I havea Hipstreet Titan HS-7TB4-4BNDL with WiFi 7" Touchscreen Tablet PC
I uninstall/installed some apps from the tablet like (app installer,Sitting,System UI ,Packet installer,Etc) and the next Boot when I turned it on, it quitted booting and the screen froze with the HIP-STREET still in the center of the screen than going blank.
I had tried a lot of ways to make it boot again including hard power off (pressing the power button for more than 5 seconds), reset the device (pushing a small pin to the small hole at the side of the screen, there are 2 holes: one for microphone and the other for reset button,try to press combinations of various keys I can find on the tablet pc. They all failed to fix this
Can Somebody help me or guide me to bring back my hipstreet tablet back to the original state.
Thanking You.
kmubarak said:
I havea Hipstreet Titan HS-7TB4-4BNDL with WiFi 7" Touchscreen Tablet PC
I uninstall/installed some apps from the tablet like (app installer,Sitting,System UI ,Packet installer,Etc) and the next Boot when I turned it on, it quitted booting and the screen froze with the HIP-STREET still in the center of the screen than going blank.
I had tried a lot of ways to make it boot again including hard power off (pressing the power button for more than 5 seconds), reset the device (pushing a small pin to the small hole at the side of the screen, there are 2 holes: one for microphone and the other for reset button,try to press combinations of various keys I can find on the tablet pc. They all failed to fix this
Can Somebody help me or guide me to bring back my hipstreet tablet back to the original state.
Thanking You.
Click to expand...
Click to collapse
Any luck with resolving this?
I've got a Chinese tablet that boots properly up to the unlock screen, where if I'm quick I can unlock, I can see wifi is connected, etc. but around that point it completely freeze, even the power button doesn't turn off the creen and I have to reset it by long pressing the power button.
I tried all combinations of keys to bring up a recovery (power + volumes) without luck so far. If I press any volume or back key while powering up, the tablet doesn't power up and stays black. adb isn't finding the tablet. I opened the tablet, there are pins to connect a rx/tx serial. I could do connect a serial adapter to it if that could be of any help.
Actually, at this point I don't care much about the tablet but that could be a good opportunity to start learning a bit more about Android hardware development, just don't know exactly where to start.
Any tip?
3 weeks ago I finally spent the $20.00 and replaced the defected battery in my Sanei N78 tablet. During the week that followed I had no trouble that is till a week later.
After using my Tablet till the battery ran down and shut it self off I plugged it in to recharge. This time however, instead of getting the Android opening screen, I got nothing. So I pressed the power button till the Sanei's logo spinning color wheel page appeared. But, instead of continuing booting on in to the Android opening screen, it just stayed stuck on that spinning color wheel.
Since this has happen to me before I proceeded to use what I call the reset command (pressing the power and up volume buttons simultaneously).
Yet, instead of giving me a choice to reset or not, all I got the Android logo laying on its back with its access panel open and an exclamation point in a red triangle. Which after a few minutes returns to the spinning color wheel page?
I keep trying difference combinations of the power/volume up/volume down buttons; however, all I get is the "dead" Android logo or the spinning color wheel.
I have also tried disconnected the battery and let the Tablet sit unpowered for the next 48 hours - It didn't work:crying:
What has gone wrong?
Has the “drive” containing the Android operation system failed? Has Android itself become corrupted? Is there a fix?
When I asked this question to a site that sell only Sanei tablets I was told to hold the power button for 5 to 10 seconds. Well, I have and nothing changes. I was also informed that another answer is to reinstall the firmware.
As for the latter, I would like to try, but, the only way I could is to download it to a thumb drive from the computer I am using to post this message and either run it off that or use my home Win98 OS computer (BTW: I have connected the tablet to my home computer and while 2 drive icons do appear in My Computer any attemp to open them give me a "drive not ready" message. This because this public computer that I am using will not premit under any cirsumstances a tablet to be connected to it
Is this possible?
If not, then I have another paperweight for my desk
Hi,
My Zenithink c93 decided not to boot. It gets stuck at the android logo with three horizontal white lines above it going across the screen as soon as I turn it on. I've tried pretty much every button combination (power, back, vol up and vol down), but it didn't work. The only combo that gives a different result is power button + back, which shows the android logo with the words "Upgrading" directly beneath it, then turns off after about 2 seconds. I can't even get into the recovery menu so I'm really stuck. Also, the tablet is not rooted.
Things I've tried:
Wait at the android logo screen for 15 minutes.
Desolder the battery for 10 seconds and solder it back again.
Copy zt-update.zip to the micro-SD card and tried doing the upgrading process.
They all did not solve the problem. How do I fix this?
anyone?!!!
So i just got a ul40 phone [dont laugh] and i went in and changed settings, i disabled apps because i was getting like three hors on the batt.
now the phone starts to boot with a white ANS bootscreen then it goes into a second screen, blue that says virgin mobile and thats it.
it stays blue, cant shut the phone off
screen remains on for an hour wont change nothing ive tried helps
CAN ANYONE HELP
by the way i have a laptop running windows 10 home
CAN I FIND DRIVERS TO USE LAPTOP TO GET IN TO THE PHONE????
Reset the Phone
You need to do a factory reset. Hold volume 'up' button and power button at same time for a minute or so, then choose factory reset.
rjm831 said:
You need to do a factory reset. Hold volume 'up' button and power button at same time for a minute or so, then choose factory reset.
Click to expand...
Click to collapse
no effect pwr button does nothing, batt full all external buttons inop. Blank screen
---------- Post added at 05:07 AM ---------- Previous post was at 05:02 AM ----------
FLASHNORM7 said:
So i just got a ul40 phone [dont laugh] and i went in and changed settings, i disabled apps because i was getting like three hors on the batt.
now the phone starts to boot with a white ANS bootscreen then it goes into a second screen, blue that says virgin mobile and thats it.
it stays blue, cant shut the phone off
screen remains on for an hour wont change nothing ive tried helps
CAN ANYONE HELP
by the way i have a laptop running windows 10 home
CAN I FIND DRIVERS TO USE LAPTOP TO GET IN TO THE PHONE????
Click to expand...
Click to collapse
Same problem
RodamusPrime said:
no effect pwr button does nothing, batt full all external buttons inop. Blank screen
---------- Post added at 05:07 AM ---------- Previous post was at 05:02 AM ----------
Same problem
Click to expand...
Click to collapse
The battery is taped into the case with double-sided tape - in other words, very gently pry the battery out (from bottom of battery) & leave it out for a minute or two. Then put it back in & try again.
Fixes for the Boot Loop/Frozen ANS UL40
American Network Solutions (ANS) mobile phones provided by Assurance Wireless (Virgin Mobile) have been known to boot loop, freeze, stay frozen, crash, (right out of the box, brand new) and worse there is inaccurate or completely wrong information on how to do a factory reset and reboot the device. Below I will outline how to reboot the phone and perform a hard factory-reset with no home button on this cellphone.
Problem: Phone won’t turn off, won’t restart, or is stuck on and has no removable battery.
Solution: Keep the phone on and unplugged until battery dies or perform a hard reboot (see below).
Problem: My cell-phone is stuck on and there is no home button to do a hard reset
Solution: Perform a hard reboot. To restart a phone without taking out the battery, simply hold the Volume Up button, the home button (do not press if there is none obviously) and the Power button at the same time. While you hold these simultaneously, the phone will reboot in about 5 to 10 seconds.
Problem: I can’t factory reset my ANS UL40 phone (American Network Solutions) from Assurance Wireless by Virgin Mobile because I can’t get into the recovery menu.
Solution: Turn the phone off (or do a hard reset by holding the Volume-Up Button and the On-Button. Phones with no home button all reboot like this so just wait a few moments and the phone will restart.
Problem: My new mobile phone from Assurance Wireless gets stuck on the loading screen!
Solution: Perform a hard reboot (Volume Up + Power) then when it restarts and you’re on the white Assurance Wireless screen, stop holding power and only hold Volume Up. Keep pressing-and-holding the Increase Volume button and after a while you will be navigated to the Factory Reset Menu. You can wipe the cache partition only or perform a factory reset (which will also wipe the cache). To move around on the menu, use the volume keys (increase volume goes up, decrease volume goes down) and to select your entry simply use the power button (the on button). If this still doesn’t work, see further instructions in the solutions below.
Problem: Phone is frozen on loading screen, stuck in boot-loop even after factory reset/wiping cache partition.
Solution: After you have factory reset or wiped the cache partition you can also choose to install an update from the internal memory or sd-card. If you select this option it will perform a more rigorous factory reset then since you won’t have a package to install it will cancel. I’ve noticed my device getting out of the boot loop once I did this process and it was stuck on the boot screen even after I did a factory reset.
Problem: Can’t get to the recovery menu with my government assistance phone.
Solution: Turn off the phone and with the volume up button held down, power the device on. Keep holding both buttons until you see the white “American Network Solutions” screen with the outline of an eagle. At this point release the power button and continue to hold the volume-up key. After about 5 seconds you will now be inside the Recovery Menu and can do a factory reset.
Problem: My phone has no home button and I need to hard reboot to get to the Recovery Menu and perform a factory reset!
Solution: Hold the Volume-Up Button and the Power Button at the same time. for at least 10 seconds. Your device will restart and after the white ANS screen shows, stop holding the power button. Continue holding the increase audio key until you are at the Factory Reset / Recovery Menu screen. Use the volume buttons to navigate the menu and use the on button to select your choice.
Problem: My phone hangs on the blue Assurance Wireless screen.
Solution: See Above.
Even on the Virgin Mobile and Assurance Wireless websites and in the owner’s manual it says to hold the Volume Up + Home Button + Power Key and to keep holding them until you’re in Recovery Menu. This isn’t going to work for two reasons on the UL40: 1) It has no home button! and 2) it will just keep rebooting every 5 seconds if you hold the power button down constantly. You have to hold the Volume-Up Button and the Power Button until the phone reboots and then let go of the power button while still holding the volume up button. Keep holding the volume up key until you’re into Recovery Mode.
I hope this helps as the information online is either incomplete or completely wrong. Some places say to keep holding the power button along with the volume up key and if you do that the device will just keep restarting, effectively creating a boot loop where there wasn’t any before. Genius! lol. I figured this out after my device, fresh out of the box, froze while charging on the blue Assurance Wireless screen. Finally OCD is good for something! These phones are supposed to be a “Lifeline” but I’d be hard-pressed to get ANYTHING on the line with this potato. Avoid at all costs unless absolutely necessary.
Enjoy. :highfive:
Magic Plants said:
American Network Solutions (ANS) mobile phones provided by Assurance Wireless (Virgin Mobile) have been known to boot loop, freeze, stay frozen, crash, (right out of the box, brand new) and worse there is inaccurate or completely wrong information on how to do a factory reset and reboot the device. Below I will outline how to reboot the phone and perform a hard factory-reset with no home button on this cellphone.
Problem: Phone won’t turn off, won’t restart, or is stuck on and has no removable battery.
Solution: Keep the phone on and unplugged until battery dies or perform a hard reboot (see below).
Problem: My cell-phone is stuck on and there is no home button to do a hard reset
Solution: Perform a hard reboot. To restart a phone without taking out the battery, simply hold the Volume Up button, the home button (do not press if there is none obviously) and the Power button at the same time. While you hold these simultaneously, the phone will reboot in about 5 to 10 seconds.
Problem: I can’t factory reset my ANS UL40 phone (American Network Solutions) from Assurance Wireless by Virgin Mobile because I can’t get into the recovery menu.
Solution: Turn the phone off (or do a hard reset by holding the Volume-Up Button and the On-Button. Phones with no home button all reboot like this so just wait a few moments and the phone will restart.
Problem: My new mobile phone from Assurance Wireless gets stuck on the loading screen!
Solution: Perform a hard reboot (Volume Up + Power) then when it restarts and you’re on the white Assurance Wireless screen, stop holding power and only hold Volume Up. Keep pressing-and-holding the Increase Volume button and after a while you will be navigated to the Factory Reset Menu. You can wipe the cache partition only or perform a factory reset (which will also wipe the cache). To move around on the menu, use the volume keys (increase volume goes up, decrease volume goes down) and to select your entry simply use the power button (the on button). If this still doesn’t work, see further instructions in the solutions below.
Problem: Phone is frozen on loading screen, stuck in boot-loop even after factory reset/wiping cache partition.
Solution: After you have factory reset or wiped the cache partition you can also choose to install an update from the internal memory or sd-card. If you select this option it will perform a more rigorous factory reset then since you won’t have a package to install it will cancel. I’ve noticed my device getting out of the boot loop once I did this process and it was stuck on the boot screen even after I did a factory reset.
Problem: Can’t get to the recovery menu with my government assistance phone.
Solution: Turn off the phone and with the volume up button held down, power the device on. Keep holding both buttons until you see the white “American Network Solutions” screen with the outline of an eagle. At this point release the power button and continue to hold the volume-up key. After about 5 seconds you will now be inside the Recovery Menu and can do a factory reset.
Problem: My phone has no home button and I need to hard reboot to get to the Recovery Menu and perform a factory reset!
Solution: Hold the Volume-Up Button and the Power Button at the same time. for at least 10 seconds. Your device will restart and after the white ANS screen shows, stop holding the power button. Continue holding the increase audio key until you are at the Factory Reset / Recovery Menu screen. Use the volume buttons to navigate the menu and use the on button to select your choice.
Problem: My phone hangs on the blue Assurance Wireless screen.
Solution: See Above.
Even on the Virgin Mobile and Assurance Wireless websites and in the owner’s manual it says to hold the Volume Up + Home Button + Power Key and to keep holding them until you’re in Recovery Menu. This isn’t going to work for two reasons on the UL40: 1) It has no home button! and 2) it will just keep rebooting every 5 seconds if you hold the power button down constantly. You have to hold the Volume-Up Button and the Power Button until the phone reboots and then let go of the power button while still holding the volume up button. Keep holding the volume up key until you’re into Recovery Mode.
I hope this helps as the information online is either incomplete or completely wrong. Some places say to keep holding the power button along with the volume up key and if you do that the device will just keep restarting, effectively creating a boot loop where there wasn’t any before. Genius! lol. I figured this out after my device, fresh out of the box, froze while charging on the blue Assurance Wireless screen. Finally OCD is good for something! These phones are supposed to be a “Lifeline” but I’d be hard-pressed to get ANYTHING on the line with this potato. Avoid at all costs unless absolutely necessary.
Enjoy. :highfive:
Click to expand...
Click to collapse
Great advice. Have had an ANS UL-40 for over a year, & they truly stink if you can't root them - which I can't since I've no computer access (for ADB). I honestly miss the old android Jellybean phones that could be rooted with just an app. Oh well.
I have a UL40, I tried the factory reset method, it reset but the phone is still suck on the blue assurance wireless screen.
Ps. It's been like this for days. It stays on the blue screen for about 5 minutes, then the screen is completely black. When I try to turn it on again, it's blue for five minutes then goes black.
Help...?
My ans ul40 keeps restarting. Every 2 to 5 seconds, on its own. I tried to factory reset it with the steps listed above and I can't tell if it works because when I hold the volume up and power button, it does two things, the phone will either shut off again and go into the constant restarting or number 2, it will show me a white screen as if to say the holding down of the volume and power button worked, but then it just goes back into the constant restarting... at this point I'm thinking I have to call for a new phone.
I have a ul40, technically 2 because one wouldn't hold a charge and now this one keeps crashing and giving me error codes. I can't afford to just drop money on a new phone (hence why i got this one) and I am FORCED to do a factory reset every 3-5 days because the memory gets so full, even if I erase memory, disable or delete apps and barely use it outside of texting or calling. Its frustrating to high hell. The code that shows up is either "GOOGLE SERVICES FRAME WORK KEEPS STOPPING", or "COM.ANDROID.PHONE HAS STOPPED"
Any advice is helpful advice.
Similar problem
FLASHNORM7 said:
So i just got a ul40 phone [dont laugh] and i went in and changed settings, i disabled apps because i was getting like three hors on the batt.
now the phone starts to boot with a white ANS bootscreen then it goes into a second screen, blue that says virgin mobile and thats it.
it stays blue, cant shut the phone off
screen remains on for an hour wont change nothing ive tried helps
CAN ANYONE HELP
by the way i have a laptop running windows 10 home
CAN I FIND DRIVERS TO USE LAPTOP TO GET IN TO THE PHONE????
Click to expand...
Click to collapse
i have a similar problem except it gets to the blue assurance screen and then it turns off and then reboots i can't fix it and i don't know what's wrong this is the only phone i have (don't laugh) but i can't not have this phone
Have you tried taking out the battery for a minute or two, then powering up? (Battery is only held down with tape - it can gently be pried out). The other option is a complete reset - instructions on holding the power & volume keys, etc, are posted already.
this phone seems to ship with a lot of malware factory-installed (and possibly more built into the firmware?) so it's critical to go into Settings->Apps and disable everything that looks suspicious, including the less obvious "notepad" app and "voice recorder" app. this should help your phone run somewhat better but there's some adware still running that i haven't figured out how to disable, so a perfect solution in theory would be to root the phone as discussed in this thread. unfortunately so far there doesn't seem to be a working root for this phone.
I did fatory reset from recovery until arrivet to let us go then skip sim then next as new device/retrive from cloud then lis of wifi appear and stop at this point nothing else appear to enter
what the solution please?????