Hi all, my Prime is stuck at the Asus splash screen out of nowhere! I looked through these q & a, googled, and tried a few simple options before i posted this.I was not trying to flash a new rom or anything like that. I actually hadn't used it for a few days because i'm moving, i charged it up, used it for a few hours, came back later to use it, and the browser froze. No big deal, it does that once every day or two. I hold the power button to restart it and now it just stays at the flash screen. I haven't tried to flash anything in so long i forgot for a bit how to access recovery or what exact rom im using. I can access recovery(twrp 2.2.2.1) and fastboot, i remember unlocking without a problem, and doing the nvflash backup on ics before i believe i flashed a stock jb rom(which i think i'm still on.) I was able to copy my pictures to an external sd card through twrp , and after that i tried to restore a backup, and wiping data and cache but still stuck at the splash screen. Any help would be greatly appreciated, right now im going to look through and see if i can find the stock jb rom, or lookup fastboot guides or something. Thanks for any help!
I flashed this rom and got it up and running. I love this forum! w00t http://forum.xda-developers.com/showthread.php?t=1927494
Related
OK:
Briefly, Running fine on VEGAn 7 RC 1 with Pershoot's latest. When the Tab was running and booting, I made a full backup in CWMod.
Screwed around with some permissions and once I rebooted, ended up at VEGAn Tab pulsating Boot Screen. It would do its thing for a minute or so, screen would go blank and then return immediately to the same VEGAn Tab screen (i.e., not a full boot).
Not a problem, right? I just booted into CWMod, cleared out everything and restored my earlier backup.
No go. Same loop at the VEGAn screen.
I searched the forums a lot, so either I am not very good at searching or this has not been addressed.
Advice would be appreciated, as this is not the first time I have been here and want to learn if there is a way to repair it (obviously, I can reflash ROM+Kernel) restore via Titanium and only have a little manual recovery left to do.
Thanks!
I had the same thing happen to me while i was changing around roms. I know its not the exact thing but regardless. Anyways, try mounting your tab in cwm as USB and pull your back up off the tabs memory. Go back to cwm and wipe everything, then repartition to advised settings. Remount your tab as usb and put the back up back on your drive and restore again. It may work.
Sent from my VEGAn-TAB using Tapatalk
iamjakecali said:
Not a problem, right? I just booted into CWMod, cleared out everything and restored my earlier backup.
No go. Same loop at the VEGAn screen.
Click to expand...
Click to collapse
If its something simple, clearing the Dalvik Cache in CWM might fix it.
I appreciate the ideas. Unfortunately i have tried then all. One of the times this has happened i was messing around with the old two taps xoom. Of i knew anything about the really technical stuff i might speculate something to do with boot loader.
Oh for anyone here who bricks, Don't freak... sometimes i do several times a day and have always come back from it ... mostly using the advice of all the brilliant people here, occassipnaly by messing around with adb, and once i let my monkey push random keys since he had already managed to compose a sonata...
ok so yesterday i rooted my telus fascinate and i was going to isntall the MIUI rom. Following a guides instructions i installed rom manager and did a clockwork mod recovery, i then put the rom on my root file of my sd card and tried to install it through the "install rom from sd card option" on the app. Problem was i only got into the stock recovery mode and not the clockwork one it aslo gave me signature failures. I then followed the guide of this video:
http://http://www.youtube.com/watch?v=Q7xV0yE9ZcA
when i installed the kernel everything went fine but then after i got into CW recovery and installed the rom my phone booted and it just kept repeating the normal splash screen (it said galaxy I9000 instead) followed by a screen that said something like cryogenic mod. I got freaked out from here and tried to install stock kernels to get my phone running. As of right now my phone will boot but only stay on the splash screen. I can not access recovery mode. I really need some help, thanks.
these are some of the files i used:
the rom i used,
http://http://forum.xda-developers.com/showthread.php?t=1150045
the kernel i used,
http://http://forum.xda-developers.com/showthread.php?t=822756
thanks
the links are broken. Did you install a rom / kernal specifically for the telus fascinate?
i believe it could have been for the galaxy I9000,
ill try to fix the links btw
update*
i managed to get it into clockwork recovery mode by holding the dam buttons for a solid 5 minutes, after doing this i pressed factory reset, now my phone is stuck saying:
-- wiping data...
Formatting DATA
0_0' im not having a great day
http://forum.xda-developers.com/showthread.php?t=1227807Until I know what version miui and kernal you are trying to flash, it's hard to help. It definately sounds like your phone is soft bricked tho.
Edit* Here are some links you should read up on.
http://forum.xda-developers.com/showthread.php?t=923712
http://forum.xda-developers.com/showthread.php?t=1227807
try to type this inot your browser:
http://forum.xda-developers.com/showthread.php?t=1150045
aswell as this:
http://forum.xda-developers.com/showthread.php?t=822756
it takes a little longer but i cant fix the links sorry.
So as of now i got i managed to wipe all of the data on my phone and i am in recovery mode, if i click reboot it does the same thing and stays on the boot screen. If i click the mod from the sd card it flashes from the normal model number screen to one saying cryogen mod. It then keeps going back and forth with a flash of a screen that has a bunch of commands on it for about 2 seconds
brodydj said:
try to type this inot your browser:
http://forum.xda-developers.com/showthread.php?t=1150045
aswell as this:
http://forum.xda-developers.com/showthread.php?t=822756
it takes a little longer but i cant fix the links sorry.
So as of now i got i managed to wipe all of the data on my phone and i am in recovery mode, if i click reboot it does the same thing and stays on the boot screen. If i click the mod from the sd card it flashes from the normal model number screen to one saying cryogen mod. It then keeps going back and forth with a flash of a screen that has a bunch of commands on it for about 2 seconds
Click to expand...
Click to collapse
The rom you are trying to flash is for a i500 fascinate. I suggest taking the time to do alot of research before you turn the phone into an expensive paperweight. Read this link!!
http://forum.xda-developers.com/showthread.php?t=921285
K well i ran that rom and it works now but he only problem is i dont have any cell service, do you know how to fix that. I know that you are probably laughing at my mild retardism at this subject but i am a big noob. As for what you said in your previous reply is their an MIUI version for the fascinate from telus because i basically rooted my phone so i could get this rom.
thanks
Update*
i followed the instructions on the link you posted and chose the rom for MIUI I9000 as the one i was going to install but when i istall zip from sd it only says installed correctly and then when i reboot it keeps changing from the sgh-t959d to the galaxy s cyanogen screen
yea your boot looped now. I would run the rom that worked just install the compatible radio and kernal for it and you should get cell service back.
ok thanks i got all my cell service back and i got the MIUI rom to work. Now to just ry to remember all the apps i had
Your welcome...glad you got everything working!
So, SGH-177 had been rooted and installed CM7, then Unnamed, then AOKP. All were pretty buggy. We wanted to bring it back to factory (with root if possible). Not for a warranty claim, just so it would be somewhat stable.
Anyway, I found a one click ODIN solution for UCKH7 stock. I used that, it passed. then the phone just looped through the AT&T "Rethink Possible" splash screen. I tried to get into recovery mode, but it wouldn't load, so I flashed the Siyah kernel to get CWM on there. Still I can only get into download mode and the phone loops the splash screen.
I hoped that it was just taking some time to load up the first time, so I left it overnight. Still stuck on the splash screen this morning.
I spent hours on here last night and found lots of people saying that if you have access to download mode, or recovery mode, you should be able to fix it. I wasn't able to find any answers as to how.
Help?!
I've had this same problem before. what always fixes it for me is to get into the factory 3e recovery to do a reset. I know you said you couldnt get there but make sure (while the phone is off; remove battery if you have to before this) you are holding down both Volume buttons and the power button at the same time until you see the "Samsung Galaxy SII" screen, then release the buttons.
factory reset, then it should be fine.
If you can't get to recovery, read some more on here. I'm sure something is out there, but I don't know what it is.
Here are two posts that might help you out. I've been doing the same research since my "Oh crap its stuck in a bootloop I'll sell it cheap on eBay" SGII is due to arrive today or tomorrow.
http://forum.xda-developers.com/showthread.php?t=1451590
http://forum.xda-developers.com/showthread.php?t=1580885
Best of luck to you!
UnNamed buggy?
Out of curiosity how did you root and flash, cause that is probably one of the most stable builds we have with minor changes to stock.
Anyways good luck getting back to stock.
So, for some reason, the next time I tried booting into recovery, it worked. I got a couple errors, but then it booted up just fine. Don't know why it wouldn't get into recovery before.
Everything seems to be working as it should so far.
I'm guessing this may be why some of the threads I had seen didn't really offer a solution. Sometimes it finally works if you just hold your head right.
Thanks all!
Regarding UnNamed... I don't recall the method I used to root, it's been a long time and I've done various work on this (my wife's phone) and my Nexus One. Easy to get it confused. I flashed it through CWM recovery, factory wipe, flash from SD.
It worked fine for a while (a couple months), then it got really glitchy. Unable to answer phone calls, random reboots, etc.
Major Wood said:
I flashed it through CWM recovery, factory wipe, flash from SD.
It worked fine for a while (a couple months), then it got really glitchy. Unable to answer phone calls, random reboots, etc.
Click to expand...
Click to collapse
Did you also wipe cache and dalvik? May have been the problem...
I don't recall, but would be surprised if I hadn't done that
A year ago. When I first started flashing roms. I spent an entire week just reading the atrix forums and learning. I planned. I schemed. I asked questions. Through pm. And googled a LOT. Then when I had learned enough I did it. Point is....if yer not willing to have patience and learn as much as u can before u jump into this. Then its maybe not for you.
Sent from my SGH-I777 using Tapatalk 2
I am a relative noob at flashing roms and rooting phones, but last night I ran into an issue. My phone was having all sorts of problems so I was going to put it back to factory, then start from scratch. I then decided to just flash a different rom. here is what happened.
I deleted SuperSU - this was done as part of the process to unroot and put back to factory, after this step I decided to flash a different rom
Put new ROM on phones internal memory as well as SD card
Wipe data
wipe cache and delvic cache
install new rom
Black screen
In an attempt to unbrick I relocked my bootloader.
Now, my phone can power on (Give white screen and HTC logo), then go black, and I can access Recovery mode. That is all.
I have plugged the phone to my computer and tried running the RUU, but the RUU will not recognize the phone.
I am not sure what to do to unbrick my phone and get it working again. Any and all help would be most appreciated!
Sorry I can't be more eloquent with my words, but I'm at work. I will be responding throughout the day, though.
thanks again so much to anyone that can help!
Try running it straight from bootloader
I loaded into Bootloader, selected Fastboot(USB), ran the .exe and it still won't recognize the phone. However, I did get recovery unlocked again. So I can get into recovery mode, flash all the ROMs I want, mount and unmount, yet still everytime I flash a new ROM it still boots to a black screen. Am I doing this right?
Try a Rom with kernel installer
Thanks! Since I am still a little new could you tell me how I would spot a ROM with kernel installer or could you point me to any one that could work? From then, it's the same process as flashing any other ROM? Do I need to do something with the kernel?
Meanbean and stock with goodies are the 2 that I'm certain of. Meanbean needs to be flashed twice the first time
Thanks so much for your help, I will post my results soon!
Failed
Here's what it says. Sorry for the blurry picture. I followed directions closely.
What version of recovery are you using? You may need to update it. Assuming you have a pc, try mounting the internal memory to pc through twrp. Windows will automatically tell you to format if its damaged
2.1 Updating now
omg it finally worked! Updated TWRP using fastboot and flashed MeanBean. Thank you so much!!!
While trying to load a rom, I got a failed message, damn cat ran across the desk and it rebooted, I was to the point I should of flashed the overlay, did NOT make it that far. It boots up to the welcome screen, but I have no access to hit "start" as my touch screen is not working. Is it done for? I cant see it any longer in adb devices, so I cant continue where I left off. Linux cant see it at all. Windows knows its there. So it did not make a complete fash, it tried to reboot into stock i assume, looks stock. What can I do at this point? Any help would be great.
deleted
I got in. I can not enter fastbootd, and do not know where its saved. Can some one help me get my recovery back? I flashed a recovery backup, but it comes up witht he little dead andriod and no command error. I need to get to fastbootd. Any help would be wonderful.
If you can get into fastboot, isn't there a tool, LMSA rescue to bring back bricked device? wipes all data though.
Were you trying a custom ROM or stock? try booting to fastboot mode, power + vol-down, and fastboot flash the stock boot.img, can be found here: https://mirrors.lolinet.com/firmware/moto/sofia/official/
hope this helps. I just got the phone yesterday, soft bricked trying to flash magisk, flashed stock boot and was back in business. I was not using any type of custom rom though.
I was able to find stock boot and recovery images, which allowed me to just start over. Here is an screen shot of what would happen when flashing any ROM.
That's two different attempts. With two different errors.
On a crazy note, I ordered and got in the exact same phone off eBay, has lineage os, magisk, twrp. Now from what I've read, twrp can't be used to install ROMs yet. I've actually tried it on the problem phone we are working on here, but can't swipe with it. The screen is not correctly responsive. Yet this eBay phone, works great... Not sure how he did it. Id love to figure this out, I can't let it beat me.
klloyd said:
I was able to find stock boot and recovery images, which allowed me to just start over. Here is an screen shot of what would happen when flashing any ROM.
That's two different attempts. With two different errors.
On a crazy note, I ordered and got in the exact same phone off eBay, has lineage os, magisk, twrp. Now from what I've read, twrp can't be used to install ROMs yet. I've actually tried it on the problem phone we are working on here, but can't swipe with it. The screen is not correctly responsive. Yet this eBay phone, works great... Not sure how he did it. Id love to figure this out, I can't let it beat me.
Click to expand...
Click to collapse
I would try this next: https://support.lenovo.com/us/en/downloads/ds101291-rescue-and-smart-assistant-lmsa