Related
I have somehow messed up my folio 100, and its BCT and bootloader information.
So im hoping someone else with little experience, knows how to use the nvflash utilities and dump the information for me and send me a link on where to get it.
the combo to get into bootloader mode is: POWER button pressed 4 times + VOL- key and it will go into bootloader mode.
I can extract these tomorrow evening.
Can you be clearer with the bootload sequence?
Tried to get the booload seq. Ended up with a partial reset of settings...
tshoulihane said:
I can extract these tomorrow evening.
Can you be clearer with the bootload sequence?
Tried to get the booload seq. Ended up with a partial reset of settings...
Click to expand...
Click to collapse
well, i dont think you should try it..!!
another user did, he ended up with a semi-bricked device too.. so thanks but now the fun stops.. it seems that Toshiba included a very,very bad key combo that terminates the device to a deadlocked machine..
so ill just figure out another way to get the partitions off it.. but my 4xpower + vol- is really scary, do NOT try it
at least until is cleared on how to get out of this bootloader state again.
I dumped the partitions which are visible from android already. Don't quite know what got resentment with your key sequence - DATA wiped? Some of the preloaded apps are broken now, but they were a bit broken before.
tshoulihane said:
I dumped the partitions which are visible from android already. Don't quite know what got resentment with your key sequence - DATA wiped? Some of the preloaded apps are broken now, but they were a bit broken before.
Click to expand...
Click to collapse
so you mean, you can extract all partitions from a shell?
ie. bootloader of partition2 and so forward?
i didnt notice that all 8 partitions were accessable there?
can you upload the dump of them somewhere?
A guy made the dumps of the ROM (not the recovery image though) on the forum of Frandroid DOT fr but I cannot post you the link directly here (anti spam as I do not have many messages on the forum).
I will PM you (if it allows me)
bootoo said:
A guy made the dumps of the ROM (not the recovery image though) on the forum of Frandroid DOT fr but I cannot post you the link directly here (anti spam as I do not have many messages on the forum).
I will PM you (if it allows me)
Click to expand...
Click to collapse
i have the dump of the /system i need all of the other partitions ie. 0 to 8
i cannot restore system, as i got no bootable tablet at all, i need raw partition dumps which i hope can be used using nvflash
Is it possible to extract opera mobile 10.1 apk?
toca79 said:
Is it possible to extract opera mobile 10.1 apk?
Click to expand...
Click to collapse
look for it here
Dexter_nlb said:
look for it here
Click to expand...
Click to collapse
Thx a lot found it.
I think the resolution is too high though.
Hi Dex, did you was able to restore your bricked folio?
roglio said:
Hi Dex, did you was able to restore your bricked folio?
Click to expand...
Click to collapse
decided to get another one..
ok!
I was hoping you did it because I'm a little tired of android (apple fan ).
My idea was to build and flash linux (ubuntu 10.10 works on toshiba AC100).
But if there isn't a way to restore the factory default (bootloader, etc.), I'll give up.
roglio said:
My idea was to build and flash linux (ubuntu 10.10 works on toshiba AC100).
Click to expand...
Click to collapse
when i was debugging bootloader configs, i was provided some config files that Ac100 users said would work on our folio, but i see now partition setup is very different, so we need to make proper configs for our folio before experimenting with the bootloader..
again, as you metion backup seems to do , when recover seems unavailable currently. it will be hard to verify if the parition table layout is working.
Hi,
sorry, maybe I missunderstood someting, but I cannot understand your problem in reading out the whole flash.
1. I have opened / disassembled my Filio 100. And like I have suspected there is a 16GB micoSD card connected (soldered) to the PCB and fixed with glue. One could read out the whole flash in a card reader.
2. You have fully access to the microSD card out of Android:
/dev/block/mmcblk0
sh-4.1# cd /dev/block
cd /dev/block
sh-4.1# pwd
pwd
/dev/block
sh-4.1# ls -l
ls -l
brw------- root root 254, 1 2010-12-07 08:46 dm-1
brw------- root root 254, 0 2010-12-07 08:46 dm-0
drwxr-xr-x root root 2010-12-07 08:45 vold
brw------- root root 179, 17 2010-12-07 08:45 mmcblk1p1
brw------- root root 179, 16 2010-12-07 08:45 mmcblk1
brw------- root root 7, 7 2010-12-07 08:45 loop7
brw------- root root 7, 6 2010-12-07 08:45 loop6
brw------- root root 7, 5 2010-12-07 08:45 loop5
brw------- root root 7, 4 2010-12-07 08:45 loop4
brw------- root root 7, 3 2010-12-07 08:45 loop3
brw------- root root 7, 2 2010-12-07 08:45 loop2
brw------- root root 7, 1 2010-12-07 08:45 loop1
brw------- root root 7, 0 2010-12-07 08:45 loop0
brw------- root root 179, 8 2010-12-07 08:45 mmcblk0p8
brw------- root root 179, 7 2010-12-07 08:45 mmcblk0p7
brw------- root root 179, 6 2010-12-07 08:45 mmcblk0p6
brw------- root root 179, 5 2010-12-07 08:45 mmcblk0p5
brw------- root root 179, 4 2010-12-07 08:45 mmcblk0p4
brw------- root root 179, 3 2010-12-07 08:45 mmcblk0p3
brw------- root root 179, 2 2010-12-07 08:45 mmcblk0p2
brw------- root root 179, 1 2010-12-07 08:45 mmcblk0p1
brw------- root root 179, 0 2010-12-07 08:45 mmcblk0
sh-4.1#
Regards, Artem
Hi DerArtem! Nice first post indeed!!!!
Thank you for your information.
A micro SD soldered is a nice gift from toshiba!!! This means upgrades, full dumps, etc.
Great
A request: could you please post some pictures?
DerArtem said:
sorry, maybe I missunderstood someting, but I cannot understand your problem in reading out the whole flash.
Click to expand...
Click to collapse
did i write i had problem dumping the entire mmc device? not really.
Yes, you misunderstood,Writing a proper cfg file describing the different areas is required.. dumping is easy part, documenting is harder..
but feel free to contribute and document the .cfg file for bootloader, that is of course appreciated...
I just got back from my business trip, and finally had some more time to take a closer look at the device.
roglio said:
Hi DerArtem! Nice first post indeed!!!!
Thank you for your information.
A micro SD soldered is a nice gift from toshiba!!! This means upgrades, full dumps, etc.
Great
A request: could you please post some pictures?
Click to expand...
Click to collapse
The device has a warranty seal inside. If you open the device completly the seal will break. I have just opened the device soo far, that the seal will not break. To make photos I will have to open it copletly. I will think about it....
Dexter_nlb said:
did i write i had problem dumping the entire mmc device? not really.
Yes, you misunderstood,Writing a proper cfg file describing the different areas is required.. dumping is easy part, documenting is harder..
but feel free to contribute and document the .cfg file for bootloader, that is of course appreciated...
Click to expand...
Click to collapse
Ok, I see. I have duped the mmc and mounted the partitions on my pc:
Here is the partition table on my PC:
Code:
[email protected] ~/bin/folio $ /sbin/fdisk -u -l folio.img
Platte folio.img: 15.9 GByte, 15920005120 Byte
1 Köpfe, 63 Sektoren/Spur, 493551 Zylinder, zusammen 31093760 Sektoren
Einheiten = Sektoren von 1 × 512 = 512 Bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Gerät boot. Anfang Ende Blöcke Id System
folio.img1 2048 526335 262144 83 Linux (/system)
folio.img2 526336 2623487 1048576 83 Linux (/cache)
folio.img3 2623488 2627583 2048 83 Linux (/misc)
folio.img4 2627584 31093759 14233088 5 Erweiterte
folio.img5 2628608 2644991 8192 83 Linux (???)
folio.img6 2646016 4743167 1048576 83 Linux (/data)
folio.img7 4744192 4754431 5120 83 Linux (???)
folio.img8 4755456 31093759 13169152 83 Linux (13G - storage)
Now you can mount the partitions on your pc:
Code:
sudo mount -o loop,ro,offset=$((512*2048)) folio.img /mnt/floppy/
I was not able to find the kernel or the bootloader or the root partition in the dump. I have also checked it with a hex editor.
Is the Folio using an other storage for kernel and bootloder? Does it have more NOR/NAND flash inside?
While looking at the size of the microSD (15920005120 bytes) I think that the bootloader is hiding a part of the microSD from the OS where the kernel and the bootloader are...
Where is the .cfg file you are talking about located?
DerArtem said:
Where is the .cfg file you are talking about located?
Click to expand...
Click to collapse
its a file assoiciated with the nvflash utility. search for the toshiba AC100 or here for more details for them it works fine.
the part 5 and 7 are boot kernel(8Mbyte) + recovery kernel(5Mbyte) , bootloader is as i know from ac100 on part0 , but thats not 100% yet.
Dexter_nlb said:
the part 5 and 7 are boot kernel(8Mbyte) + recovery kernel(5Mbyte) , bootloader is as i know from ac100 on part0 , but thats not 100% yet.
Click to expand...
Click to collapse
So, I have checked part 5 and 7. The content is the same like in boot.img and recovery.img. So the BCT is somewhere else...
Can someone please dump the partition mmcblk0p34 for me?
Command
dd if=/dev/block/mmcblk0p34 of=/sdcard/misc.img
Then upload it to dropbox or something.
Scaryghoul said:
Can someone please dump the partition mmcblk0p34 for me?
Command
dd if=/dev/block/mmcblk0p34 of=/sdcard/misc.img
Then upload it to dropbox or something.
Click to expand...
Click to collapse
Hey guys, someone lend this guy a hand if you can. He has done a lot of great kernel work on the EVO Shift! I'd help you Scary but I don't have a computer here for the next few days. Are you going to be deving for the 3D now?
I'm going to do it right now.
UPDATE: Error, Error Error.....user error I'm sure. I will see about getting this for you before work, but my computer is acting a fool.
lol i just did that for you and was about to post a link to my dropbox and i remembered im unlocked...doh....sorry
ty080279 said:
lol i just did that for you and was about to post a link to my dropbox and i remembered im unlocked...doh....sorry
Click to expand...
Click to collapse
What about S-OFF, is that okay or are you refering to just the HTC Unlock?
I only want an S-ON dump, so you may need temp root to grab what I want.
@Paul - Something like that, but we'll see how things go.
I'm guessing that's my error. I'm not getting full access having S-On, and my bootloader is still locked. I don't trust HTC. I'm not used to not being rooted. I'm not sure how to temp root 1.5, or if we can. I've never done temp root.
PM me. My 3D is still fully stock. If you wanna help a bit I will get it for you.
p34, that's the misc partition isnt it? Are you going to try to edit the mainver in the misc partition and try to downgrade the 1.50 Hboot? If so it doesnt work :-/ both myself and IEF from alpharev tried and it was a no go.. If you know another way, I could do you one better than just the misc partition, I can give you ssh access to my linux box and have a evo 3d hooked up to it that's s-on hboot 1.50 I just need a day or two to get my friend's from him and I can only have it for a day or two but can have it connected to the linux box non stop during that time
graffixnyc said:
p34, that's the misc partition isnt it? Are you going to try to edit the mainver in the misc partition and try to downgrade the 1.50 Hboot? If so it doesnt work :-/ both myself and IEF from alpharev tried and it was a no go.. If you know another way, I could do you one better than just the misc partition, I can give you ssh access to my linux box and have a evo 3d hooked up to it that's s-on hboot 1.50 I just need a day or two to get my friend's from him and I can only have it for a day or two but can have it connected to the linux box non stop during that time
Click to expand...
Click to collapse
Basically exactly what you said, we found that out yesterday for the evo shift as a downgrade option so we could root phones that had the ota. Joeykrim had already told me it wouldn't work on the 3d, but I was still curious what was on the misc partition, I opened up the shift & thunder bolt misc partitions for the older hboot already.
Shift thread, but you already know.
http://forum.xda-developers.com/showthread.php?t=1255474
Hmm, that would be nice but alas, I do not know a better way.
How much do you know about hboot? More specifically, the misc partition's FN0C strings, and the way htc & sprint sign packages, and how hboot verifies the signature.
I'm curious about the 3d's hboot before it's cracked because every single hboot version locked and unlocked has two similar strings. FN0C.
So I'm wondering if these are used in the verification or keys of some sort. For example, in RSA encryption there is public and private keys, public which encrypts and private which decrypts(I may have these backwards as it's been a very long time since I've done any encryption/decryption). So an example of practical use on sprint/htc's part would be encrypting with a key, then hboot decrypting it with FN0C. Although every encryption set of keys need to be related in some way since you can't just decrypt anything with any key. So it'd give a base to try and brute force finding the other key, or give us more information with how hboot works. Brute forcing an RSA key is generally unrealistic because of the sheer amount of time it'd take, but it'd be a fun learning experience messing with hboot.
edit: Well after a long afternoon I found out that sprint/htc takes a zip, takes it's sha256 hash and then encrypts that hash using an RSA private key, then stuffs it in the first 256bytes of the zip. Then when hboot loads it, it shaves off those 256 bytes and attempts to decrypt it using a public key.
Even disassembled hboot(Not using an arm disassembler though, couldn't find one, but an x86 one gave me an interesting output)
Doesn't look like misc has anything to do with the RSA encryption or hoot signatures though.
We did find it funny that out of 4 misc partitions on 3 different phones, FN0C showed up at the EXACT same offset, but it's probably nothing worth looking into.
So to anyone trying to decrypt this or recreate sprint/htc's signature algorithm, good luck.
misc partition
Scaryghoul said:
Can someone please dump the partition mmcblk0p34 for me?
Command
dd if=/dev/block/mmcblk0p34 of=/sdcard/misc.img
Then upload it to dropbox or something.
Click to expand...
Click to collapse
How do you know that's the misc partition ?
I have a HTC EVO 3D GSM version and I don't have that partition :
# ls /dev/block
loop0 loop7 mmcblk0p14 mmcblk0p20 mmcblk0p27 mmcblk0p5 platform
loop1 mmcblk0 mmcblk0p15 mmcblk0p21 mmcblk0p28 mmcblk0p6 vold
loop2 mmcblk0p1 mmcblk0p16 mmcblk0p22 mmcblk0p29 mmcblk0p7 zram0
loop3 mmcblk0p10 mmcblk0p17 mmcblk0p23 mmcblk0p3 mmcblk0p8
loop4 mmcblk0p11 mmcblk0p18 mmcblk0p24 mmcblk0p30 mmcblk0p9
loop5 mmcblk0p12 mmcblk0p19 mmcblk0p25 mmcblk0p31 mmcblk1
loop6 mmcblk0p13 mmcblk0p2 mmcblk0p26 mmcblk0p4 mmcblk1p1
justexpect said:
How do you know that's the misc partition ?
I have a HTC EVO 3D GSM version and I don't have that partition :
# ls /dev/block
loop0 loop7 mmcblk0p14 mmcblk0p20 mmcblk0p27 mmcblk0p5 platform
loop1 mmcblk0 mmcblk0p15 mmcblk0p21 mmcblk0p28 mmcblk0p6 vold
loop2 mmcblk0p1 mmcblk0p16 mmcblk0p22 mmcblk0p29 mmcblk0p7 zram0
loop3 mmcblk0p10 mmcblk0p17 mmcblk0p23 mmcblk0p3 mmcblk0p8
loop4 mmcblk0p11 mmcblk0p18 mmcblk0p24 mmcblk0p30 mmcblk0p9
loop5 mmcblk0p12 mmcblk0p19 mmcblk0p25 mmcblk0p31 mmcblk1
loop6 mmcblk0p13 mmcblk0p2 mmcblk0p26 mmcblk0p4 mmcblk1p1
Click to expand...
Click to collapse
The partitions between the cdma and GSM are different. And this thread is long gone...
Sent from my PG86100 using XDA
I know this thread is very old, But I didn't see the point of making a new one with one different word in the title.
Can someone with an Unlocked CDMA phone upload the misc partition to dropbox. I seem to have either a corrupted or incorrectly formatted partition.
I'm pretty sure its
Code:
/dev/block/mmcblk0p34
Or at least thats what all the errors point me to that.
Code:
E/STT:mtd ( 7738): mtd_open(): cannot find MTD partition [misc]!
D/STT:emmc( 7738): found emmc partition [misc]=[mmcblk0p34]
E/DMAgent ( 7738): the page size is -1, return false
E/DMAgent ( 7738): check_nand_info return abnormal!
E/STT:mtd ( 7768): mtd_open(): cannot find MTD partition [misc]!
D/STT:emmc( 7768): found emmc partition [misc]=[mmcblk0p34]
E/DMAgent ( 7768): the page size is -1, return false
E/DMAgent ( 7768): check_nand_info return abnormal!
This is a port of stock the Nexus7 (Grouper) 4.1.2 ROM with the Nabi 2 OTA 2.4.6 as the base. Everything seems to be working but as the title says it is a beta and so not fully tested....FLASH AT YOUR OWN RISK!!!!
Couple of things to be aware of: You have to update some of the apps before they work (Chrome for instance) and when adjusting the brightness it is possible to turn the screen all the way black, don't panic, just slide it back to the right...oh, and if you try to skip turning on the wifi it still tries to connect but it will eventually time out. If anyone actually uses the Nabi camera I have found that the Nexus 7 Camera app from the play store will work, other ones might also but I tested that one. There are no HDMI settings right now because the Nexus didn't have that port but the HDMI does work.
Screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Instructions:
1. Make a full TWRP backup to external sdcard!!! AND make sure your backup works!!!
2. Download the zip and place it on your external sdcard.
3. Wipe everything except external sdcard.
4. Install the zip.
5. Wipe cache and davlik again for good measure.
6. Reboot and do a little happy dance!!! (First boot takes a while so don't freak after 30 secs, lol)
Download: Nabixus_beta0.1.zip , Mirror1, or Mirror2
MD5: b334707cf14b2ad4e552d6a7a3b48fcd
Let me know what you think, I know there's room for improvement....and I'll fix this post up some at some point, give me a break it's my first time!!
reserved
reserved 2
First! LOL. Glad you got it going. If you need any help or any stock files from my newly acquired Nexus 7, let me know. I can make a complete nandroid if needed.
Additional screenshots!
Can't spend too much time fooling around with it before the kids get up, but looks good for now! Thanks for the awesome work!
Just to report, all is well with the port. Just getting a bit of screen flicker but that is due to the low brightness level. It has gone away since I have raised it up all the way. All apps updating fine via Playstore and OTG USB working great as well. Side loading a lot of what I call my "Power Rooting Apps". This reminds me of the nexus 7 I just got LOL. Great job!
Dude! YOU ROCK....
Now when my son upgrades, I'll be able to use the nabi for kodi (xbmc) on the tv.
Sent from my Nexus 7 using Tapatalk
Awesome, can't wait till I have a moment free to give this a try!
Sent from my Nexus 10 using Tapatalk
@n3wt GREAT job, just wanted to know if I build CyanogenMod for Nexus 7 2012; could you port CyanogenMod over to Nabi?
katinatez said:
@n3wt GREAT job, just wanted to know if I build CyanogenMod for Nexus 7 2012; could you port CyanogenMod over to Nabi?
Click to expand...
Click to collapse
I've been trying to port CM the past few days and keep getting stuck at a never ending boot animation. So yeah, if you guys could give it a shot that would be great, lol.
katinatez said:
if I build CyanogenMod for Nexus 7 2012; could you port CyanogenMod over to Nabi?
Click to expand...
Click to collapse
maybe. aicjofs suggested that the kernel might be too different though. I have a cm with tablet ui for the Nexus that I was looking at but I'm toying with the idea of trying to get a working kernel compiled. ... That way we could just build a rom for the nabi.
It took a lot of hours to get to this point though so whatever comes next will be after a bit of rest.
I'm really happy that you guys are liking this one, feel free to take it and mod it and what not.
SMcC2 said:
I've been trying to port CM the past few days and keep getting stuck at a never ending boot animation. So yeah, if you guys could give it a shot that would be great, lol.
Click to expand...
Click to collapse
Do you have adb working?
ROFL
Anyone else get the email
"Hello from Google: Get the most out of your Nexus 7" ?
n3wt said:
Do you have adb working?
Click to expand...
Click to collapse
I had it working at one point, but don't remember how I had gotten there.
I've been using these links as resources:
How to Build CyanogenMod for Grouper
How to Port CyanogenMod to new Devices
Kernel Building for CyanogenMod
The instructions for building on Grouper say to pull the proprietary blobs from a device with CyanogenMod already installed. I don't have that option.
Note:
Your device should already be running a build of CyanogenMod for the branch you wish to build for the extract-files.sh script to function properly. Nexus users: While it maybe be tempting to run the script on stock Android, and in fact it may succeed, realize that some of the blobs CyanogenMod uses are modified or otherwise different from stock blobs (e.g. Adreno graphics libraries). Save yourself some trouble and install a copy of CyanogenMod on your device before extracting blobs.
Click to expand...
Click to collapse
The instructions for porting to new devices says
Create extract-files.sh and setup-makefiles.sh scripts to pull those blob files from the device using adb and put them in the right /vendor/ directory. There are plenty of examples available for other devices.
Create an .mk Makefile to copy those files to the $OUT folder during the build process and put them in the right place. Again, use other devices as a guide for what this Makefile should look like. An example filename might be BoardConfigVendor.mk
Make sure that the Makefile you just created is included from your main BoardConfig.mk via a command such as -include vendor/[vendor]/[codename]/BoardConfigVendor.mk. Again, existing devices can illustrate how this is done.
Click to expand...
Click to collapse
I don't think I'm getting everything when I do that and that's where my problem is...
maybe. aicjofs suggested that the kernel might be too different though.
Click to expand...
Click to collapse
The Nabi kernel should be based on AOSP, so that is the best ROM's to work with for best compatibility. AOKP, and CM being there own breed might need some kernel mods. For example on current Qualcomm devices CM is using CAF code and AOSP is using google kernel code. Just an example
Anyone else get the email
Click to expand...
Click to collapse
Could be this in build.prop.
ro.build.fingerprint=google/nakasi/grouper:4.1.2/JZO54K/485486:user/release-keys
or a special bit of code in email program.
Create extract-files.sh and setup-makefiles.sh scripts to pull those blob files from the device using adb and put them in the right /vendor/ directory. There are plenty of examples available for other devices.
Click to expand...
Click to collapse
Yeah you have to do it all manually(make proprietary-files.txt). I did it once but it was all manual, and I could have missed something, it took hours. I also remember having a failure pulling the firmware files in the /vendor directory. You can look at what I did in attached
@n3wt You should write up some of your secret sauce, would help those guys mimic what you did on other ROM's
aicjofs said:
Yeah you have to do it all manually(make proprietary-files.txt). I did it once but it was all manual, and I could have missed something, it took hours. I also remember having a failure pulling the firmware files in the /vendor directory. You can look at what I did in attached
Click to expand...
Click to collapse
I was afraid it might have to be done manually.
SMcC2 said:
I've been trying to port CM the past few days and keep getting stuck at a never ending boot animation. So yeah, if you guys could give it a shot that would be great, lol.
Click to expand...
Click to collapse
Same here LOL. I have been trying to port CleanRom 4.0.0 JB 4.3 from my Nexus 7 but am stuck at the 4 rotating orbs. I have the boot image decompiled and the complete System files from my Nexus 7 if anyone would like to give it a try.
aicjofs said:
@n3wt You should write up some of your secret sauce, would help those guys mimic what you did on other ROM's
Click to expand...
Click to collapse
Yes please, I have dissected the rom to see the differences and have gotten as far as I have so far. It is very time consuming for sure. I have 4.1.2 Modded to the bone at the moment.
In case anyone wants the info:Off my Nexus 7 Running CleanRom 4.0.0 4.3 JB.
Code:
(dev/block/platform/sdhci-tegra.3/by-name)
[email protected]:/ $ cat /proc/partitions
cat /proc/partitions
major minor #blocks name
7 0 2111 loop0
7 1 11466 loop1
7 2 9387 loop2
7 3 4190 loop3
7 4 28098 loop4
7 5 61362 loop5
7 6 8348 loop6
7 7 53046 loop7
179 0 31178752 mmcblk0
179 1 12288 mmcblk0p1
179 2 8192 mmcblk0p2
179 3 665600 mmcblk0p3
179 4 453632 mmcblk0p4
179 5 512 mmcblk0p5
179 6 10240 mmcblk0p6
179 7 5120 mmcblk0p7
179 8 512 mmcblk0p8
179 9 30014464 mmcblk0p9
179 32 2048 mmcblk0boot1
179 16 2048 mmcblk0boot0
254 0 2110 dm-0
254 1 11466 dm-1
254 2 9387 dm-2
254 3 4189 dm-3
254 4 28098 dm-4
254 5 61362 dm-5
254 6 8347 dm-6
254 7 53046 dm-7
7 8 2111 loop8
254 8 2110 dm-8
=============================================
[email protected]:/ $ ls -al /dev/block/platform/sdhci-tegra.3/by-name
ls -al /dev/block/platform/sdhci-tegra.3/by-name
lrwxrwxrwx root root 2014-10-04 12:29 APP -> /dev/block/mmcblk0p3
lrwxrwxrwx root root 2014-10-04 12:29 CAC -> /dev/block/mmcblk0p4
lrwxrwxrwx root root 2014-10-04 12:29 LNX -> /dev/block/mmcblk0p2
lrwxrwxrwx root root 2014-10-04 12:29 MDA -> /dev/block/mmcblk0p8
lrwxrwxrwx root root 2014-10-04 12:29 MSC -> /dev/block/mmcblk0p5
lrwxrwxrwx root root 2014-10-04 12:29 PER -> /dev/block/mmcblk0p7
lrwxrwxrwx root root 2014-10-04 12:29 SOS -> /dev/block/mmcblk0p1
lrwxrwxrwx root root 2014-10-04 12:29 UDA -> /dev/block/mmcblk0p9
lrwxrwxrwx root root 2014-10-04 12:29 USP -> /dev/block/mmcblk0p6
[COLOR=Red]=============================================[/COLOR]
[COLOR=DarkRed][B]( fstab.grouper )[/B][/COLOR]
[COLOR=Red]==================================[/COLOR]
# Android fstab file.
#<src> <mnt_point> <type> <mnt_flags> <fs_mgr_flags>
# The filesystem that contains the filesystem checker binary (typically /system) cannot
# specify MF_CHECK, and must come before any filesystems that do specify MF_CHECK
/dev/block/platform/sdhci-tegra.3/by-name/APP /system ext4 noatime,nodiratime,nodev,noauto_da_alloc wait
/dev/block/platform/sdhci-tegra.3/by-name/CAC /cache ext4 noatime,nodiratime,nosuid,nodev,data=writeback,noauto_da_alloc,nomblk_io_submit,errors=panic wait
/dev/block/platform/sdhci-tegra.3/by-name/UDA /data ext4 noatime,nodiratime,nosuid,nodev,data=writeback,noauto_da_alloc,nomblk_io_submit,errors=panic wait,encryptable=/dev/block/platform/sdhci-tegra.3/by-name/MDA
/dev/block/platform/sdhci-tegra.3/by-name/MSC /misc emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/LNX /boot emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/SOS /recovery emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/USP /staging emmc defaults defaults
/devices/platform/tegra-ehci /storage/usbdisk vfat defaults voldmanaged=usbdisk:auto
[COLOR=Red]---------------------------------------------[/COLOR]
[B][COLOR=DarkRed]( fstab.grouper~ )[/COLOR][/B]
[COLOR=Red]-------------------------------------[/COLOR]
# Android fstab file.
#<src> <mnt_point> <type> <mnt_flags> <fs_mgr_flags>
# The filesystem that contains the filesystem checker binary (typically /system) cannot
# specify MF_CHECK, and must come before any filesystems that do specify MF_CHECK
/dev/block/platform/sdhci-tegra.3/by-name/APP /system ext4 ro wait
/dev/block/platform/sdhci-tegra.3/by-name/CAC /cache ext4 noatime,nosuid,nodev,nomblk_io_submit,errors=panic wait
/dev/block/platform/sdhci-tegra.3/by-name/UDA /data ext4 noatime,nosuid,nodev,nomblk_io_submit,errors=panic wait,encryptable=/dev/block/platform/sdhci-tegra.3/by-name/MDA
/dev/block/platform/sdhci-tegra.3/by-name/MSC /misc emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/LNX /boot emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/SOS /recovery emmc defaults defaults
/dev/block/platform/sdhci-tegra.3/by-name/USP /staging emmc defaults defaults
/devices/platform/tegra-ehci /storage/usbdisk vfat defaults voldmanaged=usbdisk:auto
SMcC2 said:
I was afraid it might have to be done manually.
Click to expand...
Click to collapse
Well look over the zip I posted maybe it can save some time.
DarkAngel said:
Same here LOL. I have been trying to port CleanRom 4.0.0 JB 4.3
Click to expand...
Click to collapse
Above 4.2 you will need SElinux support in kernel, so I don't 4.3 is going to work.
aicjofs said:
Well look over the zip I posted maybe it can save some time.
Above 4.2 you will need SElinux support in kernel, so I don't 4.3 is going to work.
Click to expand...
Click to collapse
I know but I had to try.
You think I could just ls the vendor file and copy it in to a text file with the right format?
Here is an example from my HTC...
[email protected]:/ $ cd system
[email protected]:/system $ cd vendor
[email protected]:/system/vendor $ ls */*
etc/audio_effects.conf
firmware/acdb.mbn
firmware/apps.mbn
firmware/bcm4335_prepatch.hcd
firmware/dsp1.mbn
firmware/dsp2.mbn
firmware/dsp3.mbn
firmware/efs1.mbn
firmware/efs2.mbn
firmware/efs3.mbn
firmware/htc61.mbn
firmware/htc62.mbn
firmware/htc63.mbn
firmware/htc64.mbn
firmware/htc65.mbn
firmware/htccdma.mbn
firmware/htcnvbak.mbn
firmware/htcrcust.mbn
firmware/htcrfnv.mbn
firmware/htcsmem.mbn
firmware/htcssmem.mbn
keymaster.b00
keymaster.b01
keymaster.b02
keymaster.b03
keymaster.mdt
firmware/mdm_acdb.img
firmware/q6.b00
firmware/q6.b01
firmware/q6.b03
firmware/q6.b04
firmware/q6.b05
firmware/q6.b06
firmware/q6.mdt
firmware/rpm.mbn
firmware/sbl1.mbn
firmware/sbl1_82.mbn
firmware/sbl1_92.mbn
firmware/sbl1_96.mbn
firmware/sbl2.mbn
eglsubAndroid.so
libEGL_adreno.so
libGLESv1_CM_adreno.so
libGLESv2S3D_adreno.so
libGLESv2_adreno.so
libq3dtools_adreno.so
power.msm8960.so
lib/libC2D2.so
lib/libQSEEComAPI.so
lib/libRSDriver_adreno.so
lib/libWVStreamControlAPI_L1.so
lib/libadreno_utils.so
lib/libbt-vendor.so
lib/libc2d30-a3xx.so
lib/libc2d30.so
lib/libgsl.so
lib/libllvm-a3xx.so
lib/libqc-opt.so
lib/librs_adreno.so
lib/librs_adreno_sha1.so
lib/libsc-a3xx.so
lib/libwvm.so
detection
recognition
[email protected]:/system/vendor $
I tried using kingo root, both on the phone and on the computer. I am not sure where to proceed from there. The main reason I want to root is to disable the startup sound, which does not get disabled automatically when I have my phone on mute. I tried using the sound disabler app from the play store, and it seems to not be working (the startup sound still plays).
Rooting Coolpad Canvas (Cricket)
Me too having same issue as well, tried kingoroot
And king-root some got to like 30%... need help rooting it as well.. and maybe twrp would be great
But possibly could flash twrp using the coolpad's
Note 3 twrp for it, because they both have same
Resolution and screen size i believe, so for the porting shouldn't be all that hard.. any advice
Would be great..
Coolpad Canvas Root
joshglen said:
I tried using kingo root, both on the phone and on the computer. I am not sure where to proceed from there. The main reason I want to root is to disable the startup sound, which does not get disabled automatically when I have my phone on mute. I tried using the sound disabler app from the play store, and it seems to not be working (the startup sound still plays).
Click to expand...
Click to collapse
SmartPhoneDeveloper said:
Me too having same issue as well, tried kingoroot
And king-root some got to like 30%... need help rooting it as well.. and maybe twrp would be great
But possibly could flash twrp using the coolpad's
Note 3 twrp for it, because they both have same
Resolution and screen size i believe, so for the porting shouldn't be all that hard.. any advice
Would be great..
Click to expand...
Click to collapse
I just ordered a coolpad canvas its coming on Saturday. I was able to root my last phone (Alcatel Onetouch Flint) which had no official guides on how to root it (so i made a guide). I might be able to do the same thing with this phone ill let u guys know if im able to root it when it comes.
Casey Campanile said:
I just ordered a coolpad canvas its coming on Saturday. I was able to root my last phone (Alcatel Onetouch Flint) which had no official guides on how to root it (so i made a guide). I might be able to do the same thing with this phone ill let u guys know if im able to root it when it comes.
Click to expand...
Click to collapse
Awesome!.. you won't believe how good this phone is for the price it has pretty powerful specs for the price and screen size is a whopping 5.5 inch and HD, I got mine for 49.99 when it was available at walmart luckily they had 2 left in Stock the day I went and got one.. but yeah I been trying to root it with no luck , but I'm not that good at programming when it comes to phones hopefully we can get this one rooted at least if anything .. it definitely deserves it being decently powerful phone here's the specs on it.. : https://ibb.co/ehJjtQ
Guys I was able to pull over 70% of the system files from it.. but for some reason it stops at when trying to pull WCNSS_qcom_cfg.ini file for some reason-(said permission was denied)??..hmm.., I will post pic shortly..
Any luck Casey on it?.. so far nothing working for rooting it yet you may have better luck than me..
SmartPhoneDeveloper said:
Any luck Casey on it?.. so far nothing working for rooting it yet you may have better luck than me..
Click to expand...
Click to collapse
No luck yet I tried kingroot, kingo app, towelroot, framaroot and some others nothing works. Still searching for a better method
So apparently it's harder to root nougat cuz of this new security feature. I feel like one click methods not gonna work
Well I also noticed when doing command get ver all that it said secured eMMc with the little kernel bootloader I'm sure there are ways around this but its going to require some help with someone that has higher phone developing skills than of my own of course.. also try command while connected to computer "adb pull system" without the quotes it got to 72% for me before it wouldn't write no more still have the files for system if anyone needs them for rewriting or porting in the bootloader ..
---------- Post added at 03:55 AM ---------- Previous post was at 03:43 AM ----------
Casey Campanile said:
No luck yet I tried kingroot, kingo app, towelroot, framaroot and some others nothing works. Still searching for a better method
Click to expand...
Click to collapse
Same here.. hmm , well if you or you can invite someone that maybe can port in or rewrite the little kernel bootloader to be unlocked, i have 72% of the system files.. still couldn't Figure out how to or where to extract the boot.img or recovery.img from?.. or the cache.img and the other .img files as well.. some of them or the .sh file in the system folder i extracted i believe may contain the answer?.. I'm sure for the rewriting of the bootloader but it's gonna require someone with better skills than of mine because i don't know how to rewrite little kernel bootloader image, but I'm sure for some this is a breeze though lol...
Oh almost forgot , from the building prop editor, i also managed to get the recovery key ID as well of someone knows how to port or rewrite the recovery.img, i know this will be of big help for sure this is the recovery key ID for the recovery image , i will post the pic of it shortly..
SmartPhoneDeveloper said:
Same here.. hmm , well if you or you can invite someone that maybe can port in or rewrite the little kernel bootloader to be unlocked, i have 72% of the system files.. still couldn't Figure out how to or where to extract the boot.img or recovery.img from?.. or the cache.img and the other .img files as well.. some of them or the .sh file in the system folder i extracted i believe may contain the answer?.. I'm sure for the rewriting of the bootloader but it's gonna require someone with better skills than of mine because i don't know how to rewrite little kernel bootloader image, but I'm sure for some this is a breeze though lol...
Click to expand...
Click to collapse
The mount points for where to pull the .img files from can't you find them by running cat /proc/mounts? These are the locations I got:
Interesting... so with these mount points I'm assuming we should be able to do something I'm sure of it considering the zte zmax pro which also is qualcomm snapdragon processor and also utilizing same procedure of sorts and they managed to make twrp for it and also root so I'm sure same here ...which they some how put it into diagnostic mode or called **DFU mode and it allowed them to flash after mounting points was made with Linux OS
---------- Post added at 02:13 AM ---------- Previous post was at 02:11 AM ----------
Also we you could possibly use also called QPST tool for Windows allows flashing of qualcomm processors as well ...
SmartPhoneDeveloper said:
Interesting... so with these mount points I'm assuming we should be able to do something I'm sure of it considering the zte zmax pro which also is qualcomm snapdragon processor and also utilizing same procedure of sorts and they managed to make twrp for it and also root so I'm sure same here ...which they some how put it into diagnostic mode or called **DFU mode and it allowed them to flash after mounting points was made with Linux OS
---------- Post added at 02:13 AM ---------- Previous post was at 02:11 AM ----------
Also we you could possibly use also called QPST tool for Windows allows flashing of qualcomm processors as well ...
Click to expand...
Click to collapse
Managed to get exact locations of each partition by running cat /proc/partitions and then running df to convert them into the common names. Here's what I got:
cp3636a:/ $ cat /proc/partitions
major minor #blocks name
254 0 524288 zram0
179 0 15267840 mmcblk0
179 1 102400 mmcblk0p1
179 2 1 mmcblk0p2
179 3 8 mmcblk0p3
179 4 512 mmcblk0p4
179 5 512 mmcblk0p5
179 6 512 mmcblk0p6
179 7 512 mmcblk0p7
179 8 2048 mmcblk0p8
179 9 2048 mmcblk0p9
179 10 256 mmcblk0p10
179 11 256 mmcblk0p11
179 12 16384 mmcblk0p12
179 13 2048 mmcblk0p13
179 14 2048 mmcblk0p14
179 15 32 mmcblk0p15
179 16 2048 mmcblk0p16
179 17 16 mmcblk0p17
179 18 4096 mmcblk0p18
179 19 20480 mmcblk0p19
179 20 65536 mmcblk0p20
179 21 3072 mmcblk0p21
179 22 3072 mmcblk0p22
179 23 65536 mmcblk0p23
179 24 65536 mmcblk0p24
179 25 1024 mmcblk0p25
179 26 262144 mmcblk0p26
179 27 32768 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 512 mmcblk0p29
179 30 32 mmcblk0p30
179 31 65536 mmcblk0p31
259 0 32 mmcblk0p32
259 1 1024 mmcblk0p33
259 2 1024 mmcblk0p34
259 3 32768 mmcblk0p35
259 4 512 mmcblk0p36
259 5 4096 mmcblk0p37
259 6 384 mmcblk0p38
259 7 384 mmcblk0p39
259 8 384 mmcblk0p40
259 9 384 mmcblk0p41
259 10 256 mmcblk0p42
259 11 256 mmcblk0p43
259 12 256 mmcblk0p44
259 13 256 mmcblk0p45
259 14 8 mmcblk0p46
259 15 65536 mmcblk0p47
259 16 2928640 mmcblk0p48
259 17 10876911 mmcblk0p49
179 32 4096 mmcblk0rpmb
179 64 7761920 mmcblk1
179 65 16384 mmcblk1p1
179 66 7744495 mmcblk1p2
253 0 2882924 dm-0
253 1 10876895 dm-1
253 2 7744495 dm-2
cp3636a:/ $ df
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 866276 5212 861064 1% /
tmpfs 947448 616 946832 1% /dev
tmpfs 947448 0 947448 0% /mnt
/dev/block/dm-2 7622740 879764 6726592 12% /mnt/expand/ad6a771b-2b4f-4d99-8f6d-640bb1ebd212
/dev/block/dm-0 2792600 2109896 666320 76% /system
/dev/block/bootdevice/by-name/cache 253920 368 248312 1% /cache
/dev/block/bootdevice/by-name/dsp 12016 5052 6640 44% /dsp
/dev/block/bootdevice/by-name/modem 102352 69776 32576 69% /firmware
/dev/block/dm-1 10574084 4527048 6030652 43% /data
/dev/fuse 7622740 879764 6726592 12% /storage/emulated
cp3636a:/ $
---------- Post added at 04:54 PM ---------- Previous post was at 04:50 PM ----------
SmartPhoneDeveloper said:
Interesting... so with these mount points I'm assuming we should be able to do something I'm sure of it considering the zte zmax pro which also is qualcomm snapdragon processor and also utilizing same procedure of sorts and they managed to make twrp for it and also root so I'm sure same here ...which they some how put it into diagnostic mode or called **DFU mode and it allowed them to flash after mounting points was made with Linux OS
---------- Post added at 02:13 AM ---------- Previous post was at 02:11 AM ----------
Also we you could possibly use also called QPST tool for Windows allows flashing of qualcomm processors as well ...
Click to expand...
Click to collapse
So using the location I tried to use the dd command to pull system.img but it said permission denied looks like it requires root:
dd if=/dev/block/dm-0 of=/storage/emulated/0/system.img
dd: /dev/block/dm-0: Permission denied
1|cp3636a:/ $
Don't know a whole lot about development but I'm pretty comfortable with using the Android back end and I'd be willing to help any way I can if there's something I can do or provide. This is such a neat little phone and I think it has a lot of potential.
Picked a canvas up on sale at bestbuy as a back up.. I must say its a nice phone for the money...
Now I just have to wait for coolpad- cricket to release unlock codes so I can use overseas travel.
Try this root
joshglen said:
I tried using kingo root, both on the phone and on the computer. I am not sure where to proceed from there. The main reason I want to root is to disable the startup sound, which does not get disabled automatically when I have my phone on mute. I tried using the sound disabler app from the play store, and it seems to not be working (the startup sound still plays).
Click to expand...
Click to collapse
Hi bro.. Try this root.. I tried in my coolpad canvas cricket but this root is only temporary because I have not found twrp to install super us..
https://forum.xda-developers.com/android/development/guide-to-root-coolpad-note-5-flashing-t3637644
Carzacamil said:
Hi bro.. Try this root.. I tried in my coolpad canvas cricket but this root is only temporary because I have not found twrp to install super us..
https://forum.xda-developers.com/android/development/guide-to-root-coolpad-note-5-flashing-t3637644
Click to expand...
Click to collapse
Here is a link to a TWRP build for the Redmi 4a, same exact internals as our phone. I mean the phones are exact all the way across the board. The best thing to do is to fastboot boot the .img first to see if it works 100%, and being on Nougat flash su systemless root. If it boots to TWRP from fastboot and you can flash su than we should be able to permanently flash TWRP from there. https://forum.xda-developers.com/android/development/recovery-twrp-3-1-0-0-xiaomi-redmi-4a-t3576024
zMILWAUKEE said:
Here is a link to a TWRP build for the Redmi 4a, same exact internals as our phone. I mean the phones are exact all the way across the board. The best thing to do is to fastboot boot the .img first to see if it works 100%, and being on Nougat flash su systemless root. If it boots to TWRP from fastboot and you can flash su than we should be able to permanently flash TWRP from there. https://forum.xda-developers.com/android/development/recovery-twrp-3-1-0-0-xiaomi-redmi-4a-t3576024
Click to expand...
Click to collapse
i tried it but my cellphone is bootloop .. when i do fastboot it says:
Now send the package you want to apply
to the device with "adb sideload <filename>". . .
Finding update package. . .
opening update package. . .
Verifing update package. . .
E:failed to verify whole-file signature
Update package verification took 0.7 s (result 1)
E:signature verification failed
Installation aborted.
Carzacamil said:
i tried it but my cellphone is bootloop .. when i do fastboot it says:
Now send the package you want to apply
to the device with "adb sideload <filename>". . .
Finding update package. . .
opening update package. . .
Verifing update package. . .
E:failed to verify whole-file signature
Update package verification took 0.7 s (result 1)
E:signature verification failed
Installation aborted.
Click to expand...
Click to collapse
From what you're describing it sounds like you didn't do it correctly. In the bootloader it should never ask you to sideload anything. The correct steps are, with the phone on and adb debugging enabled, adb devices, should show your connected to your phone, next adb reboot bootloader, phone will restart into a download type screen, next step, on PC type fastboot devices to see if the PC and phone are communicating correctly, next is to type fastboot boot recovery.img, if it boots into the TWRP we're good, sorry but I don't have a PC up and running right now. So all I can do is suggest and hope you guys can get it running.
Anyone check into this and the comment that's on it, don't know if it will help, but just maybe.
https://mobile.twitter.com/srsroot/status/871056445315452933?lang=en
meatball702 said:
Anyone check into this and the comment that's on it, don't know if it will help, but just maybe.
https://mobile.twitter.com/srsroot/status/871056445315452933?lang=en
Click to expand...
Click to collapse
Don't do it, it's bull crap nothing but viruses. That srs spam link says they can root all phones, well if they could more devs on XDA would push it, but no it's a load of b.s.
follows the link of Stock Moto X4 ROM with Android 7.1.1 and September patch.
Model: X4 (Payton)
Version: NPW26.83-34-0-1
https://rsdsecure-cloud.motorola.co...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
The linked page shows a error, will be better if you can upload the file.
Yeah, link is borked. But I may pull it anyway... will post here if I do.
Had my XT1900-1 (Project Fi) for about an hour before I got bored and the bootloader was unlocked.
Thinking of rooting just to debloat (don't get me started on how bloated the Android One build is)... seems like root will be pretty straightforward given that unlock is painless and partition access seems unrestricted. Haven't tried yet, but thinking that just perms and pushing su might do the trick. Would like to have the device for a couple days before I go that far. [edit: Actually, Magisk looks like a pretty good bet w/o custom recovery... may try that]
Then maybe, if I have time start gathering vendor stuff/blobs/etc and build... something.
Anyone else out there tinkering yet?
mightysween said:
Yeah, link is borked. But I may pull it anyway... will post here if I do.
Had my XT1900-1 (Project Fi) for about an hour before I got bored and the bootloader was unlocked.
Thinking of rooting just to debloat (don't get me started on how bloated the Android One build is)... seems like root will be pretty straightforward given that unlock is painless and partition access seems unrestricted. Haven't tried yet, but thinking that just perms and pushing su might do the trick. Would like to have the device for a couple days before I go that far. [edit: Actually, Magisk looks like a pretty good bet w/o custom recovery... may try that]
Then maybe, if I have time start gathering vendor stuff/blobs/etc and build... something.
Anyone else out there tinkering yet?
Click to expand...
Click to collapse
I heard that the reason for the bloat is due to a huge number of partitions that consume space. As such, debloating may not be as easy as you hoped...
ebrandsberg said:
I heard that the reason for the bloat is due to a huge number of partitions that consume space. As such, debloating may not be as easy as you hoped...
Click to expand...
Click to collapse
Just ran cat /proc/partitions.... dang, you are right
|payton_sprout:/ $ cat /proc/partitions
major minor #blocks name
1 0 8192 ram0
1 1 8192 ram1
1 2 8192 ram2
1 3 8192 ram3
1 4 8192 ram4
1 5 8192 ram5
1 6 8192 ram6
1 7 8192 ram7
1 8 8192 ram8
1 9 8192 ram9
1 10 8192 ram10
1 11 8192 ram11
1 12 8192 ram12
1 13 8192 ram13
1 14 8192 ram14
1 15 8192 ram15
253 0 1048576 zram0
179 0 30535680 mmcblk0
179 1 3584 mmcblk0p1
179 2 3584 mmcblk0p2
179 3 2048 mmcblk0p3
179 4 2048 mmcblk0p4
179 5 512 mmcblk0p5
179 6 512 mmcblk0p6
179 7 512 mmcblk0p7
179 8 512 mmcblk0p8
179 9 128 mmcblk0p9
179 10 128 mmcblk0p10
179 11 512 mmcblk0p11
179 12 512 mmcblk0p12
179 13 1024 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 512 mmcblk0p15
179 16 512 mmcblk0p16
179 17 512 mmcblk0p17
179 18 512 mmcblk0p18
179 19 512 mmcblk0p19
179 20 512 mmcblk0p20
179 21 128 mmcblk0p21
179 22 128 mmcblk0p22
179 23 256 mmcblk0p23
179 24 256 mmcblk0p24
179 25 112640 mmcblk0p25
179 26 112640 mmcblk0p26
179 27 1 mmcblk0p27
179 28 8 mmcblk0p28
179 29 16384 mmcblk0p29
179 30 16384 mmcblk0p30
179 31 1024 mmcblk0p31
259 0 512 mmcblk0p32
259 1 512 mmcblk0p33
259 2 2048 mmcblk0p34
259 3 2048 mmcblk0p35
259 4 6144 mmcblk0p36
259 5 6144 mmcblk0p37
259 6 32768 mmcblk0p38
259 7 512 mmcblk0p39
259 8 128 mmcblk0p40
259 9 16384 mmcblk0p41
259 10 512 mmcblk0p42
259 11 8192 mmcblk0p43
259 12 65536 mmcblk0p44
259 13 65536 mmcblk0p45
259 14 16384 mmcblk0p46
259 15 16384 mmcblk0p47
259 16 1024 mmcblk0p48
259 17 8192 mmcblk0p49
259 18 256 mmcblk0p50
259 19 256 mmcblk0p51
259 20 1 mmcblk0p52
259 21 1 mmcblk0p53
259 22 4608 mmcblk0p54
259 23 4608 mmcblk0p55
259 24 33424 mmcblk0p56
259 25 33424 mmcblk0p57
259 26 64 mmcblk0p58
259 27 64 mmcblk0p59
259 28 8192 mmcblk0p61
259 29 8192 mmcblk0p62
259 30 589824 mmcblk0p63
259 31 589824 mmcblk0p64
259 32 4227072 mmcblk0p65
259 33 4227072 mmcblk0p66
259 34 20262895 mmcblk0p67
179 32 4096 mmcblk0rpmb
252 0 4161104 dm-0
252 1 580580 dm-1
Click to expand...
Click to collapse
---------- Post added at 02:09 PM ---------- Previous post was at 01:56 PM ----------
Looks like the OP file was a leaked Brazilian version of the firmware... wonder if the boot.img is the same as US ?
And also looks like Motorola may be giving each variant of the device its own device name... not sure if this will be good down the line, development-wise, or not:
ro.product.name=payton_fi
ro.product.device=payton_sprout
Click to expand...
Click to collapse
So is it because of project Treble that we have such large system partition. Using 13 GB is too much.
saketkutta said:
So is it because of project Treble that we have such large system partition. Using 13 GB is too much.
Click to expand...
Click to collapse
Is this the partition scheme for Treble? If so, I'm fine with this personally, as it means they have thought ahead to help future-proof the phone (if there is such a thing).
I was seeing users in other threads saying it takes 16-18GB. That's just ridiculous. It should be half that, at most. My brand new install of OS X 10.13 High Sierra doesn't even take up that much space.
crazyates said:
I was seeing users in other threads saying it takes 16-18GB. That's just ridiculous. It should be half that, at most. My brand new install of OS X 10.13 High Sierra doesn't even take up that much space.
Click to expand...
Click to collapse
My custom OS on Nexus 5X took little more than 4 GB. Even if it was project treble (which is not confirmed yet BTW) it should not take more than 9 GB or 10 GB max. Mine out of the box it was 13 GB and something which is ridiculous)
Where did you get the ROM from? Link above is dead?
Iansip said:
Where did you get the ROM from? Link above is dead?
Click to expand...
Click to collapse
I don't think anyone got it here... I saw it bouncing around a couple Brazilian servers, but not open to download. Now that I look, it is the same Build # as the Project Fi version. So, hopefully it will turn up somewhere.
Seems the link in the OP is not dead, just goes to a secure server. It was originally posted on some G+ feeds, but no one has mirrored it yet, apparently
Actually, looks like that whole server is down right now. Every URL returns the same XML error. So maybe it will come back to life soon...
Oh, look at that... Moto has either geo or ISP restrictions on their download! VPN Proxy through server in Los Angeles, and download is running (sloooooowwwly).
Will update tomorrow morning.
UPDATE: Download died at 1.1 GB and the VPN workaround is no longer working. Grrrrr. Could probably extract boot.img anyway, but with no way to check the hash and no images to fall back on, too risky to actually patch/flash it
Got it... well, I have a completed download -- Obviously there is no way to verify the file since I have no MD5/SHA to check against. That said, the archive opens without errors, so I have boot.img now, just not enough stupidity to modify it and flash an unverified firmware back onto a brand new device.
Have a mirror uploading, will share when complete and maybe can get added to the OP.
WARNING: This is unverified fimware for testing/research only. Please don't flash it and then complain when you paperweight your new X4.
UPDATED 10-27-2017: This ZIP has several corrupt files... verify anything against the MD5 in the "flashfile.xml" file before using!
FILE: PAYTON_NPW26.83-34-0-1_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
SIZE: 2702597112 bytes
SHA256 (unverified on the Motorola end!!!): 124f53fef572850532d029d00166829e200b777491502504c9de215fe7dd1046
DOWNLOAD: https://drive.google.com/open?id=0ByZWXbOZqmVqQ09FUXliN3hYMGs
@Anderson_ARS , can you add this to the OP to save people asking the same question over and over and over? Thanks
mightysween said:
Yeah, link is borked. But I may pull it anyway... will post here if I do.
Had my XT1900-1 (Project Fi) for about an hour before I got bored and the bootloader was unlocked.
Thinking of rooting just to debloat (don't get me started on how bloated the Android One build is)... seems like root will be pretty straightforward given that unlock is painless and partition access seems unrestricted. Haven't tried yet, but thinking that just perms and pushing su might do the trick. Would like to have the device for a couple days before I go that far. [edit: Actually, Magisk looks like a pretty good bet w/o custom recovery... may try that]
Then maybe, if I have time start gathering vendor stuff/blobs/etc and build... something.
Anyone else out there tinkering yet?
Click to expand...
Click to collapse
I'd love to see a unlock/root method. Hope to see TWRP asap!
Slickademo said:
How do you unlock and root? I just got mine today
Click to expand...
Click to collapse
Unlock is just a regular Motorola unlock... lot of threads on how that is done.
Root is a little more risky and complicated to explain here. The first thing we all need is a trusted factory image -- hopefully the one above is just that. I would suspect that once we confirm a factory image, root methods will be plentiful.
mightysween said:
Got it... well, I have a completed download -- Obviously there is no way to verify the file since I have no MD5/SHA to check against. That said, the archive opens without errors, so I have boot.img now, just not enough stupidity to modify it and flash an unverified firmware back onto a brand new device.
Have a mirror uploading, will share when complete and maybe can get added to the OP.
Click to expand...
Click to collapse
I have tried downloading the file several times and always get to the very end and then it fails. I'm using idm and multiple threads and maybe I should try just a single thread..
once I get it downloaded I will validate the checksum with yours.
edit: I should add that I am in Vegas and have been able to access the link directly from the day it was posted.
Jayman007 said:
I have tried downloading the file several times and always get to the very end and then it fails. I'm using idm and multiple threads and maybe I should try just a single thread..
once I get it downloaded I will validate the checksum with yours.
edit: I should add that I am in Vegas and have been able to access the link directly from the day it was posted.
Click to expand...
Click to collapse
Oh, neat...definitely IP restricted then as I tried a VPN in LV and was still blocked. Wonder what the story is there!
Yes, if you end up with the same SHA256 let me know, we can at least be sure the file is intact.
---------- Post added at 10:37 PM ---------- Previous post was at 10:35 PM ----------
Jayman007 said:
I have tried downloading the file several times and always get to the very end and then it fails. I'm using idm and multiple threads and maybe I should try just a single thread..
once I get it downloaded I will validate the checksum with yours.
edit: I should add that I am in Vegas and have been able to access the link directly from the day it was posted.
Click to expand...
Click to collapse
Also FWIW, using that proxy link I posted gave me dl speeds of 2.5-3 Mbps, and plowed straight through to 100%.
mightysween said:
FILE: PAYTON_NPW26.83-34-0-1_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
SIZE: ~2.0 GB
CHECKSUM: UNVERIFIED! (my local SHA256: f8efa78d21f0fd4b968e860ec06b85442caaf7a93c325fbe7c5c0913306af86e)
DOWNLOAD: https://mega.nz/#!RkM2nSpL!4kHuZQfyHoSfeD-bfCcRxOi3A3rO7hz37RGcxRCglic
@Anderson_ARS , can you add this to the OP to save people asking the same question over and over and over? Thanks
Also, if you wish to try a direct download from Motorola, this link may work... it is a proxy download through NordVPN. Again, no guarantees and no way to verify (though if you end up with the same SHA256 as above, there is good chance the file is intact).
DIRECT DOWNLOAD (via anon proxy): http://proxy-it.nordvpn.com/browse....cbNvGOLw5iqOebtX0lAb+hCJw==&b=1&f=norefer&pr=
Click to expand...
Click to collapse
I downloaded it via the proxy and have the same checksum as you, so at least this means that your download is *probably* not corrupt. I don't have the device, so I'm certainly not going to flash it.
Code:
f8efa78d21f0fd4b968e860ec06b85442caaf7a93c325fbe7c5c0913306af86e PAYTON_NPW26.83-34-0-1_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
gee one said:
I downloaded it via the proxy and have the same checksum as you, so at least this means that your download is *probably* not corrupt. I don't have the device, so I'm certainly not going to flash it.
Click to expand...
Click to collapse
Thank you kindly! I downloaded again as well with same checksum, so I think we can assume the file is intact.