Hello xda,
are new to the community.
Recently I purchased a goophone from aliexpress.
This goophone I was sold as a quad core with 2GB of RAM and 32GB of internal memory.
I realized it was a fake quad core not appela I connected it to "droid mtk tool" for windows and found to be a dual core.
I was trying to install a new ROM, but accidentally while flash tool loaded after disconnecting the USB cable.
From that moment the phone is dead.
Will not turn on, do not charge more and not more signs of life with usb.
Please help me to solve the problem.
I am an electronics engineer and I have no problems to remove it.
I would then collect all the details obtained from this tread to create a guide to avoid new similar tread.
HELP ME! :crying:
PS: My phone only has a sensor near the front speaker.
Sorry for my bad English, I'm Italian.
sp-one said:
Hello xda,
are new to the community.
Recently I purchased a goophone from aliexpress.
This goophone I was sold as a quad core with 2GB of RAM and 32GB of internal memory.
I realized it was a fake quad core not appela I connected it to "droid mtk tool" for windows and found to be a dual core.
I was trying to install a new ROM, but accidentally while flash tool loaded after disconnecting the USB cable.
From that moment the phone is dead.
Will not turn on, do not charge more and not more signs of life with usb.
Please help me to solve the problem.
I am an electronics engineer and I have no problems to remove it.
I would then collect all the details obtained from this tread to create a guide to avoid new similar tread.
HELP ME! :crying:
PS: My phone only has a sensor near the front speaker.
Sorry for my bad English, I'm Italian.
Click to expand...
Click to collapse
UP
sp-one said:
Hello xda,
are new to the community.
Recently I purchased a goophone from aliexpress.
This goophone I was sold as a quad core with 2GB of RAM and 32GB of internal memory.
I realized it was a fake quad core not appela I connected it to "droid mtk tool" for windows and found to be a dual core.
I was trying to install a new ROM, but accidentally while flash tool loaded after disconnecting the USB cable.
From that moment the phone is dead.
Will not turn on, do not charge more and not more signs of life with usb.
Please help me to solve the problem.
I am an electronics engineer and I have no problems to remove it.
I would then collect all the details obtained from this tread to create a guide to avoid new similar tread.
HELP ME! :crying:
PS: My phone only has a sensor near the front speaker.
Sorry for my bad English, I'm Italian.
Click to expand...
Click to collapse
hi
any luck with fixing the phone?
please confirm and provide links or guide which you followed to fix the problem.
thanks
netvpn7 said:
hi
any luck with fixing the phone?
please confirm and provide links or guide which you followed to fix the problem.
thanks
Click to expand...
Click to collapse
Hi @netvpn7 , thank you for inviting me. I have not yet solved the problem, but I disassembled the phone and I found the test point. by connecting the TP with GND, I managed a distant spot the phone to the pc but can't get a flashing the ROM because there is the preloader. What's not so fare, please, help me! :'(
sp-one said:
Hello xda,
are new to the community.
Recently I purchased a goophone from aliexpress.
This goophone I was sold as a quad core with 2GB of RAM and 32GB of internal memory.
I realized it was a fake quad core not appela I connected it to "droid mtk tool" for windows and found to be a dual core.
I was trying to install a new ROM, but accidentally while flash tool loaded after disconnecting the USB cable.
From that moment the phone is dead.
Will not turn on, do not charge more and not more signs of life with usb.
Please help me to solve the problem.
I am an electronics engineer and I have no problems to remove it.
I would then collect all the details obtained from this tread to create a guide to avoid new similar tread.
HELP ME! :crying:
PS: My phone only has a sensor near the front speaker.
Sorry for my bad English, I'm Italian.
Click to expand...
Click to collapse
Did you make a back up with SP flash Tool before attempting to flash a new rom? Or do you at least have the stock firmware (Not sure if you are able to download your devices firmware from the manufacturers website, if they have one)
What should I do?
Hello,
I've purchased an fake iphone5 from Aliexpress, and tried the MtkDroidTools introduced on;
http://forum.xda-developers.com/showthread.php?t=2160490
I've succeeded to make back up with this tool .
But when I tried to install CWM with this tool, an error occurred and then my phone is bricked.
I'll attatch the log file of MtkDroidTools.
What should I do to unbrick my phone ?
Please help me !!
androidbbhjp106 said:
Hello,
I've purchased an fake iphone5 from Aliexpress, and tried the MtkDroidTools introduced on;
http://forum.xda-developers.com/showthread.php?t=2160490
I've succeeded to make back up with this tool .
But when I tried to install CWM with this tool, an error occurred and then my phone is bricked.
I'll attatch the log file of MtkDroidTools.
What should I do to unbrick my phone ?
Please help me !!
Click to expand...
Click to collapse
same here my friends.
But I am not sure what went wrong since my whole process according to SP Flashtool went really well.
Now the device is not identified
http://forum.xda-developers.com/showthread.php?t=2737659
Giorgos241 said:
same here my friends.
But I am not sure what went wrong since my whole process according to SP Flashtool went really well.
Now the device is not identified
http://forum.xda-developers.com/showthread.php?t=2737659
Click to expand...
Click to collapse
First sorry for my English because I'm from Spain and I do it with google translation.
I have a clone of the iphone 5s and bought it second hand and the person who sold it to me told me it was a i5s goophone (comes with all the logos and is an exact copy).
As I do not like iOS, I turn to the www.needrom.com page and downloaded firmware to put it as pure android, for which I used the Sp Flash Tool, it ended perfectly with the green symbol, but what was my surprise after I turned off the phone and no longer works.
In windows 7 detects it as me MTK android com port 11, but can not install your backup I made with MtkDroidTools because MtkDroidTools not detected. Same happens with me Sp Flash Tool does not detect it. Windows 7 does not detect it as a phone. I ask for help, and I think he's dead, but not quite, because as I say windows detects something. Before when I had the appearance of IOS 7 and it worked, windows detected it as me YunOsPhone.
thank you very much.
Hi developers...
I bought 2 fake S4 for me and my friend,but after i tried to repartition mine it did not boots any more.
When it was working i had tried some benchmarks and the processor it was identified as an mtk6589,but after i tried to load a new rom ,with sp flash tool,i got a message that i try to load a 5689 rom to a 5677 interface
postimg.org/image/7peo0alrx/
I reinstall the drivers but the problem remains the same.
Whit same 6577 roms the flashing starts but most of the times it stops at the middle.
Now the phone is completly dead and i can't even start the factory mode.
model gt-i9500
fcc id a3lgti9500
ssn -i9500gsmh
3.8v 1300mA
made in corea by samsung
postimg.org/image/6yjz2os85/
dhgate.com/product/s4-5inch-i9500-1-1-mtk6589-quad-core-phones/170588690.html#myaccount_orderdetail-1-null
What is the procedure that i have to follow?Do i have to flash first the preloader??
What rom i have to use??
Thanks in advance
No asnwer...
mvardakis said:
No asnwer...
Click to expand...
Click to collapse
if your phone bricked, how about your friend's phone ?
if your friend's phone no bricked connect to pc and open mtkdroid tools http://forum.xda-developers.com/showpost.php?p=48694347&postcount=852
and upload the screenshot info was given by mtkdroid tool.
because mtkdroid tool will given accurate info
My chinese phone Galaxy GT-N9000 clone Mtk6572 was brick, i try almost every tutorial and rom from many forum but still i can't bring my phone back to life ... please there anyone can help me? :crying: :crying: :crying: :crying:
Korean Clone Version Note 3
ijal7785 said:
My chinese phone Galaxy GT-N9000 clone Mtk6572 was brick, i try almost every tutorial and rom from many forum but still i can't bring my phone back to life ... please there anyone can help me? :crying: :crying: :crying: :crying:
Click to expand...
Click to collapse
- Mine is N9000 Note 3 Korean Clone Version MTK6572, and i'm wondering if theres a way to root it. i know there's a lot of android professionals here, and i hope we can find some answers.
- Version 4.3 jellybean
- Baseband Version: MTK6572 MAUI.11AMD.WW1150.SP. V23
- Kernel 2.6.35.7 [email protected] #4
- Software Version: JSS15J.N900ZSUBMI5
- Hardware Version: 1.1.0
Base on CPU Identifier:
- Spreadtrum SC6820a 1000 Mhz
- (fingerprint Brand for Fake Samsung Market)
- SMDK4X12
- Mali-300
Answer
ijal7785 said:
My chinese phone Galaxy GT-N9000 clone Mtk6572 was brick, i try almost every tutorial and rom from many forum but still i can't bring my phone back to life ... please there anyone can help me? :crying: :crying: :crying: :crying:
Click to expand...
Click to collapse
There is no support for chinese devices anywhere.
The tutorials are made only for the original device.
Did you back up the stock rom in the first place?
This problem would have been solved if you had a backup of your stock rom.
Now you have no other go than to contact the manufacturer for getting the phone fixed.
Trying other roms will not help you in restoring.
ijal7785 said:
My chinese phone Galaxy GT-N9000 clone Mtk6572 was brick, i try almost every tutorial and rom from many forum but still i can't bring my phone back to life ... please there anyone can help me? :crying: :crying: :crying: :crying:
Click to expand...
Click to collapse
try this >
- install ABD Drivers MTK65xx on your pc
- install SP Flash Tools
- download a custom ROM from needrom BUT only for your model N9000, other ROM will be useless
now extract the new ROM and let the window open after extraction
- open SP Flash Tools and load the scatter img file ( is in the extracted folder, navigate to that folder and load the scatter text img file )
- turn your phone off, wait until it vibrates to be sure is off
- press Download button on SP Flash Tools and after 1 sec connect your phone to PC
you'll the Flashing process Start, wait until is finish, it may take more than 10 min in some cases... you'll see a green circle after the process is done
- disconnect your phone and Power On, Voilaa
NovelCaidy said:
- Mine is N9000 Note 3 Korean Clone Version MTK6572, and i'm wondering if theres a way to root it. i know there's a lot of android professionals here, and i hope we can find some answers.
Click to expand...
Click to collapse
use Shuame or Framaroot, if u need help, i'm here...
Guys anybody got a rom for thje same phone...I have it too and its bricked..nothing is working
Ahh!!
Today I faced Same Problem With Same Model But Lots Of Effort Finally I Have Done .
My Working ROM : https://drive.google.com/uc?id=0B35LZs4cp74ZYlRYUnhpejUyZFE
Regards,
filip_pine said:
try this >
- install ABD Drivers MTK65xx on your pc
- install SP Flash Tools
- download a custom ROM from needrom BUT only for your model N9000, other ROM will be useless
now extract the new ROM and let the window open after extraction
- open SP Flash Tools and load the scatter img file ( is in the extracted folder, navigate to that folder and load the scatter text img file )
- turn your phone off, wait until it vibrates to be sure is off
- press Download button on SP Flash Tools and after 1 sec connect your phone to PC
you'll the Flashing process Start, wait until is finish, it may take more than 10 min in some cases... you'll see a green circle after the process is done
- disconnect your phone and Power On, Voilaa
use Shuame or Framaroot, if u need help, i'm here...
Click to expand...
Click to collapse
Hi, thanks for your help, but the phone is still bricked.
When i try to switch power on, nothing happen :crying:
If i push volume button, up or down i can see appear and disappear on device manager the ALCATEL SINGLE RNDIS SINGLE INTERFACE #5 but never MT65xx Preloader driver. :crying:
Seems to be not full dead but i don't know what else i can do.
If you have an advice for us with bricked phone...will be much appreciated.
Very thank you for any help kind. :crying:
D4N13L0N3 said:
Hi, thanks for your help, but the phone is still bricked.
When i try to switch power on, nothing happen :crying:
If i push volume button, up or down i can see appear and disappear on device manager the ALCATEL SINGLE RNDIS SINGLE INTERFACE #5 but never MT65xx Preloader driver. :crying:
Seems to be not full dead but i don't know what else i can do.
If you have an advice for us with bricked phone...will be much appreciated.
Very thank you for any help kind. :crying:
Click to expand...
Click to collapse
you need to install proper driver in order for the PC to recognize the phone, ussualy the Preloader USB VCOM Driver does the job, sometime it takes much more effort, and ADB Drivers need to be installed...
- Proper way to install Preloader USB VCOM Driver -
Connect your phone to PC and wait for the New hardware Found wizzard to appear
Choose i will install the driver by myself, then navigate to the folder location were you have the .ini driver file...
- If the method above dont work, then connect your phone to PC, wait for the New hardware found to appear...
Then right click on My PC and go to the Device Manager
Here you should have a yellow Mark and a phone name or something like this
Right click and choose update driver
Now choose the folder where you have extract the .ini driver file ....
Restart your PC
Open SP FlashTools and be sure that u have the proper ROM for your Phone, otherwise you´ll face DRAM FAIL Error
try this ROM that the guy posted above...
https://drive.google.com/uc?id=0B35LZs4cp74ZYlRYUnhpejUyZFE
filip_pine said:
you need to install proper driver in order for the PC to recognize the phone, ussualy the Preloader USB VCOM Driver does the job, sometime it takes much more effort, and ADB Drivers need to be installed...
- Proper way to install Preloader USB VCOM Driver -
Connect your phone to PC and wait for the New hardware Found wizzard to appear
Choose i will install the driver by myself, then navigate to the folder location were you have the .ini driver file...
- If the method above dont work, then connect your phone to PC, wait for the New hardware found to appear...
Then right click on My PC and go to the Device Manager
Here you should have a yellow Mark and a phone name or something like this
Right click and choose update driver
Now choose the folder where you have extract the .ini driver file ....
Restart your PC
Open SP FlashTools and be sure that u have the proper ROM for your Phone, otherwise you´ll face DRAM FAIL Error
try this ROM that the guy posted above...
Click to expand...
Click to collapse
Thanks, i tried your guide, but with that ROM finaly appear 100% in red color, probably because this phone have MTK6582 and not 6572.
If i use a rom for 6582 at the end of process i can see the DRAM FAIL error
I use this link from XDA for that ROMs:
androidxda.com/download-hdc-stock-rom-models
Any other advice ????
Thanks
D4N13L0N3 said:
Thanks, i tried your guide, but with that ROM finaly appear 100% in red color, probably because this phone have MTK6582 and not 6572.
If i use a rom for 6582 at the end of process i can see the DRAM FAIL error
I use this link from XDA for that ROMs:
androidxda.com/download-hdc-stock-rom-models
Any other advice ????
Thanks
Click to expand...
Click to collapse
ok, take your battery out and tell me the exact model...
filip_pine said:
ok, take your battery out and tell me the exact model...
Click to expand...
Click to collapse
Model: SM-N9000
SSN : N9000GSMH
Made in Korea by Samsung
filip_pine said:
ok, take your battery out and tell me the exact model...
Click to expand...
Click to collapse
This is model:
D4N13L0N3 said:
This is model:
Click to expand...
Click to collapse
try this ROM´s... maybe one of them will make your phone alive ...
http://www.needrom.com/mobile/11-hdc-n9000-note-3/
http://www.needrom.com/mobile/hdc-note-3-mt6582-sm-n9006/
http://www.needrom.com/mobile/hdc-galaxy-note-3-mtk6582-1gb-4gb-2014-kernel/
filip_pine said:
try this ROM´s... maybe one of them will make your phone alive ...
Click to expand...
Click to collapse
Thanks.
I will try, then i tell you if i can use like a paper block
filip_pine said:
try this ROM´s... maybe one of them will make your phone alive ...
Click to expand...
Click to collapse
Nothing, or i mistake all and fail, or i miss some important step.
In attached the errors :
D4N13L0N3 said:
Nothing, or i mistake all and fail, or i miss some important step.
In attached the errors :
Click to expand...
Click to collapse
did u get this error on all the 3 ROM´s ? (((
is there any chance that u can contact your seller from where did you bought the phone ? ask him for the Original ROM...
filip_pine said:
did u get this error on all the 3 ROM´s ? (((
is there any chance that u can contact your seller from where did you bought the phone ? ask him for the Original ROM...
Click to expand...
Click to collapse
No, not all, but everyone go on 100% with red line and not green circle.
I don't understand what error i made.
I think one thing, but the AGENT is right MTK_AllOne_DA.bin or i need to use the one in FIRMWARE folder ??
The files are :
lk.bin
logo.bin
preloader_lcsh82_wet_jb5.bin
What do you thing about it ???
Hi Filip,
i tried to delete USB drivers with USB Deview, after that, i re-charge a new one driver of device and then charge the ROM, this is the result :
The second image appear after about 15 minutes of time out.
D4N13L0N3 said:
Hi Filip,
i tried to delete USB drivers with USB Deview, after that, i re-charge a new one driver of device and then charge the ROM, this is the result :
The second image appear after about 15 minutes of time out.
Click to expand...
Click to collapse
ok, it seems that the problems are not the driver, sience you manage to get the phone recognized by pc... the problem seems to be SP Flash Tool...
my advice would be : reinstall again the windows, install again the USB Preloader VCOM Driver ( the correct way ) and install latest version of SP Flash Tool....
Then try to install again one of the 3 ROM´s that i give you... maybe you have luck buddy, i dont know...
is the only way you could get back your phone.... as you know, these phones are clones and is very hard to find compatible ROM´s and replacements parts....
I was having the ghost touches on my SM-N900 Note 3 Clone and the only solution was to change the digitizer, but : i can´t change it, sience i dont find anywhere Note 3 Clone digitizer replacements... only solution was to put the phone in a box and dont use it... ((
filip_pine said:
my advice would be : reinstall again the windows, install again the USB Preloader VCOM Driver ( the correct way ) and install latest version of SP Flash Tool....
Click to expand...
Click to collapse
I tried on my laptop with new OS installed and no antivirus installed, but the problem is the same.
I tried this tools : SP_Flash_Tool_v5.1352.01
and this : SP Flash Tool v3.1332.0.187
and the tools inside the ROM folder, but nothing. :crying:
Could you link me please the USB Preloader VCOM Driver ( for win7 64bit ), i guess the problem is that i used the bad one
Very thank you again for your help. :good:
Hello,
sorry for bad english, yesterday i tried to upgrade rom in my star n9500 mtk 6589 4gb hd 1280x720 and i put cwm recowery by mtk droid tools and downloaded rom from need room put it to sd card and soft brick stock on logo android i dont make any backup now i got more problem becouse tel wont start i use sp mdt flash and iv got brick... when i connect to usb its reconising aka mtk usb vcom port. Guys what can i do to bring life to my smartphone.
nurek20 said:
Hello,
sorry for bad english, yesterday i tried to upgrade rom in my star n9500 mtk 6589 4gb hd 1280x720 and i put cwm recowery by mtk droid tools and downloaded rom from need room put it to sd card and soft brick stock on logo android i dont make any backup now i got more problem becouse tel wont start i use sp mdt flash and iv got brick... when i connect to usb its reconising aka mtk usb vcom port. Guys what can i do to bring life to my smartphone.
Click to expand...
Click to collapse
Try to find a tool and flash the stock ROM back onto it. Get your hands on the stock ROM and if you can go into CWM then install the zip from there else use some tool to flash it from your computer.
Good luck!
Hit the thanks button if it helped! :laugh:
Im thinking about where i can found the oryginal rom, seller ? A the moment i cant go in CWM its only black screen when i press on button nothing happend ;/ Any sugesstion ?
Star n9500 unbricked!
Hi! I succesfully unbricked today my star n9500.
After trying to use thousands of roms, adb, fastboot, flashtool...etc
I used SP_Flash_Tool_5.1343.01 (as admin). The option was firmware update and without battery. The drivers were cdc-acm (manual instalation). And the only rom that worked for me (android 4.2.2) was N9500-6582-20131122_e2106_v82_jbaolg from needrom.
I have de 8gb ROM version.:good:
I have one bricked (stuck on recovery Mode) Lenovo Ideatab A1000L_F and one perfectly running same tab. i want to create rom backup from perfectly running one to flash it on bricked one using SPFT, but when i connect the working tab with MTK Droid Tools, it says MTK 8317 Hardware is FAKE!!!
Plz help me how can i take backup of rom to flash it on bricked tab....
Did you modify the hardware or edit build.prop?
Sent from my KFSOWI using Tapatalk
Whaaaat??
Resolved, but another problem
now i have gone through with my previous problem, after taking backup with MTK Droid Tools, now i want to flash it using SP Flash Tool, but the scatter is not loading.. it is giving this error... "the region begin address of one load region is not ascending sorting sequence !" what to do?
Spoofed Hardware
danishiqbal said:
I have one bricked (stuck on recovery Mode) Lenovo Ideatab A1000L_F and one perfectly running same tab. i want to create rom backup from perfectly running one to flash it on bricked one using SPFT, but when i connect the working tab with MTK Droid Tools, it says MTK 8317 Hardware is FAKE!!!
Plz help me how can i take backup of rom to flash it on bricked tab....
Click to expand...
Click to collapse
Often unscrupulous manufacturers will fake the CPU version on the phone. Making it show MTK6589, or MTK6592, when in reality the phone is a MTK6577 or MTK6575. MTK Droid Tools will tell you in the front page your phone's true SoC. It will also tell you your phone's LCD driver IC and uboot build V, as well as common information such as baseband version and kernel version.