Hey guys
wiping a stock P9000 on Ubuntu 18.04 with the SP flash tool using the 20160315 ROM and she's dead. Complete brick, no connection log on usb and no response to buttons. Doesn't power up on plug in. Removing the battery does nothing.
Any ideas or is she dead for good?
Monkey Bum 1 said:
Hey guys
wiping a stock P9000 on Ubuntu 18.04 with the SP flash tool using the 20160315 ROM and she's dead. Complete brick, no connection log on usb and no response to buttons. Doesn't power up on plug in. Removing the battery does nothing.
Any ideas or is she dead for good?
Click to expand...
Click to collapse
Vol+ while flashing, it should detect the phone and start flashing
Ruben Craveiro said:
Vol+ while flashing, it should detect the phone and start flashing
Click to expand...
Click to collapse
Thanks man!
So only kinda helped, she's "responcive"? SP flash picked up on the phone but it blew an error trying to flash, guess there's something wrong with the RAM... this went way more over my head then I was hoping...
Gave me "ERROR : STATUS_EXT_RAM_EXCEPTION (-1073414139) , MSP ERROE CODE : 0x00"
Here's the log on standard ouput:
[email protected]:~/Downloads/SP_Flash_Tool_v5.1744_Linux$ ./flash_tool.sh
QGtkStyle was unable to detect the current GTK+ theme.
QMetaObject::connectSlotsByName: No matching signal for on_pushButton_browser_clicked()
QThread::setPriority: Cannot set priority, thread is not running
"05-09-2018"
QObject::moveToThread: Cannot move objects with a parent
Connecting to BROM...
Scanning USB port...
Search usb, timeout set as 3600000 ms
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2
[email protected]/module/cdc_acm
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/tty/ttyACM0
vid is 0e8d
device vid = 0e8d
pid is 0003
device pid = 0003
com portName is: /dev/ttyACM0
Total wait time = -1528518421.000000
USB port is obtained. path name(/dev/ttyACM0), port name(/dev/ttyACM0)
USB port detected: /dev/ttyACM0
BROM connected
Downloading & Connecting to DA...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Failed to Connect DA: STATUS_EXT_RAM_EXCEPTION
Disconnect!
BROM Exception! ( ERROR : STATUS_EXT_RAM_EXCEPTION (-1073414139) , MSP ERROE CODE : 0x00.
[HINT]:
)((ConnectDA,../../../flashtool/Conn/Connection.cpp,131))
Monkey Bum 1 said:
Thanks man!
So only kinda helped, she's "responcive"? SP flash picked up on the phone but it blew an error trying to flash, guess there's something wrong with the RAM... this went way more over my head then I was hoping...
Gave me "ERROR : STATUS_EXT_RAM_EXCEPTION (-1073414139) , MSP ERROE CODE : 0x00"
Here's the log on standard ouput:
[email protected]:~/Downloads/SP_Flash_Tool_v5.1744_Linux$ ./flash_tool.sh
QGtkStyle was unable to detect the current GTK+ theme.
QMetaObject::connectSlotsByName: No matching signal for on_pushButton_browser_clicked()
QThread::setPriority: Cannot set priority, thread is not running
"05-09-2018"
QObject::moveToThread: Cannot move objects with a parent
Connecting to BROM...
Scanning USB port...
Search usb, timeout set as 3600000 ms
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2
[email protected]/module/cdc_acm
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1
[email protected]/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/tty/ttyACM0
vid is 0e8d
device vid = 0e8d
pid is 0003
device pid = 0003
com portName is: /dev/ttyACM0
Total wait time = -1528518421.000000
USB port is obtained. path name(/dev/ttyACM0), port name(/dev/ttyACM0)
USB port detected: /dev/ttyACM0
BROM connected
Downloading & Connecting to DA...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Failed to Connect DA: STATUS_EXT_RAM_EXCEPTION
Disconnect!
BROM Exception! ( ERROR : STATUS_EXT_RAM_EXCEPTION (-1073414139) , MSP ERROE CODE : 0x00.
[HINT]:
)((ConnectDA,../../../flashtool/Conn/Connection.cpp,131))
Click to expand...
Click to collapse
Try to flash on a windows pc, it avoids some errors such as this one.. It should detect easily if everything is well installed and should flash with no issues, from my own experience with sp flash tool, i find that i have way less issues when using it on Windows instead of linux..
Ruben Craveiro said:
Try to flash on a windows pc, it avoids some errors such as this one.. It should detect easily if everything is well installed and should flash with no issues, from my own experience with sp flash tool, i find that i have way less issues when using it on Windows instead of linux..
Click to expand...
Click to collapse
Had nothing to do with the Linux version, the scatterfile was wrong for me, put on the 20170904 official build from the elephone.hk forums, that scatter loaded properly and then the phone started responding to the writes. Could be because I'm Canadian, builds for me may turn out to be different than what's typical for the EU?
Try flashing 810's stock rom for me at this point you discribe had ever be my guardian for farer rom decision
---------- Post added at 11:40 PM ---------- Previous post was at 11:40 PM ----------
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Thanks Bro <3
Sammar Prince said:
Thanks Bro <3
Click to expand...
Click to collapse
No problem
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Help sir, how to fix this error? Thanks
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Help sir, how to fix this error? Thanks
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
Hi thank you i was succesfuly installed this rom and now what to restore IMEI? AT commands not working it says +CME ERROR: 100
thank you in advice i was tryed a lot of forms and i cant make calls, only 4G and SMS, restricted calls
yoalcuadrao said:
thank you in advice i was tryed a lot of forms and i cant make calls, only 4G and SMS, restricted calls
Click to expand...
Click to collapse
don't restore the imei 1 of the phone and put your sim in slot 2, might work now
willkurt27 said:
Help sir, how to fix this error? Thanks
Click to expand...
Click to collapse
did you properly install the mtk drivers ???
Well i hope i would be finally able to unbrick my phone with this... No recovery and fastoboot and by far everything works my device is recognized as mtk device but cannot flash any stock rom with SM Flash Tool
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Requirements:
- SP flash tool and right DA file (provided in the post).
-brom bypass (also provided).
-patience and perseverance.
Steps to install:
1)steps to install brom bypass:
-first install python 3 (check on google)
- then run this code in a cmd
Code:
pip install pyusb pyserial json5
-after that make sure to have all the mediatek drivers installed and install libusb from the archive i provided
- after installing libusb you will be greeted by a filter wizard window, check the "install new device filter" then connect the phone to the pc while pressing (volume +, volume - and power button) all at the same time you
will see in the list a new mtk com port appear click on it and then on install, done with the prep'.
2)steps to flash:
-first launch the brom bypass, a window will appear saying 'waiting for bootrom' connect your phone while pressing (volume +, volume - and power button) all together then you will see on the command prompt 'protection disabled' it means you have successfully bypassed the brom.
- now oppen up sp flash tool, select the download agent, select the scatter fille from the rom folder and the auth file (provided with sp flash tool archive on the post) then setup sp flash tool in uart mode with a bud rate of 921600 then flash in format all.
-done.
Hope this helped, cheers !
Click to expand...
Click to collapse
thank very much bro
muito obrigado, tive que usar o META modem para escrever IMEI. so deu certo com essa room, deus te abençoe. BRASIL
----------
MOD EDIT: English Translation Below
thank you very much, had to use META modem to write IMEI. it just worked out with this room, god bless you. BRAZIL
tiagoql said:
muito obrigado, tive que usar o META modem para escrever IMEI. so deu certo com essa room, deus te abençoe. BRASIL
Click to expand...
Click to collapse
in english or indonesia please
hello if I flash this rom to my miui 12.5.1 will this work? or my phone will be stucked in bootloop? sorry im newbie
work.
only write imei simcard 2 brother
razers211 said:
after further testing and finally restoring my IMEIs using this rom, i can say that it is indeed working, so hope it helps a lot of you guys stuck with a phone without IMEIs.
link :
Xiaomi Redmi 9 ENG Firmware (Engineering Rom)
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Click to expand...
Click to collapse
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
What am I doing wrong?
hckbkl said:
work.
only write imei simcard 2 brother
Click to expand...
Click to collapse
which da will i use? DA_6765_6785_6768_6873_6885_6853 or MTK_AllInOne_DA for redmi 9 mt6768
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
try to insert the auth file
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
or install mtk drivers properly
lobothefoots said:
Hello and thanks for sharing, I have the same error as @willkurt27
while using SPFlash Tool
What I do:
Launch bypass.bat
Plug my phone with vol - pressed and battery unplugged.
[2021-08-24 21:33:09.958798] Waiting for device
[2021-08-24 21:39:08.793257] Found device = 0e8d:0003
[2021-08-24 21:39:14.833772] Device hw code: 0x707
[2021-08-24 21:39:14.833772] Device hw sub code: 0x8a00
[2021-08-24 21:39:14.833772] Device hw version: 0xca00
[2021-08-24 21:39:14.833772] Device sw version: 0x0
[2021-08-24 21:39:14.833772] Device secure boot: True
[2021-08-24 21:39:14.833772] Device serial link authorization: True
[2021-08-24 21:39:14.833772] Device download agent authorization: True
[2021-08-24 21:39:14.833772] Disabling watchdog timer
[2021-08-24 21:39:14.849712] Disabling protection
[2021-08-24 21:39:14.849712] Using kamakiri
[2021-08-24 21:39:14.849712] Protection disabled
Appuyez sur une touche pour continuer...
Then I use SPFlash Tool v5.1924.0
Tried with DA_6765_6785_6768_6873_6885_6853.bin and MTK_AllInOne_DA.bin
View attachment 5392951
What am I doing wrong?
Click to expand...
Click to collapse
use mtkbypass