How to Uninstall Chainfire 3D on bricked Devices ...
Here is the solution
1. Connect USB cable and then restart your phone.Get your phone in Recovery Mode....
2. Check whether your device has been detected in the PC - Device Manager - Android ADB Interface.
2. Run "adb devices" - to make sure the phone drivers are ok (should output a long hex string and "device"). If Device Isn't Detected You need to install Adb Drivers... Download From: adbdriver.com
3. Run "adb shell" from command prompt. If $ came then Type SU. so it will automatically change to #. ( Means your phone rooted and you gain root permission to delete the Bloody CF3D driver from your phone.
*Tip*If You Get An Error Type "# mount -o rw,remount /system" - Press Enter.
4. Still in shell? Type "sh /cf3d_uninstall.sh"
*Tip*if sh /cf3d_uninstall.sh doesnt work , try 'sh /system/lib/cf3d_uninstall.sh" instead.
Phone will automatically reboot and will be ready.
Don't Forget To press Thanks.....
:victory::victory::victory::victory::victory::victory::victory::victory:
N'ayam Amarsh'e said:
How to Uninstall Chainfire 3D when bricked Device ...
Here is the solution
1. Connect USB cable and then restart your phone.Get your phone in Recovery Mode....
2. Check whether your device has been detected in the PC - Device Manager - Android ADB Interface.
2. Run "adb devices" - to make sure the phone drivers are ok (should output a long hex string and "device").
3. Run "adb shell" from command prompt. If $ came then Type SU. so it will automatically change to #. ( Means your phone rooted and you gain root permission to delete the Bloody CF3D driver from your phone.
4. (only for users which have ADB locked or get Operation not Permitted).Then type # mount -o rw,remount /system - Press Enter.
5. Still in shell "sh /cf3d_uninstall.sh"
if sh /cf3d_uninstall.sh doesnt work , try 'sh /system/lib/cf3d_uninstall.sh" instead.
Phone will automatically reboot and will be ready.
:victory::victory::victory::victory::victory::victory::victory::victory::victory:
Click to expand...
Click to collapse
I have my device bricked with Chainfire 3d but when I use adb devices it does not show anything and also it is in Recovery mode.
jxgreat said:
I have my device bricked with Chainfire 3d but when I use adb devices it does not show anything and also it is in Recovery mode.
Click to expand...
Click to collapse
Hi ,
Do You Turned ON USB DEBUGGING If Yes then....
I think you don't have ADB drivers installed... Here You Go - http://adbdriver.com/upload/AdbDriverInstaller.exe
IF NOT
Then I am sorry i can't help, also which phone do you have??
N'ayam Amarsh'e said:
Hi ,
Do You Turned ON USB DEBUGGING If Yes then....
I think you don't have ADB drivers installed... Here You Go - http://adbdriver.com/upload/AdbDriverInstaller.exe
IF NOT
Then I am sorry i can't help, also which phone do you have??
Click to expand...
Click to collapse
No I didn't.
I have Huawei Ascend Y320 U30.
So what should I do now? Through this mobile in junk? I just brought it couple of days ago.
My pc didn't detect any devices when I connecting asus memopad 8 in recorvery mode
is this will work with motorola razr d3 xt919 its bricked with chainfire and please can you give the link of what i neet for this thank you
---------- Post added at 09:48 AM ---------- Previous post was at 09:40 AM ----------
And yes i wiped dilveck cache and factory reset now what will happen please help me
N'ayam Amarsh'e said:
How to Uninstall Chainfire 3D when bricked Device ...
Here is the solution
1. Connect USB cable and then restart your phone.Get your phone in Recovery Mode....
2. Check whether your device has been detected in the PC - Device Manager - Android ADB Interface.
2. Run "adb devices" - to make sure the phone drivers are ok (should output a long hex string and "device").
3. Run "adb shell" from command prompt. If $ came then Type SU. so it will automatically change to #. ( Means your phone rooted and you gain root permission to delete the Bloody CF3D driver from your phone.
4. (only for users which have ADB locked or get Operation not Permitted).Then type # mount -o rw,remount /system - Press Enter.
5. Still in shell "sh /cf3d_uninstall.sh"
if sh /cf3d_uninstall.sh doesnt work , try 'sh /system/lib/cf3d_uninstall.sh" instead.
Phone will automatically reboot and will be ready.
:victory::victory::victory::victory::victory::victory::victory::victory::victory:
Click to expand...
Click to collapse
I have viewsonic vb734 tablet running gingerbread ROM , its a Chinese tablet. i have root access but I wasn't able find custom recovery , thats why i didn't made nandroid backup , so the thing is that I installed chainfire 3d and now I am stucked on boot loop without any recovery , Is there any way to fix it ? Thanks
heres the link of my device, http://forum.xda-developers.com/showthread.php?t=1393128
huzaifahaziz said:
I have viewsonic vb734 tablet running gingerbread ROM , its a Chinese tablet. i have root access but I wasn't able find custom recovery , thats why i didn't made nandroid backup , so the thing is that I installed chainfire 3d and now I am stucked on boot loop without any recovery , Is there any way to fix it ? Thanks
heres the link of my device, http://forum.xda-developers.com/showthread.php?t=1393128
Click to expand...
Click to collapse
You dont need a custom recovery you can do it with stock ones also
sir tnx for this guide it will help me to unbrick my galaxy y
Thanks
N'ayam Amarsh'e said:
You dont need a custom recovery you can do it with stock ones also
Click to expand...
Click to collapse
Okay, I Will try it .. thanks for the help
hello, please help me I also installed Chainfire 3D on my phone and now it is stuck on the booting screen. please tell what should i do? My device is Lava Iris 404e.
learner4 said:
hello, please help me I also installed Chainfire 3D on my phone and now it is stuck on the booting screen. please tell what should i do? My device is Lava Iris 404e.
Click to expand...
Click to collapse
Did you read post #1? Followed the steps? Should solve your problem.
PS: You can reflash your rom/firmware, it will for sure get rid of CF3D and this bootloop, too.
PS2: I googled your phone model, it runs Android 4.2. CF3D supports officially only 2.1 - 2.3.
Enviado de meu Nexus 4 usando Tapatalk
Yes i tried that step but it gives an error saying that directory not found. I also tried to find the stock rom for my device but its not there on any of the website.
Hey thanks! Now my phone is working. What i needed to do was that when i rebooted my device in recovery mod and plugged it in my pc, my device was not detected even when i installed latest drivers for my device. But when i rebooted my device in factory mode, it was detected so i was able to fix it.:laugh:
Can't access to adb shell
N'ayam Amarsh'e said:
How to Uninstall Chainfire 3D when bricked Device ...
Here is the solution
1. Connect USB cable and then restart your phone.Get your phone in Recovery Mode....
2. Check whether your device has been detected in the PC - Device Manager - Android ADB Interface.
2. Run "adb devices" - to make sure the phone drivers are ok (should output a long hex string and "device").
3. Run "adb shell" from command prompt. If $ came then Type SU. so it will automatically change to #. ( Means your phone rooted and you gain root permission to delete the Bloody CF3D driver from your phone.
4. (only for users which have ADB locked or get Operation not Permitted).Then type # mount -o rw,remount /system - Press Enter.
5. Still in shell "sh /cf3d_uninstall.sh"
if sh /cf3d_uninstall.sh doesnt work , try 'sh /system/lib/cf3d_uninstall.sh" instead.
Phone will automatically reboot and will be ready.
:victory::victory::victory::victory::victory::victory::victory::victory::victory:
Click to expand...
Click to collapse
I'm pretty sure that my device is detected. But when i type "adb shell", its says, ' /sbin/sh/' failed: permission denied <13>
What do i do? Please help guys!!
I just bricked my device need a stock rom of Alps GT-I9600 mt6572 device
I just bricked my device need a stock rom of Alps GT-I9600 mt6572 device
please someone help me. I'll be great full to you Thanks in advance....and sorry for bad english :crying:
Great Work - Favor to Ask
N'ayam Amarsh'e said:
How to Uninstall Chainfire 3D when bricked Device ...
Here is the solution
1. Connect USB cable and then restart your phone.Get your phone in Recovery Mode....
2. Check whether your device has been detected in the PC - Device Manager - Android ADB Interface.
2. Run "adb devices" - to make sure the phone drivers are ok (should output a long hex string and "device").
3. Run "adb shell" from command prompt. If $ came then Type SU. so it will automatically change to #. ( Means your phone rooted and you gain root permission to delete the Bloody CF3D driver from your phone.
4. (only for users which have ADB locked or get Operation not Permitted).Then type # mount -o rw,remount /system - Press Enter.
5. Still in shell "sh /cf3d_uninstall.sh"
if sh /cf3d_uninstall.sh doesnt work , try 'sh /system/lib/cf3d_uninstall.sh" instead.
Phone will automatically reboot and will be ready.
:victory::victory::victory::victory::victory::victory::victory::victory::victory:
Click to expand...
Click to collapse
Nice clear instructions - Ran into a problem - Believe the cf3d_uninstall.sh is corrupt and desperatly need a copy - Definite donation your way - Thanks!
j518 said:
Nice clear instructions - Ran into a problem - Believe the cf3d_uninstall.sh is corrupt and desperatly need a copy - Definite donation your way - Thanks!
Click to expand...
Click to collapse
Thanks to say but I don't take Donations But Can't give you the file now ... You can reequest someone to pull the file for you... or I think the file isn't corrupt something other is wrong... it generally doesn't happen or It never has happened...
jepoy75 said:
I'm pretty sure that my device is detected. But when i type "adb shell", its says, ' /sbin/sh/' failed: permission denied <13>
What do i do? Please help guys!!
Click to expand...
Click to collapse
This means your phone isn't rooted properly... that's why it shows error...
learner4 said:
hello, please help me I also installed Chainfire 3D on my phone and now it is stuck on the booting screen. please tell what should i do? My device is Lava Iris 404e.
Click to expand...
Click to collapse
Follow My guide....Simple???
Related
Hi all,
please tell me how can i root my android device without using of any other application like superoneclick or superuser.
i have sony xperia 10 mini
please help me for this.
thanks in advance.
Have you had a look in the x10 forums?
Why do you not want to use superoneclick? It makes life a lot easier. And superuser is an app that you install during the rooting process to give root apps root access to your phone, its pretty much essential.
And also worng section should be in x10 Q&A
Sent from an ice cream sandwich
[email protected] said:
Hi all,
please tell me how can i root my android device without using of any other application like superoneclick or superuser.
i have sony xperia 10 mini
please help me for this.
thanks in advance.
Click to expand...
Click to collapse
you can use super one clicks, it can root also unroot...i used it for my galaxy mini
i don't want to use any third party application for rooting.
i want to root the my android phone using me application.
please tell me if there is any option of this.
The only other way to root is by using adb here are the instructions http://forum.xda-developers.com/showthread.php?t=739874.
Sent from an ice cream sandwich
when i execute this line from cmd
adb push Superuser.apk /sdcard/Superuser.apk
it return error: device not found
and adb devices also return no device list
[email protected] said:
when i execute this line from cmd
adb push Superuser.apk /sdcard/Superuser.apk
it return error: device not found
and adb devices also return this error (device not found).
Click to expand...
Click to collapse
Did you instal the usb drivers?
Did you enable usb debugging on your device?
Did you connect your device?
Ommadawn101 said:
Did you instal the usb drivers?
Did you enable usb debugging on your device?
Did you connect your device?
Click to expand...
Click to collapse
yes i do all these
[email protected] said:
yes i do all these
Click to expand...
Click to collapse
When you connect your device to your pc, make sure you DO NOT select to mount it (or whatever term is used on your operating system)
and then, if you type on the command line:
adb devices
you should get a result with a device list
if you get no devices, then either you did not install adb, or the usb drivers properly
Follow this to find out if you installed adb properly
http://adrynalyne.us/files/How to install adb.pdf
Ommadawn101 said:
When you connect your device to your pc, make sure you DO NOT select to mount it (or whatever term is used on your operating system)
and then, if you type on the command line:
adb devices
you should get a result with a device list
if you get no devices, then either you did not install adb, or the usb drivers properly
Follow this to find out if you installed adb properly
http://adrynalyne.us/files/How to install adb.pdf
Click to expand...
Click to collapse
when i m connected my samsung mobile its adb interface display in device manager in section of ADB Interface,and adb devices command return the samsung device
but when i connect the sony phone with same method firstly its not display in section of ADB interface in device manager, its display in Sony Ercssion sa0101 section.
and when i run adb devices on cmd its not return any device.
and i found one thing when i use SuperOneClick application and use its root option.
than run adb devices on cmd now its return the sony device and not its work fine.
so i want to connect it from my application without the help of SuperOneClick
please help me what can i do.
[email protected] said:
when i m connected my samsung mobile its adb interface display in device manager in section of ADB Interface,and adb devices command return the samsung device
but when i connect the sony phone with same method firstly its not display in section of ADB interface in device manager, its display in Sony Ercssion sa0101 section.
and when i run adb devices on cmd its not return any device.
and i found one thing when i use SuperOneClick application and use its root option.
than run adb devices on cmd now its return the sony device and not its work fine.
so i want to connect it from my application without the help of SuperOneClick
please help me what can i do.
Click to expand...
Click to collapse
I am not sure I am following you.
If you already used superoneclick and it worked for you, why do you need another way of doing it, without superoneclick?
Also, I don't have any of your devices, so I cannot advise you on them.
Sorry
please understand how can i advice to other use any other application for rooting when he used my application.
My phone has a major problem. I'll explain the steps I took to screw it up this badly.
1.) Root phone and install a ICS rom
2.) Market doesnt work so I reinstall another market/vending.apk app from mediafire
3.) Market still didnt work so I install another rom
4.) Then I use that rom and rom manager is gone so I install another one I downloaded form mediafire.
5.) That rom manager only verifies my phone as a optimus c but i still installed clockwork mod
6.) The version Clockwork mod does not work
7.) I installed Xionia recovery instead
8.) I accidentally, in xionia, do a factory reset that bricks my phone.
9.) I could still use adb to force files on and try to recovery the phone by flashing files
10.) I flash a recovery image file and now here is the HUGE problem
11.) MY PHONE WONT BOOT UP AT ALL, ALL THAT SHOWS IS THE LG SYMBOL AND THEN BLANK SCREEN. WHEN I HOLD DOWN,POWER,HOME IT DOES THE SAME THING (BLANK SCREEN). AND WHEN I TRY TO USE ADB I GET THAT MY PHONE IS CONECTED BUT,
c:\adb devices
List of devices attacched
A100001944D988 recovery
Then I try ADB shell
C:\adb shell
But I get
/ #
and i cant complete any commands
when i try adb remount
C:\adb remount
remount failed: Invalid Argument
Can Someone Please Help
Same issue
Maybe the Virgin Mobile Store will just give me a new phone cause there is no actual proof that I rooted the phone.
Before trying this method be 100% sure that recovery is not working hold volume down + power + home continuously for around one minute if u get fastboot error, follow this - http://forum.xda-developers.com/showthread.php?t=1088046thread but still if u see nothing u have to use kdz method http://forum.xda-developers.com/showthread.php?t=883314 or see this link for a picture guide - http://forum.xda-developers.com/showthread.php?t=1060121
Sent from my LG-P500 using Tapatalk
Sent from my LG-P500 using Tapatalk
Hello. This is my 2nd post after here. I hope this will not bother anybody.
I have a situation. I did root my TF201 using CWM and virtuous_prime_s_9.4.2.21_v1 a month ago. Just now, I plan to sell my TF201. So, I go to the tablet setting and click at the reset data or something like that. I think it's just a normal data deletion process which is not effecting the rooted system. Unfortunately, after I reset / delete the data, the tablet is not going to boot. It just keep showing the CWM Recovery page with options to reboot the system, install zip from sdcard, wipe data, and so on. I selects to reboot the system, but nothing is happening. The tablet is turned off and turned back on with same display (CWM Recovery page).
What should i do?
titanbullet said:
Hello. This is my 2nd post after here. I hope this will not bother anybody.
I have a situation. I did root my TF201 using CWM and virtuous_prime_s_9.4.2.21_v1 a month ago. Just now, I plan to sell my TF201. So, I go to the tablet setting and click at the reset data or something like that. I think it's just a normal data deletion process which is not effecting the rooted system. Unfortunately, after I reset / delete the data, the tablet is not going to boot. It just keep showing the CWM Recovery page with options to reboot the system, install zip from sdcard, wipe data, and so on. I selects to reboot the system, but nothing is happening. The tablet is turned off and turned back on with same display (CWM Recovery page).
What should i do?
Click to expand...
Click to collapse
If you still have the virtuous prime file on there just.go to install zip and select it then reflash and youl be good to go. If not then you need to search on here for a program called knives and forks which is the easy way to install adb android debug bridge once installed download virtuous prime zip and place it in the same Rwhere you just installed adb then make sure you are in the cmw main screen and type adb push (filename) this will send the to tablet it may take up to 10 minutes and will just show a flashing cursor . Then flash.as normal. Sorry for spelling mistakes typing.g this on my phone and its being stupid
Uberjim said:
If you still have the virtuous prime file on there just.go to install zip and select it then reflash and youl be good to go. If not then you need to search on here for a program called knives and forks which is the easy way to install adb android debug bridge once installed download virtuous prime zip and place it in the same Rwhere you just installed adb then make sure you are in the cmw main screen and type adb push (filename) this will send the to tablet it may take up to 10 minutes and will just show a flashing cursor . Then flash.as normal. Sorry for spelling mistakes typing.g this on my phone and its being stupid
Click to expand...
Click to collapse
Thanks for the reply. I appreciate the info given. Will try to use the tool now since the rom file is no longer saved in the tablet.
Will update soon.
Thanks.
I'm just done installing the Knivesandforks on my win7. After that, the system automatically install the phyton. I dont know what its function, but as i follow this steps, i get error with cmd which shown as below:
Code:
c:\users\pc>adb reboot
error: device not found
i think i didn't miss any steps. Anybody here could help me with this?
Thanks in advance.
* my tablet is still in cmw main page and not showing anything even has been connected to the PC. i think that's the reason why the error occurs - device not found. anybody who could give some ideas on this will much appreciated.
You may need the fast boot drivers I wasn't sure if you would with being in cmw download those and extract them to the same folder as adb then load it up by using shift right mouse click run command and type and type adb devices if it shows up your good to go try the above steps again
titanbullet said:
Hello. This is my 2nd post after here. I hope this will not bother anybody.
I have a situation. I did root my TF201 using CWM and virtuous_prime_s_9.4.2.21_v1 a month ago. Just now, I plan to sell my TF201. So, I go to the tablet setting and click at the reset data or something like that. I think it's just a normal data deletion process which is not effecting the rooted system. Unfortunately, after I reset / delete the data, the tablet is not going to boot. It just keep showing the CWM Recovery page with options to reboot the system, install zip from sdcard, wipe data, and so on. I selects to reboot the system, but nothing is happening. The tablet is turned off and turned back on with same display (CWM Recovery page).
What should i do?
Click to expand...
Click to collapse
Recovery bootloop, see here, option 1a: http://forum.xda-developers.com/showthread.php?t=1514088
Use only Universal Naked Drivers (see related thread).
Sometimes even with proper drivers adb is a mess, then uninstall adb and search the net for a ready to use adb, there are some easy to find.
Uberjim said:
You may need the fast boot drivers I wasn't sure if you would with being in cmw download those and extract them to the same folder as adb then load it up by using shift right mouse click run command and type and type adb devices if it shows up your good to go try the above steps again
Click to expand...
Click to collapse
i did those steps again, but it seems like not helping. the script is only rebooting the tablet instead of giving me the option to flash the rom. i don't know if i did wrong. but as i know, i did as posted here.
* frust to see the cmw recovery for the whole day
Striatum_bdr said:
Recovery bootloop, see here, option 1a: http://forum.xda-developers.com/showthread.php?t=1514088
Use only Universal Naked Drivers (see related thread).
Sometimes even with proper drivers adb is a mess, then uninstall adb and search the net for a ready to use adb, there are some easy to find.
Click to expand...
Click to collapse
i did follow this tutorial
at first, install universal naked drivers - done
Now do the following:
Make sure your Prime is in Recovery mode (CWM) - YES
Open a cmd line on your pc - DONE
Type: "adb shell" - DONE
You should see a "#" now - YES
Once you have that "#", please type: dd if=/dev/zero of=/dev/block/mmcblk0p4 bs=100 count=1 and press [Enter] - Ok. This part was very difficult. I see the "#" but to type all those command, I can't. Why? Because the line in cmd instantly extended to a new line of command. I mean it just like I press the ENTER button. So, the line move to below and i can't finish typing all those command.
Now type: dd if=/dev/zero of=/dev/block/mmcblk0p3 bs=16 count=1 and press [Enter]
Exit the shell and reboot your Prime via CWM
It should not reboot to CWM automatically now. It either boots your ROM or is stuck at the splash screen. If it is stuck, boot to recovery and install any ROM you want.
Click to expand...
Click to collapse
titanbullet said:
i did follow this tutorial
at first, install universal naked drivers - done
Click to expand...
Click to collapse
Very strange, try to expand your command line window first. It doesn't matter if the text goes on following line, as long as you don't press Enter it's considerd as the same line. Try copy/paste instead ot typing.
Striatum_bdr said:
Very strange, try to expand your command line window first. It doesn't matter if the text goes on following line, as long as you don't press Enter it's considerd as the same line. Try copy/paste instead ot typing.
Click to expand...
Click to collapse
this is my first time, so i don't know if that was strange. ha ha. well, it's not about the command line which is extended or not. but the line itself creating a new line, as i said - just like i press the ENTER button.
i try to use copy-paste function (ctrl + c and ctrl + v). but i don't think it functions in cmd.
please help..
[Solved]
What i do?
I follow this step again
Installing the ADB again
And the most important thing is, pushing ROM into /sdcard should be like this:
Code:
adb push rom.zip /sdcard/rom.zip
And right-click copy paste function solving my strange cmd
Then i just follow the steps by installing the zipped rom thru cwm when my screen did not stuck at splash screens
Thanks for your kindness
My TF is now back to normal
THANKS!
My phone is from chinavasion it is galaxy i8550 WIN clone with lower specs it is mocor droid 2.0.5 with a fake jellybean speadtrum sc6820 it is rooted i connected the phone via adb and reboot into recovery i have stock recovery not cwm and i tried fixing it btw i meessed up my build.prop file but anyways i tried to fix it via adb and i got a permission error and i have a backup of my build.prop tho ...i just gave up and rebooted to recovery and wiped data/factory reset and ofcourse it didnt work but i lost my adb drivers i cant turn on usb debugging so i cant use adb and i dont know how to accesss recovery i keep ending up in the speadtrum factory test where u test phone hardware nothing else please help if u can altho i highly doubt it and also when i used adb to reboot in recovery and used a zip file it would say signature verification failed :crying::fingers-crossed: But i trust in xda please help even to give me the phone combination keys to recovery and that give me a zip that will be accepted PLEASE i only had the phone for a month
What exactly were you trying to fix in your stock recovery? Assuming I understand you correctly?
Sent from my K2_CL using Tapatalk
Fixing
Modding.MyMind said:
What exactly were you trying to fix in your stock recovery? Assuming I understand you correctly?
Sent from my K2_CL using Tapatalk[/QUOT
I just fugured out something the problem occured when i took a backup of my build.prop (original one) from my sd card and replaced it with the one in my system folder and forgot to add permissions to it and i restarted my phone and now its bootlooped. When it happened i tried to fix it before i factory reset my phone and lost access to recovery cuz i use to access it from adb i tried to flash a new one (build file) but i got signature verification failed so i just factory reset and lost my adb drivers so now i cant connect it to my computer to use adb commands to reboot into recovery and idk my combination for recovery it is speadtrum sc6820 .....ps. my phone is rooted and has mocor droid 2.3.5 with 4.2.2 jellybean so u know its a fake jellybean cuz its a cloned phone and i have no cwm :crying:
Click to expand...
Click to collapse
@BenDroid1
You can write the custom recovery to your recovery partition using dd in an android terminal emulator from the play store. You would need to know which partition holds your recovery.
For MY device (your partition is different) it would be as followed in the terminal emulator:
Code:
su
Code:
dd if=/sdcard/customrecovery.img of=/dev/block/mmcblk0p21
/dev/block/mmcblk0p20 is the partition that holds my recovery on my device - yours will be different!
You can also use this method for the boot.img towards the boot partition as well as data to data partition, and so forth.
If you have CWM and you were smart enough to create a backup of your device, then I would write the custom recovery to your recovery partition, boot in to CWM, and restore your device with your backup. Then, reboot, plug device in to your computer, allow the computer to reinstall the drivers and hopefully at this point you should be able to establish connection with adb/fastboot again.
Sent from my K2_CL using Tapatalk
Example 1
Sent from my K2_CL using Tapatalk
Example 2
Sent from my K2_CL using Tapatalk
Cant do that
How do uexpect me to do all of that when everytime i boot my phone the its stuck on the logo and i Dont have cwm ...my phone is bootlooped
BenDroid1 said:
Modding.MyMind said:
What exactly were you trying to fix in your stock recovery? Assuming I understand you correctly?
Sent from my K2_CL using Tapatalk
Click to expand...
Click to collapse
When it happened i tried to fix it before i factory reset my phone and lost access to recovery cuz i use to access it from adb i tried to flash a new one (build file) but i got signature verification failed so i just factory reset and lost my adb drivers so now i cant connect it to my computer to use adb commands to reboot into recovery and idk my combination for recovery it is speadtrum sc6820 .....
Click to expand...
Click to collapse
Because right here according to your quote you mentioned that you resetted your device, lost connection to your adb. Only time you can use ADB is when your phone is running. Only way you can confirm if you lost connection with ADB is if your phone is up and running, you open up command window on pc, then run 'adb devices' and if nothing returns then you have no connection. Otherwise, there is no way to confirm if you lost connection to it. So by your quote above, you made it sound like you got around your bootloop problem but could not connect with using ADB and no longer had CWM on your device.
Try to be more clear next time lol.
Have you tried using fastboot instead of ADB?
Sent from my K2_CL using Tapatalk
Modding.MyMind said:
Because right here according to your quote you mentioned that you resetted your device, lost connection to your adb. Only time you can use ADB is when your phone is running. Only way you can confirm if you lost connection with ADB is if your phone is up and running, you open up command window on pc, then run 'adb devices' and if nothing returns then you have no connection. Otherwise, there is no way to confirm if you lost connection to it. So by your quote above, you made it sound like you got around your bootloop problem but could not connect with using ADB and no longer had CWM on your device.
Try to be more clear next time lol.
Have you tried using fastboot instead of ADB?
Sent from my K2_CL using Tapatalk
Click to expand...
Click to collapse
no i havent and sorrry i ...i will be clearer when i press power plus volme up i get speadtrum factory test where u test phone hardware but no android recovery
Your phone has a bootloader. You need to access your bootloader, select fastboot, plug your device in your pc, open up command window, then type 'fastboot devices'.
If you get your device serial number returned back to you then you have connection. If it returns blank, then you do not have connection which at this point I will not be able to help you.
Sent from my K2_CL using Tapatalk
Modding.MyMind said:
Your phone has a bootloader. You need to access your bootloader, select fastboot, plug your device in your pc, open up command window, then type 'fastboot devices'.
If you get your device serial number returned back to you then you have connection. If it returns blank, then you do not have connection which at this point I will not be able to help you.
Sent from my K2_CL using Tapatalk
Click to expand...
Click to collapse
unfortunately looks like u cant help me cuz neither that wont showup
BenDroid1 said:
unfortunately looks like u cant help me cuz neither that wont showup
Click to expand...
Click to collapse
I'm sorry bro. Maybe someone else on here will pickup where I left off. Good luck friend.
Sent from my K2_CL using Tapatalk
Hey, I'm french so if I do mistake, it's normal, sorry
Here is a way to root this Wiko, finally!
Before doing this, i want to say that me, XDA or nobody exept you is responsible of what you can do on your phone, this method work for me, surely for you, but this operation will delete all your data, so remember to backup your data.
Now, you Have to go to Developper options, enable "OEM Unlocking", "USB Debugging" and disable "Verify apps over USB"
After, set "Select USB Configuration" to MTP. After That, download file (https://mega.nz/#!ioBQDZra!z6ntj85aM-mjg4dnscPaPBjvd-qpSY9HQiDkKuYbxcU) and extract it
Connect your phone to your Computer, Copy and Paste the SuperSU zip file in your SD card, and reboot your phone in fastboot mode (shutdown, and boot it by pressing Power and Vol+, then, when you have a choice between recovery and fastboot, select fastboot by clicking Vol-)
Open a command prompt in the extracted file, and type: fastboot oem unlock
Here, all your data will be lost by a factory reset.
When the phone restart, in the command prompt, type:
adb root
adb shell
cat /proc/partitions
ls -l /dev/block/platform/soc/7825900.sdhci/by-name/ (7825900.sdhci may be different, so use tab to find the correct file)
in the list, you will have a file with "recovery -> /dev/block/XXX" (XXX may be like mmcblk0p22)
cat /dev/block/XXX > /data/local/tmp/recovery.img
exit
adb pull /data/local/tmp/recovery.img
adb reboot-bootloader
fastboot flash recovery "CUSTOM recovery.img"
fastboot reboot
if there is no problems, you phone restart normally, so stop it, and boot to the recovery (Power and Vol+ and whene the choice appear, Select recovery with Vol+)
if your phone don't want to boot to the TWRP recovery, try to flash the stock recovery, reboot and flash again the custom one. if the problem persist, leave a comment.
In TWRP, swipe the button, and go to Install, Up a level, select external_sd and then, select the SuperSU file, select "Reboot after installation is complete, and swipe to flash.
When it's done, install or not the TWRP app, and reboot. The device can start twice before finally boot, and can be longer than usual, but don't do anything, it's normal.
When the phone finally boot, SuperSU may be installed, so go check if it's true, and if it is, go to the play store and install BusyBox (by Stephen (Stericson))
After the installation is complete, open it, and click install.
If there is no problem, the root acces will be request, so accept it and all is done.
If you have a problem, or any question, ask me.
Anyone a idea how to root a Wiko View 3 Lite?
give me the link, pls
greenverdy said:
give me the link, pls
Click to expand...
Click to collapse
Ok
Root Wiko View
Hi,
Can you send the link for rooting Wiko view.
Thanks in advance.
give me the link Please.
can you send me the link as well?
Please if someone has the package already, kindly posted it on the forum.
zerking said:
can you send me the link as well?
Please if someone has the package already, kindly posted it on the forum.
Click to expand...
Click to collapse
Ok, no problem
thank you for the link. I got both TWRP and SU installed but the device is not rooted? How can it be?
zerking said:
thank you for the link. I got both TWRP and SU installed but the device is not rooted? How can it be?
Click to expand...
Click to collapse
Do you have an error message ? Or something else ?
Oh, well, it figured my way out! First SU installation, the phone isn't rooted (I don't know why, either). But I factory reset the phone, set the phone up, then go to TWRP and re-install SU and it worked. Now the phone is rooted!
Thank you very much for your guide and files.
By the way, I guess most people will get stuck at "adb root" command.
Simply dial *#*#84666364#*#* (this launches TinnoEngineerMode)
- go to "Tinno Debug Feature"
- tap on "persist.tinno.debug" and choose 1
Then you can go on with "adb root" command
Hope this helps!
zerking said:
Oh, well, it figured my way out! First SU installation, the phone isn't rooted (I don't know why, either). But I factory reset the phone, set the phone up, then go to TWRP and re-install SU and it worked. Now the phone is rooted!
Thank you very much for your guide and files.
By the way, I guess most people will get stuck at "adb root" command.
Simply dial *#*#84666364#*#* (this launches TinnoEngineerMode)
- go to "Tinno Debug Feature"
- tap on "persist.tinno.debug" and choose 1
Then you can go on with "adb root" command
Hope this helps!
Click to expand...
Click to collapse
It's a good think to say it, because it don't work without dialing this number. Thanks
zerking said:
Oh, well, it figured my way out! First SU installation, the phone isn't rooted (I don't know why, either). But I factory reset the phone, set the phone up, then go to TWRP and re-install SU and it worked. Now the phone is rooted!
Thank you very much for your guide and files.
By the way, I guess most people will get stuck at "adb root" command.
Simply dial *#*#84666364#*#* (this launches TinnoEngineerMode)
- go to "Tinno Debug Feature"
- tap on "persist.tinno.debug" and choose 1
Then you can go on with "adb root" command
Hope this helps!
Click to expand...
Click to collapse
On latest wiko view update, tinoo debug feature was gone, we can't use adb root again after update
guys where i can download official rom for the wiko view 2 and extract?
ola and in french plz ?
don´t work on my wiko view 32GB
please help me to root my wiko view 32gb+3gb. i place fastboot oem unlock in pront comand i see waiting for device, and nothing. please creat a apk our anything for root
Would it work on k-Kool ?
We'll this sounds horrifying, just to get root permission, you have to accept to get rid of all your data and parms ? It must be another way.
I'll explain my real need for rooting my Wiko k-Kool. I bought a 64GB SD card, to be used normally as external storage, not for apps install. However I want to be able to backup my phone onto that card, just in case. I use Helium to backup my data without needing root (uses internally adb) ! However non-rooted Helium as a 3d party application has no permission to write to the SD card ! The reason I want to root is just to give Helium the permission to wirte into a backup directory.
Therefore I dont want to put my data at risk just to get root permission, but found no other way to change heliums permissions.
Thanks for any help.
This can work for the Wiko view 2 ? I can't find anything for my phone [emoji24]
Envoyé de mon W_C800 en utilisant Tapatalk
Can this work for view 2?
This work forse Wiko view max?
nothing for wiko view go?
Hello
Is there anyone who did root the wiko view go hier please?