My phone will no longer start up, it stays black, no loading whatsoever. I can no longer access my recover mode, but can still get to my download mode. No matter what I do, I can't load a stock ROM back on the phone.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have searched threads for things I can do, and have come up empty. I don't know what I should be focusing on first to get my phone back to an operable state.
My PPA is I9100MUGMA5
this is the rom I tried to put back I9100MUGMA5_I9100OYCMA5_I9100MUGMA5_HOME.tar.md5
I am at a complete dead end, if someone has any suggestions please help
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PhilZ-cwm6-XXLSJ-OXX-3.5.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> zImage
I have since tried using the pit file and installing Philz, but it seems to be just hanging at the zImage.
funkdrshads said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PhilZ-cwm6-XXLSJ-OXX-3.5.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> zImage
I have since tried using the pit file and installing Philz, but it seems to be just hanging at the zImage.
Click to expand...
Click to collapse
Let try to run your Odin as Adminstrator if you use Win 7 or Win 8
Hoper8's 'Odin troubleshooting' thread. Search for it, try the stuff in the thread.
Related
i was trying to install jellyblast in my phone. the rom got installed. but when i tried restarting the phone, it got ricked.
i am trying to use odin but it comes as
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLD3_S5830iODDLD2_RST_S5830iDDLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl.bin
<ID:0/003> BcmCP.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i dont know what to do. please help
First of all Wrong Section.I understand you are new,but post in the appropriate section.
Try using Odin v3.07 or refer this guide http://forum.xda-developers.com/showthread.php?t=1840645
Sent from my GT-S5830i using xda app-developers app
Searched and have tried to fix my issue on here for 2 days now reaching out for help. Rooted my verizon Note 3 SM-N009 running 4.4.2 with safestap and tried to flash a rom from this post http://forum.xda-developers.com/showthread.php?t=2726558. Completly new to rooting and everything. I have downloaded oden 3.07 and 3.09 and get the same problem
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-hltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a nandroid backup to my stock root on my internal sd card. Someone lend me a hand
Mot sure what specs i need to list here. i have the sch-i545, 4.3 and MJ7.
Im trying to use odin to flash stock but i keep getting this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I tried another .tar and im now getting the firmware upgrade encountered an issue. please select recovery in kies & try again.
I am completely lost and activating my old droidx till this can be fixed.
Denots said:
Mot sure what specs i need to list here. i have the sch-i545, 4.3 and MJ7.
Im trying to use odin to flash stock but i keep getting this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I tried another .tar and im now getting the firmware upgrade encountered an issue. please select recovery in kies & try again.
I am completely lost and activating my old droidx till this can be fixed.
Click to expand...
Click to collapse
You're using an MDK Odin tar...you need to use an MJ7 Odin tar instead.
Sent from my SCH-I545 using XDA Premium 4 mobile app
I found this file
N900VVRUBMJ7_N900VVZWMJ7_N900VVRUBMJ7_HOME.tar.md5
looks like same error in odin
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUBMJ7_N900VVZWMJ7_N900VVRUBMJ7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
So where do i go from here?
Denots said:
I found this file
N900VVRUBMJ7_N900VVZWMJ7_N900VVRUBMJ7_HOME.tar.md5
looks like same error in odin
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUBMJ7_N900VVZWMJ7_N900VVRUBMJ7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
So where do i go from here?
Click to expand...
Click to collapse
Thats for the note 3. Here download this
I tried odin a few times on all of the tar's i have and continued to get the "succeed0/fail1" error but now i can boot up the phone to how i was before the "firmware upgrade error"
Waiting for the file you linked to finish downloading then giving it a try.
UPDATE
The file you linked worked, back on stock now time to get to rooting.
Denots said:
I tried odin a few times on all of the tar's i have and continued to get the "succeed0/fail1" error but now i can boot up the phone to how i was before the "firmware upgrade error"
Waiting for the file you linked to finish downloading then giving it a try.
UPDATE
The file you linked worked, back on stock now time to get to rooting.
Click to expand...
Click to collapse
You're welcome.
Sent from my SCH-I545 using XDA Premium 4 mobile app
Hey all,
My sch-i545 is stuck in download mode, cannot boot. I want to delete everything and start over.
I downloaded the stock 5.0.1 rom, which what i believe was on it before it soft bricked, and every time I try to run odin with the md5 the program becomes unresponsive. Any ideas???
Download this one. It's official stock:
ODIN v3.10:
https://drive.google.com/file/d/0B4RU_ZH5QUASNmxLX3JpejBXREE/view?usp=docslist_api
OC1 image:
https://drive.google.com/file/d/0B4RU_ZH5QUASaU9LcDJ3WWZfdXM/view?usp=docslist_api
Sent from my SCH-I545 using Tapatalk
Thank you for the file. so this time it does not crash odin, but now it says complete write operation failed.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_I545VRUGOC1_I545VZWGOC1_CL4584173_QB4517016_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Try to use 3.09. It's the only one that worked for me.
Odin 3.0.9 seems to work better, but it fails at a certain point per below.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_I545VRUGOC1_I545VZWGOC1_CL4584173_QB4517016_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Any thoughts? :-\
You'll want to flash the first link in this one:
http://forum.xda-developers.com/gal...pment/odin-i545vrugoc1-factory-image-t3160125
What you are trying to flash is a ROM someone put together I believe. It's not the exact factory image and is probably not wiping all the bad files.
Thank you for the help so far, but I still have the same problem with writing. It fails after about 7 minutes.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I545VRUGOC1_I545VZWGOC1_I545VRUGOC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Any ideas? :-\
Download the PIT file and flash that along with the ROM
Sent from my draconis using Tapatalk
I have a pit file from December 2013, the only one I could find. Still have no luck getting it to flash when using that PIT
Any ideas?
Nanometer45 said:
Any ideas?
Click to expand...
Click to collapse
Are you using the stock USB cable you know the Samsung one?
I tried 3 different cables. the one that worked? The USB cable I just got for my S6. Thanks for your help!
So I go to flash twrp with Odin and then after SetupConnection it throws an error. Logs are here:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 9 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
.