Hoping to find some help here. I have searched the web and no definitive answer. I was running CM 10.1.3 on my Razr Maxx for a long while. Just flashed to CM 10.2 with Android 4.3. Since flashing, I no longer get a 4g icon for my signal, I get LTE. In addiiton, the LTE signal fades in and out and most times the bars are white which I have found out means I'm not synced with Google servers. I have played with the APN options to no avail. Is anyone familiar with this problem? Is there a fix? Thanks for any help you can provide.
cigator said:
Hoping to find some help here. I have searched the web and no definitive answer. I was running CM 10.1.3 on my Razr Maxx for a long while. Just flashed to CM 10.2 with Android 4.3. Since flashing, I no longer get a 4g icon for my signal, I get LTE. In addiiton, the LTE signal fades in and out and most times the bars are white which I have found out means I'm not synced with Google servers. I have played with the APN options to no avail. Is anyone familiar with this problem? Is there a fix? Thanks for any help you can provide.
Click to expand...
Click to collapse
The LTE icon replaced the 4G icon in development, that's normal. Are you sure you're losing sync status? Where did you read that is the reason? Do your emails, etc push through notification? If so, there's really no problem other than an icon that isn't 100% representative of its status.
Also, did you do a complete wipe before upgrading to 10.2? Major updates usually recommend full wipes before upgrading for many reasons.
I did a fresh root and install of safestrap 3.65 and CM10.2 stable on my xt912 for verizon. I also have the same issue. Coming from the stock rom I now get terrible service and if I change the network to anything with LTE (global or cdma/evdo +LTE) I cannot send or receive picture messages. I tried to change the APN and it makes no difference. Lastly if I try to edit the APN it will disappear from the list.
I stopped editting the apn because when I limit the service to cdma/evdo I can send and recieve picture messages, but I get no LTE/4g service.
I am starting to wonder if the rom slot 1 conflicts somehow with the original stock rom.
After installing safestrap I did a factory wipe (not advanced) and installed the rom and gapps.
If there is something I am missing please do inform me. Perhaps the op's issue is the same.
owenfred said:
I did a fresh root and install of safestrap 3.65 and CM10.2 stable on my xt912 for verizon. I also have the same issue. Coming from the stock rom I now get terrible service and if I change the network to anything with LTE (global or cdma/evdo +LTE) I cannot send or receive picture messages. I tried to change the APN and it makes no difference. Lastly if I try to edit the APN it will disappear from the list.
I stopped editting the apn because when I limit the service to cdma/evdo I can send and recieve picture messages, but I get no LTE/4g service.
I am starting to wonder if the rom slot 1 conflicts somehow with the original stock rom.
After installing safestrap I did a factory wipe (not advanced) and installed the rom and gapps.
If there is something I am missing please do inform me. Perhaps the op's issue is the same.
Click to expand...
Click to collapse
You need to update to kitkat stock messaging app & delete old, how to here:
http://forum.cyanogenmod.com/topic/80704-mms-not-sending-issues-editing-apn-settings/
crackerjack1957 said:
You need to update to kitkat stock messaging app & ...
Yes I did that. That is why I can send them when on cdma/evdo. It has never worked with global or any lte network.
Thinking of trying cm11m4 on rom slot 2 to see if that is better...
Click to expand...
Click to collapse
owenfred said:
crackerjack1957 said:
You need to update to kitkat stock messaging app & ...
Yes I did that. That is why I can send them when on cdma/evdo. It has never worked with global or any lte network.
Thinking of trying cm11m4 on rom slot 2 to see if that is better...
Click to expand...
Click to collapse
It worked for me & all the others that read & followed guidelines.
Click to expand...
Click to collapse
crackerjack1957 said:
owenfred said:
It worked for me & all the others that read & followed guidelines.
Click to expand...
Click to collapse
Read #15 & others
http://forum.cyanogenmod.com/topic/80704-mms-not-sending-issues-editing-apn-settings/
Setup (2) droid razrs with 8sms & Network mode on CDMA+LTE+EVDO
Global works also
Click to expand...
Click to collapse
crackerjack1957 said:
owenfred said:
It worked for me & all the others that read & followed guidelines.
Click to expand...
Click to collapse
It is fine to get mms to send on CDMA. If the phone is on a 4G or LTE antenna it doesn't work for me. Also, this does not solve the issue of the APN's disappearing. This is a fix for some cases not a solution.
In my case I created Rom slot #2 and installed CM11 M4 snapshot and all is working there. LTE works fine, MMS sends... I didn't find any immediate other issues in the 2 hrs I played with it last night. Looks like this may be the daily driver for a while until CM11 stable comes out.
I still have 10.2 available in Rom slot #1 so I can test if anyone cares to find the real "solution"
Owen
Click to expand...
Click to collapse
owenfred said:
crackerjack1957 said:
It is fine to get mms to send on CDMA. If the phone is on a 4G or LTE antenna it doesn't work for me. Also, this does not solve the issue of the APN's disappearing. This is a fix for some cases not a solution.
In my case I created Rom slot #2 and installed CM11 M4 snapshot and all is working there. LTE works fine, MMS sends... I didn't find any immediate other issues in the 2 hrs I played with it last night. Looks like this may be the daily driver for a while until CM11 stable comes out.
I still have 10.2 available in Rom slot #1 so I can test if anyone cares to find the real "solution"
Owen
Click to expand...
Click to collapse
I would not have thought this would be an issue on a stable build either.
With kitkat in development, CM10.2 will be abandoned.
Probably will try CM11 nightly myself in about a month unless there is another snapshot or even stable build by then.
Click to expand...
Click to collapse
Related
Hi all,
I've posted a couple times before on getting the wifi working on stock Moto android for the photon, I cannot reply on the dev forum discussing this cm9 rom as I'm allegedly less than 10 posts or something.
Each time I boot up with aeroplane mode off (so all network stuff is on) com.android.phone crashes and I just have to press ok, it happens again each time I enable then disable aeroplane mode or type *#*#4636#*#* and turn off then on the radio.
I cannot get any mobile connection, I think the radio cannot turn on as the GSM service is "radio off".
Any ideas on how I should troubleshoot, I think loads of people have the issue but the recommended fix does not work for me (and others).
The recommended fix is to edit /system/build.prop and change ro.telephony.default_network from 7 to 0 and this does not work for me (editing it with root explorer).
I understand that it changes the network type to WCDMA prefered (I think that is another name for UMTS). One can also change the prefered network using the above code in the dialer and scrolling down to just above the button to turn the radio off/on.
Any ideas?
Update:
Sorry for taking ages to reply, seems like most people using the mopho are on Sprint using CDMA and so don't have issues, I'm in Australia on Vodafone so use GSM(2G)/WCDMA (3G).
I got this working ages ago and after a few version changes, I'm now on beta 0.4.5.1 as camera would freeze after taking a picture (including freezing the camera system so face unlock stopped) on beta 0.4.4.
Yes, reflashing rom after editing ro.telephony.default_network to 0 does fix it, but one does not have to reflash, just reboot into recovery and do factory reset other basics may work, though I tried cache, dalvik cache and permission fix, that did not seem to fix it for me. I think factory reset in recovery formats: data, cache, ext-sd/android....something file and one or 2 other things.
I think formatting data gets rid of all your settings, maybe one does not need the data reformat, I wonder if the android file on the SD card has certain settings with the RIL.
When you are having the GSM issue and no signal, under the more menu which is under wireless & networks, there is no "mobile networks" option and when dialling *#*#info#*#* (4636) under phone information, I think GSM service says "radio off".
Yes, after I did make a post, it did say 4 posts and then I actually knew I how many I had done, I was unsure as I had posted quite a lot about the early wifi issues when Spring crippled the original rom but I was also posting in the Moto owners forum and could not remember how many posts I had done in this forum.
Any way, will update if I think there is anything else useful to add/ask. I just love the openness of Android, especially compared to the iPhone, its just so great that someone may download the source and port it to a device such as what Joker and the others helping him out did, so now we have ICS on a very powerful and capable device. As much as Jobs may have had all sorts of issues with similarities between Android and iOS, we have more use from it and "like" google better from it (without spending crap loads of money on one of like only 2 devices available, we just have soooo much choice;-)
Fisher
Ok, so I understand that editing the file line above (/system/builld.prop , line ro.telephony.....) to 0 instead of 7 sets the network as WCDMA prefered (it even says so in the file just above the line you edit).
When dialing *#*#4636#*#*, I see GSM auto (PRL) instead of WCDMA prefered even after reboot.
It seems that the system is not reading that part of the build.prop file or its being over ridden by something else, how can I troubleshoot?
It stays on GSM auto (PRL) even if I change it in the dialer, exit and then type the code back into the dialer.
Have you tried relishing from scratch? & start from cm9 0.1.0 2d not 0.2.0 . I say that because when I first tried cm9 I started from cm9 0.2.0 and I had lots of problems and battery drains fast but then I clean everything off and redone it from cm9 0.1.0 2d note everything is working like it should even better . Hope you getting going...
Sent from my MB855 using Tapatalk
If I remember what was said in the cm9 thread you have to edit build.prop from the zip, and then flash, not edit after flash or it doesn't work.
I'm a MoPho-in Martian
Cm9 v2 is running great on my photon
Sent from my MB855 using Tapatalk
partycove said:
Cm9 v2 is running great on my photon
Click to expand...
Click to collapse
Same here!
fisher.grubb said:
Hi all,
I've posted a couple times before on getting the wifi working on stock Moto android for the photon, I cannot reply on the dev forum discussing this cm9 rom as I'm allegedly less than 10 posts or something.
Click to expand...
Click to collapse
Sounds like the other guys have you helped with the FC portion, but nobody has addressed the first complaint. You're currently showing as having 5 posts to me when I look at your profile, so it's not alleged you're under 10 posts, you are under 10 posts. The word "allegedly" implies you disagree with that post count and if so, I'd suggest contacting an admin to have it looked into. I don't spend too much time on XDA so unfortunately I don't know who (specifically) to suggest you contact.
Hope you get it all sorted out! Cheers!
post count
ya the to little post count thing is semi wack. i understand why its there, but i deff still feel you pain. I have been a avid reader of most everything mopho related since about October, but am not much of a poster until not i guess
voicemail
I have ics on my mopho but Im not getting any voicemails. When I get a call and it goes to voicemail i receive a text that says I have received a voicemail and to call a weird number. When I do sometimes it asks me if I have a new phone with voicemail and sometimes its just a busy tone. Is anyone else having this problem?
FernBch said:
If I remember what was said in the cm9 thread you have to edit build.prop from the zip, and then flash, not edit after flash or it doesn't work.
I'm a MoPho-in Martian
Click to expand...
Click to collapse
How do you edit files in the zip? Im trying to replace the APNS file but i cant delete the old one. When I unzip it, replace the file, then rezip it, the file fails to flash. Any suggestions?
---------- Post added at 02:43 PM ---------- Previous post was at 02:42 PM ----------
ChadH42 said:
Same here!
Click to expand...
Click to collapse
Did you have to fix MMS on yours. I've tried the fixes but I still can't get it working.
partycove said:
Cm9 v2 is running great on my photon
Sent from my MB855 using Tapatalk
Click to expand...
Click to collapse
How is the battery life compared to 2.3.4?
cm9 ics beta 2 memory bug
I just flashed my epic to cm9 beta 2 and its been workin fine all day and now I'm getting error messages about it being "low on memory". Is there a fix for this??
tengengegas said:
I just flashed my epic to cm9 beta 2 and its been workin fine all day and now I'm getting error messages about it being "low on memory". Is there a fix for this??
Click to expand...
Click to collapse
Why would you ask that in a Photon forum?
I bought my Evo4G LTE about two weeks ago and immediately rooted it. I have S-off with lazy panda and am running CM10 JB rom. Throughout the first week everything was running just fine. I could send and receive picture messages and MMS using both 3G and wifi. However over the past few days this has all changed. Whenever a picture comes in, either on 3G or wifi, the word "downloading" appears greyed out but the message never comes in. I have turned off and back on then back off automatic downloads. I have rebooted the phone, reloaded an earlier nandroid and nothing works. This happened all the time on my OG Evo 4G and I just wrote it off to "being the way it is". But honestly that isn't good enough with a brand new phone. I tried researching this and came up with someone saying to connect to Sprint Zone, which I cannot do because it is a stock app only and let the program troubleshoot for me. I downloaded an apk of this but it will not work.
If anyone has any help with this it would be much appreciated.
Have you tried updating ur profile and prl? I do that anytime and everytime I flash a new rom.....just a thought
vel7wil said:
Have you tried updating ur profile and prl? I do that anytime and everytime I flash a new rom.....just a thought
Click to expand...
Click to collapse
Profile and prl?
rersland613 said:
Profile and prl?
Click to expand...
Click to collapse
settings/system updates update both
bigdaddy619 said:
settings/system updates update both
Click to expand...
Click to collapse
I don't have a system updates tab on my settings drop down? Maybe I'm in the wrong spot?
rersland613 said:
I don't have a system updates tab on my settings drop down? Maybe I'm in the wrong spot?
Click to expand...
Click to collapse
you are looking in quick settings there is a settings icon in the upper right of the screen in the pull down on the notifications side
bigdaddy619 said:
you are looking in quick settings there is a settings icon in the upper right of the screen in the pull down on the notifications side
Click to expand...
Click to collapse
I did that. It is divided into 6 main sections: wireless and networks, interface, device, personal, accounts, and system. But I can't find anything about system updates. Again I am running CM10 Jelly Bean.
rersland613 said:
I did that. It is divided into 6 main sections: wireless and networks, interface, device, personal, accounts, and system. But I can't find anything about system updates. Again I am running CM10 Jelly Bean.
Click to expand...
Click to collapse
it's been a while since i've been on CM try looking in system
You need a sense Rom to update profile and prl
PHP:
om4 said:
You need a sense Rom to update profile and prl
Click to expand...
Click to collapse
Which sense rom do you suggest? So I need to keep one for backup on my phone and switch back over to CM10 after I update? I've only been getting one bar of cell service lately. Is this all pointing to the same issue? Would the prl still be the problem even when on wifi?
Any sense Rom, since its just for updates grab on of the basic stock roms from android development section. All the custom roms are a lot larger due to the various mods and extra stuff
om4 said:
Any sense Rom, since its just for updates grab on of the basic stock roms from android development section. All the custom roms are a lot larger due to the various mods and extra stuff
Click to expand...
Click to collapse
Went ahead and downloaded the stock rom with goodies. Went through settings and updated the prl and profile. Can anyone tell me what the correct prl should be or does it depend on your location? Btw thank you for helping me with this.
Mine is at 25006
I'm on the same prl then. I still don't know what's up. I always have 1 bar of signal and am very frequently on 1x instead of 3g. At the same time my wife will be on 3g with full bars on her iPhone. The part that gets me about not sending and receiving pictures is that I was on WiFi. Should it matter what profile and prl I'm on if I'm trying to receive data via WiFi?
Sent from my EVO using xda app-developers app
Well most ASOP roms have the issue of intermittent mms not downloading but with that said some sense roms don't allow mms over WIFI and some do. If you aren't connected to WIFI and you still can't download mms after profile and prl updates you can get your msl number and do a data reset and go through the process of reregistering your phone with sprints network and that should solve your issue.
Sent from my EVO using Tapatalk 2
Hey guys, i have straight talk with all apn settings on and 4g working however, this has to be the most difficult time I have EVER had with a phone. The service constantly goes in and out even with all bars present at times. These are the problems i have:
1. When wcdma and 4g is enabled, calls to others take long to start and state "conditional call forwarding active". Sometimes I cannot answer calls because it scrambles and makes crazy sounds.
2. When gsm is enabled with edge, everything seems to work fine with no issues. "Conditional call forwarding active" never appears
I have tried the following modems and none seem to fix the issues in terms of full 4g service and a working phone
Kid test modem - Blaze modem (tmobile)
UCLF6 alone and embedded in the UCLF6BS rom
Ucle2 modem
Uclf5 modem
Goldie b5 rom
None of these radios/modems seem to fix the issues, if they do, sometimes its temporary. There are no outages in my area, is Straight talk service really bad, or is it the phone??? I just dont get it.. Am I flashing wrong? I have been flashing with TWRP and have not used CMW since. I flash the modem then clear cache and dalvik. Am I missing something?? Please help, thanks so much
Im running Blackstar 8 no added on modem radio or nothing the problem your having is in the apn settings your using go in change proxy to not set .remove port #.and add authentication pap or chap keep your
mms proxy the same let me know how you make out
Agreed .....
APN issues are "very " likely the cause of your issues ...g
Hey guys, thanks so much for the response. So far I am still getting the "Conditional call forwarding active" popup right when the call starts. I will be able to give it a test run in Manhattan to see if I get the issues I had before. Thanks so much guys, will keep you updated
gregsarg said:
Agreed .....
APN issues are "very " likely the cause of your issues ...g
Click to expand...
Click to collapse
jxs714 said:
Hey guys, i have straight talk with all apn settings on and 4g working however, this has to be the most difficult time I have EVER had with a phone. The service constantly goes in and out even with all bars present at times. These are the problems i have:
1. When wcdma and 4g is enabled, calls to others take long to start and state "conditional call forwarding active". Sometimes I cannot answer calls because it scrambles and makes crazy sounds.
2. When gsm is enabled with edge, everything seems to work fine with no issues. "Conditional call forwarding active" never appears
I have tried the following modems and none seem to fix the issues in terms of full 4g service and a working phone
Kid test modem - Blaze modem (tmobile)
UCLF6 alone and embedded in the UCLF6BS rom
Ucle2 modem
Uclf5 modem
Goldie b5 rom
None of these radios/modems seem to fix the issues, if they do, sometimes its temporary. There are no outages in my area, is Straight talk service really bad, or is it the phone??? I just dont get it.. Am I flashing wrong? I have been flashing with TWRP and have not used CMW since. I flash the modem then clear cache and dalvik. Am I missing something?? Please help, thanks so much
Click to expand...
Click to collapse
hey man I'm also in NY on straight talk...I'm on long island and I have never experienced what you are going through .I have tried all diff roms and modems.. only difficult problem I had was no mms .that is until I just edited the apn
- GNote via Tapatalk 2
[QUO=nycokla;32963297]hey man I'm also in NY on straight talk...I'm on long island and I have never experienced what you are going through .I have tried all diff roms and modems.. only difficult problem I had was no mms .that is until I just edited the apn
- GNote via Tapatalk 2[/QUOTE]
Really? I'm still having issues. Should I try flashing with cwm instead Of twrp?? I tried what you guys said above and still no good. Man this sucks!!
jxs714 said:
[QUO=nycokla;32963297]hey man I'm also in NY on straight talk...I'm on long island and I have never experienced what you are going through .I have tried all diff roms and modems.. only difficult problem I had was no mms .that is until I just edited the apn
- GNote via Tapatalk 2
Click to expand...
Click to collapse
Really? I'm still having issues. Should I try flashing with cwm instead Of twrp?? I tried what you guys said above and still no good. Man this sucks!![/QUOTE]
I would start by using twrp,wipe everything 3 times...and just install the Rom of choice..I'm using padawan v3..then just installed the newest modem...then restart and let it sit for 10 min...if you still have problems then check your apn.if still not working call straight talk and have them reset your account
- GNote via Tapatalk 2
nycokla said:
Really? I'm still having issues. Should I try flashing with cwm instead Of twrp?? I tried what you guys said above and still no good. Man this sucks!!
Click to expand...
Click to collapse
I would start by using twrp,wipe everything 3 times...and just install the Rom of choice..I'm using padawan v3..then just installed the newest modem...then restart and let it sit for 10 min...if you still have problems then check your apn.if still not working call straight talk and have them reset your account
- GNote via Tapatalk 2[/QUOTE]
Hey guys, still no luck.
I have little to no problems when using 2g and on gsm mode, but when on full 4g, I have issues, internet cuts out and calls act up when traveling. Calls take long to start, etc.
Could it be a bad flash when the phone was first rooted? I just dont understand why I seem to be the only person with this problem. =(
nycokla said:
Really? I'm still having issues. Should I try flashing with cwm instead Of twrp?? I tried what you guys said above and still no good. Man this sucks!!
Click to expand...
Click to collapse
I would start by using twrp,wipe everything 3 times...and just install the Rom of choice..I'm using padawan v3..then just installed the newest modem...then restart and let it sit for 10 min...if you still have problems then check your apn.if still not working call straight talk and have them reset your account
- GNote via Tapatalk 2[/QUOTE]
When you say wipe everything, does this mean data, cache, dalvik, factory reset, system and even the internal sd card (emmc) where my music and files is stored?
Also, does it matter where I flash my rom from, I have been flashing it from the emmc rather than my sd card, is that a bad thing??
Just to set a bench, move everything from internal to external sd, then wipe internal, then wipe everything aside from external..then install rom from sd
- GNote via Tapatalk 2
hi guys i am having trouble with the mobile network on just this rom. i only have 3g in this area (cant wait till january so i cant test lte, but it is most likely the rom. i just cant get the phone to connect to mobile network. do i need to flash newer radio? other stock moded roms work fine. No good on cyan mod 10 roms ethier
You could try disabling it from looking to LTE service in the mobile networking options - Maybe they happen to be turning it on to test and your phone is trying to connect?
It's under Settings => <More> => Mobile Networks => Network mode => Change to CDMA / EvDO auto
I already tried changing no luck thanks for reply
Very similar in theory.. But also try this.
Go to the dialer, hit *#*#4636#*#*, go to phone information, and change to CDMA auto (prl) in the drop down list there.
regalpimpin said:
Very similar in theory.. But also try this.
Go to the dialer, hit *#*#4636#*#*, go to phone information, and change to CDMA auto (prl) in the drop down list there.
Click to expand...
Click to collapse
I'll try this when I get some time. Also is any one having same the same problems as I am? if you are NOT can you tell me exactly how you flashed the rom and gapps (if u did?) Also what kernal and radio you are using
spaghettiknight said:
I'll try this when I get some time. Also is any one having same the same problems as I am? if you are NOT can you tell me exactly how you flashed the rom and gapps (if u did?) Also what kernal and radio you are using
Click to expand...
Click to collapse
Tried all of the options in drop down menu none will
Worked
Some people are talking about earlier builds having more stable 3g can someone link me with like a 10/29 build or something
315 view no reply?
spaghettiknight said:
315 view no reply?
Click to expand...
Click to collapse
11/24 has been good to me
spaghettiknight said:
I'll try this when I get some time. Also is any one having same the same problems as I am? if you are NOT can you tell me exactly how you flashed the rom and gapps (if u did?) Also what kernal and radio you are using
Click to expand...
Click to collapse
I flashed rom then gapps, got this. then wiped and gapps then rom... same thing
I am now on SuperLTE and the problem has followed me...
Kernel 3.0.8-07680-gb6402b4
PRI = 2.45-003
PRL = 25006
I got a thread over here too about this:
http://forum.xda-developers.com/showthread.php?t=2014105
When I'm running cmx and have connection issues I usually toggle roaming in settings while its set 3g only[no lte)... This has worked for me. When I establish a connection I turn back on the 4g late radio and I'm good to go
Sent from my EVO using xda premium
regalpimpin said:
Very similar in theory.. But also try this.
Go to the dialer, hit *#*#4636#*#*, go to phone information, and change to CDMA auto (prl) in the drop down list there.
Click to expand...
Click to collapse
what happens if this is what is up there on that screen when i try to ping after I switch to all of those drop down items
Ping IpAddr: Fail IP addr not reachable
Ping Hostname(www.google.com): Fail: Host unreachable
HTTP Client test: Fail: IOException
Signal Strength: -63dBm 16 asu
Update:
So i dig some digging and found out that my GPRS service was disconnected here>
Did some more digging and found this:
http://www.nexusoneforum.net/forum/nexus-one-tech-issues-bug-reports/8254-gprs-service-mobile-network-state-disconnected.html
banccalif said:
11/24 has been good to me
Click to expand...
Click to collapse
ya i tried that got it to work. now I am having the issue where when i receive multiple mms's In one single text
(i got mms to send and download using an alternate apn found in Baffles thread under android development if you cant get it to work try rebooting after you restore the apn)
the app itself tries to open it as a slide show then instantly closes, this is a problem with the app since i downloaded an alternate messaging app and it worked fine. the reason i care is because i wanted to have the stock app working due to the "reply in notification bar" feature. can you guys try out receiving multiple messages sent at the same time from one phone to another and see if it works or if any one can link me to a working CM10 apk messaging app
Please go to this Url to reply ------> http://forum.xda-developers.com/showthread.php?p=35326334#post35326334
Cherokee4Life said:
I flashed rom then gapps, got this. then wiped and gapps then rom... same thing
I am now on SuperLTE and the problem has followed me...
Kernel 3.0.8-07680-gb6402b4
PRI = 2.45-003
PRL = 25006
I got a thread over here too about this:
http://forum.xda-developers.com/showthread.php?t=2014105
Click to expand...
Click to collapse
try the CM10 12/4 nightly or try using this guide on changing the APN ( it will say that the fix is for mms but should affect both
Ok so i have the tmobile sim in my verizon phone I am using the fast.T-Mobile.com apn settings I'm in a 4g area. My issue is my phone rapidly changes from h+ to 3g, to 4g lte and very seldom edge..... Fyi happens as I'm at work so I'm stationary. Data works but kinda lags at times. Any thoughts as to why or what to do??? And I have tried ipv4/6 and just each respectively. Thanks in advance.
If you are set on global try switching to lte gsm utms only and see if that helps
deron37129 said:
If you are set on global try switching to lte gsm utms only and see if that helps
Click to expand...
Click to collapse
I'll give it a go in the morning. Thanks will let u know if it works.
The stock lollipop Rom has an issue with syncing hangouts and gmail. In order to force sync,IPv6 is manually disabled every 1 minute. When that happens, your data connection resets, and you see your phone go up through the speed technologies.
jfsat said:
The stock lollipop Rom has an issue with syncing hangouts and gmail. In order to force sync,IPv6 is manually disabled every 1 minute. When that happens, your data connection resets, and you see your phone go up through the speed technologies.
Click to expand...
Click to collapse
Well that sucks lol. What would you recommend? I'd just like to stop cycling through the data 4g, 3g ect.
SBAKER24 said:
Well that sucks lol. What would you recommend? I'd just like to stop cycling through the data 4g, 3g ect.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=59514506&postcount=2921
This is probably what you seek, but a word of warning; I haven't tried any of this myself. I don't know whether this will work or break your phone. If I were trying to do this, I would probably just comment out that second line (put a '#' in front), but if you start getting sync problems, this will probably be why.
jfsat said:
The stock lollipop Rom has an issue with syncing hangouts and gmail. In order to force sync,IPv6 is manually disabled every 1 minute. When that happens, your data connection resets, and you see your phone go up through the speed technologies.
Click to expand...
Click to collapse
The thread you posted seems to,only refer to Wi-Fi issues and syncing.... I am not connected to Wi-Fi. I read that when they disconnect Wi-Fi there phones are fine with data..... Not sure I wanna delete anything like that off my phone when I'm not,sure off this will help. Of I went back to stock kk would I still have this issue?
SBAKER24 said:
The thread you posted seems to,only refer to Wi-Fi issues and syncing.... I am not connected to Wi-Fi. I read that when they disconnect Wi-Fi there phones are fine with data..... Not sure I wanna delete anything like that off my phone when I'm not,sure off this will help. Of I went back to stock kk would I still have this issue?
Click to expand...
Click to collapse
Theoretically you won't still have this problem if you go back to KK. I haven't gone back to KK since I took the plunge into LP, so don't quote me on that. In fact, if you just install the stock LP ROM, you won't have this problem any more as well.
OR, you could install Jasmine 5.0, and then upgrade it to something like 5.0.7 or 5.0.8, which ever one was before the IPv6 fix started getting baked into the Rom. That's probably what I would do, but I haven't tried SkyDragon yet, so I don't know what I'm missing.
jfsat said:
Theoretically you won't still have this problem if you go back to KK. I haven't gone back to KK since I took the plunge into LP, so don't quote me on that. In fact, if you just install the stock LP ROM, you won't have this problem any more as well.
OR, you could install Jasmine 5.0, and then upgrade it to something like 5.0.7 or 5.0.8, which ever one was before the IPv6 fix started getting baked into the Rom. That's probably what I would do, but I haven't tried SkyDragon yet, so I don't know what I'm missing.
Click to expand...
Click to collapse
Think I'll give jasmine 5.0 a spin. I noticed there is a 5.0.11 changelog says disable the 10 and 1 minute ipv6 not sure if I should try it out or not :/ http://forum.xda-developers.com/showpost.php?p=59517503&postcount=2929
SBAKER24 said:
Think I'll give jasmine 5.0 a spin. I noticed there is a 5.0.11 changelog says disable the 10 and 1 minute ipv6 not sure if I should try it out or not :/ http://forum.xda-developers.com/showpost.php?p=59517503&postcount=2929
Click to expand...
Click to collapse
If you don't like the Edge > 3G > H+ > LTE, don't use 5.0.11, I'm on that, and it happens to me. I'm also Unlocked and on the T-Mobile network, just like you. It didn't happen to me at all before the IPv6 stuff started going into the Rom. And I also didn't have any sync issues.
jfsat said:
If you don't like the Edge > 3G > H+ > LTE, don't use 5.0.11, I'm on that, and it happens to me. I'm also Unlocked and on the T-Mobile network, just like you. It didn't happen to me at all before the IPv6 stuff started going into the Rom. And I also didn't have any sync issues.
Click to expand...
Click to collapse
Trying to get Jasmine 5.0 installed how didbu go about it? Looks like I can't the normal twrp flash way. I'm looking into it now.
SBAKER24 said:
Trying to get Jasmine 5.0 installed how didbu go about it? Looks like I can't the normal twrp flash way. I'm looking into it now.
Click to expand...
Click to collapse
You'll have to follow the steps from the 5.0 post. Extract the files to /sdcard/ and then do some shell commands in TWRP. Takes you out of your comfort zone a little, but it worked for me.
jfsat said:
You'll have to follow the steps from the 5.0 post. Extract the files to /sdcard/ and then do some shell commands in TWRP. Takes you out of your comfort zone a little, but it worked for me.
Click to expand...
Click to collapse
I just got it installed. It was a bit different but its up and running. Now i need to find the versions you said lol.
SBAKER24 said:
I just got it installed. It was a bit different but its up and running. Now i need to find the versions you said lol.
Click to expand...
Click to collapse
This one might be the one you're looking for. And you can install is in TWRP like any normal file
http://forum.xda-developers.com/showpost.php?p=59469705&postcount=2746
jfsat said:
This one might be the one you're looking for. And you can install is in TWRP like any normal file
http://forum.xda-developers.com/showpost.php?p=59469705&postcount=2746
Click to expand...
Click to collapse
Perfect!!! Thanks. I got it loaded up now i am getting all my data back up on the phone.