Wireless Charging W/ Lifeproof case ..help needed - Verizon Samsung Galaxy S 4

Hello everyone I wanted to share my experience with a wireless charging pad and a lifeproof case. I purchased the Nuud lifeproof case a while back and ended up having to replace it due to the charging door that snaps closed started breaking. I figured a way to prevent me from opening that little snap door is to go with wireless charging.
I purchased the wireless charging reciever card and the oem charging pad off amazon. Much to my disappoint me the case was too thick for the wireless charge to continually work. It recognizes that its on the pad but would act as if I were plugging and unplugging a power cord every 2 seconds. So I tried to come up with ways to reduce the surface area between my card and the charger pad. I removed the stickers which ended up not being enough but then came up with the idea to remove the top cover of the oem charging pad. Removing this plastic seems like it was just enough to get it to work correctly. The only problem I see now is the phone is actually sitting on top of the coil which brings up some heat issues.
I'm thinking of sewing together some fabric to act as a cover. What do you guys think about this?

BUMP - I have a very thick ballistics case. I am wondering if a solution like this would work for me as well.

stein5830 said:
BUMP - I have a very thick ballistics case. I am wondering if a solution like this would work for me as well.
Click to expand...
Click to collapse
I doubt my case is as thick as yours stein but it is working correctly once I removed the plastic cover on the charger pad. Not sure if you have all the items yet but you can find them on amazon for probably around 60 bucks.

Wireless Charging is working fine for me with my Otterbox Defender case and an Incipio Ghost 100 Wireless Charging Base. I'm using a cheap China QI antenna receiver that I got on eBay.
Currupt247 said:
Hello everyone I wanted to share my experience with a wireless charging pad and a lifeproof case. I purchased the Nuud lifeproof case a while back and ended up having to replace it due to the charging door that snaps closed started breaking. I figured a way to prevent me from opening that little snap door is to go with wireless charging.
I purchased the wireless charging reciever card and the oem charging pad off amazon. Much to my disappoint me the case was too thick for the wireless charge to continually work. It recognizes that its on the pad but would act as if I were plugging and unplugging a power cord every 2 seconds. So I tried to come up with ways to reduce the surface area between my card and the charger pad. I removed the stickers which ended up not being enough but then came up with the idea to remove the top cover of the oem charging pad. Removing this plastic seems like it was just enough to get it to work correctly. The only problem I see now is the phone is actually sitting on top of the coil which brings up some heat issues.
I'm thinking of sewing together some fabric to act as a cover. What do you guys think about this?
Click to expand...
Click to collapse

Try moving the phone slightly on the charging pad.
I don't have the factory pad but on both of my qui charging pads the phone needs to be placed slightly above center. If I put it directly on the center I experienced the same symptoms you are describing.
Sent from a Galaxy S4... Far far away

gadget! said:
Try moving the phone slightly on the charging pad.
I don't have the factory pad but on both of my qui charging pads the phone needs to be placed slightly above center. If I put it directly on the center I experienced the same symptoms you are describing.
Sent from a Galaxy S4... Far far away
Click to expand...
Click to collapse
im thinking this oem charging pad is the prob I'm going to order the ghost and see if I get better results.

Related

[Review] Generic Ebay desktop Charging dock + battery dock, sort of work w/ TPU case

Got my order from HK
This is exact item that I got
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=230644510493
Overall I just wanted a charging dock for my night stand, this does the job.
Some items of notes
1) It does fit a TPU case, but the charging tip is sort of in between the correct length for TPU case or no case. a bit too long for no case, can see a gap between base and phone, a bit not quite long enough for TPU case, with case on have to make sure to press down firmly and to double check the phone is actually charging, any thicker than the one I got and may not be able to charge. edit: This is mainly due to the locking spring on the charging tip, being not quite 100% inserted, the spring is pushing the phone up and out of the tip instead of locking the phone in, You can make it charge more reliably by bending down or removing the locking springs on the charging tip.
---
Also, with no case the back as seen from the pictures have a gap, so the phone is basically standing up supported by the charge port. I don't think this is a good idea long term as it put stress on the charge port. edit: However after sleeping on it, it dawn to me that you can easily mod the dock by adding some foam padding to give it a more snug fit and better support.
2) left and right side don't have rounded guide/support like the iGrip car dock that allow you to slide the phone in easily, you have to be careful lining up the charging tip and the charge port yourself.
3) To charge the phone, the attached USB A cable end must be either connect to a charger or a computer.
To charge the battery the mini USB port on the back of the dock need to be connect to a charger (provided) or a PC.
This took me a while to figure out why my phone won't charge with the charger plugged into the mini USB port.
4) pulled the sticker on the Galilio 2000mah battery, just like another forum poster confirmed that underneath the sticker, its got 1000mah marked on the metal housing of the battery itself
5) There's a version of this dock without the battery charger, its also a little bit cheaper
6) It does not activate dock mode
Nice, thanks for posting pics. I ordered the dock with 2of the Galilio batteries. Sucks they are only 1000mah, but I guess it will do as a backup in a crunch...
Sent from my PG86100 using XDA Premium App
Do you see this working with a Commuter Case by chance?
I don't have a commuter case, so can't confirm one way or another, i can only say if the case is similar thickness is TPU case, it should work, if its thicker than TPU cases, it probably either won't fit the back (back is about 1mm clearance with TPU case, but can tilt/lean so it touch the dock for support), or the charging tip won't be long enough if the side is too thick. Judging from the otterbox picture of the commuter case, I "think" it should fit as it seem similar thickness to TPU
Bah. Too bad it doesn't activate dock mode.
Sent from my PG86100 using XDA App
sparhawk6 said:
Bah. Too bad it doesn't activate dock mode.
Sent from my PG86100 using XDA App
Click to expand...
Click to collapse
I'm doing some research on this issue, its either a magnet or adding a resistor to certain pins in the charging tip to activate dock mode. not quite sure which yet for our phone

Adding wireless charging & magnets?

The Nexus 5/7 has Qi charging built-in and will stick to the magnetic Nexus Wireless Charging Pad.
I have seen this for the Note 3 that will add Wireless charging: http://www.amazon.com/dp/B00GMRXD9U/
and this magnetic car dock that comes with a metal plate: http://www.amazon.com/dp/B00DPMNNUO/
Is it possible to add both to the Note 3 without changing to a thicker battery cover?
I would like to know also. Can anyone advise? Thanks in advance..
I just spoke to another user via PM.
Apparently the nGroove Snap holds the phone pretty well using just the official Samsung Wireless Charging Cover, without an additional metal plate. Looking at pics online, i can see that there's some more metal in that cover, maybe that's why it works.
I had also read about people putting the metal plate behind their batteries - but I have no idea how thick it actually is.
The second one is good.
anyone knows of a similar pass through coil in Uk, i mean ebay UK or amazon.

The Air Dock: What works with it for you?

Hey everyone,
Just received my Air Dock in the mail and I've had mixed results using my Galaxy Note 3 with it. So rather than buying more cases and QI adapters, throwing stuff at the wall hoping something sticks, I thought we could all band together to find the best setup. This should be a thread for people to post their experiences and post links to the cases and wireless charging adapters they are using with the Air Dock and their GN3.
For those of you unfamiliar with the Air Dock, it's a new Indiegogo backed vehicle mount that employs nano-suction and QI wireless charging. It essentially uses a bunch of tiny suction cups (and some magnets apparently) to bond to your phone with out needing any kinds of harnesses or clips. The only issue seems to be that this tech requires some specific stuff to function well. The back of the phone needs to be high gloss plastic for it to stick well and it can't be too thick (i think .8mm is the max for it to still charge). For phones with matte backs (like the Nexus 5) magnets are an option.
Here is the link to the website and plenty of videos and pictures for those who don't know about it: TheAirDock.com
Ok, so I'll start with my setup and experience and hopefully others will follow along to find the best combination of accessories to get the most out of this dock.
Phone: Black Galaxy Note 3 (Verizon)
-I tried it on the dock with no case and while it holds, I'm not very confident in it. I think it may be the texture of the soft touch back. Also there seems to be magnets in it, which I'm not sure there were supposed to be but they are responding to something in the phone
Case: Black Cruzerlite Hybrid Case for Samsung Galaxy Note 3
-Same deal, it sticks to it but it's not inspiring confidence. It's not a high gloss back, so that's probably the issue (bought it well before the Air Dock). The dock also comes with a magnet sticker to place between the case and phone, and that helps but I haven't been able to get it to register a charge at all with the case on.
QI adapter: Wireless Qi Power Receiver Car Charger NFC For Samsung Note 3 N9000 N9005 BC279
-I think this is the part that has created the biggest issue. It's only ever recognized the charger a handful of times, with and without the back cover on. And even when it recognizes it, it just flashes the "now wireless charging" dealy and then goes back to discharging immediately. I know that the adapter works because it charges fine on my desktop QI charging pad.
It holds GN3 securely?
Jc003125 said:
It holds GN3 securely?
Click to expand...
Click to collapse
Not exactly. If i put it on there with no case and like 15 degrees of back lean it holds decently. The backplate isn't as glossy as it needs to be to hold securely though. It's capable of it, they've shown it holding the various Nexus tablets.
That's kind of what this thread is about, trying to find out the best combination of accessories to make this thing work correctly.
Sent from my Galaxy Note 3 via Tapatalk
i'm still waiting on my airdock, but regarding the QI receiver insert charging/discharging deal, have you tried to rotate the airdock 90 degrees? I've ran across QI chargers where orientation matters.
oilfighter said:
i'm still waiting on my airdock, but regarding the QI receiver insert charging/discharging deal, have you tried to rotate the airdock 90 degrees? I've ran across QI chargers where orientation matters.
Click to expand...
Click to collapse
Hmm. I think that's worth a shot. The dock is weird in that the ball joint faces a specific direction, which is different than the prototypes I saw. And if what you say is true, mounting it on the windshield would make the dock upside down. I'll give that a go when I go to my car in the AM.
Sent from my Galaxy Note 3 via Tapatalk
B1gC72 said:
Hmm. I think that's worth a shot. The dock is weird in that the ball joint faces a specific direction, which is different than the prototypes I saw. And if what you say is true, mounting it on the windshield would make the dock upside down. I'll give that a go when I go to my car in the AM.
Sent from my Galaxy Note 3 via Tapatalk
Click to expand...
Click to collapse
an easier way is to not move the dock, and just rotate your phone 90 degrees (vertical vs. horizontal), and see if that helps with the wireless charging.
B1gC72 said:
Hey everyone,
Just received my Air Dock in the mail and I've had mixed results using my Galaxy Note 3 with it. So rather than buying more cases and QI adapters, throwing stuff at the wall hoping something sticks, I thought we could all band together to find the best setup. This should be a thread for people to post their experiences and post links to the cases and wireless charging adapters they are using with the Air Dock and their GN3.
For those of you unfamiliar with the Air Dock, it's a new Indiegogo backed vehicle mount that employs nano-suction and QI wireless charging. It essentially uses a bunch of tiny suction cups (and some magnets apparently) to bond to your phone with out needing any kinds of harnesses or clips. The only issue seems to be that this tech requires some specific stuff to function well. The back of the phone needs to be high gloss plastic for it to stick well and it can't be too thick (i think .8mm is the max for it to still charge). For phones with matte backs (like the Nexus 5) magnets are an option.
Here is the link to the website and plenty of videos and pictures for those who don't know about it: TheAirDock.com
Ok, so I'll start with my setup and experience and hopefully others will follow along to find the best combination of accessories to get the most out of this dock.
Phone: Black Galaxy Note 3 (Verizon)
-I tried it on the dock with no case and while it holds, I'm not very confident in it. I think it may be the texture of the soft touch back. Also there seems to be magnets in it, which I'm not sure there were supposed to be but they are responding to something in the phone
Case: Black Cruzerlite Hybrid Case for Samsung Galaxy Note 3
-Same deal, it sticks to it but it's not inspiring confidence. It's not a high gloss back, so that's probably the issue (bought it well before the Air Dock). The dock also comes with a magnet sticker to place between the case and phone, and that helps but I haven't been able to get it to register a charge at all with the case on.
QI adapter: Wireless Qi Power Receiver Car Charger NFC For Samsung Note 3 N9000 N9005 BC279
-I think this is the part that has created the biggest issue. It's only ever recognized the charger a handful of times, with and without the back cover on. And even when it recognizes it, it just flashes the "now wireless charging" dealy and then goes back to discharging immediately. I know that the adapter works because it charges fine on my desktop QI charging pad.
Click to expand...
Click to collapse
The receiver you have is not a very good one, its rather weak, i had to add another ferrite or flexi magnet to it so that most of my other transmitter can detect it, but if nfc is a must, you have no choice.
oilfighter said:
an easier way is to not move the dock, and just rotate your phone 90 degrees (vertical vs. horizontal), and see if that helps with the wireless charging.
Click to expand...
Click to collapse
So I tried all orientations and no such luck. I think it's the QI adapter.
Sent from my Galaxy Note 3 via Tapatalk
kms108 said:
The receiver you have is not a very good one, its rather weak, i had to add another ferrite or flexi magnet to it so that most of my other transmitter can detect it, but if nfc is a must, you have no choice.
Click to expand...
Click to collapse
Good to know. NFC isn't a must so could you recommend a better QI adapter for the thread?
Sent from my Galaxy Note 3 via Tapatalk
Would also like to report back on the docks performance today. I had my phone on it (in the case) all day with just a small amount of back lean. It held strong on the drive to and from bwork. I also went for some drinks after work and it held strong to and from along a fairly bumpy road. I still want to find a glossy back case but my confidence is growing in the nano suction as is.
I also wanted to report that I put my old Galaxy S1 in it (only phone I have with a glossy back) and it held just like it does in the videos.
Sent from my Galaxy Note 3 via Tapatalk
B1gC72 said:
Good to know. NFC isn't a must so could you recommend a better QI adapter for the thread?
Sent from my Galaxy Note 3 via Tapatalk
Click to expand...
Click to collapse
There is three
nillkin has one with qi/ s view function
http://forum.xda-developers.com/showthread.php?t=2605204
yijieneng
powerqi with copper coil (non nfc)
yijieneng and powerqi shown below.
Hi Guys,
Just to know if I'm the only one experiencing difficulties with my airdock :
I received my items 2 days ago (I have 2 as a friend also ordered one) and test them with 2 Nexus 4 :
Concerning the suction, it's definitily very very good with the N4 and no case, clearly, no risk to have the phone fall while driving !
So, that was the good news ...
The bad one is that the charging is very unreliable on both airdock pads, but with differents effects :
On the first one, it's very difficult for it to be seen charging by the phone, but when it does, it work for several minutes ... and stop working without apparent reasons ...
On the second one, I experiment the same kind of symptoms as described in the first post : the wireless charging is only seen by the phone for something like 1/2s, and then it's off ...
That's quite a disppointment as otherwise, it holds the phone just fine in the car and I found it very convenient. I hope I was just unlucky with mines, or maybe they suffer from transport (the package shows no evidence of it yet ...).
I contacted Greg, the guy from theAirdock.com to have his advices on the matter, but no answer so far ... I was wondering if I'm the only experimenting those issues ?
rogue931 said:
Hi Guys,
Just to know if I'm the only one experiencing difficulties with my airdock :
I received my items 2 days ago (I have 2 as a friend also ordered one) and test them with 2 Nexus 4 :
Concerning the suction, it's definitily very very good with the N4 and no case, clearly, no risk to have the phone fall while driving !
So, that was the good news ...
The bad one is that the charging is very unreliable on both airdock pads, but with differents effects :
On the first one, it's very difficult for it to be seen charging by the phone, but when it does, it work for several minutes ... and stop working without apparent reasons ...
On the second one, I experiment the same kind of symptoms as described in the first post : the wireless charging is only seen by the phone for something like 1/2s, and then it's off ...
That's quite a disppointment as otherwise, it holds the phone just fine in the car and I found it very convenient. I hope I was just unlucky with mines, or maybe they suffer from transport (the package shows no evidence of it yet ...).
I contacted Greg, the guy from theAirdock.com to have his advices on the matter, but no answer so far ... I was wondering if I'm the only experimenting those issues ?
Click to expand...
Click to collapse
You're not the only one, I had similar issues with my Note 3 (actually why I started this thread). I ended up contacting Greg as well and he recommended I purchase a Qi adapter from their site, which did make it function much more reliably. It's acceptable in my opinion at this point but I'm still not 100% sure it's going to charge or stay charging anytime I set it on the AirDock.
Bad news is, my solution isn't really an option with the N4 since (i believe) the wireless charging is built in. I do believe that the Qi charger in the AirDock is generally weak though since I tried about 3 different Qi adapters before finally buying the one from the AirDock site that worked. Otherwise it would do exactly what yours is doing (got both of the things you described with different adapters). I would say try to exchange your docks.
Something that works for me sometimes if it doesn't start charging right away is to unplug the USB cable from the lighter socket side and plug it back in. Also be sure that you are plugged into the 2.1A socket that it comes with, as i found it won't work with the standard 1A plugs most people have laying around.
I really love the concept of the AirDock and I'm glad I backed it but the build quality is certainly suspect. Mine is starting to fall apart after only a few months (the suction pad part is starting to separate from the housing, i can only assume because of how the phone has to be pulled to remove). I think this is par for the course with beta hardware though. Fortunately, customer service was very accommodating in my experience. Hope you're as fortunate.
Yep, actually, I found the thread on the N5 forum after I put my post here. And there indeed seems to be a few complaints with it
I had ne feedback from Greg sincemy email yesterday, but I figure they may be quite busy those days as many people seems to be receiving them.
Well, I hope he will provide a solution, because, for one of the two, with the same symptoms as yours, I can believe it's a problem with positionning, but for the other, the phone start charging for a few minutes and, without it moving, stops ... To me it sounds more like a loose contact somewhere inside the airdock ...
Well, wait'n see, they say ...
I will keep you posted of Greg's answer ..
Any word on how this works with the Note 3's stock "leather" textured back? Is a case required for it to stay?
Also, has anybody tried it with the Samsung brand wireless charger cover? The Air Dock website suggests that the Samsung brand cover is the best wireless charger receiver available; even better than the ones that Air Dock sells.
do you use the Magnetic Sticker?
For the original poster, how did things work out for you in the end? I have a Nexus 5 and it works extremely well with the AirDock because of the smooth back and also because of the magnets. I'm thinking of going to the Note 4. On the AirDock site it does say the textured back of the Note may not stick too well so they recommend using the magnetic sticker. I have one that come with my AirDock and can't imagine putting that on the back of the phone case. I expect it would be pretty damn ugly.
2xbass said:
For the original poster, how did things work out for you in the end? I have a Nexus 5 and it works extremely well with the AirDock because of the smooth back and also because of the magnets. I'm thinking of going to the Note 4. On the AirDock site it does say the textured back of the Note may not stick too well so they recommend using the magnetic sticker. I have one that come with my AirDock and can't imagine putting that on the back of the phone case. I expect it would be pretty damn ugly.
Click to expand...
Click to collapse
I thought for sure I had already posted this response. I ended up getting an AirDock and the OEM Samsung Wireless charging cover for my Note 3. It's been a good setup. I'm not using the ugly sticker. The magnets in the AirDock seem to hold on to some metal in the wireless cover. It isn't as good as a smooth backed device, but it works for the most part. I'm glad I bought it.
That's good to know. Thanks for replying. One way to get a smoother back and increase the adhesion on the AirDock while avoiding the thickness of a case is to get a vinyl wrap although I'm not sure how they would go with the Samsung wireless back since it looks like the shape especially around the camera is slightly different. I have a D-Brand skin on my Nexus 5 and I really love it and it makes the back even smoother. I just got a Note 4 yesterday and have ordered a third-party Qi receiver coil so I'll see how that goes first. Looks like SlickWraps has some nice vinyl skins for the Note 3 and 4.
Also want to report that yesterday I tried my Note 4 with the AirDock using the standard back. At first it did not adhere at all. However I noticed that surface of my AirDock charging pad was pretty dusty. For my Nexus 5 I had been relying mostly on the magnets to hold the phone there. So I cleaned the AirDock with a bit of water as they recommend and the Note 4 holds very securely now. I think if I add a vinyl skin or a very thin case I think it would be even more secure.

Car mount with wireless charging.

Looking for a good car mount with wireless charging that will work with the nexus 6 any recommendations?
I'd recommend not using one. Wireless charging will be way to slow on the n6.
jdenman03 said:
I'd recommend not using one. Wireless charging will be way to slow on the n6.
Click to expand...
Click to collapse
used the square stock wireless charger with my n5, stuck a clip to the back of it and just relied on the magnets to hold it. Didn't wiggle at all, never fell off, was perfect, wish I could rig the same thing with the N6, but I don't think the magnets will be near strong enough.
A qi charge is going to charge at 1a at most, for he N5 that was more than enough to cover full brightness, gps, and streaming over bluetooth, and still providing enough to charge the battery. I IMAGINE if you could somehow hook it up like that, it would provide enough of a charge to the N6 as well, at worst I think you'd not lose charge. JMHO though.
So if you not recommending the wireless charge on it then do the sell a fast charge adapter for the car? Really the main thing is a good car dock. I figured the wireless charge would just be a plus.
I've been using the Airdock with my Nexus 5 for a while now and I absolute LOVE it. It uses magnets to hold the N5 in place, and I'm hoping the N6 also has these magnets. It also has a special surface that is supposed to hold certain phones without magnets, depending on the material of the back of the phone.
Also as far as the speed of charging, it works well enough to slowly charge my N5 with the screen always on in my car and with GPS running (at a minimum, it keeps it from losing charge). This is all I need in my car. On those certain occasions where you really want a faster charge, I just plug it in.
Let us know if it works with N6. Can you have a slim case on the phone an the magnet still works?
Got my N6 today. Unfortunately it doesn't work with the AirDock, as it doesn't stay on it. Looks like the N6 doesn't have any magnets. Very disappointing.
nyijedi said:
Got my N6 today. Unfortunately it doesn't work with the AirDock, as it doesn't stay on it. Looks like the N6 doesn't have any magnets. Very disappointing.
Click to expand...
Click to collapse
I've read the magnets are near the bottom of the phone. Can you double check?
fictionoid said:
I've read the magnets are near the bottom of the phone. Can you double check?
Click to expand...
Click to collapse
I just ran a magnet all over the back of the N6. There is indeed some type of magnetic pull in the bottom corner, however, it is EXTREMELY weak. I'm guessing it's there to maybe help nudge the phone into the correct position when laying flat on a (future official?) qi charger, but it is absolutely not enough to hold it onto the AirDock. By way of comparison, the magnetic pull with the magnet is much stronger, and over a much greater area, on the N5.
Also, the N6 is a lot heavier than the N5. Add the curved back into the equation, and these 3 factors pretty much guarantee the phone won't work with the AirDock. Believe me, I tried to get it to stick on the AirDock today, and there's no way it's happening.
iOttie Qi charger works. You've got to find the sweet spot to have it grasp the side, without hitting the volume buttons, and still getting the charging coils aligned. Not super difficult - just takes a second to align. I expect this to be irrelevant once I get a case which keeps the buttons recessed.
-bZj
Anyone who's using a QI car dock have any input on charging / maintaining charge with screen always on, brightness up, streaming music, maps, etc.
I'm just curious if the iOttie or any other wireless chargers can avoid LOSING charge with the N6 when under "heavy" use.
One problem I find is you can't keep the screen on when wirelessly charging once the battery is at 100%. The phone stops charging so the screen goes off. Very annoying hopefully someone can find a fix.
MoeDaddy said:
One problem I find is you can't keep the screen on when wirelessly charging once the battery is at 100%. The phone stops charging so the screen goes off. Very annoying hopefully someone can find a fix.
Click to expand...
Click to collapse
The "Stay Awake" option in the Developer Options should be what you're looking for.
No that doesn't work when the phone is fully charged because the N6 doesn't have trickle mode it actually shuts off charging. Thus the screen shuts off.
My Homebrew Wireless Car Charging Solution
I made my own wireless car charger by grafting a PowerBot charging puck onto a Ram Large X-Grip. I simply used double-faced tape to attach the PowerBot to the X-Grip. I started this with my Nexus 5 in a Spigen Neo-Hybrid case and it works just as well with my N6 inside a Diztronic Slim TPU case.
Here's the charger:
http://www.amazon.com/PowerBot®-PB1...687&sr=8-1&keywords=powerbot+wireless+charger
And here's the X-Grip:
http://www.amazon.com/Ram-Mount-Uni...TF8&qid=1416714725&sr=8-4&keywords=ram+x-grip
You'll need a way to attach the X-Grip to your vehicle. Ram-Mount's website has countless ways to do this.
Here's Ram's website:
http://www.rammount.com/
I used a Mirror-Mate(TM):
http://www.rammount.com/NewProducts/MirrorMount/tabid/2538/Default.aspx
And paired it with a Long Arm (don't use the shorter ones; the phone will hit the rear-view mirror in portrait orientation):
http://www.rammount.com/CatalogResu...65077045066045050048049085045067/Default.aspx
I can leave the PowerBot plugged into my cigarette lighter all the time (standard mini-USB cable and 12V-USB adapter) and it's easy to mount or remove the phone, just squeeze the arms of the X-Grip together and out it comes (this takes two hands or the phone will fall). This works great for calls, navigation, or as a dash-cam. Ram makes suction cups for those who want to mount directly to the windshield but I highly recommend the Mirror-Mate(TM).
Not cheap, total cost about $70 plus shipping.
EDIT: I just saw this in another thread and I'm going to replace my PowerBot with this Anker:
http://www.amazon.com/Anker-Ultra-S...Qi-Enabled/dp/B00HIZ3ZI4/ref=cm_cd_ql_qh_dp_t
Right now the 4 rubber grippers are flush with the front of the phone, which makes it a bit finicky to mount securely. The Anker charging pad is about 1/8" thinner than the PowerBot, which will accommodate the thickness of the phone perfectly with about 1/8" of overlap between the 4 grippers and the bezel of the N6. Putting the N6 in the X-Grip without the charger in-between leaves the 4 grippers protruding above the bezel about 3/8" which means they can get in the way if I'm trying to use the touchscreen near them.
See my posts in this thread...
http://forum.xda-developers.com/showthread.php?t=2910978
[Q] Car mount similar to iOttie?
Sent from my Nexus 6 using Tapatalk
toyfreak said:
I made my own wireless car charger by grafting a PowerBot charging puck onto a Ram Large X-Grip. I simply used double-faced tape to attach the PowerBot to the X-Grip. I started this with my Nexus 5 in a Spigen Neo-Hybrid case and it works just as well with my N6 inside a Diztronic Slim TPU case.
Here's the charger:
http://www.amazon.com/PowerBot®-PB1...687&sr=8-1&keywords=powerbot+wireless+charger
And here's the X-Grip:
http://www.amazon.com/Ram-Mount-Uni...TF8&qid=1416714725&sr=8-4&keywords=ram+x-grip
You'll need a way to attach the X-Grip to your vehicle. Ram-Mount's website has countless ways to do this.
Here's Ram's website:
http://www.rammount.com/
I used a Mirror-Mate(TM):
http://www.rammount.com/NewProducts/MirrorMount/tabid/2538/Default.aspx
And paired it with a Long Arm (don't use the shorter ones; the phone will hit the rear-view mirror in portrait orientation):
http://www.rammount.com/CatalogResu...65077045066045050048049085045067/Default.aspx
I can leave the PowerBot plugged into my cigarette lighter all the time (standard mini-USB cable and 12V-USB adapter) and it's easy to mount or remove the phone, just squeeze the arms of the X-Grip together and out it comes (this takes two hands or the phone will fall). This works great for calls, navigation, or as a dash-cam. Ram makes suction cups for those who want to mount directly to the windshield but I highly recommend the Mirror-Mate(TM).
Not cheap, total cost about $70 plus shipping.
EDIT: I just saw this in another thread and I'm going to replace my PowerBot with this Anker:
http://www.amazon.com/Anker-Ultra-S...Qi-Enabled/dp/B00HIZ3ZI4/ref=cm_cd_ql_qh_dp_t
Right now the 4 rubber grippers are flush with the front of the phone, which makes it a bit finicky to mount securely. The Anker charging pad is about 1/8" thinner than the PowerBot, which will accommodate the thickness of the phone perfectly with about 1/8" of overlap between the 4 grippers and the bezel of the N6. Putting the N6 in the X-Grip without the charger in-between leaves the 4 grippers protruding above the bezel about 3/8" which means they can get in the way if I'm trying to use the touchscreen near them.
Click to expand...
Click to collapse
Did you use super glue or something to attach the Qi charger to the Xgrip?
Also, how long is the USB cable provided by Anker?
picked this up on sale for my nexus 6 w/ spigen ultra hybrid
https://slickdeals.net/f/7565384-au...s-smartphone-charger-qi-for-9-99-frys-com?v=1
nexus 6 is a bit wide for it, but the handles flex enough to let it go in; wireless charging, went up 1% from ride home from frys with gps navigation on w/ screen halfway
Momotani-Hitoshi said:
Did you use super glue or something to attach the Qi charger to the Xgrip?
Also, how long is the USB cable provided by Anker?
Click to expand...
Click to collapse
I used double-faced mounting tape between the X-Grip and charger. The cable is 1m long.
What did you use to bond the qi charger to the ram mount?

[MOD] Cheap wireless charging (~$15USD)

I wanted wireless charging, but the only one available (from fonesalesman.com) costs about $80USD to my door.
So, I bought an S5 pad and used some copper tape I had lying around. NOTE: Copper tape (or at least the one I have) is only conductive on one side because of the adhesive. I rolled the ends up to make large contacts for the terminals on the phone and wireless charging pad.
I also removed the golden pins from the wireless charging pad because they were a bit thick. If you do this, be careful not to remove the silver pad underneath (I almost did).
See pictures attached, they're pretty explanatory.
The current pad I am using is a bit thick, and have ordered a new one, but it works! And it doesn't cost the earth.
Hope this helps people.
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
How does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
killbom said:
how does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
Click to expand...
Click to collapse
hi res picture 3mb
Thumb:
Hey guys,
It doesn't look as good as the post from DimonVideo, but as I said, I'm waiting on a thinner wireless model.
I'll put some pictures up later when I get home.
0.5mm Receiver
novastorm17 said:
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
Click to expand...
Click to collapse
I'm planning on getting this one.
Can't post the link to amazon as I do not have the minimum posts to do so.
Search this:
Alpha SlimPWRcard - 0.5mm Qi Receiver for Samsung Galaxy Alpha with integrated NFC coil
Those are the only model available for the Alpha. But since I don't live in USA, it would cost at least $50USD for me. So, I put together this thing
Where you get the pinout of the alpha wireless charger?

Categories

Resources