Hello. I'm new here. and not native speaker.
I'll try my best for English.
My device got soft bricked after I'm trying to install the new ROM.
Actually I had installed the ROM but It didn't appear anything.
Then I'd try to restore my backup to Its place.
It made my phone brick.
I can't boot into recovery mode, ROM and also FTM mode.
I must have an access to adb, If I want to boot into bootloader.
But I don't have any access to it at all!!.
I had read some post and I hope that DFU can help me.
But I don't know how can I boot into that mode.
And I had try hold volume + and - with and without power button but it still the same.
I had read that the DFU mode will display nothing but have the briefly red led.
I had accident plug the USB to device without battery.
And I got it, The briefly red led light with nothing change in the display (still nothing).
My computer recognizes it as a ZTE technology device. But It's in an unspecified device zone.
I had installed the ZTE USB device (My computer is MS Windows 8.1) and I had also installed it with unsigned driver mode too.
What could I do for getting it to work again?
Have I found the correct DFU mode?
My device is ZTE V817.
With MSM8225Q CPU and MSM7627A board platform specified in default.prop.
Related
Some wanker had posted wrong images for boot and recovery for S6000L. And since I'm a moron, i didn't take the files apart to check them.
Installing them bricked my tablet. So essentially I have no boot or recovery images on the device and was wondering if there's any way to revive it.
Tablet freezes if i start it in normal, fastboot or recovery modes, so that's out of the picture.
However, i think that "meta mode" still works (if indication of it working is displaying lenovo logo and having "meta mode" written on the bottom of the screen)
It's getting detected on "mediatek preloader usb vcom port" for a couple of seconds when connected to the PC, which means that i might be able to use adb to push a backup into the tablet (?)
Been scouring the internet for a while with no results. Is there, by any chance, anyone who can help me out?
Hi Guys,
I'm in a bit of a problem. I bricked my phone and nothing seem to help.
Let me tell whats happened
1. I updated my TWRP in LeTV X500
2. This kinda made my phone to in soft brick mode every time I restarted it went to TWRP
3. I than installed new ROM from TWRP (i think it might be too high for my phone)
4. Phone endup bricked, not switching on, off nothing - redl light only
5. I tried here to install new rom from Windows and Linux via SP Flash Tools - phone is not recognised.
6. I disassembled the phone and detached battery
- now this is actually helped in a way that windows now recognises the phone, but the connection is not continous
- it recognises MediaTek Pre launcher ... few seconds pass
- it disconnets the MT Pre Launcher
- It recognises VCOM USB Port ... few seconds pass
- It disconnets again
- loop like this goes on and on
7. I tried holding any of the buttons (up, down, power and combination) - not helping
8. I believe my last option is to try and bridge some of the points on the motherboard to try and reset the system ... is this correct?
I have no idea what should I bridge with what ... there are no labels on the MB, i'm not even sure where the GND is.
Any ideas fellas?
Here is front of the MB:
Code:
imgur.com/a/b4oWI
Here is back of MB
Code:
imgur.com/a/XgZiV
help will be appreciated
Have you found a solution?
hi. so my problem is that my phone does not turn on, i cant go to recovery or do hard reset. the phone react when i plug it in PC without battery, but its always connect and disconnect over and over again. i have downloaded the omap drivers and instaled it. now i have in the device manager a OMAP4430 FastBoot USB device. by the drivers was a fastboot emulator. but when i will flash rom, kernel or recovery a just get partition does not exist. can someone help me please? srry for english.
Does your phone not turn on at all when holding down the power button? If it boots up, and gets stuck on a loop or has an error message, that is different. But if it doesn't turn on at all, then your battery is dead or something is wrong with your phone's hardware. If you connect your phone to the PC (with the battery on), does it at least show a light? Or does it boot up at all when you hold the power button? If it doesn't show a light or boot up, it is not your battery, but your phone's hardware. Your phone might have been dropped or water inside it or it was microwaved? I know it sounds silly, but something happened to the phone physically. Now if you connect it to the PC and you see a light but it never boots, your device is bricked. Not accusing you, but you might have tried rooting it or writing over a partition on your phone which caused to brick. Also, try typing in fastboot devices. If it shows up a device, that means it is connected. Cheers!
No the phone does not turn on and it shows nothing, even when i put it on charger. If i connect to pc with battery after i installed the omap driver it just connect and disconnect over and over again, windows make this sound when you connect and disconnect something. I have flashed a new rom. It has worked but after some time its stoped. So i have try flashed it again but i could not get in recovery. A files was missing and after i try flashing thhe recovery its just dead. I can connect it just with the fastboot emulator because it's don't connect when i just put it on pc. I must connect it without battery wait 4 sec and then put the battery back. Than i can see in the emu my phone but not able flash anything because of partition does not exist
Hi,
I've got a Nubia N1 Lite (NX597J) to mess around with, and wanted to try modifying the ROM. I can enter developer mode and allow bootloader unlocking, adb also works. What I can't do is use USB while booting, or in the recovery menu. No fastboot or sending ROM images via adb to the recovery software. The phone doesn't connect to the computer at all (I'm using Linux, it should at least show up in dmesg). Recovery log says
Code:
musb_pullup 2498: no USB cable, don't need to turn on USB
A couple times, even though the cable is connected and works in Android proper. I've tried USB2 and 3 ports, on a hub and directly on the motherboard. It shows up as 0e8d:2000 MediaTek preloader when turned off and, very briefly, as 0e8d:2008 when booting into recovery.
Am I missing something, or is the recovery image just broken on this phone? I've tried both the EU and US firmware, which is a bit more recent.
Do I need some tool that interacts with the preloader, maybe? I have found this guy who's been messing with a phone that has the same SoC.
Have you managed to get it into recovery mode? I just get a dead android picture :/
I've accidentally broken it by flashing the US ROM but my phone is the EU version. Boots up okay but has lost the IMEI and once the screen turns off won't turn on again - unless I reboot it.
Have so far failed to re-flash with the correct EU ROM - it just fails half-way through.
No, and I'm in the same situation with the firmware.
Hello there. Today i found my old Huawei G6 in a drawer and i wanted to use it as a backup phone. But when i tried to power it on i would get a recovery, boot image failed. So i searched and finded that i need to put a firmware on SDcard and then hold some buttons and flash it. But i was stoopid and downloaded the B189 firmware which is famous for bricking devices. The phone updated, rebooted and was dead. It didnt react to buttons or combinations or even charger. I tried Qfil which was succesful but still the phone doesnt power on. Then i tried Huawei Smartphone Multi Download Tool that would say that port isnt ready. Even some chinese programs i getted reccomended. The phone is in Qualcomm HS-USB-9008 mode. Thanks for any anwsers.
@Andys4c
It seems phone's USB-connection is configured as MTP ( Media Transfer Protocol ) mode and not as ADB ( Android Debug Bridge ) mode