Hi,
I've somehow managed to brick my rooted S5830i while flashing a ROM onto it. I basically now want to get the phone back to the state it was in before attempting to flash it as I performed a backup beforehand.
I can't boot it into recovery, but I can into Download mode. I've been trying to use Odin3 v1.84 & 1.85 with a simple file installation, but when it does actually recognize the phone via the USB port (which is very temperamental) the installation gets stuck on "<ID:0/15> setupConnection". I've left it for 10+minutes without any luck.
Does anyone has any ideas where I can go from here? I've searched through this forum and others ones, but I can't find anyone else who's had this exact same issue.
I have to admit I am fairly new to all this, but surely if I can somehow get into recoverymode, where I have ClockworkMod installed, I can then easily perform a restore of my previous settings which i backed up on the SD card before I flashed the phone?
Any help would be great!
Cheers.
pilgrimads said:
Hi,
I've somehow managed to brick my rooted S5830i while flashing a ROM onto it. I basically now want to get the phone back to the state it was in before attempting to flash it as I performed a backup beforehand.
I can't boot it into recovery, but I can into Download mode. I've been trying to use Odin3 v1.84 & 1.85 with a simple file installation, but when it does actually recognize the phone via the USB port (which is very temperamental) the installation gets stuck on "<ID:0/15> setupConnection". I've left it for 10+minutes without any luck.
Does anyone has any ideas where I can go from here? I've searched through this forum and others ones, but I can't find anyone else who's had this exact same issue.
I have to admit I am fairly new to all this, but surely if I can somehow get into recoverymode, where I have ClockworkMod installed, I can then easily perform a restore of my previous settings which i backed up on the SD card before I flashed the phone?
Any help would be great!
Cheers.
Click to expand...
Click to collapse
Have you checked your usb drivers which must be properly installed?
because if they are not properly installed then these connection problems occur.
so reinstall usb drivers then perform.
Sent from my GT-S5830i using Tapatalk 2
Hitesh2626 said:
Have you checked your usb drivers which must be properly installed?
because if they are not properly installed then these connection problems occur.
so reinstall usb drivers then perform.
Sent from my GT-S5830i using Tapatalk 2
Click to expand...
Click to collapse
Thanks for your reply Hitesh,
I've re-installed the USB drivers and it does seem more stable now. I'm still however getting the following outcome, any ideas?
"<osm> Enter CS for MD5..
<osm> Check MD5.. Do not unplug the cable..
<osm> Please wait..
<osm> S5830iXXMD1_S5830iBTUMD1_S5830iXXMD1_HOME.tar.md5 is valid.
<osm> Checking MD5 finished Sucessfully..
<osm> Leave CS..
<id:0 015=""> Odin v.3 engine (ID:15)..
<id:0 015=""> File analysis..
<id:0 015=""> SetupConnection.."
Regards
pilgrimads said:
Thanks for your reply Hitesh,
I've re-installed the USB drivers and it does seem more stable now. I'm still however getting the following outcome, any ideas?
"<osm> Enter CS for MD5..
<osm> Check MD5.. Do not unplug the cable..
<osm> Please wait..
<osm> S5830iXXMD1_S5830iBTUMD1_S5830iXXMD1_HOME.tar.md5 is valid.
<osm> Checking MD5 finished Sucessfully..
<osm> Leave CS..
<id:0 015=""> Odin v.3 engine (ID:15)..
<id:0 015=""> File analysis..
<id:0 015=""> SetupConnection.."
Regards
Click to expand...
Click to collapse
Try with different firmware and check it again.
Sent from my GT-S5830i using Tapatalk 2
Hi,
Will the downloaded software and instructions work on a windows8 PC?
jeffers24 said:
Hi,
Will the downloaded software and instructions work on a windows8 PC?
Click to expand...
Click to collapse
Yes .
Hitesh2626 said:
Yes .
Click to expand...
Click to collapse
Thanks for quick response and that's a relief :victory:
Hi,
Loaded Samsung drivers from this link:-
http://http://forum.xda-developers.com/showthread.php?p=11633550
Which I got from this tutorial on how to unbrick my Ace which is stuck on Samsung logo screen:-
http://http://forum.xda-developers.com/showthread.php?t=1840645
Installed drivers on Windows 8, rebooted, put Ace into Odin link ready for download, connected via usb, PC reported error USB device not recognised, tried three different USB ports on PC, shows as unknown device.
Checked via control panel, Samsung drivers were installed.
Any ideas how I can sort out Samsung drivers on a Windows 8 PC
Finally got PC to recognise my ACEi which it recognised as a modem, which was good enough to let me follow the unbrick tutorial above and all worked, now have my ACEi working again.
Only real change I made was to use a different phone to USB cable
One unexpected big plus was that as well as getting the phone usable (would boot) it also restored my lost IMEI number so I can make calls etc. :victory: the IEMI number must have been on the phone somewhere as I have checked it and it is the one the phone came with.
I lost my IMEI number when I loaded the Jellyblast ROM and I did not do a backup first
I now have a fully working phone but want to load a different ROM.
Having learnt a lesson I have done a backup using CWM.
I want to protect my IEMI which I thought you could do by making a copy of the efs folder, however when I look in the efs folder it is empty!
Any idea on why my efs folder may be empty and how I can protect myself by making a backup of my IEMI that can be restored if it gets lost again after loading a new ROM?
Hitesh2626 said:
Try with different firmware and check it again.
Sent from my GT-S5830i using Tapatalk 2
Click to expand...
Click to collapse
I've tried again with different firmware and this time using the multi file option without a PIT file... this has now worked and the phone is operational again!!
Thanks for your help Hitesth
Related
I just started with odin to root for my first time, and droidstyle's guide says that "box in left hand corner of odin will say PASS". Which left hand corner? The bottom left with the box titled Message? All that box is telling me right after I pressed Start is <OSM> All threads completed. (succeed 0 / failed 0). Is this the equivalent of PASS, or do I need to try pressing Start again?
nevermind
just watched a video with some odin screen capture and can now see that odin never detected my device in the first place. not sure why, but at least now i know the issue. i am determined to make this work!
ETA: I now think I have an older version of Odin. What is the latest version that I should be using for windows 7? Mine says v1.3, but I just found v1.83. The link from droidstyles guide was for the older version.
i give up just for the night. I will come back to it some time tomorrow. For whatever reason, Odin is not finding my phone when I connect it and put it in download mode. I have the newer v1.83 now and that didn't change anything. is my pc somehow blocking it, maybe? idk.
ETA: another thought, could it be my usb cable? I no longer have a functional stock usb cable, I have replaced it with a belkin miniusb data/charger cable, which has worked fine for data and transferring files and such, until now. could that be it?
Sounds like you either do not have your phone in download mode or you don't have the proper Samsung drivers installed on your computer. Download mode should have the triangle.
Sent from my SCH-I500 using Tapatalk
download mode
I do have the triangle, that is not the problem. The problem is that Odin does not recognize that my phone is plugged in. My pc makes the audible noise that something has been plugged in, but from Odin I get nothing. I see on the videos I watched that the box in the upper left in Odin should turn yellow, but mine does not.
Sounds like it is either a driver issue or a non OEM cable issue. First uninstall and reinstall all Samsung drivers, if that doesn't fix it order a new cable from Samsung.
Sent from my SCH-I500 using xda premium
I reinstalled the usb driver and that allowed odin to find my device, but then after selecting my rom and pit files and pressing start a couple of windows popped up that just had the file directory for odin next to a caution type symbol with 'ok' the only option available to click, then after doing that in the two unexpected windows odin now displays
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI500_VZW_EH03_GB_CM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
is is not doing anything, my phone is still in download mode, and the start and reset buttons on odin are greyed out. what happened? do I have a bad version of odin? I am using v1.83. Did it do anything to my phone yet, is it in limbo, can I unplug my phone, should I start over? HELP!
ETA: I unplugged phone, closed odin, dowloaded it again from a different source, started over, now seems to be working fine. whatever. appears to be identical to the one I was just using.
Odin 1.3 is the version we all use for this phone. 1.8x might work but I haven't tried it.
Sent from my SCH-I500 using xda premium
It worked just fine. I watched some videos of others showing how to root and they all were using v1.8x, but I don't think Odin was my problem from the get go, it was my drivers.
I figured it was a driver issue.
Sent from my SCH-I500 using Tapatalk
Odin can be a pain in the ass. Glad you got it working.
If you want to remove one more variable for the future you can get a usb cable +charger for $2.50 shipped. I have ended up buying so many of these it's almost dumb since I always manage to lose them.
《SOLVED》Okay, so I was stuck in some sort of boot loop... after reading several posts on this site as well as many others I felt confident in my ability to repair it using Odin. Big Mistake!!! Now my phone will not go into recovery mode, or download mode it just shows me "phone--!--PC" As far as I can tell it is now hard bricked, my computer will not recognize it and I cannot not get away from the "phone--!--PC" screen to save my life. If anybody can help me I would be eternally grateful. Thanks!!
Which firmware are u on now?
Which files did u flash?
Try downloading a stock firmware for ur device from sammobile.com and flash it via odin.
"To err is human, to forgive is divine"
Sent from my SGS II
Which firmware are u on now?
Which files did u flash?
Try downloading a stock firmware for ur device from sammobile.com and flash it via odin.
I tried to follow the directions given here http://forum.xda-developers.com/showthread.php?t=1619571
Now I cant even get Odin to recognize my phone. I've tried everything and still can't get it into download mode anymore.
Used a USB jig?
"To err is human, to forgive is divine"
Sent from my SGS II
He doesn't need a jig. Phone---!---PC (or whatever order it's in) is download mode. Forced download mode. It's just a matter of getting the phone & PC to recognise each other like any other example of Odin not working.
MistahBungle said:
He doesn't need a jig. Phone---!---PC (or whatever order it's in) is download mode. Forced download mode. It's just a matter of getting the phone & PC to recognise each other like any other example of Odin not working.
Click to expand...
Click to collapse
Thanks for clearing that up! I remember gastonw saying it was a kind of download mode, that's why I suggested flashing first.
"To err is human, to forgive is divine"
Sent from my SGS II
I was finally able to get ODIN to recognize my phone, but still I can't get it to work. This is the message I'm getting and a big FAIL lol.
Any other advice???
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLSR_I9100GXXLSP_I9100GXEFLSR_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> cache.img
<ID:0/004> NAND Write Start!!
<ID:0/004> factoryfs.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
GTI9100G stuck in in boot and not charging!!!!!!!
AmadaWgnd said:
I was finally able to get ODIN to recognize my phone, but still I can't get it to work. This is the message I'm getting and a big FAIL lol.
Any other advice???
Click to expand...
Click to collapse
hello friends my phone is stuck in boot and not charging after updating through philz touch and ODIN is not recognising it!
what to do with it????
For boot loop, try wiping cache and dalvik cache I'm recovery.
For Odin fail, did your rom come with a pit file ? Did you check repartition ?
It is recommended not to repartition, but if the ROM contains a pit file, you may have to use it...
Anyway, you can try to reflash, change your USB port, use another USB cable, etc...
Envoyé depuis mon Nexus 10 avec Tapatalk
You stuck between those .img files? No choice. Go find .pit file with your stock firmware. You said you only get the pc and alert sign on the phone, right? Once you get the correct .pit, it will flash successfully. Wrong file, it will always stuck at .img, even if you wait for 2hours.
Sony Xperia Tipo ST21i
Turns out all I had to do was check repartition necause yes I did havr a PIT file with my rom... works great now. Thank u guys so much for all ur help!!
AmadaWgnd said:
Turns out all I had to do was check repartition necause yes I did havr a PIT file with my rom... works great now. Thank u guys so much for all ur help!!
Click to expand...
Click to collapse
Please add [SOLVED] to the title of ur post so that others may see ur solution.
"To err is human, to forgive is divine"
Sent from my SGS II
You're welcome!
Glad I was able to help and getting the right to post in the development thread doing so!
Have a nice day!
Envoyé depuis mon GT-I9100 avec Tapatalk
S2 GT I9100G Bricked
I (soft) bricked my GT-I9100G (following an attempt to install Slim ROM with CWM ROM Manager). I thought I was following instructions to the letter, but obviously hosed it up (somehow).
Background: This phone was rooted, with stock ICS ROM installed.
1. Phone only goes to “Samsung” screen,
2. Can only depower by removing the battery,
3. Cannot enter “Recovery” or “Download” modes,
4. Could not establish connection between Kies and phone - completely removed Kies,
5. Is recognized by Odin, and computer (with errors in Device Manager),
6. Drivers start to load, each time phone is connected but end up with “Driver Software was not successfully installed – Please consult with your device manufacturer…”,
7. I get Code 10 error when updating drivers in Windows 7,
8. I’ve tried flashing stock ROM (I9100GXXLSR_I9100GXXLSP_I9100GXEFLSR_HOME.tar.md5)using Odin PDA, but it goes to “Connection Setup..” and stops, leaving same “Samsung” screen image,
9. Then I flashed a stock PIT (omap4_all_20110627_emmc.pit), with the ROM – still only gets to “Connection Setup..” in Odin,
10. Followed all options in XDA thread: [SOLUTION] Samsung Mobile MTP Device -- CODE 10 error at Devicemanager – no change
Here are the messages that are on Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GXXLSR_I9100GXXLSP_I9100GXEFLSR_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
Have Removed/Updated Drivers (per #10, above). Used every possible combination of Ports and cables. Removed battery for one hour (replacing with fully charged battery).
I have been Googling for three days now without any solutions that fix this. Any assistance/advice will be most gratefully appreciated!!!!!
S/F Phillip
If you insist you've tried everything, then it's a service centre or local mobile repair shop job.
Or...You can find Hopper8's 'Odin troubleshooting' thread stickied in General & keep trying the stuff in that thread over & over & over. There's nothing else which isn't in the thread that can be suggested in these situations. They're either fixed with perseverance if they're recoverable, or they're NAND corrupted & require a motherboard replacement to fix.
Edit - And before you insist you've tried 'everything', you haven't tried multiple PC's yet, nor some other stuff in Hopper's thread.
hi,
i am running my phone on stock rom. its a region free phone, the standard international edition.
my phone suddenly got stuck at the boot logo, restarted it but still stuck.
couldn't get into recovery... vol up + power + home
download mode is working... vol down + power + home.
so i got the firmware from sammobile.com and got this tar.md5 file "I9300XXEMD3_I9300OJVEMC1_I9300XXEMA5_HOME.tar.md5"
so i have tried both odin 3.04 and 3.07, and i cant flash the firmware.
i get this error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEMD3_I9300OJVEMC1_I9300XXEMA5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Removed!!
please help me, is there something i am doing wrong or there is some other problem.
Do you have drivers installed? if yes than please close samsung PC SUITE from the system tray in your computer before you start odin. that might be the problem. best of luck
Chaitanyapatel8880 said:
Do you have drivers installed? if yes than please close samsung PC SUITE from the system tray in your computer before you start odin. that might be the problem. best of luck
Click to expand...
Click to collapse
yeah i just installed the drivers not the suite. the PC suite in not installed.
i have also never used KIES..i installed it just to try n restore my firmware but didnt use it and un-installed it. somehow dont like using it. prefer using ODIN. I am a samsung user since galaxy s 1 came out.
i am pretty sure its not a motherboard issue... as i can enter the download mode.
BTW can i just root it somehow, i have the CF root SGS 6.4 with me.
haseeb.sarwar said:
yeah i just installed the drivers not the suite. the PC suite in not installed.
i have also never used KIES..i installed it just to try n restore my firmware but didnt use it and un-installed it. somehow dont like using it. prefer using ODIN. I am a samsung user since galaxy s 1 came out.
i am pretty sure its not a motherboard issue... as i can enter the download mode.
BTW can i just root it somehow, i have the CF root SGS 6.4 with me.
Click to expand...
Click to collapse
try using cfroot with odin. hope it works
---------- Post added at 10:23 AM ---------- Previous post was at 10:22 AM ----------
haseeb.sarwar said:
yeah i just installed the drivers not the suite. the PC suite in not installed.
i have also never used KIES..i installed it just to try n restore my firmware but didnt use it and un-installed it. somehow dont like using it. prefer using ODIN. I am a samsung user since galaxy s 1 came out.
i am pretty sure its not a motherboard issue... as i can enter the download mode.
BTW can i just root it somehow, i have the CF root SGS 6.4 with me.
Click to expand...
Click to collapse
also try installing custom recovery using odin.
Basics read first.
http://forum.xda-developers.com/showthread.php?t=2344125
Critical you read the first two posts .
Hey there everyone
I'd be thankfull of someone could bring me some help with this problem. My phone has gone throw many shutdowns, in which somehow, the problem always solved itself, being that I left it charging the whole night, or that I tryed it out after a few days.
I own a Samsung Galaxy Y Pro since a couple of years now, and last night, while I was checking on my WhatsApp, it turned off itself. It usually happens, and annoys me, but turning it on again solves it... most of the times.
Now it didn't want to fully start. It got stuck at the black screen with the Samsung typography. I tryed to do a factory reset, and it only worsened the trouble. It froze at
-- Wiping dat...
Formating /data.
I left it like that a couple of hourse with no progress. I tryed to turn on the phone normally, but now it always takes me to that menu. I'm stuck, and it's the only way I can communicate with my family, so I beg someone of you to help me out, please.
I don't have any knowledge about Odin or sorts, nor programs to deal with the problem. So I'd ask if someone could explain me step by step what to do (or direct me to the thread where the troubleshooting is explained).
If you need some answers about my phone to understand the situation, I'll answer happily.
Thanks for reading this, and hope you have a nice day <3
have you rooted your phone?
if not, you may have to flash new stock rom from odin..
first you have to download stock rom base on you country here http://www.sammobile.com/firmwares/1/
then you have to download odin here https://mega.co.nz/#!UdRRyCAT!H4FyVxYynNWvXqRNmnpMGQRCP-dG3uykgP2pT4rh8Ek
for detail you can watch this video https://www.youtube.com/watch?v=HVLyjeqPtn0
i hope it would help you mate :fingers-crossed:
Hey there and thanks for answering!
My phone won't turn on normally, so I can't get the Triangle Away nor sync it with Odin. If I plug the USB to my phone at my computer, Odin won't recognize it neither. Any idea of what to do?
Have you installed latest driver? http://goo.gl/jzrFmO
Have you put your phone into download mode?
Hey there broke920!
Yes, the phone is now on downlaod mode, and the drivers you gave me made Odin regonize my phone (thank you!). How should I proceed?
You need to do this:
1) unzip rom file to obtain tar/tar.md5 file
2) click on PDA and select tar/tar.md5 file
3) click on START
It's throwing me this error.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> B5510LUBLF1_B5510PSNLF1_B5510LUBLF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am using Odin v3.07 and the rom that konohanz posted up there.
I don't know if this could help, but this is on the downloading screen on my phone.
PRODUCT NAME: GT-B5510L
CUSTOM BIN DOWN: NO (0 counts)
CURRENT BIN: SAMSUNG OFFICIAL.
Also, now when trying to access the phone normally, it shows an icon of an android, a box, and an arrow. Please help me out
Try with another version of Odin like 1.85 or 3.09 and disable antivirus software.
Both of them throw me the same error.
I may add that I think I messed up with the PIN. So maybe if I get that right, it will work out.
if may i suggest you try this one :
1. download latest philz recovery here https://goo.im/devs/philz_touch/CWM_Advanced_Edition/i9300/philz_touch_6.48.4-i9300.tar.md5/
2. make your phone to download mode
3. plug device then open odin you had
4. choose pda and open philz_touch_6.48.4-i9300.tar.md5
5. click start
if work you may flash rom that i use now here http://forum.xda-developers.com/galaxy-s3/development/rom-neatromlite-themed-aroma-mods-t2060403
download v7.9 and then flash it with philz_touch recovery and all will be normal, even better than the original stock rom you'll see :fingers-crossed:
Thanks everyone for your answers! I solved the problem, educating myself with the Odin program through the help that konohanz and broken920 gave me. Flashing with Odin worked, thanks to you two for the quick and accurate answers!
great job dude, you're welcome :victory:
Hello guys
I have a problem with my Galaxy tab 2 10.1 tab (gt-p5100), and i need to help for recovery it..
This is the problem: 3 days ago i was surf on the web, when the tab FREEZED !!!, then I restarted with the key combination Power and Down volume and the tablet was no longer running, remaining stuck on the word Start "Galaxy tab 2 10.1" !!!:crying::crying:
After a while I decided to flash the firmware installed with ODIN 03.04 then I put it in download mode and connect it to the PC, but when I press start remains long on "Setup connection" ... I'm sick and I disconnect the USB cable...response ? it remains fixed on this Image:
I can not do anything else..
then again I try to flash with Odin, and other firmware and combination but I always come out:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5100XXDMJ2_P5100ITVDMJ1_P5100XXDMG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
What do i do ?
I also tried to update with kies, but comes out:"the device does not support the initialization" :crying::crying::crying:
is it rooted it it is just install a rom on it go to recovery and install cyanogenmod or omni 4.4.4 then download stock i will upload stock for you if you want but i got to find it first on my computer
thehackerwhohacksandroid said:
is it rooted it it is just install a rom on it go to recovery and install cyanogenmod or omni 4.4.4 then download stock i will upload stock for you if you want but i got to find it first on my computer
Click to expand...
Click to collapse
TheHacker, thabks for reply...as recovery? this is the problem, I can not access any recovery, the tablet remains fixed on that image I press any button, although Odin sees it, and I try to flash recovery or firmware stock but Odin always fails writing and I have tried several versions of Odin...
what can I do ?
tanohack said:
TheHacker, thabks for reply...as recovery? this is the problem, I can not access any recovery, the tablet remains fixed on that image I press any button, although Odin sees it, and I try to flash recovery or firmware stock but Odin always fails writing and I have tried several versions of Odin...
what can I do ?
Click to expand...
Click to collapse
Did you try running odin as administrator in Windows? That sometimes helps.
Olivier V said:
Did you try running odin as administrator in Windows? That sometimes helps.
Click to expand...
Click to collapse
YES !
tanohack said:
YES !
Click to expand...
Click to collapse
Perhaps an older version of Odin? Have you tried looking for an answer in the correct forum as this is the forum for the old tab 1, not the 2 like yours.
Sent from my Z1 Compact
Olivier V said:
Perhaps an older version of Odin? Have you tried looking for an answer in the correct forum as this is the forum for the old tab 1, not the 2 like yours.
Sent from my Z1 Compact
Click to expand...
Click to collapse
I have try all old version and new of ODIN and "WORK" only with 3.07 !!!!!!!!!! this version of Odin flash the firmware correctly but on reebot the write "Firmware upgrade issue" remain !!!!!!!!!!!!!!!!! absurd..
..now move to galaxy tab 2 topic
other ideas ?