I have the Offical Samsung Flip Case (like the S-View without the window), and also a wireless charger, but the flip case has no charging receiver.
I bought this ultrathin wireless receiver from Amazon -- http://www.amazon.co.uk/Expower-Ultra-thin-Standard-Wireless-Receiver/dp/B00FWMN69I/
But now the receiver covers the contacts used by the flip case to tell the phone when case is closed so it sleeps, and to awake when the case is open.
The PCB is so thin I could easily poke a hole through with a needle, which meant I could also put a small wire through to allow outside contact so the flip-case can connect to the phone.
First I poked 2 holes just underneath the connectors of the GND and P3.
Then I placed some double-sided sticky tape over the area
And pushed some thin wire through the holes so they went through into the phone to make contact inside. I used a strand of solid CAT5 as it was what I had lieing around.
I then pushed the wire flat onto the tape and trimmed them both so they couldn't short each other
Then some aluminium foil accross the contact area. I first tried without the foil but I found it was a bit hit and miss whether the case made contact with the wire. With the foil it works every time.
Now I have a flip-case with wireless charging!
youtu.be/C_5LhUly64k
Short video of the case and charging both working togethor
I have been trying to get something like this to work with my s view cover. Thanks for the info, I'm going to give this a shot
Sent from my SM-N900T using Tapatalk
theusername said:
I have been trying to get something like this to work with my s view cover. Thanks for the info, I'm going to give this a shot
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
Uhhh wouldn't it make more sense to return your 60$ sview case and get the 80$ sview with qi charging case? I don't see why u would opt to do some junky have when u can get the official case thay offers the same functionality and isn't janky
rettignick said:
Uhhh wouldn't it make more sense to return your 60$ sview case and get the 80$ sview with qi charging case? I don't see why u would opt to do some junky have when u can get the official case thay offers the same functionality and isn't janky
Click to expand...
Click to collapse
Frist off, the official charging case is very thick compaired to the regular one. Second the wireless charging cases are hard to come by. Third this is XDA, is all about customization, hacking, and development. If you don't like it, don't go to that thread. Last of all, just by your use of the word "janky" I can tell you are an idiot. Please go flame some where else.
Sent from my SM-N900T using Tapatalk
Stalka said:
I have the Offical Samsung Flip Case (like the S-View without the window), and also a wireless charger, but the flip case has no charging receiver.
I bought this ultrathin wireless receiver from Amazon -- http://www.amazon.co.uk/Expower-Ultra-thin-Standard-Wireless-Receiver/dp/B00FWMN69I/
But now the receiver covers the contacts used by the flip case to tell the phone when case is closed so it sleeps, and to awake when the case is open.
The PCB is so thin I could easily poke a hole through with a needle, which meant I could also put a small wire through to allow outside contact so the flip-case can connect to the phone.
First I poked 2 holes just underneath the connectors of the GND and P3.
Then I placed some double-sided sticky tape over the area
And pushed some thin wire through the holes so they went through into the phone to make contact inside. I used a strand of solid CAT5 as it was what I had lieing around.
I then pushed the wire flat onto the tape and trimmed them both so they couldn't short each other
Then some aluminium foil accross the contact area. I first tried without the foil but I found it was a bit hit and miss whether the case made contact with the wire. With the foil it works every time.
Now I have a flip-case with wireless charging!
youtu.be/C_5LhUly64k
Short video of the case and charging both working togethor
Click to expand...
Click to collapse
Doesn't this add a irregular hump on the back at the wireless ports? The Original samsung S-view case has two wireless pillars sticking out to fit in the wireless ports. You covered the ports with two wires, how is it not adding a little hump on the back?
Deekayy said:
Doesn't this add a irregular hump on the back at the wireless ports? The Original samsung S-view case has two wireless pillars sticking out to fit in the wireless ports. You covered the ports with two wires, how is it not adding a little hump on the back?
Click to expand...
Click to collapse
Not that I can notice. It does make it more difficult to close the case but once closed I don't see any hump and still feels flat when laid on a surface.
Also the flip cases "pillars" are very thin compared to the ones on the official wireless charging cover.
You could always hammer the wire flat prior to inserting if you wanted.
Stalka said:
Not that I can notice. It does make it more difficult to close the case but once closed I don't see any hump and still feels flat when laid on a surface.
Also the flip cases "pillars" are very thin compared to the ones on the official wireless charging cover.
You could always hammer the wire flat prior to inserting if you wanted.
Click to expand...
Click to collapse
Nice hack especially for those of us in the UK who have just managed to get a free standard Flip Case from Samsung.
Vince
I feel really stupid not being able to track down a definitive answer but, I have the Verizon Note 3 and the OEM "Samsung Galaxy Note 3 S-View Flip Cover"... does this thing have wireless charging built-in? I see that there are contacts on the cover inside the back and the Note 3 itself has the contacts exposed, so it doesn't look at all like the pictures in OP.
xeper said:
I feel really stupid not being able to track down a definitive answer but, I have the Verizon Note 3 and the OEM "Samsung Galaxy Note 3 S-View Flip Cover"... does this thing have wireless charging built-in? I see that there are contacts on the cover inside the back and the Note 3 itself has the contacts exposed, so it doesn't look at all like the pictures in OP.
Click to expand...
Click to collapse
Samsung offers 2 different S-View covers. One has Qi charging built-in, while the other one does not. The Qi S-View cover is not easy to find at the present time, while the standard S-View cover is readily available. Where did you purchase your S-View cover? The package will tell you which cover it is.
If you didn't personally purchase the cover or don't have the packaging that it came in, then post a pic showing the pins/contacts on the inside of the S-View cover you have. We should be able to tell you which one you have, and if it has Qi capabilities or not.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
That's awesome bro. I will acquire a wireless charger and attempt your findings...
Sent from my SM-N9005 using XDA Premium 4 mobile app
Stalka said:
I have the Offical Samsung Flip Case (like the S-View without the window), and also a wireless charger, but the flip case has no charging receiver.
I bought this ultrathin wireless receiver from Amazon -- http://www.amazon.co.uk/Expower-Ultra-thin-Standard-Wireless-Receiver/dp/B00FWMN69I/
But now the receiver covers the contacts used by the flip case to tell the phone when case is closed so it sleeps, and to awake when the case is open.
The PCB is so thin I could easily poke a hole through with a needle, which meant I could also put a small wire through to allow outside contact so the flip-case can connect to the phone.
First I poked 2 holes just underneath the connectors of the GND and P3.
Then I placed some double-sided sticky tape over the area
And pushed some thin wire through the holes so they went through into the phone to make contact inside. I used a strand of solid CAT5 as it was what I had lieing around.
I then pushed the wire flat onto the tape and trimmed them both so they couldn't short each other
Then some aluminium foil accross the contact area. I first tried without the foil but I found it was a bit hit and miss whether the case made contact with the wire. With the foil it works every time.
Now I have a flip-case with wireless charging!
youtu.be/C_5LhUly64k
Short video of the case and charging both working togethor
Click to expand...
Click to collapse
Thank you. I've definitely been looking for this info. I'm just a bit confused as to what you are contacting on the underside. You can't see that part. There are 3 little holes on the left side of the battery. Does your wire contact just the bottom one? Or does it act as a jumper and contact the middle one and the bottom one? I'm using a slightly different charging receiver. Thanks!
stanglifemike said:
Samsung offers 2 different S-View covers. One has Qi charging built-in, while the other one does not. The Qi S-View cover is not easy to find at the present time, while the standard S-View cover is readily available. Where did you purchase your S-View cover? The package will tell you which cover it is.
If you didn't personally purchase the cover or don't have the packaging that it came in, then post a pic showing the pins/contacts on the inside of the S-View cover you have. We should be able to tell you which one you have, and if it has Qi capabilities or not.
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
Click to expand...
Click to collapse
I don't see the Qi info on the cover or package, so I'm assuming not. Attaching a pic just in case.
If it's not a wireless charging back, what are the contacts for? NFC? (and if it's NFC, why doesn't the standard back need the same?)
xeper said:
I don't see the Qi info on the cover or package, so I'm assuming not. Attaching a pic just in case.;
If it's not a wireless charging back, what are the contacts for? NFC? (and if it's NFC, why doesn't the standard back need the same?)
Click to expand...
Click to collapse
/
Those contacts are part of a chip that tells the Phone what Kind of Cover is attached.
If you had a charging Cover there would be 3 contacts there plus 2 horizontal contacts higher and to the left for the NFC.
Sent from my SM-N900T using xda app-developers app
xeper said:
I don't see the Qi info on the cover or package, so I'm assuming not. Attaching a pic just in case.
If it's not a wireless charging back, what are the contacts for? NFC? (and if it's NFC, why doesn't the standard back need the same?)
Click to expand...
Click to collapse
That's the non-wireless charging S-View case. I have the same thing (in white) and was able to mod it to make the S-View AND wireless charging to work.
To the OP, thank you for the aluminum foil idea!! That's the one part my hack was missing as everytime I removed the case it was hit or miss with the contacts lining up correctly.
htcoveblue said:
Thank you. I've definitely been looking for this info. I'm just a bit confused as to what you are contacting on the underside. You can't see that part. There are 3 little holes on the left side of the battery. Does your wire contact just the bottom one? Or does it act as a jumper and contact the middle one and the bottom one? I'm using a slightly different charging receiver. Thanks!
Click to expand...
Click to collapse
The three contacts to the left of battery are:
1. [CHARGE]
2. [GROUND]
3. [DATA]
The [DATA] part is used by the phone to determine what type of case is attached. The wireless charger connects to 1 and 2, whilst the flip-case connects to 2 and 3. So the holes are in the bottom two and allow the flip case to be recognized by the phone.
The best way to do this is to just buy the Techmatte Qi receiver! It leaves the contacts open on both sides, so my official Samsung S-View case works perfectly without ANY modifications needed!! Highly recommend that everyone go that route!
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
nice job!
stanglifemike said:
The best way to do this is to just buy the Techmatte Qi receiver!
Click to expand...
Click to collapse
Yes this would be the perfect solution.
I searched Google Shopping, eBay and Amazon for "Techmatte" and got no results
Anyone know of a UK seller or somewhere that ships to the UK with this in stock?
stanglifemike said:
The best way to do this is to just buy the Techmatte Qi receiver! It leaves the contacts open on both sides, so my official Samsung S-View case works perfectly without ANY modifications needed!! Highly recommend that everyone go that route!
SwiftKey'ed from my White Sprint Note 3 via XDA Premium
Click to expand...
Click to collapse
Yes this is the best solution, but apparently, there will be many people who will buy the 1 to 1 copy s view cover, and not all of these will work.
Stalka said:
Yes this would be the perfect solution.
I searched Google Shopping, eBay and Amazon for "Techmatte" and got no results
Anyone know of a UK seller or somewhere that ships to the UK with this in stock?
Click to expand...
Click to collapse
This LOOKS like it will work the same:
http://www.amazon.co.uk/Mudder-Ultr...8&qid=1386782251&sr=8-15&keywords=qi+receiver
Sent from my Nexus 10 using xda app-developers app
Related
I passed on a Steelie because of the thickness of the magnet that I'd have to attach to my phone or case. I just ordered an iMagnet, a Tetrax XWay, and a $7 Cellet (pretty much because it was $7). When they arrive in 2 days, I'll post a follow-up. I've never owned a magnetic mount, and I'm facinated by the concept.
I am not so much opposed to the Steelie, but somehow, ordering 3 mounts felt justifiable and 4 mounts felt super crazy.
I'm curious what experiences others have had with magnetic car mounts.
mychal said:
I passed on a Steelie because of the thickness of the magnet that I'd have to attach to my phone or case. I just ordered an iMagnet, a Tetrax XWay, and a $7 Cellet (pretty much because it was $7). When they arrive in 2 days, I'll post a follow-up. I've never owned a magnetic mount, and I'm facinated by the concept.
I am not so much opposed to the Steelie, but somehow, ordering 3 mounts felt justifiable and 4 mounts felt super crazy.
I'm curious what experiences others have had with magnetic car mounts.
Click to expand...
Click to collapse
I have the Tetrax Fixway for my current gnex and it's great. It's the main reason I changed my mind about getting the s-view cover. I wouldn't be able to use the tetrax with it. Just for fun, I mounted up my and Galaxy Note 8.0 using a TPU case on my tetrax and used it as navigation for a few days. It worked fine, so I'm not too worried about the GN3.
mastervm said:
I have the Tetrax Fixway for my current gnex and it's great. It's the main reason I changed my mind about getting the s-view cover. I wouldn't be able to use the tetrax with it. Just for fun, I mounted up my and Galaxy Note 8.0 using a TPU case on my tetrax and used it as navigation for a few days. It worked fine, so I'm not too worried about the GN3.
Click to expand...
Click to collapse
Dont these magnetic mounts interfere with S-pen, NFC and wireless charging?
deathshead said:
Dont these magnetic mounts interfere with S-pen, NFC and wireless charging?
Click to expand...
Click to collapse
Of the 4, only the Steelie has an actual magnet on the phone, I think. The others just require metal plates or buttons on/in the phone or case. So they should be fine when not in the dock. I won't use the S-pen while docked, so I'm good there. And I don't use NFC or wireless charging yet.
But, yes, the Steelie will cause a circular spot on the screen where the pen won't write. Hopefully, I'm right about the metal plates for the others, but I'll let you know...
So what does anybody use NFC for anyway? And what kind of wireless charging are folks already using with their N3? I'm curious.
mychal said:
Hopefully, I'm right about the metal plates for the others, but I'll let you know...
Click to expand...
Click to collapse
The arrangement of the 4 magnets in the dock itself make it so the field is circled around the button. Tetrax has a demo video on their website under Support > FAQ. I can't link urls yet.
I use NFC to make purchases occasionally and haven't had any issues. You did just remind me about wireless charging which I plan to do for this phone. Hopefully the button doesn't lift the gn3 too far away from the pad.
Hey guys just an update on this product. I bought an iMagnet http://www.amazon.com/Cradle-less-Q...e=UTF8&qid=1380960297&sr=8-1&keywords=imagnet
This came with 2 square adhesive metal plates and 1 round non-adhesive metal plate. I tried several configurations and here are the results (with nfc):
1. Metal plate between battery and back cover (square): NFC interferes completely
2. Metal plate between battery and back cover (round): NFC sometimes work
3. Metal plate BENEATH battery square AND round: NFC works perfectly
The third configuration is what I'm using and does not interfere with NFC and S-beam. Oh, and no bulging on standard battery cover door.
JBNAquatics said:
Hey guys just an update on this product. I bought an iMagnet http://www.amazon.com/Cradle-less-Q...e=UTF8&qid=1380960297&sr=8-1&keywords=imagnet
3. Metal plate BENEATH battery square AND round: NFC works perfectly
The third configuration is what I'm using and does not interfere with NFC and S-beam. Oh, and no bulging on standard battery cover door.
Click to expand...
Click to collapse
Are you talking about putting the metal plates inside the OEM back cover of a Note 3? Please post a picture of the plate inside the phone, I can't visualize how/where there's room with that huge battery taking up so much space, it extends down almost to the base of the phone.
Sent from my Nexus 10 using xda app-developers app
I think he's saying that he took the battery out and put it underneath
gnik luap said:
Are you talking about putting the metal plates inside the OEM back cover of a Note 3? Please post a picture of the plate inside the phone, I can't visualize how/where there's room with that huge battery taking up so much space, it extends down almost to the base of the phone.
Sent from my Nexus 10 using xda app-developers app
Click to expand...
Click to collapse
Yes please can you post a picture. I was planning on getting the steelie, but it is good I read the reviews before that it interferes with the phone. And I was worried about the adhesive material sticking to the back cover. I am wanting to get this mount as well. So if pictures can be shown that would be greatly appreciated. That way I can buy it right away :good:
JBNAquatics said:
Hey guys just an update on this product. I bought an iMagnet http://www.amazon.com/Cradle-less-Q...e=UTF8&qid=1380960297&sr=8-1&keywords=imagnet
This came with 2 square adhesive metal plates and 1 round non-adhesive metal plate. I tried several configurations and here are the results (with nfc):
1. Metal plate between battery and back cover (square): NFC interferes completely
2. Metal plate between battery and back cover (round): NFC sometimes work
3. Metal plate BENEATH battery square AND round: NFC works perfectly
The third configuration is what I'm using and does not interfere with NFC and S-beam. Oh, and no bulging on standard battery cover door.
Click to expand...
Click to collapse
Would it work if I had a TPU case on like the Diztronic?
Sent from my SM-N900T using xda app-developers app
JBNAquatics said:
Hey guys just an update on this product. I bought an iMagnet
This came with 2 square adhesive metal plates and 1 round non-adhesive metal plate. I tried several configurations and here are the results (with nfc):
1. Metal plate between battery and back cover (square): NFC interferes completely
2. Metal plate between battery and back cover (round): NFC sometimes work
3. Metal plate BENEATH battery square AND round: NFC works perfectly
The third configuration is what I'm using and does not interfere with NFC and S-beam. Oh, and no bulging on standard battery cover door.
Click to expand...
Click to collapse
Also curious about this...would you mind helping us out with some pictures pls?
Also, for JBN, Mychal (OP) and anyone else who has this - what do you do for charging? Just use the cable straight from the plug? Or have you found a nice way to wrap it on the mount, etc? If this iMagnet had wireless charging that would be incredible...
The Imagnet works great!
I have the imagnet and am currently using it on my note 3. I have the metal rectangular piece with adhesive in the phone on top of the battery but beneath the battery door. It works fine inside there and does not effect the screen or s-pen even while connected to the mount. The metal strip is actually not a magnet, it's some sort of metal material but it is not magnetic. I used the rectangular metal piece on my note 2 above the the battery door and beneath my tpu case i had and it added no noticeable bulk. My tpu case fit on there just fine. I used it for 4months will no problem,. Occasionally because of the houston texas heat I would find the imagnet on the floor in my car sometimes. I would just rinse the bottom off with soap and water ( because the bottom of it has a sticky gel ) and would stick it right back on like brand new. The bottom also uses suction, so it combines both. With ac running in the car the mount will not come off unless the bottom is dirty from not cleaning before you stick it on there. While the phone is mounted and in the 4 months I have used it my phone has never came off the mount. As fas as nfc is concerned I don't use it, so i have no idea if it works or not. The imagnet has been a real blessing in my life and others love it as-well. I'm going to start getting it as gifts for people for Christmas.
This is a users video review from youtube. Check it out and hope this helps!
http://www.youtube.com/watch?v=breb2l3RoXI
I use the steelie, and the magnet interfering with the S Pen is a problem for me. What I plan on doing is sticking the magnet to the back of the belt clip holster that comes with the seidio surface case. I ordered a separate holster to also use with the GameKlip.
I just got the iMagnet today. I put both rectangular plates between my Diztronic TPU case and the back of the phone. Works great. NFC also worked for me with no problems. Was able to beam some pics to an S3 with NFC.
Sent from my SM-N900T using xda app-developers app
JBNAquatics said:
Hey guys just an update on this product. I bought an iMagnet http://www.amazon.com/Cradle-less-Q...e=UTF8&qid=1380960297&sr=8-1&keywords=imagnet
This came with 2 square adhesive metal plates and 1 round non-adhesive metal plate. I tried several configurations and here are the results (with nfc):
1. Metal plate between battery and back cover (square): NFC interferes completely
2. Metal plate between battery and back cover (round): NFC sometimes work
3. Metal plate BENEATH battery square AND round: NFC works perfectly
The third configuration is what I'm using and does not interfere with NFC and S-beam. Oh, and no bulging on standard battery cover door.
Click to expand...
Click to collapse
Only problem with the third configuration is that it doesn't stick to the mount.
takhawaja said:
Yes please can you post a picture. I was planning on getting the steelie, but it is good I read the reviews before that it interferes with the phone. And I was worried about the adhesive material sticking to the back cover. I am wanting to get this mount as well. So if pictures can be shown that would be greatly appreciated. That way I can buy it right away :good:
Click to expand...
Click to collapse
Yes, that's what he means. I'm sorry I don't have another camera except the phone, but I wanted to chime in and ensure this method. Pop the oem back off, lay the plate on top of the battery, and pop the back on. No adhesive necessary to hold it in place. No bulge, as the plate is quite thin.
I use the bear bumper case, so the magnet is very strong. I've tested with a tpu case and it still works, just not as satisfyingly strong. Anything bigger than that and just stick a second plate between the case and the phone.
Never had imagnet before this, and I love it. Very clean solution, and the ultimate in one handed operation.
Cheers!
Nick
Sent from my enormous Note 3 via Tapatalk.
Tetrax Fixway
Hi!
Does anybody know how big (cm) the fixway is?
I just wanna know for sure that it will fit in my car so..
Grtz
natalie_g said:
Hi!
Does anybody know how big (cm) the fixway is?
I just wanna know for sure that it will fit in my car so..
Grtz
Click to expand...
Click to collapse
Hi,
about 5cm end2end. Just wondering how are you going to stick metal plate to the back of note-3?
I used Tetrax with my SGS1 and I really love it. I've ordered glossy back cover for my note-3 as I see it the only option...
i have the imagnet and a seidio surface case for my Note 3....I put the metal plate under the case, and while the magnet is strong, I find the phone spinning around when im driving...anyone else have that issue?
Hey guys,
I am new to wireless charging and one of my colleague talks highly positive of the concept. Specially when at night, how easy it is to pick up the phone from the charging pad, surf for a while and put it back without the hassle of looking for the wire and plugging into the ports.
I have a note 3.. and planning to go for a sgp neo hybrid case.. will i be able to make use of the charging pad along with the neo hybrid case. I do understand that a custom case cover is needed for using the wireless charging kit.. which is provided by samsung for S4. but i think they still havent come up for N3.
Anyhow i've seen on various youtube videos that many a times third party cases also work with wirelss charging without the mod/hack. Anyone tried neo hybrid for n3 with their charging pads?
I have tested this with 3 different cases except the Spigen because I haven't received it yet but I don't think that this case will be the exception
Sent from my SM-N9005 using Tapatalk
BlueChris said:
I have tested this with 3 different cases except the Spigen because I haven't received it yet but I don't think that this case will be the exception
Sent from my SM-N9005 using Tapatalk
Click to expand...
Click to collapse
Thanks for your reply, but what was the outcome? were u able to charge with the third party cases? Are the charging times same.. slower or faster.
With Samsung charging kit that includes the back cover and the pad, they claim that the charging is faster than conventional charging cos it charges at 600MAh's.
M8 QI has sensor at least my pad has so if it beeps and light goes green in pad no matter if I have the phone naked or in a case it charges with 640ma this charge my phone in 4 to 5 hours which occurs every night and I am fine. Imagine that I had put a plastic cap in bottom of phone to have the usb3 plug clean from dust.
Sent from my SM-N9005 using Tapatalk
Wireless Chargeing
MANswers said:
Hey guys,
I am new to wireless charging and one of my colleague talks highly positive of the concept. Specially when at night, how easy it is to pick up the phone from the charging pad, surf for a while and put it back without the hassle of looking for the wire and plugging into the ports.
I have a note 3.. and planning to go for a sgp neo hybrid case.. will i be able to make use of the charging pad along with the neo hybrid case. I do understand that a custom case cover is needed for using the wireless charging kit.. which is provided by samsung for S4. but i think they still havent come up for N3.
Anyhow i've seen on various youtube videos that many a times third party cases also work with wirelss charging without the mod/hack. Anyone tried neo hybrid for n3 with their charging pads?
Click to expand...
Click to collapse
T-Mobile has a wireless charging stand for sale for the N3. Its 69.99 and apply fallfun co to get 30% off. It doesnt say a back cover is needed. All thaats included is the stand cable and AC plug. I just ordered one so I will post results.
BlueChris said:
M8 QI has sensor at least my pad has so if it beeps and light goes green in pad no matter if I have the phone naked or in a case it charges with 640ma this charge my phone in 4 to 5 hours which occurs every night and I am fine. Imagine that I had put a plastic cap in bottom of phone to have the usb3 plug clean from dust.
Sent from my SM-N9005 using Tapatalk
Click to expand...
Click to collapse
Plugging off the port is a good idea.. thanks for your response.. i will start reviewing good wireless chargers now including the one you mentioned and the one jerry mentions below.
jerryjans11 said:
T-Mobile has a wireless charging stand for sale for the N3. Its 69.99 and apply fallfun co to get 30% off. It doesnt say a back cover is needed. All thaats included is the stand cable and AC plug. I just ordered one so I will post results.
Click to expand...
Click to collapse
Jerry thanks for your response and your the discount code. i will start reading the pros and cons of the charger.
Can you try to upload some pictures etc.. i like the 45 degree slant.. its like a dock.. that charges wirelessly.. instead of placing on a pad. Good stuff.
Pls try to put some reviews. If you can today i will place the order tonight.
The 45 degree needs inside the back cover I think 4 metal things and the base has magnets and that's how it stands. I have this http://pages.ebay.com/link/?nav=item.view&id=360732881624&globalID=EBAY-AU and is working fine, I had post a video also in the 1st wireless thread here https://www.youtube.com/watch?v=9LaQQnc2dmU&feature=youtube_gdata_player that I demonstrate it
Sent from my SM-N9005 using Tapatalk
jerryjans11 said:
T-Mobile has a wireless charging stand for sale for the N3. Its 69.99 and apply fallfun co to get 30% off. It doesnt say a back cover is needed. All thaats included is the stand cable and AC plug. I just ordered one so I will post results.
Click to expand...
Click to collapse
That's just your standard Qi charging pad. Won't work with your N3 unless you have the 'official' Samsung charging back plate, or you modify a receiver between your stock back plate, and battery.
In my experience,
With the samsung charging back plate, none of the standard N3 cases will fit on the phone anymore. It's because the back plate is thicker than the stock one.
With a receiver installed between the stock back plate and battery, it will bulge out. I don't like that either.
jerryjans11 said:
T-Mobile has a wireless charging stand for sale for the N3. Its 69.99 and apply fallfun co to get 30% off. It doesnt say a back cover is needed. All thaats included is the stand cable and AC plug. I just ordered one so I will post results.
Click to expand...
Click to collapse
Another thing, the charger is a 1Amp charger, i believe for the N3 you need atleast 2Amp.
skyline23 said:
That's just your standard Qi charging pad. Won't work with your N3 unless you have the 'official' Samsung charging back plate, or you modify a receiver between your stock back plate, and battery.
In my experience,
With the samsung charging back plate, none of the standard N3 cases will fit on the phone anymore. It's because the back plate is thicker than the stock one.
With a receiver installed between the stock back plate and battery, it will bulge out. I don't like that either.
Click to expand...
Click to collapse
I am not sure if the N3 and S4 use the same charging technology, cos in this video below the guy is charging a S4 on the TYLT
http://www.youtube.com/watch?v=K5g2rVraB1g
The thing i like about tylt is that it has three coils for charging unlike one for others, where u dont have to find the sweet spot... and lay your phone to pickup the right spot for charging.. demo on this video
http://www.youtube.com/watch?v=hF3yFvMXKZw
MANswers said:
I am not sure if the N3 and S4 use the same charging technology, cos in this video below the guy is charging a S4 on the TYLT
http://www.youtube.com/watch?v=K5g2rVraB1g
The thing i like about tylt is that it has three coils for charging unlike one for others, where u dont have to find the sweet spot... and lay your phone to pickup the right spot for charging.. demo on this video
http://www.youtube.com/watch?v=hF3yFvMXKZw
Click to expand...
Click to collapse
What I was trying to clarify, that even if you bought that charging stand, you'll need the wireless receiver on the phone itself.
That didn't seem clear to everyone on this thread.
skyline23 said:
What I was trying to clarify, that even if you bought that charging stand, you'll need the wireless receiver on the phone itself.
That didn't seem clear to everyone on this thread.
Click to expand...
Click to collapse
I still didnt get that mate.
T-Mobile's site mentions that this charger is compatible with Note 3
http://www.t-mobile.com/accessories/tylt-wireless-charger-black.html#features
And it doesnt mention about any charging receiver based cover
Code:
Compatible Devices
Galaxy Note 3 - Black
Galaxy S® 4 - Black Mist - 16GB
Lumia 810
Lumia 925
Nexus 4 - No Annual Contract
Galaxy Note 3 - White
Galaxy S® 4 - White Frost - 16GB
Lumia 810 - Refurbished
Nexus 4
Nexus 4 - White
MANswers said:
I still didnt get that mate.
T-Mobile's site mentions that this charger is compatible with Note 3
http://www.t-mobile.com/accessories/tylt-wireless-charger-black.html#features
And it doesnt mention about any charging receiver based cover
Code:
Compatible Devices
Galaxy Note 3 - Black
Galaxy S® 4 - Black Mist - 16GB
Lumia 810
Lumia 925
Nexus 4 - No Annual Contract
Galaxy Note 3 - White
Galaxy S® 4 - White Frost - 16GB
Lumia 810 - Refurbished
Nexus 4
Nexus 4 - White
Click to expand...
Click to collapse
That's only if you have the official Samsung charging back installed.
See this link;
http://www.mobilefun.com/40793-official-samsung-galaxy-note-3-wireless-charging-cover---black.htm
The Note 3 does not support wireless charging unless you buy that back, or a receiver that goes between the battery and stock back plate.
http://www.amazon.com/Standard-Wire...40793&sr=8-4&keywords=note+3+wireless+charger
skyline23 said:
That's only if you have the official Samsung charging back installed.
See this link;
http://www.mobilefun.com/40793-official-samsung-galaxy-note-3-wireless-charging-cover---black.htm
The Note 3 does not support wireless charging unless you buy that back, or a receiver that goes between the battery and stock back plate.
http://www.amazon.com/Standard-Wire...40793&sr=8-4&keywords=note+3+wireless+charger
Click to expand...
Click to collapse
Thanks for all the links.
I guess i understand about the receiver now. Just read the whole wireless charging thread on this section.
This is totally new to me, hence the confusion... the back cover you mentioned.. does it add bulk to the phone.. as in thickness?
Is there a way a single coil or some chip can be added to the current phone cover. I have verizon model.
MANswers said:
Thanks for all the links.
I guess i understand about the receiver now. Just read the whole wireless charging thread on this section.
This is totally new to me, hence the confusion... the back cover you mentioned.. does it add bulk to the phone.. as in thickness?
Is there a way a single coil or some chip can be added to the current phone cover. I have verizon model.
Click to expand...
Click to collapse
Yes, the samsung wireless charging cover is thicker. Will add 2mm, therefore, all your cases won't fit. Including the Neo Hybrid.
You can get receiver that goes between the battery and cover, but from my experience, it makes the rear cover bulge a bit.
MANswers said:
Hey guys,
I am new to wireless charging and one of my colleague talks highly positive of the concept. Specially when at night, how easy it is to pick up the phone from the charging pad, surf for a while and put it back without the hassle of looking for the wire and plugging into the ports.
I have a note 3.. and planning to go for a sgp neo hybrid case.. will i be able to make use of the charging pad along with the neo hybrid case. I do understand that a custom case cover is needed for using the wireless charging kit.. which is provided by samsung for S4. but i think they still havent come up for N3.
Anyhow i've seen on various youtube videos that many a times third party cases also work with wirelss charging without the mod/hack. Anyone tried neo hybrid for n3 with their charging pads?
Click to expand...
Click to collapse
1) Samsung has a wireless charging back (wireless receiver built-in) that replaces the battery cover/back already on the phone.
It makes the phone too thick for a case (a bumper might work).
2) They also make a S-view flip cover that replaces the stock back and has the wireless receiver built-in, no additional case needed.
3) Aftermarket Qi receivers can be purchased on Amazon and eBay that are placed inside the stock back cover, and if they don't cause a significant bulge in the back you can use a normal case, but one with a TPU or silicone back is most likely to work.
4) If you have a Qi receiver from a Note 2 (or similar) you can modify it to work inside the stock back cover.
ALL of those methods will require a Qi transmitter, or charging pad.
At least one seller on Amazon is offering a kit with both the Qi insert & charging pad, about $30 when I last looked.
Sent from my Nexus 10 using xda app-developers app
skyline23 said:
Yes, the samsung wireless charging cover is thicker. Will add 2mm, therefore, all your cases won't fit. Including the Neo Hybrid.
You can get receiver that goes between the battery and cover, but from my experience, it makes the rear cover bulge a bit.
Click to expand...
Click to collapse
One the posts mentioned in the wireless charging thread..
http://detail.tmall.com/item.htm?sp...289ff7c5f8bb4fe28bbdb230a58&scene=taobao_shop
and
http://dx-box.com/qi-wireless-charg...msung-galaxy-note-iii-3-n900-n9005-n9000.html
Looks like these recievers can be easily inserted into the back cover.. anyone tried it yet? or whats your opinion about this?
Adding the official samsung back cover with 2mm is not a big issue, but i dont wan to loose the phone protection without a neo hybrid.
gnik luap said:
1) Samsung has a wireless charging back (wireless receiver built-in) that replaces the battery cover/back already on the phone.
It makes the phone too thick for a case (a bumper might work).
2) They also make a S-view flip cover that replaces the stock back and has the wireless receiver built-in, no additional case needed.
3) Aftermarket Qi receivers can be purchased on Amazon and eBay that are placed inside the stock back cover, and if they don't cause a significant bulge in the back you can use a normal case, but one with a TPU or silicone back is most likely to work.
4) If you have a Qi receiver from a Note 2 (or similar) you can modify it to work inside the stock back cover.
ALL of those methods will require a Qi transmitter, or charging pad.
At least one seller on Amazon is offering a kit with both the Qi insert & charging pad, about $30 when I last looked.
Sent from my Nexus 10 using xda app-developers app
Click to expand...
Click to collapse
Thanks that is great information. Can you post the amazon link?
BlueChris said:
The 45 degree needs inside the back cover I think 4 metal things and the base has magnets and that's how it stands. I have this http://pages.ebay.com/link/?nav=item.view&id=360732881624&globalID=EBAY-AU and is working fine, I had post a video also in the 1st wireless thread here https://www.youtube.com/watch?v=9LaQQnc2dmU&feature=youtube_gdata_player that I demonstrate it
Sent from my SM-N9005 using Tapatalk
Click to expand...
Click to collapse
I was looking at the video again, it doesnt look like attaching the receiver on your original cover has added any bulk or thickness right? Do you think it will fit the neo hybrid case.
Amazon has these receivers for 10 bucks or so.. i was planning to get one of these receivers and then get the TYLT pad for charging.. I was reading reviews accross various forums, and people are having high opinions about TYLT's features.
MANswers said:
One the posts mentioned in the wireless charging thread..
http://detail.tmall.com/item.htm?sp...289ff7c5f8bb4fe28bbdb230a58&scene=taobao_shop
and
http://dx-box.com/qi-wireless-charg...msung-galaxy-note-iii-3-n900-n9005-n9000.html
Looks like these recievers can be easily inserted into the back cover.. anyone tried it yet? or whats your opinion about this?
Adding the official samsung back cover with 2mm is not a big issue, but i dont wan to loose the phone protection without a neo hybrid.
Thanks that is great information. Can you post the amazon link?
Click to expand...
Click to collapse
The cheap one may have been from eBay, or it's gone up.
Best price I see for a kit now is $48, http://www.amazon.com/Standard-Wire..._1_3?s=wireless&ie=UTF8&qid=1382047175&sr=1-3
There is a $10 qi insert:
http://www.amazon.com/Docooler-Stan...1382048041&sr=1-19&keywords=note+3+qi+charger
plus a $20 charging pad:
http://www.amazon.com/DigiYes®-Stan...1382048041&sr=1-23&keywords=note+3+qi+charger
By the way, I ordered an insert from that seller, it said "in stock" but the expected delivery time was 24 to 43 days once I got the order in. It does seem like you should know that before ordering.
Sent from my Nexus 10 using xda app-developers app
gnik luap said:
The cheap one may have been from eBay, or it's gone up.
Best price I see for a kit now is $48, http://www.amazon.com/Standard-Wire..._1_3?s=wireless&ie=UTF8&qid=1382047175&sr=1-3
There is a $10 qi insert:
http://www.amazon.com/Docooler-Stan...1382048041&sr=1-19&keywords=note+3+qi+charger
plus a $20 charging pad:
http://www.amazon.com/DigiYes®-Stan...1382048041&sr=1-23&keywords=note+3+qi+charger
By the way, I ordered an insert from that seller, it said "in stock" but the expected delivery time was 24 to 43 days once I got the order in. It does seem like you should know that before ordering.
Sent from my Nexus 10 using xda app-developers app
Click to expand...
Click to collapse
Thanks for that info, i was about to place an order with that seller.. why wait for over a month when you can get the same from a US seller for the same price.
I was wondering if the receiver for Note 2 will work on the Note 3.
Many a US sellers are selling the recievers for Note 2.
http://www.ebay.com/itm/Qi-Wireless...l_Phone_PDA_Chargers&var=&hash=item565c879fa2
Hi on my note 3 I decided to be clever and purchase a wireless rear battery cover ... you know not the stick on QI charging sticker that goes onto the battery but the expensive complete replacement cover that replaces the battery cover and adds wireless charging toi the note 3
Well ... just for the record it is THICKER than a normal battery cover so you cant fit the note into a case OTTERBOX Defender in my example
just thought this should be on record ... so the advice is to save money and get the cheapers internal stick on QI receiver and not the replacement rear cover
hopes this is of use and save somebody cash and problems when fitting the note 3 into a protective case if its got the charging battery cover
The best way to save cash is just buy one wireless card. more cheap and no additional thicker.
fibreoptix said:
Hi on my note 3 I decided to be clever and purchase a wireless rear battery cover ... you know not the stick on QI charging sticker that goes onto the battery but the expensive complete replacement cover that replaces the battery cover and adds wireless charging toi the note 3
Well ... just for the record it is THICKER than a normal battery cover so you cant fit the note into a case OTTERBOX Defender in my example
just thought this should be on record ... so the advice is to save money and get the cheapers internal stick on QI receiver and not the replacement rear cover
hopes this is of use and save somebody cash and problems when fitting the note 3 into a protective case if its got the charging battery cover
Click to expand...
Click to collapse
This one is cheap and it works.... and you use the original back cover, so you can use a normal case. Please be advised that is creates just a little bump just below the camera.
xdm9mm said:
This one is cheap and it works.... and you use the original back cover, so you can use a normal case. Please be advised that is creates just a little bump just below the camera.
Click to expand...
Click to collapse
Have you read anywhere that indicates a slim case still works? I have the Incipio case on it and don't want to lose its use but want the wireless charging. Thanks.
rndchef said:
Have you read anywhere that indicates a slim case still works? I have the Incipio case on it and don't want to lose its use but want the wireless charging. Thanks.
Click to expand...
Click to collapse
It should fit because the bump is not that big [though you better do some research first] . I used a UAG navigator on mine and that case was a tight fitting case and it still fit.
xdm9mm said:
This one is cheap and it works.... and you use the original back cover, so you can use a normal case. Please be advised that is creates just a little bump just below the camera.
Click to expand...
Click to collapse
i wonder if this works works the otterbox case
Greatness83 said:
i wonder if this works works the otterbox case
Click to expand...
Click to collapse
try folding a piece of paper to .5mm thickness, maybe half inch square and put it inside your phone on the upper part of the Note 3's battery, put back cover on, then try the otterbox case.....
look in post no. 1996 of this thread so you have an idea how the receiver looks like.
goodluck
Mod Edit
Thread Closed
Please see Wireless charging on the Note3? thread already started on this.
thank you
ronnie498
Forum moderator
Black one in stock now: http://www.mobilefun.com/47945-official-samsung-galaxy-alpha-qi-wireless-charging-cover-black.htm
White one on preorder: http://www.mobilefun.com/47948-official-samsung-galaxy-alpha-qi-wireless-charging-cover-white.htm
For wireless charging how does this exactly work?
It works by induction. You need a special charging station (read: a square box that is resting on your nightstand from now on), where you can put your phone on. You don't have to fiddle with plugs.
The charging station works with a standard USB connection and for your phone you need the above mentioned back cover, with is a complete replacement for the existing backplate. The special back cover contains all the electronics and contact pins to connect with the phones battery.
looks like it make the phone super thick!!! Plus cant use with any cases
jerflash said:
looks like it make the phone super thick!!! Plus cant use with any cases
Click to expand...
Click to collapse
Of course, they have to place the coil somewhere, it's just a sacrifice you have to make for having the convenience. Also most flexable rubber/silicone cases do work because they stretch (I just prefer to go without them for the sake of ruining the design of the phone).
It should be arriving here by end of week and I'll be sure to take a few pics for you guys.
FYI, I have purchased a wireless charging back for every single Samsung device I have ever owned so I have plenty of experience (S3, S4, Note 3, and currently S5)
I was running the wireless charging back on my LG G3 so I have some experience as well. That back only added 1 millimeter to the thickness...I measured it. Just better design. I have the alpha and I'm currently testing next to the iPhone 6. Liking both phones alot. Need to test battery life
Sent from iPhone I'm testing using Tapatalk
The most disappointing thing about the wireless charging back cover, other than its extra thickness which makes it less flush, is on the standard cover, the SAMSUNG logo is shiny and embossed, giving the same effect as the metallic edging. On the wireless charging cover, its matte and flat like a cheap tacky plastic print. Not at all in-keeping with the quality of the rest of the phone.
BunnyKillBot said:
The most disappointing thing about the wireless charging back cover, other than its extra thickness which makes it less flush, is on the standard cover, the SAMSUNG logo is shiny and embossed, giving the same effect as the metallic edging. On the wireless charging cover, its matte and flat like a cheap tacky plastic print. Not at all in-keeping with the quality of the rest of the phone.
Click to expand...
Click to collapse
Hmm this is quite strange, usually Samsung does not cheap out on those wireless charging back covers and try to make it as identical to original as possible (at least on all the models I've used them on). Perhaps they didn't spend as much into this one due to the lack of popularity/demand for this device. Still surprises me though, it should cost cheaper in that case as well.
@jerflash: Actually on the S5 the gain in thickness is almost not noticeable. My dad uses one and switched backcovers and you don't see it.
Inductive coils are super thin copperwires that need next to no room for themselves.
I bought one of these for my note 3 and even though it did give it some weight and thickness, the battery cover was thick enough that the camera lens would not come in contact when places on a flat surface which was nice.
BunnyKillBot said:
The most disappointing thing about the wireless charging back cover, other than its extra thickness which makes it less flush, is on the standard cover, the SAMSUNG logo is shiny and embossed, giving the same effect as the metallic edging. On the wireless charging cover, its matte and flat like a cheap tacky plastic print. Not at all in-keeping with the quality of the rest of the phone.
Click to expand...
Click to collapse
That is the wireless charging cover of the Alpha right? Can you tell me if it has magnets in it for alignment? I'm trying to build a car dock with magnetic attachment like the Nexus 5 and wonder if this cover for the Alpha would let me do that.
---------- Post added at 11:41 PM ---------- Previous post was at 11:16 PM ----------
open1your1eyes0 said:
Of course, they have to place the coil somewhere, it's just a sacrifice you have to make for having the convenience. Also most flexable rubber/silicone cases do work because they stretch (I just prefer to go without them for the sake of ruining the design of the phone).
It should be arriving here by end of week and I'll be sure to take a few pics for you guys.
FYI, I have purchased a wireless charging back for every single Samsung device I have ever owned so I have plenty of experience (S3, S4, Note 3, and currently S5)
Click to expand...
Click to collapse
And/or would you know the answer to my question?
Is anyone using the qi cover with thr Alpha?
imthenachoman said:
Is anyone using the qi cover with thr Alpha?
Click to expand...
Click to collapse
I am. As far as am aware there are no magnets in the cover but a metal plate is there.
open1your1eyes0 said:
I am. As far as am aware there are no magnets in the cover but a metal plate is there.
Click to expand...
Click to collapse
And it works? I emailed Samsung and they told me there are no qi chafgers that work with the Alpha. If youre saying it works I might actually buy it and build a magnetic charger for it so I can dock in my car. Thanks!
They also confirmed thr Alpha has OIS.
imthenachoman said:
And it works? I emailed Samsung and they told me there are no qi chafgers that work with the Alpha. If youre saying it works I might actually buy it and build a magnetic charger for it so I can dock in my car. Thanks!
They also confirmed thr Alpha has OIS.
Click to expand...
Click to collapse
It definitely works (using it daily at work) so whoever you talked to has no idea what they're talking about. Wouldn't be the first time honestly.
That wireless charging cover looks super ugly and so doesn't fit the amazing design of the rest of the pone. Not sure what Samsung was thinking when making such a poor looking charging cover.
imthenachoman said:
And it works? I emailed Samsung and they told me there are no qi chafgers that work with the Alpha. If youre saying it works I might actually buy it and build a magnetic charger for it so I can dock in my car. Thanks!
They also confirmed thr Alpha has OIS.
Click to expand...
Click to collapse
Thay confirmed OIS,i try to find out anywhere this info but I only find in one US site nowhere else
is it possable that Alpha has OIS
Can you shere this info with us m8
Could you please tell me whether the extra thickness of the cover makes it impossible to fit a case over it? I have in mind a flip case.
Samsung do not yet list a wireless charging back on their web site for the Galaxy Alpha. I wonder if this is a picture of the back for the bigger battery.
I got my official wireless charging back. Unfortunately, it does make the phone slightly thicker which means cases are not going to fit over it. I tried a cheap plastic soft case which I thought would stretch enough to fit but it didn't. So I had better not drop my phone.....
Otherwise, the wireless charging works fine with a Nokia DT desktop charger.
I wanted wireless charging, but the only one available (from fonesalesman.com) costs about $80USD to my door.
So, I bought an S5 pad and used some copper tape I had lying around. NOTE: Copper tape (or at least the one I have) is only conductive on one side because of the adhesive. I rolled the ends up to make large contacts for the terminals on the phone and wireless charging pad.
I also removed the golden pins from the wireless charging pad because they were a bit thick. If you do this, be careful not to remove the silver pad underneath (I almost did).
See pictures attached, they're pretty explanatory.
The current pad I am using is a bit thick, and have ordered a new one, but it works! And it doesn't cost the earth.
Hope this helps people.
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
How does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
killbom said:
how does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
Click to expand...
Click to collapse
hi res picture 3mb
Thumb:
Hey guys,
It doesn't look as good as the post from DimonVideo, but as I said, I'm waiting on a thinner wireless model.
I'll put some pictures up later when I get home.
0.5mm Receiver
novastorm17 said:
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
Click to expand...
Click to collapse
I'm planning on getting this one.
Can't post the link to amazon as I do not have the minimum posts to do so.
Search this:
Alpha SlimPWRcard - 0.5mm Qi Receiver for Samsung Galaxy Alpha with integrated NFC coil
Those are the only model available for the Alpha. But since I don't live in USA, it would cost at least $50USD for me. So, I put together this thing
Where you get the pinout of the alpha wireless charger?