-t3924856/
If you want new revised instructions, see post #9 in that thread.
/P
Click to expand...
Click to collapse
Thank you. Simply changing the date worked for me.
Thanks for the great job
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
It will display the "Samsung Galaxy Tab S6 | Secured By Knox" logo screen for a few seconds, then switch to the blue "Installing System Update" screen (with the android logo). Installing System Update gets to 28% and stops. Then the rotating icon on the android freezes. Then the device reboots and starts all over again.
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Fedge7 said:
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
It will display the "Samsung Galaxy Tab S6 | Secured By Knox" logo screen for a few seconds, then switch to the blue "Installing System Update" screen (with the android logo). Installing System Update gets to 28% and stops. Then the rotating icon on the android freezes. Then the device reboots and starts all over again.
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Click to expand...
Click to collapse
can you shut it down? try volume down and power button ? if it don't shut down, do this soon as it reboots, hold volume up and down and plug in usb cable to desktop/laptop usb port! it will boot into download mode!
N1NJATH3ORY said:
can you shut it down? try volume down and power button ? if it don't shut down, do this soon as it reboots, hold volume up and down and plug in usb cable to desktop/laptop usb port! it will boot into download mode!
Click to expand...
Click to collapse
I can't actually shut it down. If I start holding power+voldown right after it boots, the tablet does reboot before getting stuck at 28%. But it reboots--it doesn't power off.
I tried download mode and that actually seemed to work! Specifically, I left the tablet overnight in the reboot loop until the battery drained. Just now, I held down volup+voldown and plugged it into my laptop. I got the green "Warning/Custom OS" screen and then pressed volup to continue. The tablet rebooted pretty quickly after that (I'm guessing due to low battery) so I didn't get a good look at the download mode options.
Once I'm in download mode, can I factory reset the tablet? I don't need to preserve any data/apps/settings.
Fedge7 said:
I can't actually shut it down. If I start holding power+voldown right after it boots, the tablet does reboot before getting stuck at 28%. But it reboots--it doesn't power off.
I tried download mode and that actually seemed to work! Specifically, I left the tablet overnight in the reboot loop until the battery drained. Just now, I held down volup+voldown and plugged it into my laptop. I got the green "Warning/Custom OS" screen and then pressed volup to continue. The tablet rebooted pretty quickly after that (I'm guessing due to low battery) so I didn't get a good look at the download mode options.
Once I'm in download mode, can I factory reset the tablet? I don't need to preserve any data/apps/settings.
Click to expand...
Click to collapse
You cannot reset the tablet from Download mode afaik- You need to enter Recovery Mode to do that.
You can however, flash stock from Download mode using Odin (3.13.3 is best). If you're not confident with doing that, your best option is Factory Reset in Recovery Mode. Hold Volume Up and Power when the Tablet is booting, let go when you see the Samsung logo. The timing can be tricky, but you should be able to do it. Also, you can force a reboot with Volume Down and Power.
Alternatively, if factory reset doesn't work, since you're completely stock, you will still be covered under warrenty.
bartleby999 said:
your best option is Factory Reset in Recovery Mode. Hold Volume Up and Power when the Tablet is booting, let go when you see the Samsung logo.
Click to expand...
Click to collapse
Thanks for the suggestion. I have tried this many many times. I've tried letting go of the buttons at different times. I've tried holding volup while letting go of power. I've tried this a ton of different ways, and no matter what, the tablet always shows the "Installing system update" screen. Some googling has led me to believe that sometimes, when performing a factory reset, the "Installing system update" screen shows up right before the normal recovery screen. Is it possible that the tablet is trying to get to recovery mode, but can't get past this first step?
Fedge7 said:
Is it possible that the tablet is trying to get to recovery mode, but can't get past this first step?
Click to expand...
Click to collapse
Honestly, I don't know - I'm not an expert but I guess it's possible that the update failed and corrupted both System and Recovery.
You'll be covered under warrenty, so maybe just return the Tablet from where you purchased or direct to Samsung, could take a while given the current situation though I guess. If you have a PC, then I think the best option would be to just flash stock yourself, since that's probably all Samsung will do. Even if that doesn't work you'd still be covered under warrenty, as far as I'm aware attempting to flash stock doesn't trip Knox.
Here is solution to unbrick your device!!!
Fedge7 said:
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
...
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Click to expand...
Click to collapse
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
FYI, I got in this situation, and the previous post did work for me, just takes good timing! Thanks!!!!
Same issue today for me. My tablet showed different screen with green and red text, it allowed me to delete app data, then booted into safe mode, then i had to do factory reset and now i am screwed, as it is refusing to restore any apps and their settings. I will try to flash it back to Android 9, maybe then it will do the restore. I forgot to do any manual backup to SD or so.
Edit: the device upgraded to 10, but reset itself after about 10 minutes of use.
Edit2: i found what caused it. It is caused by Nova Launcher, if i try to set wallpaper.
Just found a news article that there is a RGB/sRGB problem with wallpapers. It might be the problem i had.
I am adding a screenshot of the result.
Yeah, I had that kind of reboot loop from a wallpaper that I downloaded
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Bravo!!
Works for me.
Many thanks
I can get into download mode. But it kicks me out within a few seconds. Any help please
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Hi,
Really need your help, after I updated my firmware using Odin, updated BL, AP, CP, CSC, my tab cannot boot up stuck in logo. Doing the Power + volume up leads me to different screen now. I cannot access recovery mode or download page anymore,
What must I do? Pleasssee help. Added the pic, after doing hard reset (power + vol up)
I cannot connect back to Odin also. Always setup connection failed.
Please help. Really messed up big time
Just a thought... Can this be restored from service center?
Thank you in advance.
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Genpis said:
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Click to expand...
Click to collapse
Did you use HOME CSC or the non HOME CSC when flashing?
Genpis said:
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Click to expand...
Click to collapse
Try to install a castom rooted rom which has pre installed also Twrp.
[MAGISK Rom / Firmware base convertor) 420rom-T860/5 - V13.3- CUE1 - ANDROID 10 - OneUI 3.1 - Sec Patch 05/2021 - Released 06/07/2021
WELCOME TO 420 ROM - MAGISK ROM FOR SAMSUNG GALAXY TAB S6 WiFi/4G (T860/5)! 420rom Telegram-Group: Please bear in mind that things will be added as and when my learning and time permits (being a dad with a family and having ADHD myself means...
forum.xda-developers.com
Download the android 11 last rooted rom from there. You install it with odin as as a normal original rom.
Disable in odin auto reboot. After rom install, restart manually and press the correct buttons immediately to boot in Twrp and not to system. Format (not wipe) data from there and reboot to system. If you are lucky it will work..
(I hope you unlocked bootloader before try to root. If you haven't unlocked bootloader this won't work also).
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Why flashing only the bootloader first? At the moment I'm trying to recover my s20 fe from a bootloop without losing my data
sosimple said:
Try to install a castom rooted rom which has pre installed also Twrp.
[MAGISK Rom / Firmware base convertor) 420rom-T860/5 - V13.3- CUE1 - ANDROID 10 - OneUI 3.1 - Sec Patch 05/2021 - Released 06/07/2021
WELCOME TO 420 ROM - MAGISK ROM FOR SAMSUNG GALAXY TAB S6 WiFi/4G (T860/5)! 420rom Telegram-Group: Please bear in mind that things will be added as and when my learning and time permits (being a dad with a family and having ADHD myself means...
forum.xda-developers.com
Download the android 11 last rooted rom from there. You install it with odin as as a normal original rom.
Disable in odin auto reboot. After rom install, restart manually and press the correct buttons immediately to boot in Twrp and not to system. Format (not wipe) data from there and reboot to system. If you are lucky it will work..
(I hope you unlocked bootloader before try to root. If you haven't unlocked bootloader this won't work also).
Click to expand...
Click to collapse
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
jointer said:
Same issue today for me. My tablet showed different screen with green and red text, it allowed me to delete app data, then booted into safe mode, then i had to do factory reset and now i am screwed, as it is refusing to restore any apps and their settings. I will try to flash it back to Android 9, maybe then it will do the restore. I forgot to do any manual backup to SD or so.
Edit: the device upgraded to 10, but reset itself after about 10 minutes of use.
Edit2: i found what caused it. It is caused by Nova Launcher, if i try to set wallpaper.
Click to expand...
Click to collapse
did you managed to not lose your data?
jrdef said:
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
Click to expand...
Click to collapse
Wiping cache partition in Recovery and reflashing the firmware are basically your only 2 options
jrdef said:
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
Click to expand...
Click to collapse
Flash in odin the same rom you had. There are 2 csc files in rom, which you use 1 in odin one. Try use the "home csc". Home csc keep KEEPS your data. If you're lucky it may work. (It would work in keeping your data 100% if your rom was ok. Because it isn't you have some changes to work.).
You must try with same rom or newer.
CSC – If you flash the CSC file, it’ll perform a factory reset of your Galaxy device and wipe all data while installing a new firmware to bring your device to the same state as it was when you purchased it. Go with CSC if you want a clean installation.
HOME_CSC – On the other hand, if you want to keep your Samsung phone’s data and settings even flashing the stock firmware, you can select the HOME_CSC file.