I am trying to flash my S III with I9300ZCUBMK2_I9300CHNBMK2_I9300ZCUBMK2_HOME.tar with Odin (tried different versions) on Windows 7. Here is the log from Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300ZCUBMK2_I9300CHNBMK2_I9300ZCUBMK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I am coming from JB 4.1.2 for the first time.
Please help me.
Thanks.
Fail at Nand
Download a new stock rom and try.
Fails its a replacement motherboard Nand damaged .
It would be worth restoring your backed up EFS folder as a try anyway .
Related
Hello all,
I rooted my galaxy s3 and all went fine, then the battery died (battery is no longer in use) so i bought a new one and all was well, upon flashing stock rom, the write failed.
When booting the phone up it says: "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
(LONG DELAY HERE)
<OSM> I9305XXBLL5_I9305EVRBLL2_I9305BVBLL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? I need help!
Bad flash wrong firmware or more likely file is corrupt .
Make sure Kies is not running as well .
jje
I really could use some help. I've been doing this for over five years and have never run into a problem like this. My dad was having some problems with his note 2 (Verizon) so he ask me to do a factory reset and either root it or put cyanogen on it. I tried using the new cyanogen installer but it said that SCH-I605 isn't supported. So I figured "whatever I'll just root it!" Well I went to root it using"NoYouVerizon-Note2" and it got halfway thru before it got stuck. I let it sit for few hours but nothing happened. So I unplug the phone and rebooted it. Then I got: "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again". Now at this point I just want to get my dad's phone working again so I tried everything I can possibly think of. I downloaded Kies (which all the forums promise will fix it). But Kies says that it doesn't support the SCH-I605 Note 2. I tried it on two different computers (one Windows and one Mac) and I even tried older versions of Kies. Now forums I've read have said that if you cant use Kies then Odin will 100% fix it. I have Odin 3.09 and the bright side is that it sees the phone and I'm able to get the phone in download mode. But everything I try to flash fails. I tried flashing a recovery and it failed. So I tried flashing two different stock roms (from stockroms.net) and both failed. They'd get to the very end of flashing and fail. I've read every forum I can find and tried everything I can think of for the past two days. But no luck. I though I'd ask and see if anyone else had any ideas because my dad needs this phone for work. I know that since Odin can see it and I can get it in download mode there has to be some way to force feed the OS down its throat but so far, no luck. Any help is greatly appreciated. Thanks in advance.
Here is what ODIN 3.09 says
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW-Rev0406_low_ship_user.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005> param.bin
<ID:0/005> recovery.img
<ID:0/005> sboot.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> sboot.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Greetings!
I downloaded the GALAXY Tab 4 7.0 firmware for Slovakia and I am trying to put it to my SM-T230NU with Odin. No SD card in device, rooted.
When I click start on Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T230XXU0ANE6_T230OXX0ANE2_T230XXU0ANE6_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> timh.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
How can I solve this problem? Thanks a lot!
I've Samsung Galaxy S3 (GT-I9300T) purchased from Australia-Telstra.
The phone is stuck at Samsung Boot Up logo and is unable to proceed further.
However i've downloaded all the firmware versions from the below mentioned location:
.sammobilecom/firmwares/d...GT-I9300T/TEL/[/url]
2014-04-01_Australia_(Telstra)_4.3_I9300TDUUGNC1_I9300TTEL GNC1_YES
2013-11-01_Australia_(Telstra)_4.1.2_I9300TDUEMJ1_I9300TTE LEMJ2 YES
2013-01-01_Australia_(Telstra)_I9300TDUELL2_I9300TTELELL2_ YES
2012-11-01_Australia_(Telstra)_I9300TDUDLK2_I9300TTELDLK2_ YES
2012-08-01_Australia_(Telstra)_I9300TDUBLH1_I9300TTELBLH1_ YES
After using the Odin3 i get the error message mentioned below (NAND WRITE START....FAIL):
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUUGNC1_I9300TTELGNC1_I9300TDUUGNA2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Desprado_14 said:
I've Samsung Galaxy S3 (GT-I9300T) purchased from Australia-Telstra.
The phone is stuck at Samsung Boot Up logo and is unable to proceed further.
However i've downloaded all the firmware versions from the below mentioned location:
.sammobilecom/firmwares/d...GT-I9300T/TEL/[/url]
2014-04-01_Australia_(Telstra)_4.3_I9300TDUUGNC1_I9300TTEL GNC1_YES
2013-11-01_Australia_(Telstra)_4.1.2_I9300TDUEMJ1_I9300TTE LEMJ2 YES
2013-01-01_Australia_(Telstra)_I9300TDUELL2_I9300TTELELL2_ YES
2012-11-01_Australia_(Telstra)_I9300TDUDLK2_I9300TTELDLK2_ YES
2012-08-01_Australia_(Telstra)_I9300TDUBLH1_I9300TTELBLH1_ YES
After using the Odin3 i get the error message mentioned below (NAND WRITE START....FAIL):
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUUGNC1_I9300TTELGNC1_I9300TDUUGNA2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Tens of threads on this subject: Search results
Hi,
So I am having trouble downgrading my Samsung Galaxy S6 (SM-G920V) from Marshmallow 6.0.2 to Lollipop 5.0.2 so that I can run a Ping Pong Root on it. The trouble is coming from Odin when I try to flash my phone. It either gets stuck showing the code below and never moves on, or progresses past this and says that it has failed. My phone is definitely not bricked as I was tricked into thinking that the downgrade worked only to see that I just reloaded my same firmware after restoring the factory data minutes earlier. I am trying to flash it with SM-G920VVRU1AOE2 which I got from SamMobile.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920VVRU1AOE2_G920VVZW1AOE2_G920VVRU1AOE2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
I either get the result shown above, or the result shown below:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have tried restarting my computer and rerunning the USB Drivers, and 3 different formats of Odin (3.11.1, 3.10.07, and 3.10.06).
Does anybody have any idea what might be going wrong and how I can fix it so that I can get my phone working again?
Thanks.