Hi, I was using my S2 with CM 10.1.3 with no problems. For modem reasons, I decided to go back to Gingerbread (UCKH7). Everything was susessful. But when battery level was low, I connected it to wall charger (Turned on). 3 seconds later, my phone turns off and shows the battery with the 5 dots. My phone goes up to the fifth dot and reboots.
Tomorrow (if I can), I am going to upload a video.
Thank you.
Bootloader? Nope.
I tried updating to UCMD8 4.1.2 (To see if it was the bootloader) but nothing happened...
NOTE: I'm preparing the video.
http://y2u.be/76VqYcxD0sQ
Solved! installing SHOstock 3
Related
I flashed the latest builds from both Coffebeans - http://forum.xda-developers.com/showthread.php?t=1547778 and Pershoot - http://droidbasement.com/galaxy/roms/cm9/p4wifi/ and I'm having the same issue with both of them. The problem is my Tab will randomly reboot then get stuck on the boot animation and just sit there forever. It's already happened twice now where my Tab rebooted sometime at night and sat at the boot animation until the battery was dead. I did do a full wipe before flashing.
Does anyone else have this issue?
Thanks.
i've ran both of those without any problems. did you come from another custom rom or from stock firmware?
foliage green said:
i've ran both of those without any problems. did you come from another custom rom or from stock firmware?
Click to expand...
Click to collapse
I came from Task650's version 14, but I've been flashing the CM9 KANGs for a while and haven't had this issue.
i have had some strange reboots...but never gotten stuck on the boot animation like that..thats the bad part about not having a battery to yank unfortunately
Sent from a Gtab 10.1 running Build 30
Well whenever I can't get something to work right, I Odin stock firmware on it and restart the custom rom process from scratch. Having a clean slate is time consuming and might not even be necessary but it's the only full proof way I can get things to work.
I wiped everything and also formatted /system in CWM and then flashed Coffeebeans latest build from 4/8. I haven't had the reboot and stuck boot animation issue, but now I'm having an issue where every time I charge the tab fully it won't wake up. I have to hold the power button to reboot it. It seems like it's the deep sleep issue, but it's been fine leaving it overnight as long as it's not connected to the charger.
I install Resurrection Remix JB 3.1.4 rom into my s3 last nite and it went fine, can do whatever **** it usually does. When I woke up this morning, it can’t be turn on anymore although it is charging from the time I went to bed.
This is what I did for the pass 24 hours:
Device: gt-i9300, previous rom is wanam lite.
1. Use Super Backup to backup my SMS, contacts, and call log
2. Use titanium pro to back up all user app+data and backup Email 4.0
3. Save RR JB 3.1.4 to my extsd 8gb
4. Went in cwm make full backup
5. Cwm wipe dalvik cache, battery, and reset factory
6. Install RR JB 3.1.4 from extsd
7. Successful. Done all settings. Restore all user apps. All went smooth.
8. Restore Email 4.0. Got forced close, but I just **** it. Reboot device, got forced close email again.
9. Play game, watch YouTube, facebooking, while charging the device.
10. Went to sleep with device charging.
11. Woke up this morning, device with green led on, unplug it, green led light when off, phone can’t turn on.
12. Tried to press here and there but nothing happens.
13. Grabbed my hair, bang my head on the wall, and shouted “fuuuuccccckkkkkkkk”.
14. Typing this post.
Any kind soul out there, please lead my s3 to the path of light….. Thanks in advance.
Have you flashed the ELLA bootloader?
This sounds like sudden death, check out the threads in General. But first, try replacing the battery and the charger
Glebun said:
Have you flashed the ELLA bootloader?
This sounds like sudden death, check out the threads in General. But first, try replacing the battery and the charger
Click to expand...
Click to collapse
Lol, sort of sudden death..... I don't know what is ELLA boot loader so I'm sure I didn't do anything about it. I plugged in my charger but the led didn't turn on and nothing appear on the screen. I will try to change other battery to test it. If it still doesn't work, I think it's called "freaking sudden bricked".....
Thanks for ur reply.
Samsung will repair it under warranty.
I'm sorry to say but you have the sds...
Verzonden door mijn GT-I9300 met xda premium
, it can’t be turn on anymore although it is charging from the time I went to bed.
Common issue of Sudden Death reports = overnight charge .
jje
I have a serious issue with both my I9100 devices.
it suddenly freezes and requires reboot. when i do it, it stuck on boot screen (Where the yellow triangle would be if using unofficial firmware)
nothing helps, only wipe data. once I wipe, device loads fine and starts working again.
I tought at first its rom/kernel related, I switched everything and even tried stock rom.
it keeps happening...today, I tried to swap batteries as one got empty, I took the battery out of the stocked-rom device (after turning it off) and then later when i switched it on, it had to be wiped.
same as with my other device.
Anyone has any clue what this is about?
Its became a big issue for me, I cant flash/wipe every few days...
One device is on Neatrom 4.4 lite, the other stock-everything, both 4.1.2
eranyanay said:
I have a serious issue with both my I9100 devices.
it suddenly freezes and requires reboot. when i do it, it stuck on boot screen (Where the yellow triangle would be if using unofficial firmware)
nothing helps, only wipe data. once I wipe, device loads fine and starts working again.
I tought at first its rom/kernel related, I switched everything and even tried stock rom.
it keeps happening...today, I tried to swap batteries as one got empty, I took the battery out of the stocked-rom device (after turning it off) and then later when i switched it on, it had to be wiped.
same as with my other device.
Anyone has any clue what this is about?
Its became a big issue for me, I cant flash/wipe every few days...
One device is on Neatrom 4.4 lite, the other stock-everything, both 4.1.2
Click to expand...
Click to collapse
u can just rewert to stock ICS 4.0.3 firmware on both the phones and check for the issue (whether its firmware related or any hardware issue as such)
thanks for your help,
It did not happen on 403, tough it didnt happen on 4.1.2 for some while either.
what else would you suggest me to test?
eranyanay said:
thanks for your help,
It did not happen on 403, tough it didnt happen on 4.1.2 for some while either.
what else would you suggest me to test?
Click to expand...
Click to collapse
1) with 403 for some time once again to ensure no issues of freezing.
2)then a different 4.1.2 stock/custom rom altogether to check for the same(freezing) issue.
stay for some time on those firmwares and see (may be one or two charge cycles).
3) do not install any mods on top of the firmware, just stay stock and see
One of the devices is already back to 403, while the second one on stock 412
the hardest thing to tell if 403 solves it or not, as it happens occasionally, once in a week or two.
I tried two different stock roms, so that would rule out #2.
The weird thing is that wiping data is enough.
data is separated from the rom itself, yet it causes the entire device not to boot anymore.
I'am having xperia mini pro ( mango ). Several weeks I was using FXP's CM 7.2, later decided to try LegacyXperia's CM 10.1, Installed it perfectly. Later that day noticed my battery drains very fast.. like 1 percent per 2~4 minutes. Thought to go back to CM 7.2, reflashed back succesfuly and the bug apeared.. I charged my phone to 100 percents, disconnected charger and battery drained to 0 per few seconds, phone turned off, tryed to turn on, but only red light keeps blinking. Connected to charger again, turned phone on, it says "charged" and 100 percent, but after disconnecting charger it dies again, can be my battery damaged or something? Tryed to wipe battery stats and clean phone under battery, nothing helps yet, any suggestions?
BlackIliusion. said:
I'am having xperia mini pro ( mango ). Several weeks I was using FXP's CM 7.2, later decided to try LegacyXperia's CM 10.1, Installed it perfectly. Later that day noticed my battery drains very fast.. like 1 percent per 2~4 minutes. Thought to go back to CM 7.2, reflashed back succesfuly and the bug apeared.. I charged my phone to 100 percents, disconnected charger and battery drained to 0 per few seconds, phone turned off, tryed to turn on, but only red light keeps blinking. Connected to charger again, turned phone on, it says "charged" and 100 percent, but after disconnecting charger it dies again, can be my battery damaged or something? Tryed to wipe battery stats and clean phone under battery, nothing helps yet, any suggestions?
Click to expand...
Click to collapse
Try flashing your stock firmware with Flashtool. See if things are okay. If so, flash Rage kernel for CM7 (using command and not flashtool) and then install CM7. Rage kernel gets the best battery life in my opinion. Note that there are two Rage kernels. One for stock firmware and another for CM.
dvijaydev46 said:
Try flashing your stock firmware with Flashtool. See if things are okay. If so, flash Rage kernel for CM7 (using command and not flashtool) and then install CM7. Rage kernel gets the best battery life in my opinion. Note that there are two Rage kernels. One for stock firmware and another for CM.
Click to expand...
Click to collapse
Huge thanks, flashed stock ICS via flashtool and my battery is working normaly! :victory:
Q Problem with Xperia Active
I try to install cm 9.1 on my phone.I go in CWM and:
1. Wipe Data/Factory Reset + Wipe Cache partition
2. Mount System + Storage
Format System
Format Data
Format Cache
Wipe Dalvik Cache
and when i try to install zip from SD i cant open SDI restart the phone but it did not turn on.Now can not access the CWM.
Is someone can help me, or are looking to what I've got brick smaller dimenzija
Change your kernel (you can find kernels here)
Hello Devs,
I have problem charging my s3 international version.
My phone is rooted and running custom rom s5 sensation v4.0 kitkat 4.4.2 with boeffla kernel v6.0 and latest CWM touch recovery.
I have flashed many custom roms before and all was working good before. The phone was also charging properly before.
But after some time when 4.3 was released I have flashed s4 revolution.
After flashing that rom my problem started.
1st problem was the phone was not gettin connected to my cell tower. Later after searching soo many hours on google I found out that it changed the efs version from v1 to v2. So I found out a rescue zip file which include only modem of xxemg4. I flashed it and then all was working good.
After some time I faced a problem of reverse charging means the phone is kept on charge but instead of charging the battery decrease. So again I searched on google about my problem and found out an app called galaxy charging current which show the power that is getting the phone while its connected to the charger. when I installed it and saw the current it was only showing max 100 min 999 and avg 100. I saw some where that the default current the phone should get is 1000 in max.
I searched alot on google on how to solve this problem, tried many diffrent rom , tried changing my charger, tried to flash back the previous rom which I was using in which I was not having any problem but after doing all this the result was same.
when I connect to the charger it shows 700 In max n after some time it keeps going down like 500 then 300 then last 100.
So after searching on google I have found out a solution of flashing custom kernel. I flashed googymax kernel in which using sTweak we can configure the battery power and ignore safety measures and unstable power.
After doing that my phone gets max 1000 min 1000 and avg 999.
My problem is that when ever I flash new rom I hav to flash custom kernel to ignore the unstable power and safety measures to properly charge my phone.
is there any way I can get back as before I was charging my phone without flashing custom kernel...???
Any answer will be appreciated.
Note :- I was using the original charger which I got in the box while purchasing.
First replace your battery, charger and lead, then flash full stock firmware with Odin.
What happens when you attempt to charge the phone completely off. Do you see the charging graphic?
If something is wrong with the micro-USB port then a wireless charging solution might be your only option.
You could try reloading the firmware using the Kies software on your PC - here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)
Thnaks for your rply
boomboomer said:
First replace your battery, charger and lead, then flash full stock firmware with Odin.
Click to expand...
Click to collapse
1st of all thanks for replying on my query.
As u stated to change the battery, Charger, Lead and to full flash stock firmware.
I already did that.
I have tried my friends battery with his charger ( not the 1 which come in box ).
but then also its the same.
Whats the problem in it.
Is it a software fault or hardware fault....???
Hermosa said:
What happens when you attempt to charge the phone completely off. Do you see the charging graphic?
If something is wrong with the micro-USB port then a wireless charging solution might be your only option.
You could try reloading the firmware using the Kies software on your PC - here's an overview of what to do:
- if you don't already have the Kies software installed on your PC, download it (just search Google) and install it. The first time it runs it'll update itself to the latest version so make sure you run it once before proceeding.
- put your phone in Download mode: with the phone completely off, press and hold the Volume Down and Home and Power buttons simultaneously, and release them all when you see the Samsung splash screen
- connect the phone to your PC with the USB cable that came with the phone
-- if you've never had the phone connected to your Windows-based computer before, you'll see messages about installing drivers, etc - just wait until this is done (may take 5 or 10 minutes) [I don't know what happens if you have a Mac - it probably just works]
- in the Kies software, select the second item in the Tools menu and just follow the prompts to enter the model number (in CAPS) and IMEI/Serial Number (both found under the battery - it's ok to remove the battery at this point)
- the Kies software should start downloading the correct firmware for your phone from the Internet; once that's done (depending on your Internet connection speed) it'll begin downloading that to the phone (this probably takes 10 minutes or so)
Click to expand...
Click to collapse
Thanks for the reply.
When I try to charge my phone when completely off, 1st it was showing me the graphics of battery charging when I was using 4.3 Custom Rom. But since I flashed my phone with 4.4 Custom Rom, I can't see the graphics of charging battery now.
As per your overview above I have tried all the possible ways to get back charging work properly ( your overview was also included in it ) but I dont get any success in it.
Now I have to compulsory flash custom kernel which supports the options of ignoring unstable power and safety measures.
But then also I will try to do what you told me.
Once again thanks.