I know there has been other treads about this before but none of the suggestions seemed to work for me. I searched and searched and I'm just not finding a fix. I hate to do these posts when an easy answer is right there but I just can't figure it out and it's killing me. So here it is:
I just got this Verizon Galaxy Tab that would not come on - only showed the battery charging icon. I just charged it over night and it came on once. However, processes kept shutting down. For instance, when I went into settings and tried to connect to my wifi network, the whole process would just close down. So I let it get to about 40% and reboot it to download mode (there was no recovery). I found the correct .tar file for it and flashed it with ODIN3 v1.85. It completed successfully but now it won't boot past the Samsung splash screen. Once the splash screen comes up, it will just go back to the large battery charging icon in the middle of the screen.
Then I tried the other option where you get into recovery and nothing happens at all. The screen is backlit black (you can just see light around the edges of the screen) and nothing ever happens.
So now, it's just charging but it seems to charge very slowly. I was wondering if this is a battery issue or some strange sequence that needs to be done. It seems to be at about 40% again. Any other suggestions would be appreciated.
These are other things I've tried:
hold the power button down for 30 seconds
Hold the power button down while touching the screen
More suggestions would be appreciated.
Now the tablet is fully charged but it still gets stuck on the splash screen when trying to boot up. Still have no recovery. Also, I'm not able to find a PIT file to re-partition. Can someone tell me how to get the stock recovery back at least? I've been looking but I can't find a file to flash for the recovery.
Same problem
Hi, I have the same issue basically. I have the Galaxy Tab SGH i957D 8.9 (TELUS) and flashed it to root last night, now I have the same problem. Except I have CWM installed, I was able to install that AFTER I locked it up. Help from one of the GURUs here would be great. It's obviously a problem caused by flashing it.
So try flashing with CWM, at least you'll have a good recovery on it. If we work together, we may be able to come up with a solution for our dilemma. I don't believe it;s a major problem, I had the same issue with my captivate phone when trying to CWM and Cyanogenmod, and I got it working perfectly, so there is hope.
I have tried the stock rom, rooted rom, and a couple of others, but still can;t get past the splash screens. Left it overnight trying to boot, and all it did was kill the battery. I can;t even turn it off, it just reboots every time I try shutting down. I CAN get to download and recovery mode though, and flash it all I want with Odin 3.7 and 1.83, just never boots past the splash screens.
DermagraFX said:
Hi, I have the same issue basically. I have the Galaxy Tab SGH i957D 8.9 (TELUS) and flashed it to root last night, now I have the same problem. Except I have CWM installed, I was able to install that AFTER I locked it up. Help from one of the GURUs here would be great. It's obviously a problem caused by flashing it.
So try flashing with CWM, at least you'll have a good recovery on it. If we work together, we may be able to come up with a solution for our dilemma. I don't believe it;s a major problem, I had the same issue with my captivate phone when trying to CWM and Cyanogenmod, and I got it working perfectly, so there is hope.
I have tried the stock rom, rooted rom, and a couple of others, but still can;t get past the splash screens. Left it overnight trying to boot, and all it did was kill the battery. I can;t even turn it off, it just reboots every time I try shutting down. I CAN get to download and recovery mode though, and flash it all I want with Odin 3.7 and 1.83, just never boots past the splash screens.
Click to expand...
Click to collapse
Thanx for the reply. As you can see, I've been around these forums for a long time and usually I'm able to work it out but this one has got me stumped. Just wanted to ask you if you have tried to flash a custom ROM in Clockwork? Also, did you go through unlocking the boot loader befor you flashed it? I did not because I received the tablet in this condition. I tried to flash clockwork mod but I get an "invalid file" error in Odin. Once I flashed the stock recovery and it worked fine. But after reflashing the stock rom, the stock recovery is gone now. Do you have a link to the files you used? I'm thinking that the stock recovery is messed up but I can only find that one file.
no I haven't tried flashing through CWM, as I wasn't trying to flash originally, I was just rooting and going easy on it, then it wouldn't boot, so I wasn't prepared and now can't add files to my SD drive.
I didn't unlock the boot, as none of the instructions I read mentioned it (rooting was all I was trying to do).
I don't even have a stock recovery either, all I have is CWM and TWRP.
I'm going to try mounting it in Linux and see if that makes any difference to put roms on my SD drive, as windows doesn't like it anymore, except through Odin, where luckily it seems to work fine... For now.. lol
Fixed!!!
shawndh said:
Thanx for the reply. As you can see, I've been around these forums for a long time and usually I'm able to work it out but this one has got me stumped. Just wanted to ask you if you have tried to flash a custom ROM in Clockwork? Also, did you go through unlocking the boot loader befor you flashed it? I did not because I received the tablet in this condition. I tried to flash clockwork mod but I get an "invalid file" error in Odin. Once I flashed the stock recovery and it worked fine. But after reflashing the stock rom, the stock recovery is gone now. Do you have a link to the files you used? I'm thinking that the stock recovery is messed up but I can only find that one file.
Click to expand...
Click to collapse
ok.. I have mine fixed and running again.
http://samsung-updates.com/device/?id=SGH-I957D
This is the stock flash/rom for Telus on the SGH i957D LTE 4G 8.9 model. Try samsung-updates.com and search for your exact model and carrier.
-Download correct stock image for your tablet.
-Unpack the file you downloaded
-Put your device in DOWNLOAD mode
-Connect it to Computer
-Start ODIN and wait for the COMM status to show as connected
-In PDA box navigate to your file and add it to the box.
-Press start
-Sit back and relax.
-Enjoy the fireworks as your tablet comes back to life..
-YEAH!!!
Life is good again...
DermagraFX said:
ok.. I have mine fixed and running again.
http://samsung-updates.com/device/?id=SGH-I957D
This is the stock flash/rom for Telus on the SGH i957D LTE 4G 8.9 model. Try samsung-updates.com and search for your exact model and carrier.
-Download correct stock image for your tablet.
-Unpack the file you downloaded
-Put your device in DOWNLOAD mode
-Connect it to Computer
-Start ODIN and wait for the COMM status to show as connected
-In PDA box navigate to your file and add it to the box.
-Press start
-Sit back and relax.
-Enjoy the fireworks as your tablet comes back to life..
-YEAH!!!
Life is good again...
Click to expand...
Click to collapse
I'm glad you got the right firmware and fixed your tab! But this site does not list a firmware for the SCH–i905 anywhere. Unless the Verizon Galaxy tab has an alternate model# there is no firmware on the site for my device. Oh well, at least one of us got tablets fixed. Congrats!
Download mode issue.
What recommendations do you guys have for a tablet that will not recognize in download mode?
I accidently flashed a bootloader and had auto reboot on - couldnt flash kernel and modem in time.
My tablet fully boots up, (rom manager says cwm is installed) as well as when i boot into recovery its completely black.
My main concern is that download mode is not recognized. it was previously working prior to installing the bootloader.
What can i do to fix this issue?
younggunner said:
What recommendations do you guys have for a tablet that will not recognize in download mode?
I accidently flashed a bootloader and had auto reboot on - couldnt flash kernel and modem in time.
My tablet fully boots up, (rom manager says cwm is installed) as well as when i boot into recovery its completely black.
My main concern is that download mode is not recognized. it was previously working prior to installing the bootloader.
What can i do to fix this issue?
Click to expand...
Click to collapse
Can you start by giving as much info as possible about your tab, make model# etc.
can you actually get into download mode? Power button and Volume down button till it boots then release pwr.
you may have bad drivers on your pc. I had this problem with my phone when I installed CM.
get into DL mode and then start Odin and hopefully you will see the Com port attached.
then in PDA load the stock rom for your tab.
hopefully at this point youll be all set.
if your tab is fully functional, then try just flashing CWM or TWPR to your tab. I found with mine that CWM works best. I like TWP better for looks and the touchscreen functionality, but I found it gets a bit flaky after a few flashes, where CWM seems more stable.
SHAWNDH...
give me all your info for your tab, make, model.. carrier etc. as much as you can, and I will see if I can find any stock roms while doing my searches. 2 sets of eyes are better than one...
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
younggunner said:
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
Click to expand...
Click to collapse
I don't get it. First, you can't flash a kernel using Odin. Second, your tab won't even be able to boot without the kernel.
Sent from my GT-P7500 using Tapatalk HD
younggunner said:
So i have a sch-i905, 4.0.4 - I CAN boot into normal android
I flashed a bootloader last night and had auto reboot ticked. was not able to install the modem or the kernel.
I can get into download mode without any issues,but now download mode says "waiting for cable" and is not recognized by pc as it once was prior to the flash.
I can also get into recovery but its completely black ( assuming due to no kernel flashed )
I can get into android normally, but cant fix firmware through download mode, and recovery.
Please help :X
side note: rom manager says twmp and cwm is installed, though i get no display in recovery only blackness
if i can get download mode to work again or get cwm to show up i can fix it, but dont know where to go from here.
Click to expand...
Click to collapse
If you can get into DL mode, then its probably just an issue of drivers on your pc. Download the samsung drivers and reinstall.
Then put your tab in dl mode. Then connect to the pc with cable, try a different usb port than before.
Then start odin, if you get the Com port showing up in the status box, then flash CWM recovery to the tab. Then start over with what you are trying to do. But I can almost garantee its an issue with drivers on your pc. I had the exact same problem with my phone when I did it,
and fixing drivers was the issue. I wss stumped for a long time on that issue. If that doesnt work, look into Heimdall flash utility or Kies and go from there.
Hope this helps. Or at least gets you on the right track.
update
DermagraFX said:
If you can get into DL mode, then its probably just an issue of drivers on your pc. Download the samsung drivers and reinstall.
Then put your tab in dl mode. Then connect to the pc with cable, try a different usb port than before.
Then start odin, if you get the Com port showing up in the status box, then flash CWM recovery to the tab. Then start over with what you are trying to do. But I can almost garantee its an issue with drivers on your pc. I had the exact same problem with my phone when I did it,
and fixing drivers was the issue. I wss stumped for a long time on that issue. If that doesnt work, look into Heimdall flash utility or Kies and go from there.
Hope this helps. Or at least gets you on the right track.
Click to expand...
Click to collapse
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
---------- Post added at 12:24 AM ---------- Previous post was at 12:22 AM ----------
younggunner said:
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
Click to expand...
Click to collapse
Ive tried another pc as well. I dont believe its a driver issue as there is 0 interaction in download mode with device manager. but prior it easily was detected in odin no issues.
younggunner said:
dont think its a driver issue.
it was working fine in download mode prior to me flashing a bootloader.bin, and yes you can flash a kernel.bin through odin, as well as a modem.bin.
I was in the process of installing cwm this way when it happened.
I can get into the os, i can get adb working fine, recovery is just a black screen though it goes into it. and i can get into download mode still, just stuck at "waiting for cable" no interaction with device manager
---------- Post added at 12:24 AM ---------- Previous post was at 12:22 AM ----------
Ive tried another pc as well. I dont believe its a driver issue as there is 0 interaction in download mode with device manager. but prior it easily was detected in odin no issues.
Click to expand...
Click to collapse
Ok... Im getting confused here... You Can still flash with Odin? Then you can install a new recovery on it. If device manager on the pc is not working, then you probably have a corrupt install, or the wrong rom file for your particular tab, and the usb drivers arent correct for your tablet.
Personally, I would start by downloading a stock rom file and return the tab to factory before starting anything, so you have it working as it should before continuing further.
If you DO HAVE a stock rom, maybe you could pass it along, i believe shawndh who started this thread is in need of one for the same tablet.
confusion fixed
DermagraFX said:
Ok... Im getting confused here... You Can still flash with Odin? Then you can install a new recovery on it. If device manager on the pc is not working, then you probably have a corrupt install, or the wrong rom file for your particular tab, and the usb drivers arent correct for your tablet.
Personally, I would start by downloading a stock rom file and return the tab to factory before starting anything, so you have it working as it should before continuing further.
Click to expand...
Click to collapse
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
younggunner said:
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
Click to expand...
Click to collapse
Oh... Well then it is beyond the scope of any problem I have encountered, or seen a solution to. I thought you could still connect in download mode.
Can you change usb debugging mode in tablet settings, that may enable you to connect? If not I dont think I personally can help, as your posts read like you could still use Odin.
On my phone, (galaxy S) nothing would connect after I messed up, but could do things with Heimdalls utility. See if you can connect with that. Worth a try, it does the same as Odin, but connects differently somehow.
DermagraFX said:
Oh... Well then it is beyond the scope of any problem I have encountered, or seen a solution to. I thought you could still connect in download mode.
Can you change usb debugging mode in tablet settings, that may enable you to connect? If not I dont think I personally can help, as your posts read like you could still use Odin.
On my phone, (galaxy S) nothing would connect after I messed up, but could do things with Heimdalls utility. See if you can connect with that. Worth a try, it does the same as Odin, but connects differently somehow.
Click to expand...
Click to collapse
i even went as far as getting a brand new cable to see if it was my cable still same thing. No response in download mode for either pc's ive tried.
little stumped....
possible clues: when tablet boots up, it boots up to a bright black screen, only once it completely boots up am i able to see my display properly.
DermagraFX said:
Can you start by giving as much info as possible about your tab, make model# etc.
can you actually get into download mode? Power button and Volume down button till it boots then release pwr.
you may have bad drivers on your pc. I had this problem with my phone when I installed CM.
get into DL mode and then start Odin and hopefully you will see the Com port attached.
then in PDA load the stock rom for your tab.
hopefully at this point youll be all set.
if your tab is fully functional, then try just flashing CWM or TWPR to your tab. I found with mine that CWM works best. I like TWP better for looks and the touchscreen functionality, but I found it gets a bit flaky after a few flashes, where CWM seems more stable.
SHAWNDH...
give me all your info for your tab, make, model.. carrier etc. as much as you can, and I will see if I can find any stock roms while doing my searches. 2 sets of eyes are better than one...
Click to expand...
Click to collapse
Thanx for the reply. I have the SCH-i905 32gb Galaxy 10.1 tab. The carrier is Verizon. I've spent days looking for another download source but I can only find one - there's a link from this site. Others have posted that it did restore their devices so I'm thinking that there are some bad clusters that need to be quarantined but I can't even find a tool for the Galaxy Tab that will do or check for that. I'd appreciate it if you could take a look though. Thanx.
younggunner said:
I cannot currently get download mode to recognize anything. just keeps saying "waiting for cable" thats why i cant do anything in download mode. It was currently working prior to flashing the bootloader through odin with the "auto reboot" accidentally clicked.
Click to expand...
Click to collapse
Are you connecting to a USB port that is on the motherboard of your computer? Mine will only recognize my tablet with one port. The other ports are not recognized at all by ODIN.
shawndh said:
Thanx for the reply. I have the SCH-i905 32gb Galaxy 10.1 tab. The carrier is Verizon. I've spent days looking another download source but I can only find one - there's a link from this site. Others have posted that it did restore their devices so I'm thinking that there are some bad clusters that need to be quarantined but I can't even find a tool for the Galaxy Tab that will do or check for that. I'd appreciate it if you could take a look though. Thanx.
Click to expand...
Click to collapse
I don't think its a cluster issue, just a bad flash previously. But you'll see from the link, yours is also known as the P4vzw. Well check the link and make sure that's your tab that I found. Then have a look at ALL the files for that tab.
Have you seen/tried this one... here's the thread STOCK ROM FOR YOUR TAB...
forum.xda-developers.com/showthread.php?t=1342995
Here's just the file.
http://goo.gl/XPMXv
Try flashing CWM recovery to your tab, and try a file from cyanogenmod
http://wiki.cyanogenmod.org/w/P4vzw_Info
Or just try the CM ROM first maybe and see what happens. I don't remember what you have for recovery. There are a bunch on there, but all nightly that I saw, but even that would be better than nothing for now if it works.
I'm still looking, but I know what you're saying about few and far between. I think they all are for the tabs. Let you know if I find anything else.
Another mod ROM. http://www.teamandroid.com/2012/08/...tab-101-sch-i905-android-411-aosp-jelly-bean/
Hi everybody, i need your help, yesterday i had a problem with mateo's unofficial cm10.1, after a reboot the phone freezes at LG logo, and if i try to get into the recovery it doesnt work cause it is writtene in the bottom "E: Can't mount /cache/recovery/command" and i do not have any button to select. So i try to go in SW Upgrade Mode but the pc is not able to recognize my phone like always did, i installed latest version of drivers but no way. In Lg mobile support tool doesnt work (look to te attached file). Any help?? :'(
Thanks in advance
Roker1 said:
Hi everybody, i need your help, yesterday i had a problem with mateo's unofficial cm10.1, after a reboot the phone freezes at LG logo, and if i try to get into the recovery it doesnt work cause it is writtene in the bottom "E: Can't mount /cache/recovery/command" and i do not have any button to select. So i try to go in SW Upgrade Mode but the pc is not able to recognize my phone like always did, i installed latest version of drivers but no way. In Lg mobile support tool doesnt work (look to te attached file). Any help?? :'(
Thanks in advance
Click to expand...
Click to collapse
But you get to S/W Upgrade Mode or not? If yes try diffrent computer too.
I am able to go in SW upgrade mode, but after 2-3 minutes the phone get off, i think the battery is out, is it possible? How can i charge it? The charge from phone turned off doesnt work in my last rom
Roker1 said:
I am able to go in SW upgrade mode, but after 2-3 minutes the phone get off, i think the battery is out, is it possible? How can i charge it? The charge from phone turned off doesnt work in my last rom
Click to expand...
Click to collapse
I think in that case you would need another working device to charge your own battery.
I'm using v40 of temasek unofficial cm11, Boefflea version 11 kernel.
while I was using my phone, the phone suddenly went into a reboot and started the boot-loop, even when I pull the battery out and put it back in it starts booting immediately and goes into the boot-loop , whenever I try to go into download mode or recovery mode, once or twice I will be able to reach it, but 3 seconds in, it restarts and goes into the boot loop again (I can't choose between restarting or going into download mode)
would a USB jig help me getting into the download mode or will it be 3 seconds in and restarts?
would a service center help me retain my data as I need them?
Thank you.
momentarily I've managed to be able to access download mode and the laptop started making a sound trying to identify the device, too bad the battery fell off (or the phone restarted) lol
anyways I still need help because I couldn't get into any of them
If the phone starts the moment a battery is inserted then usually the power button is stuck -try giving it a wiggle, or get it replaced.
boomboomer said:
If the phone starts the moment a battery is inserted then usually the power button is stuck -try giving it a wiggle, or get it replaced.
Click to expand...
Click to collapse
yeah will do that once this gets fixed lol ..
for some awkward reason, I found out that once I pull out the battery I can use download mode
what should I download?
I tried flashing CWM but I get back to the bootloop ... should I install a newer bootloader?
No, bootloader is irrelevant to firmware. You would be best to flash a full stock rom with odin then factory reset and see if it will boot. I would suspect the power cycling may have caused partition problems if recovery got wiped.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
No, bootloader is irrelevant to firmware. You would be best to flash a full stock rom with odin then factory reset and see if it will boot. I would suspect the power cycling may have caused partition problems if recovery got wiped.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
which would mean I would lose all the data in the previous cm11 right?
I'm trying my best to flash a recovery but I think it got wiped for good.. I'm trying to flash it over and over again .. (I unplug the battery once I'm in download mode to prevent the sudden restart) .. before I flashed the CWM through odin I was able to go into a glimpse of a recovery mode, now I can't seem to see it at all...
is there a way to just copy the data (mostly pictures) through odin or adb with my phone current state?
Google says it might be possible
http://codebin.co.uk/blog/samsung-galaxy-s3-boot-loop-backup-without-root/
boomboomer said:
Google says it might be possible
http://codebin.co.uk/blog/samsung-galaxy-s3-boot-loop-backup-without-root/
Click to expand...
Click to collapse
only through recovery mode or hoping your phone would suddenly connect after many boots lol
I don't think that will be my case .. oh well
as long as I can get my phone working again
going back to stock rom didn't fix the issue. can't access anything yet.
any help?
if anyone is reading this, I've been looking everywhere for a stock rom with pit file, I think that's the problem I'm facing since I have different bootloaders and different modes, somewhere around that I jacked my partitions and I think this would help putting it all back
I've found ones for android 4.1 but nothing of 4.3 .. since I came from 4.3 stock rom and then 4.4 kitkat temasek I think 4.1 won't help me at all
time to go to a service center I guess.
OK this is weird...
after I gave up I put my phone on a recover firmware that for some bizarre reason brought it back to life!!! I just put the phone back and left .. 5 hours later it was on and working.. I was able to access the phone for a brief moment.. but for some reason again I wasn't able to get the touch screen to work... I was able to raise the volume.. restart the phone.. but nothing on touch screen..
then it went back to the dead state...
any ideas?
@boomboomer
Motherboard component or connect lose or failing .
Hello same problema with mY S3 , the power button was damaged. and now I need to enter download mode to flash the firmware.... is there a way to enter download mode on S3 without using power key?
danieldp1990 said:
Hello same problema with mY S3 , the power button was damaged. and now I need to enter download mode to flash the firmware.... is there a way to enter download mode on S3 without using power key?
Click to expand...
Click to collapse
USB JIG
The story:
Got a phone with some software problems when calling from a spouse. Tried to update the ROM and it bricked.
Status:
endless loop of bootscreen
could enter recovery mode and boot CWR
can not enter download mode
unable to boot system
Tried endless guides and instructions with stock ROM's and firmwares. Some of them installed some didnt - none worked. Still in endless loop.
Gave up yesterday and went to bed to keep trying today.
Now its totally bricked.
- no recovery mode
- no download mode
- no boot screen
- cant connect to PC via USB (Odin wont recoqnize)
The only sign of life - whatever I do it has black screen with backlight on but nothing else.
What can I do? They say that a broken phone is only with hardware problems but could I have f**** up the software so much that its the same?
elisterr said:
The story:
Got a phone with some software problems when calling from a spouse. Tried to update the ROM and it bricked.
Status:
endless loop of bootscreen
could enter recovery mode and boot CWR
can not enter download mode
unable to boot system
Tried endless guides and instructions with stock ROM's and firmwares. Some of them installed some didnt - none worked. Still in endless loop.
Gave up yesterday and went to bed to keep trying today.
Now its totally bricked.
- no recovery mode
- no download mode
- no boot screen
- cant connect to PC via USB (Odin wont recoqnize)
The only sign of life - whatever I do it has black screen with backlight on but nothing else.
What can I do? They say that a broken phone is only with hardware problems but could I have f**** up the software so much that its the same?
Click to expand...
Click to collapse
You can try this guide by @SuperMini to force open Download Mode from odin. Here is the link,
How to unbrick Samsung Galaxy Ace
Make sure to use the key combination of Download Mode for your device as the one mentioned in the guide is for Samsung Galaxy Ace S5830. If that doesn't work, then you can try the USB Jig (not always guaranteed to work). If USB Jig did work, then it will force open the Download Mode so you can flash stock rom back using odin. If USB Jig doesn't work either, then your last option is to consult the Service Center. Do post the result. Hope I Helped
elisterr said:
The only sign of life - whatever I do it has black screen with backlight on but nothing else.
What can I do? They say that a broken phone is only with hardware problems but could I have f**** up the software so much that its the same?
Click to expand...
Click to collapse
1. make sure you have installed drivers on your computer
2. remove battery > connect phone to computer > press volume buttons and lock key
3. if you get a black screen just press the volume up button.
odin will recognize the device
if this does not work then try multi-formatter
using it, format rfs partition and then install some custom rom.
link to multi-formatter thread : click here
mahithm said:
You can try this guide by @SuperMini to force open Download Mode from odin. Here is the link,
How to unbrick Samsung Galaxy Ace
Make sure to use the key combination of Download Mode for your device as the one mentioned in the guide is for Samsung Galaxy Ace S5830. If that doesn't work, then you can try the USB Jig (not always guaranteed to work). If USB Jig did work, then it will force open the Download Mode so you can flash stock rom back using odin. If USB Jig doesn't work either, then your last option is to consult the Service Center. Do post the result. Hope I Helped
Click to expand...
Click to collapse
Well. Bought one from ebay. It finally arrived. Hoping for a miracle.
I connected it and.... Nothing. Absolutely nothing.
elisterr said:
Well. Bought one from ebay. It finally arrived. Hoping for a miracle.
I connected it and.... Nothing. Absolutely nothing.
Click to expand...
Click to collapse
Go to service center and tell them to flash mobile
Sent from my GT-S5830i using Tapatalk 2
elisterr said:
Well. Bought one from ebay. It finally arrived. Hoping for a miracle.
I connected it and.... Nothing. Absolutely nothing.
Click to expand...
Click to collapse
I'm sorry to hear that. Now as the last resort, you can consult the Service Centre.
Hey guys i got a slight problem.
I had the Android Revolution HD Rom and i was trying to install another one , it really wasnt my first time doing this however this time a problem occurred.
My volume side buttons are not working so i couldnt get into recovery mode using them also on top of that the rom itself didnt have the option to go to recovery when turning off the phone.
I downloaded the Quick boot tool apk from Playstore and used it to go to recovery... I WISH I DIDNT
now my phone when turned on shows samsung logo and it goes to recovery and quickly goes back to the logo and loops in that way...
Is there anyway to access the download mode without pressing them sidebuttons, i even tried ODIN but it cant recognize the phone because it keeps looping...
I am clueless now and any help would be appreciated.
Sorry for spelling or any typos i am really angry atm.
alioni said:
Hey guys i got a slight problem.
I had the Android Revolution HD Rom and i was trying to install another one , it really wasnt my first time doing this however this time a problem occurred.
My volume side buttons are not working so i couldnt get into recovery mode using them also on top of that the rom itself didnt have the option to go to recovery when turning off the phone.
I downloaded the Quick boot tool apk from Playstore and used it to go to recovery... I WISH I DIDNT
now my phone when turned on shows samsung logo and it goes to recovery and quickly goes back to the logo and loops in that way...
Is there anyway to access the download mode without pressing them sidebuttons, i even tried ODIN but it cant recognize the phone because it keeps looping...
I am clueless now and any help would be appreciated.
Sorry for spelling or any typos i am really angry atm.
Click to expand...
Click to collapse
You can use Android Debug Bridge (ADB) to enter whether download mode or recovery.
josephiskandar said:
You can use (ADB) to enter whether download mode or recovery.
Click to expand...
Click to collapse
I will try this and get back to you.
Thanks
josephiskandar said:
You can useAndroid Debug Bridge (ADB) to enter whether download mode or recovery.
Click to expand...
Click to collapse
Did everything and it still does the same loop, from logo to partially loaded recovery and back...
alioni said:
Did everything and it still does the same loop, from logo to partially loaded recovery and back...
Click to expand...
Click to collapse
It doesn’t sound good then. Please read again threads like this on how to recover from a bootloop. If you really can’t access neither recovery or download mode using adb, that’s out of my knowledge, and you might need to read about how to fix a hard brick. There’s a thread about that in these stickies.
josephiskandar said:
It doesn’t sound good then. Please read again threads like this on how to recover from a bootloop. If you really can’t access neither recovery or download mode using adb, that’s out of my knowledge, and you might need to read about how to fix a hard brick. There’s a thread about that in these stickies.
Click to expand...
Click to collapse
i managed to get into download mode however prior the brick i didnt enable developer mode on the phone and now the pc cannot recognize it when connected.
Developer switch is irrelevant to download mode, search the many threads on things to try to get Odin connected.